UMC Various Models User Manual

Download

Page 1

User Guide

Page 2

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

IMPORTANT SAFETY INSTRUCTIONS

Warnings

• To reduce the risk of ﬁ re, electric shock or damage

to the television, do not expose it to dust, rain or moisture, or place any objects ﬁ lled with liquids on or near the television.

• Do not place the television in a conﬁ ned space,

ensure that nothing can obstruct the ventilation openings at the rear of the television.

• Dispose of this television and any components

including batteries in an environmentally friendly manner. If in doubt, please contact your local authority for details of recycling.

Safety

• For your safety, this appliance is ﬁ tted with a fused

moulded 3 pin mains plug. Should the fuse need to be replaced, ensure that any replacement is of the same amperage and approved with the BSI mark.

• Never try and replace the mains plug unless

you have adequate qualiﬁ cations and are legally authorised to do so. In the event that a replacement Mains cable is required, contact the manufacturer for a suitable replacement.

• Never use the television if it is damaged in

any way.

• Always place the television on a ﬂ at level surface

avoiding anywhere which may be subject to strong vibration.

• Ensure the television is not placed on top of the

power cable as the weight of the television may damage the cable and cause a safety hazard.

• Never place mobile phones, speakers or any

other device which may cause magnetic or radio interference with the television. If interference is apparent, move the device causing the interference away from the television.

• To disconnect the apparatus from the mains,

please use the switch located on the underside/rear of the TV. The switch shall remain readily operable.

• When installing on a wall, ensure the TV is at least

5cm from the wall for ventilation.

Maintenance

• To clean this unit, wipe with a soft, dry cloth. If the

surfaces are extremely dirty, use a soft cloth dipped in a soap and water solution or a weak detergent solution.

• Never use alcohol, paint thinner or benzene to

clean this unit.

• Before using a chemically treated cloth, read the

instructions that came with the cloth carefully.

CAUTION: If water or other liquid enters the television through the display panel surface, a malfunction may occur.

Packaging

• The safest way to transport your item is in

the original box/packaging - please save your packaging for this.

• You will need original box/packaging in the event

of warranty/service repair or support. We are unable to carry out warranty/service if you are unable to package it correctly.

To prevent spread of ﬁ re, keep candles or other open ﬂ ames away from this product at all times

Please read these instructions. All the safety and operating instructions should be read before the appliance is operated.

Page 3

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

IMPORTANT SAFETY INSTRUCTIONS

Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays

The extended use of ﬁ xed image program material can cause a permanent “shadow image” on the LCD/LED panel. This background image is viewable on normal programs in the form of a stationary ﬁ xed image. This type of irreversible LCD/LED panel deterioration can be limited by observing the following steps:

1. Reduce the brightness/contrast setting to a minimum viewing level.

2. Do not display the ﬁ xed image for extended periods of time.

3. Turn the power off when not in actual use.

Examples of images that you need to watch out for are as follows (this is not an exhaustive list):

• TV Channel Logos: e.g. Shopping channel logos

and pricing displays-especially if they are bright and stationary. Moving or low-contrast graphics are less likely to cause ageing of the screen.

• Time Displays

• Teletext: Do not view a stationary page for a

long period of time

• TV/DVD Menus: e.g. Listings of DVD disc content

• Pause Mode: Do not leave the TV in pause mode

for long periods of time, e.g. When watching DVDs or videos.

Important - Once ‘shadow image/screen burn’ occurs, it will never disappear and is not repairable under warranty.

How do I dispose of this product?

UK: Waste electrical products should not be

disposed of with household waste. Separate disposal facilities exist. For your nearest facilities, please see www.recycle-more.co.uk or in store for details.

ROI: Waste electrical products should not be

disposed of with household waste. Separate disposal facilities exist. Check with your Local Authority or retailer for recycling advice.

Batteries

• Do not expose batteries to high

temperatures, excessive heat, prolonged sunshine or ﬁ re as this may cause leakage, explosion or ignition.

• Observe the correct polarity when

inserting batteries.

• Do not use different types of

batteries together or mix old and new batteries.

• Dispose of batteries in an

environmentally friendly way.

• Certain regions may regulate the

disposal of batteries. Please consult your local authority.

CAUTION:

THIS UNIT IS A CLASS 1 LASER PRODUCT. THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT

This caution label is located on the rear panel of the unit

TV Models with built in DVD players

Please read these instructions. All the safety and operating instructions should be read before the appliance is operated.

