U-Media WMD-360A User Manual

802.11g Wireless MIMO miniPCI Module

User's Guide

1

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.

2

This device is intended only for OEM integrators under the following conditions:

U-MEDIA declares that WMD-360A, ( FCC ID: SI5WMD360A ) is limited in CH1~CH11 for 2.4 
GHz by specified firmware controlled in U.S.A.

1) The antenna must be installed such that 20 cm is maintained between the antenna

and users, and

2) The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID
product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users (for
example : Access Point, Router…etc.). The final end product must be labeled in a visible
area with the following: “Contains TX FCC ID: SI5WMD360A”.

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end user

transmitter test will not be required.

can not be met (for example

can not be used on the final

regarding how to install or remove this RF module in the users manual of the end
product which integrate this module.

The users manual for OEM integrators must include the following information in a prominent location “ IMPORTANT NOTE:
To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.

3

Distance between two external antennas on housing is 15cm, and PLS refer to the
following picture for antenna position.

4

Table of Contents

Federal Communications Commission Interference statement____1

Getting Started_____________________________________________4

About Your 802.11g/b WLAN MIMO mPCI______________________4

Configuring Wireless Security_______________________________4

Configuring Security_____________________________________4
Configuring WEP__________________________________________4
Configuring WPA-PSK______________________________________7
Configuring WPA__________________________________________8
Configuring 802.1x_______________________________________8
Configuring 802.1x – EAP-MD5_____________________________8
Configuring 802.1x – EAP-LEAP____________________________9
Configuring 802.1x – EAP-PEAP____________________________9
Configuring 802.1x – EAP-TLS_____________________________11
Configuring 802.1x – EAP-TTLS___________________________13

5