Cantilever Flat Panel Bracket
Installation instruction for 803B
TV Size:36 -65""
Tilt :-5/15
Max Load capacity:132lbs/60kgs
Wall Distance:5.8 -22.8"/147-580mm"
Bubble level system Included
Universal Mounting Pattern
Hardware kit:
Tools Required:
PLASMA MOUNT INSTALLATION AND OPERATION INSTRUCTION
√
√
√
√
Phillips Head Screw driver
Stud finder for drywall installation
Socket and Wrench
Electric drill masonry bit for concrete/brick installation
A
B
C
D
E
F
(×4) M6×16 screw
(×4) M8×16 screw
(×4) M5×35 screw
G
H
I
J
K
L
M
(×4) M6×35 screw
(×4) M8×35 screw
(×4) M8/M6/M5 Washer
(×4) M8 Bolt
(×4) M8 concrete anchor
(×4) M8 Washer
(×4) M8 Spacer
N
(×4) M5×16 screw
(×2) M6 concrete anchor
(×4) M6 Bolt
(×4) M6 Washer
Note:
1 You need rivet the bubble level system onto the wall plate before installing
2 Please check the two rails before installing,if without the knob as showed, please
first detach the screw and install the knob.
Step1: Wall plate installation
Wood Stud Installation
NOTE:For secure wood stud mounting,the wall plate must be mounted to two studs at least 16"apart.
Concrete/Brick Installation
The concrete anchors must be used for concrete installation.
NOTE:
1 Begin by placing the wall plate into position against the wall,
using the bubble level to keep it level.
2 Mark off 6 holes to be used for securing the mount and
place the wall plate aside
3 Next , drill holes four 8mm holes 40mm deep(M6 bolt J) and
four 12mm holes 60mm deep (M8 bolt I)
4 Insert a concrete anchor(K)into to reach hole.
5 If necessary, a hammer can be used to lightly tap each anchor
into place so that they are flush with the wall.
7 Attch the bolt(I/J) into the anchor(H) that is placed in the wall.
8 Do not tighten until all screws are in plate .
1 Use a high-quality electrnic stud finder (commercially available) to locate two adjacent studs and
mark their locations with a pencil.
2 With the help of an assistant, and using the bubble level to ensure the wall plate is level, position
the wall plate against the wall in the desired mounting location.
3 Mark the right, upper and lower and the left (upper and lower) positions of the small horizontal slots
that are in alignment with the studs.
4 You should mark eight positions total as the picture showed.
5 Next, Pre-drill four 3mm hole 30mm deep on the up wall plate for M6 bolt (J) and four 5mm holes
50mm deep for M8 bolt(I) as showed following.
6 please position the wall plate against the wall and line up the mounting slots with drilled holes
7 For each location, insert a lag bolt (I/J)and washer(L/M)into the wall.
8 Tighten bolt with an open ended socket wrench by turning clockwise until tight.
IMPORTANT:If you don't understand how to install the product,
please consult a specialist
6 Once all of the anchors are in place ,move the wall plate back into position.
Ple ase add t he back c over
fir stly as t he pict ure
BALANCE-ADJUSTING
J
I
M
L
I
L
(J)M6X80
3mm
5mm
30mm
60mm
(I)M8X80
H
G
M
L
I
J
(J)M6X80
8mm
12mm
40mm
60mm
(I)M8X80
BALANCE-ADJUSTING
Step2 Display bracket Installation
1 To ensure optimal installation,this kit includes various screws of differe diameters and lengths.
2 Place your TV screen down on a soft,flat surface,and locate the threaded mounting points that are
located on the back of the display.
3 Determine which screw (A/B/C/D/E/F)is of the correct length by carefully inserting a straw, or
toothpick,and mark how deep the mounting point is.
4 If your display has a curved back or a recessed thread mounting point, a spacer(N) must be used.
5 Place the spacer(N) between the mounting bracket and display.
6 According to the size of display's hole,choose the corresponding screw and hole on the rectangle
washer,then thread them in line.
Step3 Final Installation & adjustment
1 Hook the TV Rails over the top of the wall plate. The TV Rail could be tilted from -5 to 15 degree.
Tighten the middle screw on TV rails by wrench to adjust the tilting hardness.
Also you could swivel it to left&right.
2 It can be balance adjust by loose and tighten the four behind M8 Nuts with 3 degrees.
3 lock it to avoid the theft through rotating the key until the hook touch the bottom bar of the wall plate.
N
K
D,E,F
A,B,C,
D,E,F
K
3-a
add plastic cover
STOP
CAUTION:
Do not over-tighten bolts-doing so many cause unnecessary damage to the wall.
Avoid excessive torque.
Do not release the wall plate until it is properly mounted and secured to the wall.
CAUTION:
M8Nut
+
-
3
O
umount,Unit 2 Lon Parcwr Business Park,Ruthin,
Denbighshire,LL151NJ-www.umount.tv
M8 SC REWS
M8 WA SHE R
M8 NU T
ADD T HE H EAD
Loading...