Page 4

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Page 5

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

ﬁ g 1

ﬁ g 2

Optimum viewing - if wall mounting the TV higher than eye level, the TV should be tilted downwards so that the TV’s screen is ‘face on’.

See ﬁ g 1 and 2

Important – If wall mounting this TV, only use the screws already provided in the wall mounting holes. Using other screws which are longer could cause irreparable damage to internal parts.

Viewing angle

INCORRECT

CORRECT

IMPORTANT - Before drilling any holes in the wall ensure you are not drilling where there could be any electric wires, water or gas pipes.

1) Remove the four screws highlighted below.

2) The wall mount can now be easily attached to the mounting holes on the rear of the TV. These holes are indicated in the picture below.

WALL MOUNTING

Getting Started - Initial Set Up

Page 6

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

TV Buttons and Source Menu

TV BUTTONS & SOURCE MENU

Choosing Mode Input/Source

To switch between the different input/connections.

A) Using the buttons on the remote control:

1) Press [SOURCE/ AV] - The source menu will appear

2) Press [\/] or [/\] to select the input you require.

3) Press [OK]

B) Using the buttons on the Television:

1) Press [SOURCE]

2) Scroll up / down using CH+/ CH- buttons to the input/source you require

3) Press Vol+ to change input/source to the one selected.

Example of Source menu

May vary by Model

Page 7

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Remote Control

STANDBY - Switch on TV when in standby or vice versa MUTE - Mute the sound or vice versa TV/RADIO - Switch to Freeview and switch between TV and radio in Freeview mode TV GUIDE - Opens the 7 Day TV Guide (Freeview mode) ATV - Switch to analogue TV source USB - Switch to USB source DVD - Switch to DVD source EJECT - Eject disc in DVD mode

REC - To record what is currently on television REC LIST - Opens the list of what you have previously recorded

- To restart the current chapter

- To advance forward to the next chapter

- To stop the playback

- To play in fast rewind mode

- To play in fast forward mode

- To play/pause (Pause live TV when USB Memory Stick is inserted)

SOURCE/AV - To display the input/source menu INFO - Press once for now/next channel information Press twice for programme information about current programme

- Allows you to navigate the on-screen menus and adjust the system settings to your preference MENU - To display OSD menu EXIT - To exit all menus NUMBER BUTTONS - 0 – 9 to select a TV channel directly.

- To return to the previous channel viewed

FAV - To display favourites menu

VOL - To increase / decrease the sound level SUBTITLE - To switch the dialogue at the bottom of the screen (on/off) ASPECT - To switch the screen between the different picture formats AUDIO - To change the audio language (if available) SLEEP - Press repeatedly to cycle through the sleep options CH To increase or decrease the channel being watched GOTO - DVD mode - To go to a speciﬁ c chapter A-B - DVD mode - Press once to set point, press a second time to return to point ANGLE - DVD mode - Select different angle of DVD (if available) REPEAT - DVD mode - To repeat playback

D.DIS - DVD mode - To display the current disc information ZOOM - DVD mode - To zoom in SIZE - Teletext mode - To change the display size in Teletext mode DISPLAY - To switch off the screen when listening to radio DVD SETUP/TEXT - DVD mode - To display the DVD setup menu Teletext mode - To enter Teletext D.MENU/INDEX - DVD mode - To display the DVD disc menu Teletext mode - To display the index page TITLE/REVEAL - DVD mode - To display the DVD title menu Teletext mode - To reveal or hide the hidden words. HOLD - Teletext mode - Hold current page which is displayed

REMOTE CONTROL WITH PVR & DVD

Page 8

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Remote Control

REMOTE CONTROL WITH DVD & USB

*DVD functions only available on 26’’ and 32’’ DVD Models. ** Teletext function is only available in analogue

*DVD - Switch to DVD source *EJECT - Eject disc in DVD mode

S.MODE - Scrolls through sound mode options P.MODE - Scrolls through picture mode options

- To restart the current chapter

- To advance forward to the next chapter

- To stop the playback

- To play in fast rewind mode

- To play in fast forward mode

- To play/pause

SOURCE/AV - To display the input/source menu INFO - Press once for now/next channel information Press twice for programme information about current programme

- To return to the previous channel viewed

FAV - To display favourites menu

*GOTO - DVD mode - To go to a speciﬁ c chapter *A-B Repeat - DVD mode - Press once to set point, press a second

time to return to point

*ANGLE - DVD mode - Select different angle of DVD (if available) *REPEAT - DVD mode - To repeat playback

