Uncle Milton Fireflies In My Room User Manual
AAA /L R0 3
AA/ LR 6
Batteries not included
x2
Requires 2
x 1.5V AAA/LR03
Batteries not included
x3
Requires 3 x 1.5V AA/LR6 batteries
batteries
FIREFLIES
FIREFLIES
IN MY ROOM
IN MY ROOM
Hanging Light-up Fireflies
6+
2162
Includes:
TM
5 Hanging leaves
I Mounting hardware set
I Remote Control
7 Fireies
1 Center leaf
2 Side leaves
I Mounting plate
I Foam tape
On/O switch
g. 1 g. 2
Battery Installation
Tool required - Small Phillips head screwdriver.
1. Using a Phillips head screwdriver, loosen the screw in the battery
cover and remove the battery cover as shown.
2. Insert 3 "AA" batteries (not included) as indicated in the battery
compartment into the Center Leaf and 2 "AAA" batteries as indicated
in the battery compartment into the Remote.
3. Replace battery cover and tighten screw.
4. Switch the On/O switch to the "ON" position.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Caution: changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Assembly
1. Connect side leaves as shown (g. 1).
2. Run the 4 LED Cables through channels and
holes in leaves as shown (g. 2).
BATTERY SAFETY INFORMATION
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Different types of batteries or new and used batteries are not to be mixed.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Do not dispose of batteries in re. Battery may explode or leak.
WARNING:
CHOKING HAZARD - Small parts.
Not for children under 3 years.
Adult assembly required.
Mounting to ceiling
Tool required - Drill, 7/16" drill bit, small screwdriver
NOTE: THIS STEP SHOULD BE DONE BY AN ADULT.
NOTE: PRODUCT IS ONLY INTENDED TO BE INSTALLED ON A HORIZONTAL DRYWALL CEILING.
BECAUSE OF VARIATIONS BETWEEN BUILDING MATERIALS AND CONSTRUCTION METHODS,
THE INCLUDED MOUNTING HARDWARE MAY NOT BE SUITABLE FOR ALL INSTALLATIONS.
1. Determine the hanging location, being aware of ceiling stud locations. IMPORTANT!
Make sure the mounting location is at least 20 inches from any walls or obstacles to
ensure necessary clearance for hanging leaves (g. 3).
2. Using the mounting plate as a template, place the mounting plate against the ceiling with
the side marked "THIS SIDE DOWN" facing you. Using a pencil, mark the two outer holes.
3. With the markings you have made, drill two 7/16" holes all the way through the drywall.
4. Insert the hardware through the mounting plate as shown noting side labeled "THIS SIDE
DOWN."
5. Insert hardware through ceiling as shown (g. 5).
Ceiling
20" 20"
g. 3
g. 4
Mounting Plate
CeilingCeiling
1"
6. Gently maintain a downward pull on the mounting plate while screwing the hardware
clockwise until the plate is snug against the ceiling. Do not over tighten (g. 5).
7. Guide the three legs on the top of the Center Leaf into the corresponding holes on of the
mounting plate (g. 6).
8. Rotate the Center Leaf clockwise until you feel it click into place (g. 6).
Final assembly
1. Connect the remaining 5 Hanging Leaves by plugging the LED Cables into the back of
the leaves. Press rmly until you feel the Cable Connector snap into place (g. 7).
2. Remove self adhesive backing and apply squares of foam tape to underside of reies
(g. 8).
3. Locate the reies as desired onto the smooth surface of the leaves as shown making
sure the rear end of the rey is tting snugly against the LED. Press the each rmly into
place (g. 8).
Operation
IMPORTANT: The On/O switch located on the Center Leaf, must be switched to the
"ON" position.
g. 5
g. 6
g. 7
Mounting Plate
CeilingCeiling
Mounting Plate
1. Press the button on the Remote to turn on.
2. To turn o, press and hold the Remote button.
Note: To conserve battery life, the reies will turn o automatically after 30 minutes.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD
Questions? Visit unclemilton.com
MANUFACTURED BY UNCLE MILTON INDUSTRIES, INC.
P.O. Box 6281
THOUSAND OAKS, CA 91359 USA
©2012 UMI. All rights reserved. ® and
trademarks of Uncle Milton Industries, Inc.
MADE IN CHINA
TM
designate
g. 8
2162-0250-0 412-V 02
Loading...