*D.DIS - DVD mode - To display the current disc information *ZOOM - DVD mode - To zoom in

**SIZE - Teletext mode - To change the display size in Teletext mode DISPLAY - To switch off the screen when listening to radio

*DVD SETUP/TEXT - DVD mode - To display the DVD setup menu

**Teletext mode - To enter Teletext

*D.MENU/INDEX - DVD mode - To display the DVD disc menu

**Teletext mode - To display the index page

*TITLE/REVEAL - DVD mode - To display the DVD title menu

**Teletext mode - To reveal or hide the hidden words. HOLD - Teletext mode - Hold current page which is displayed

Page 9

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Remote Control

REMOTE CONTROL WITH PVR ONLY

REC - To record what is currently on television REC LIST - Opens the list of what you have previously recorded

- To restart the current chapter

- To advance forward to the next chapter

- To stop the playback

- To play in fast rewind mode

- To play in fast forward mode

- To play/pause

SOURCE/AV - To display the input/source menu INFO - Press once for now/next channel information Press twice for programme information about current programme

- To return to the previous channel viewed

FAV - To display favourites menu

TEXT - Displays teletext INDEX - Goes to teletext index page REVEAL - Reveals hidden text DISPLAY - To switch off the screen when listening to radio P.Mode - Cycle through different picture settings. SIZE - Teletext mode - To change the display size in Teletext mode HOLD - Teletext mode - Hold current page which is displayed S.Mode - Cycle through different sound settings.

Only operate when a USB key is inserted

Page 10

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Remote Control

REMOTE CONTROL WITH USB ONLY

S.MODE - Scrolls through sound mode options P.MODE - Scrolls through picture mode options

- To restart the current chapter

- To advance forward to the next chapter

- To stop the playback

- To play in fast rewind mode

- To play in fast forward mode

- To play/pause

SOURCE/AV - To display the input/source menu INFO - Press once for now/next channel information Press twice for programme information about current programme

- To return to the previous channel viewed

FAV - To display favourites menu

SIZE - Teletext mode* - To change the display size in Teletext mode DISPLAY - To switch off the screen when listening to radio TEXT - Teletext mode* - To enter Teletext INDEX - Teletext mode* - To display the index page REVEAL -, Teletext mode* - To reveal or hide the hidden words. HOLD - Teletext mode - Hold current page which is displayed

* Teletext function is only available in analogue

Only operate when a USB key is inserted

Page 11

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Remote Control

REMOTE CONTROL

STANDBY - Switch on TV when in standby or vice versa MUTE - Mute the sound or vice versa DTV - Switch to Freeview source RADIO - Switch to radio whilst in Freeview source USB - Switch to USB source DVD - Switch to DVD source

NUMBER BUTTONS - 0 – 9 to select a TV channel directly. TV GUIDE - Opens the 7 Day TV Guide (Freeview mode)

- To return to the previous channel viewed

VOL (+/-) - To increase / decrease the sound level P.MODE - Scrolls through picture mode options S.MODE - Scrolls through sound mode options FAV - To display favourites menu CH (+/-) - To increase or decrease the channel being watched MENU - To display OSD menu EXIT - To exit all menus

- Allows you to navigate the on-screen menus and adjust the system settings to your preference SOURCE - To display the input/source menu INFO - Press once for now/next channel information Press twice for programme information about current programme

ASPECT - To switch the screen between the different picture formats SLEEP - Press repeatedly to cycle through the sleep options AUDIO - To change the audio language (if available) SUBTITLE - To switch the dialogue at the bottom of the screen (on/off) TEXT - To enter/exit Teletext (Analogue TV) TEXT HOLD - Teletext mode - Hold current page which is displayed (Analogue TV) DISPLAY - To switch off the screen when listening to radio TEXT/DVD ZOOM - Zoom function for Teletext and DVD DVD MENU/RECORD - Access the DVD root menu and USB record function

- To restart the current chapter

- To advance forward to the next chapter

- To stop the playback/Eject Disc (To EJECT the disc press/hold the

button for 4 seconds)

- To play in fast rewind mode

- To play in fast forward mode

- To play/pause

DVD SETUP/REC LIST - Opens up DVD Menu or Opens the list of what has been previously recorded

GOTO - To go to a speciﬁ c chapter A-B - Press once to set point, press a second time to return to point ANGLE - Select different angle of DVD 3D - Change to 3D mode

REPEAT - To repeat playback

For Models with Integrated DVD players

For Models with PVR Function

For Models with USB Playback

For Models with 3D Feature

Page 12

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Connections

CONNECTIONS CONNECTIONS

Connecting to a Camcorder, Camera or Games Console

TV Source should be set to Video

Audio

R / L

Video

Connecting to a device with SCART output

TV Source should be set to SCART

SCART

OUT

SCART

RF IN

RF OUT RF IN

Page 13

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Connections

CONNECTIONS

Note: To use this model TV as a PC/laptop monitor it will need to be connected via the VGA input, it can not be used as a PC/laptop monitor via the HDMI input. The HDMI Input is provided to view digital content with compatible external devices

Connecting to a device with Component output

If you are supplied with a cable from the device which has RED, GREEN, BLUE, RED & WHITE connectors you must connect via Component (for picture) and by phono cable (for sound).

TV Source should be set to Component.

Connecting to a device with HDMI output

A HDMI cable can output both video and audio and enables you to enjoy digital-quality video and audio with minimal loss of quality.

TV Source should be set to the corresponding HDMI port (HDMI 1, HDMI 2 etc)

Page 14

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

TV Menu Operation

Tip: If you do not press any buttons for 30 seconds, the menu will automatically exit. You can change the length of time before the menu exits automatically - see ‘Menu Duration’ in the Setup Menu

CHANNEL MENU

Auto Tuning - Allows you to retune the television for all digital channels, digital radio stations and

analogue channels

Freeview Manual Tuning- Allows you to manually tune your digital signal

Analogue Manual Tuning - Allows you to manually tune your analogue signal

Programme Edit - Allows you to delete, skip and add favourite channels

Signal Information - Allows you to view signal frequency, signal quality and signal strength

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons.

To conﬁ rm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.

Page 15

TV Menu Operation

PICTURE MENU

Picture Mode - Choose from the following presets:

Ecohome Power saving mode which reduces the energy used by up to

25% (by reducing the power to the LED/LCD panel).

In Ecohome mode, the TV will switch itself to Standby mode

after 3-5 hours in the event that the TV buttons or remote

control buttons are not pressed (change the picture mode to

another setting to de-activate this function)

Standard Standard settings

Dynamic Recommended settings for fast moving pictures

Mild Set to be lighter in colour and less bright

Personal Lets you manually alter all the settings

You can make the following adjustments in

Personal mode:

Contrast - Switch the balance between black and white.

Brightness - Increase or decrease the brightness of the picture.

Colour - Increases the colour from black and white.

Tint - Lets you increase or decrease the level of tint within the picture

(only available in VGA/PC source mode).

Sharpness - Increase or decrease the sharpness of the picture.

Noise Reduction - Choose from the following presets:

Off Turns noise reduction off

Low Minor system adjustment

Middle Medium system adjustments

High Maximum system adjustments

Default Default settings

Colour Temperature Choose from the following presets:

Normal Default settings

Warm Increases red within the picture

Cold Increases blue within the picture

To access this menu, press [MENU] button on the remote control and scroll right. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons.

To conﬁ rm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.

Page 16

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

TV Menu Operation

SOUND MENU

Treble - To adjust the amount of high frequency within the sound

Bass - To adjust the amount of low frequency within the sound

Balance - To switch the sound between the left and right speakers

Auto Volume Level (AVL) - When ‘on’ is selected, the volume will attempt to stay at a constant level

regardless of TV programme and advertisements

Surround Sound- Switch Surround Sound ON or OFF

Sound Mode - Choose from the following presets

Standard Default settings

Music Emphasises music over voices

Movie Provides live and full sound for movies

Sports Emphasises sound for sports

Personal Selects your personal sound settings

Tip: Treble and bass levels can only be adjusted when the sound mode ‘Personal’ is selected.

Off To turn off Digital Output

Auto Selects the best settings automatically

PCM Select this option if you are connecting to a Stereo Hi-ﬁ via coax cable (Pulse-code

modulation (PCM) is a digital representation of an analogue signal)

AD Volume - Increase or decrease the Audio Description volume

Digital Output - This is the digital COAX Audio output. Choose from the following options:

To access this menu, press [MENU] button on the remote control and scroll right. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons.

To conﬁ rm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.

Page 17

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

TV Menu Operation

TIME MENU

Clock - Shows the date and time

Off Time - Allows you to set a speciﬁ c time for your TV to turn off

On Time - Allows you to set a speciﬁ c time for your TV to turn on, the channel it will then display, the

source it will be on and also the volume. This function can then be toggled to repeat every day or a

certain day (the TV must be in standby mode for this to be effective)

Time Zone - Change your current time zone

Sleep Timer - Lets you set the sleep timer so the television automatically switches off after a set amount of

time. Off -> 10min -> 20min -> 30min -> 60min -> 90min -> 120min -> 180min -> 240min

Auto standby - Set Auto standby between 3 hours, 4 hours and 5 hours ( to turn off this function you must

exit eco home mode in the Picture Menu)

To access this menu, press [MENU] button on the remote control and scroll right. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons.

To conﬁ rm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.

Page 18

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

TV Menu Operation

FEATURE MENU

Schedule List - Lists your programme reminders

PVR File System - Allows you to view format and performance of a connected USB key

CI Information - Pay per view services require a “smartcard” to be inserted into the TV

If you subscribe to a pay per view service the provider will issue you with a ‘CAM’ and a “smartcard”. The

CAM can then be inserted into the COMMON INTERFACE PORT (CI Card In)

System Lock - Allows you to lock or unlock the menu. You will be asked to enter a 4 digit password.

Use the

◄ button to quit the password input or use the ► button to clear. Default password is 0000.

Once the system lock menu has been accessed you can choose from the following options

Audio Language - Shows the current audio language

Subtitle Language - Shows the current subtitle language

System Lock Turns the System lock on/off

Key Lock Turns the Key lock on/off

Parental Guidance Turns Parental Guidance on/off

Default Source Select the Source the TV will be set to when the TV is switched on

Default Channel Select the Channel the TV will be set to when the TV is switched on

Source Lock Turns the Source lock on/off

Channel Lock Turns the Channel lock on/off

Max Volume Controls the maximum volume of the TV sound system

Change Password Changes the password to access the system lock options

To access this menu, press [MENU] button on the remote control and scroll right. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons.

To conﬁ rm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.

Page 19

TV Menu Operation

SETUP MENU

Menu Language - Allows you to change the language of the menu

Blue Screen - Changes the background when there is no input between clear and a blue background (Only

available on some sources)

Menu Duration - Lets you adjust the amount of time the On Screen Menu stays on the screen before

disappearing

Reset to default

Reset Menu System

- This resets the menus to factory settings.

Reset TV Channels - This clears all the TV channels from the television.

Software Update (USB) - From time to time we may release new ﬁ rmware to improve the operation of

the television (available to download). This menu lets you install the new software/ﬁ rmware onto the

television. Further details of how to do this will be issued with the ﬁ rmware. Contact the helpline or refer

to the ‘product support’ section of the website

Auto

Automatically displays the best picture format. So the picture is in the correct position. May have black lines

at the top/bottom and/or sides.

Zoom

Original

16:9

The picture is the correct proportion but zoomed in to ﬁ ll the screen

Will display the picture from the broadcaster without any change

Stretch

Aspect Ratio - Within the UK the picture format

varies depending on the channel/broadcast. There are a number of different options to best meet your needs

4:3

Displays the 14:9 picture in the correct proportion. As a result side bars are shown on the screen

Displays the 4:3 picture in its original size. Side bars are shown to ﬁ ll the 16:9 screen

Fills the screen with a regular 16:9 signal and 4:3 picture format will be stretched to ﬁ ll the screen

To access this menu, press [MENU] button on the remote control and scroll right. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons.

To conﬁ rm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.

Page 20

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

DVD MENU (DVD ONLY)

To access this menu, press [MENU] button on the remote control.

If you wish to make changes to any of the default settings, use the scroll

buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

TV System - Choose from the following options

NTSC Normally used for discs from North America, Japan etc

PAL The standard for discs from UK/Europe, most of Asia, Australia etc

Auto For both NTSC and PAL

TV Type - Choose from the following options

4:3PS

Traditional picture format, often used on old ﬁ lm

4:3 LB

Traditional picture which has been adapted for widescreen

16:9 Widescreen picture format

Default - This option allows you reset all DVD settings to factory settings.

Tone - Choose from the following options

+ Increases the treble (high frequency sound)

- Increases the bass (low frequency sound)

Dynamic Range - This is the difference between the quietest and loudest sounds. This setting works only

with DVD discs recorded in Dolby digital. Full Set this to listen with the range recorded on the disc

4/8 Set this to listen with a range equivalent to a normal television

2/8 Set this to listen with a smaller difference between the maximum and minimum volume

Dual Mono

Stereo Outputs 2 channels of sound both left and right

Mono L Outputs left side sound

Mono R Outputs right side sound

Mix Mono Outputs a single channel of sound but mix between right and left

Tip: This TV/DVD player is pre-set to play Region 2 DVDs. In the event you wish to use the TV/DVD in another country that uses different region discs, please visit www.skymediauk.co.uk. Select ‘Product Support’, ‘Changing Region’.

DVD Menu

Page 21

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

PC SETTINGS

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

Auto Adjust - Lets you automatically conﬁ gure the television to be used as a computer monitor

H Offset - Changes the horizontal position of the picture

V Offset - Changes the vertical position of the picture

Size - increase picture size

Phase - To adjust delay time of phase in order to reduce the noise of picture

Position Reset - Changes back to the original settings

Tip: If the computer is left in-active for a period of time, the television will switch into a ‘sleep’ state (the screen will power off to save power). To switch back on press the standby button.

PC Operation

Page 22

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

7 Day TV Guide

Notice for PVR models only

This TV is designed to operate with USB memory sticks up to 32GB. It is possible to use either a USB memory stick or a USB portable Hard Drive of a larger capacity, however, it must be formatted to the FAT32 ﬁ le system in order to operate correctly. At the time of printing this user guide, Windows XP/Vista computers are only capable of formatting up to 32GB, therefore, you will need a software programme/utility to format larger USB drives/hard drives to FAT32. Additional help and support is available from the web site.

7 DAY TV GUIDE

TV Guide is available in Digital TV mode. It provides information about forthcoming programmes (where supported by the freeview channel). You can view the start and end time of all programmes and on all channels for the next 7 days and set reminders.

1) Press [TV GUIDE]. The following 7 Day TV Guide will appear.

2) Navigate through the menu using

You can now: Record a programme by pressing RED (PVR ONLY - USB device must be connected) Set a reminder by pressing GREEN View a previous day by pressing YELLOW View the next day by pressing BLUE

3) Press [EXIT] to exit the 7 day TV Guide.

EXIT

Page 23

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

USB Record

USB RECORD - DIGITAL/FREEVIEW MODE

USB RECORD – DIGITAL/FREEVIEW MODE Built into this television is a USB record facility. This function is available in Digital/Freeview mode when used in conjunction with a compatible USB memory stick or USB Hard drive. The beneﬁ ts of this are as follows:

• Pause live TV and then playback, fast forward and rewind (up to live TV)

• One button record, if you decide you want to record the current programme

• Easy programmable recording from the 7 day TV Guide

• Record TV and watch/listen back on your computer/laptop

Due to the nature of the product, it is necessary to use a high speed USB memory stick (as the TV reads from and writes to the memory stick at the same time, some memory sticks may not be suitable)

You can purchase high speed memory sticks from some computer stores, alternatively, we have a selection of tested and compatible memory sticks available to purchase directly from the helpline/web site.

Minimum Speciﬁ cation - USB Memory Stick

Read Speed 20 MB/s (Mega Byte Per Second)

Write Speed 6 MB/s (Mega Byte Per Second)

If you wish to use a USB portable hard drive larger than 32GB, please refer to the FAQ section at the rear of this user guide.

Tip: When you switch the TV to standby or change channel the Time Shift memory is wiped. To restart time shift you must press play/pause button.

Tip: This television contains one TV tuner, therefore it can only record the channel you are watching or record one channel while the television is in standby mode.

Note: USB record function is only avilable in Digital/Freeview TV mode. Due to copyright laws and illegal copying/recording it is not possible to record to/from any other input/output source.

Pause Live TV (Time Shift)

Pausing Live TV is very simple.

- Press the play/pause button and the television will pause and the live

content will be recorded. To resume watching press play/pause again.

- Press fast forward to go forward in a recording (i.e. to skip adverts)

- Press fast rewind to go back in a recording (i.e. if you fast forwarded too

far)

One Button Record

At any point in time you may decide to record the current channel that you are watching. To do this you need to press the red button highlighted below.

Page 24

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

USB Mode / Media Player

1) You can navigate through the menus using the scroll

buttons. To conﬁ rm the item you

wish to play/view press [OK] button.

2) Select the drive you require. (If your drive only has 1 partition you will only see 1 item).

3) You can now access the item. Press OK to view. 4) While viewing you control the item using or by pressing ( i ) and using and (OK)

USB mode offers playback of various different types of content that you have saved on your USB Memory Stick.

On switching to USB source the above menu screen will appear. The content will be divided into Photo, Music, Movie and Text based on ﬁ le type.

USB MODE / MEDIA PLAYER

Tip: If you experience a playback issue, please ensure the ﬁ les being used are the correct format (example - the picture plays but no sound) See technical speciﬁ cation page for compatible ﬁ le types

Page 25

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

General Information

USING YOUR TV WITH A SKY DIGITAL SET TOP BOX

Option 1) Connecting your TV to your Sky box (when both the TV and Sky Box are located in the same room)

Depending on your Sky Box & TV model, connect either by SCART or HDMI cables (available separately)

If connecting by SCART, select the ‘Input source’ on the TV as SCART.

If connecting by HDMI, select the ‘Input source’ on the TV as HDMI (if the TV has more than 1 HDMI port, ensure you select the input source to match the HDMI numbered port on the rear of the TV)

If you wish to use your Sky remote to operate the TV’s functions, you will need a Sky remote control (Revision 9 or later) and you will need to programme a 4 digit code into it. See bottom of this page.

Option 2) Connecting your TV to your Sky box (when your Sky box is located in a different room to the TV)

Please note, if you are adding a ‘Magic Eye/TV Link’ to your system so that you can use your Sky remote control to change the Sky channel in the room where the 2nd TV is located, please refer to the instructions included with the TV link/magic eye in order to ensure the RF or RF2 output on your Sky box is powered on. (The red LED light on the TV link/magic eye will light up if the RF / RF2 output is correctly set up) If you do not have the instructions that came with the TV link/magic eye, instructions on how to do it can be found on our web site.

1) To tune the TV to the Sky box, on the 2nd TV, select the ‘Analogue’ input source.

2) Select the channel that you wish to store the Sky box/channel on. (If you do not use channels 1-5 because you

no longer have analogue terrestrial channels after digital switchover, you may choose to select channel 1 to store the Sky box/channel, if you still have and use analogue channels 1-5, you may for example decide that channel 6 is the best option for you)

3) Press the corresponding number on the remote control to select the desired analogue channel chosen as per

point 2 above.

4) On the TV remote control, press Menu. Now navigate through the menus to select Manual Tuning or Analogue

Manual tuning (refer to the Tuning/Channel menu section of this user guide if necessary)

5) Manually tune in the channel (usually, the Sky box is at a frequency between 800Mhz and 850Mhz) once the

Sky box/channel is found, press ‘OK’ to store it.

If you wish to use your Sky remote to operate the TV’s functions, you will need a Sky remote control (Revision 9 or later) and you will need to programme a 4 digit code into it. See below.

Sky Box

SCART or HDMI cable

RF/COAX cable from Sky Box to 2nd TV

Connect to RF or RF2 output on the Sky box

Connect to the Aerial/RF input on the 2nd TV

TV Link/Magic Eye (optional)

2nd TV in another room

Sky Box

SCART or HDMI cable

Using a Sky Remote or a Universal Remote to operate your TV

Sky Remote Control - If you wish to use your Sky remote to operate the basic functions of your TV, you need to

programme a 4 digit code into it. Please note - you will need the latest Sky Revision 9 remote control as this is the only version that includes the latest software/ﬁ rmware necessary to operate this model of TV. The code required for this television is 2134. If you wish to upgrade/replace your existing Sky remote control to the latest version, you can do so on our web site.

Universal Remote Control - If you wish to use a Universal remote control to operate your TV, please refer to the website for a full list of codes. (Please note we only have codes for One for All branded remote controls, if you have an alternative brand of Universal remote, please refer to the manufacturer for the code.)

Page 26

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

FREQUENTLY ASKED QUESTIONS

General Information

For various models

General I would like to have louder

sound by connecting additional speakers

1) Use the 3.5mm headphone output and a 3.5mm to phono cable (available separately) to connect to an ampliﬁ er/surround sound system. Please note this will deactivate the TV’s built in speakers.

2) Connect a COAX cable from the TV’s COAX output to your ampliﬁ er/surround systems COAX input.

General Why are some options in

the menu unavailable and greyed out

Some options are only available in certain sources, i.e. HDMI. They are unavailable in the other sources where they have no affect.

General Can I stop my TV automatically

turning off after 4hrs?

Yes

1) In the picture settings menu, de-select Eco-home.

2) In the time settings menu, scroll down to Auto standby and select OFF.

TV I have tuned in Digital TV

but I am not receiving any or all of the channels and/ or the channels I receive are breaking up

1) Check you are in an area that can receive Freeview. Visit www.freeview.co.uk

2) Check you are using an aerial that is able to receive a good digital signal. In most cases, you will need an outdoor digital hi-gain/wideband aerial. In areas that have excellent digital coverage, you may be able to use a loft type aerial but it is highly likely that you will also need to connect a booster between the back of the TV and the TV aerial wall socket. Unfortunately, to receive a good enough digital signal, it is not possible to use a portable/indoor type aerial.

TV I have re-tuned my television

but when I switch it off it is not storing the channels

Complete a ﬁ rst time installation, please refer to the set-up menu section of the manual of how to do this.

VCR/DVD Recorder

I have connected the TV to my VCR or DVD Recorder via SCART but it is not recording

In addition to connecting via SCART, you should connect the aerial cable from the wall socket to your VCR/DVD Recorder and another aerial cable from the VCR/DVD Recorder to the TV.

Game Consoles I have connected my PS3 to

the TV via HDMI, but I am not receiving any pictures or sound on my Television

1) Ensure the TVs source is on HDMI.

2) Check your settings on your PS3 are as per the PS3 instruction manual.

Game Consoles I have connected my

Xbox 360 to the TV via Component Cables (Red, Green & Blue) but I am not receiving any sound

Component cables only provide HD Pictures. For the sound you will need to connect the Red & White audio cables on the Xbox to the Red & White phono inputs on the rear of the TV. Please refer to the ‘Connections’ pages.

USB Mode I have inserted a USB

Memory Key, but the TV does not recognise it

Ensure the USB Memory Key is formatted to type FAT32.

USB Mode Using a USB portable hard

drive / larger than 32GB

If you wish to use a portable hard drive larger than 32GB, please note that it must be formatted to the FAT32 ﬁ le system in order to operate on this TV. Windows XP/Vista computers are only capable of formatting up to 32GB, therefore, you will need a software programme/utility to format larger hard drives. Please refer to the web site for more information.

System Lock I have changed the password

on the television and now forgotten it

There is a master password of 4711, to gain access to the TV menu and reset the normal password.

Page 27

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

General Information

USB Record / TV models only

I cannot change the channel, access the menu or use the red button

During Time Shift you cannot change the channel, access the menu or use the red button

USB Record / TV models only

When using the USB to record the picture ‘breaks up’ or experience loss of sound.

Check the USB Memory Stick meet the minimum requirements of Read Speed - 20 MB/s (Mega Byte Per Second), Write Speed - 6 MB/s (Mega Byte Per Second)

For DVD Models only

For PVR Models only

FREQUENTLY ASKED QUESTIONS

DVD I have inserted a disc but it is

not playing

1) Ensure you have inserted the disc facing the correct way.

2) Ensure the disc is clean and is not scratched.

3) Some copied discs will not play.

4) Check the DVD is a region 2 disc – to change the region of the DVD player, refer to www.umc-uk.co.uk select ‘product support’, ‘changing region’.

DVD I have pressed the eject

button but the disc is not coming out

To eject the disc hold the stop/eject button for 4 seconds.

Page 28

Helpline No UK. 0871 2000 463 ROI. 01443 3940

Web Support: www.umc-uk.co.uk

Media File Ext. Codec

Video Audio

Movie .mpg Mpeg-1, Mpeg-2

MP3, WMA

Max Resolution: 1920x1080 Max Data rate: 40Mbps

.avi Xvid, MJPEG,

MPEG-4 SP/ASP

.ts Mpeg-2 Max Resolution: 1920x1080

Max Data rate: 40Mbps

.mov Mpeg-4 SP/ASP

.dat Mpeg-1

.mp4 Mpeg-1, Mpeg-2 Max Resolution: 1024x768

Max Data rate: 40Mbps

.vob Mpeg-2

Music .mp3 - MP3 Sample Rate 16K-48KHz

Bit rate: 320Kbps

.wma - WMA

Picture .jpg Progressive JPEG Max Resolution: 1024x768

.jpeg Baseline JPEG Max Resolution: 8192x8192

.bmp BMP Max Resolution: 6500x6500

COMPATIBLE FILES IN USB MODE

Page 29

UMC Various Models User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual