For Quick installation instructions, see the section “Quick Start Guide” starting on page 6.
Trademarks
IBM PC/AT is a trademark of International Business Machines Corporation. MS-Windows, Windows, and
MS-DOS are trademarks of Microsoft Corporation. Mac OS, iMac, iMac DV, Mac G3/G4, G4 Cube and
Mac Series are trademarks of Apple Computer, Inc. Other names and trademarks appearing herein are
trademarks of their respective holders.
Important Safeguards
Read all of the instructions.
Follow all warnings and instructions marked on the product.
Do not use this product near water or in rainy/moist environment.
Do not place the scanner on an uneven surface, which may cause serious damage to the product.
The product should be operated only from the type of power source indicated on the marketing label.
Use of power supplies not conforming to these standards can cause serious damage to the product.
Do not attempt to service this product yourself as opening or removing the enclosure may expose you
to dangerous voltage or other hazards.
The sound level at the operators position according to IEC 704-1:1982 should be less than or equal to
70dB(A).
1
CONTENTS
A GLANCE AT YOUR SCANNER……………………………………………………………..3
THE FRONT VIEW……………………………………………………………………………….3
THE REAR VIEW…………………………………………………………………………………3
1. Document Cover
The plastic cover over the object glass which can be raised and lowered over a document.
2. Carriage Lock
Before operating the scanner you must move the locking switch to the unlocked position.
3. Power Indicator
Illuminates to indicate that the scanner is powered on.
4. Object Glass
The glass surface on which the document or image should be placed.
The Rear View
5. 4-Pin USB connector
6. IEEE
1394(PC)/FireWire(MAC) Connector
7. UTA
For use with a transparency adapter.
8. Power Adapter Receptacle
The power adapter is plugged in here.
3
9. Power Switch
Turn the scanner power switch on. When the Power Indicator is on, your
scanner is ready to use.
Quick Start Guide
This section serves as a quick reference to the connection and installation procedures for the PowerLook
1000 scanner.
CAUTION:
Find a suitable location near your computer to place the scanner. Use of longer, unsupported cables
may cause connection problems and data loss.
Make sure the scanner is resting on an even, flat surface. Operating your scanner on an uneven surface
can cause damage to the internal components.
There are tow kinds of interfaces on the back of your scanner. They are IEEE 1394 (for PC)/
Firewire (for Mac) and USB interface. Connect the scanner to the computer using only one of the
two.
Software Installation
For PC users:
1. Insert the PowerLook 1000 CD into your CD-ROM drive.
Note: If a window does not appear automatically, double-click the My Computer icon to
open it, double-click the PowerLook 1000 CD-ROM icon to open it as shown in picture A
(please be aware the PowerLook 1000 CD is labeled “MagicScan” in the Windows
desktop/directory).
2. Follow the on-screen instructions to complete the installation of the applications on your CD.
Please Note: the computer will automatically install each application individually once you
begin the process.
4
3. Restart your computer as suggested by the on-screen instructions. Once your computer
restarts, click the ‘X’ in the upper right corner of all open windows to close. You are now
finished installing the applications on the PowerLook 1000 CD.
For users of APPLE Macintosh computers:
1. Install the scanner driver by inserting the scanner CD into the CD-ROM drive of your
computer.
2. Double-click on the scanner CD installer icon. Follow the on-screen instructions to install the
drivers.
3. Restart your computer.
Hardware Installation
Step 1. Unlocking the Carriage
1. Before operating the scanner, please unlock the restraint.
2. To better access the lock switch, remove the document cover by lifting it up from the scanner.
3. To unlock the restraint, move the carriage lock toward the unlocked position as shown above.
Note:
When transporting or shipping the scanner over a significant distance, be sure to relock the optical
assembly to avoid damaging it. Before re-locking the assembly, make sure the optical assembly of the
scanner is in the “Home Position” by doing the following:
1. Turn the scanner off and then on again.
2. Wait for the ready indicator of the scanner’s to light up.
3. Turn off the power of the scanner again. The optical assembly should be in the Home Position.
4. To lock the optical assembly, move the carriage lock until it points to the locked symbol.
5
Step 2. Connect the Cable
For PC Users:
Connecting the USB Cable (Most systems)
1. Locate the USB cable that is provided. Plug the wide end of the cable firmly into one of
the available USB ports on your computer.
2. Plug the small end of the cable into the port marked “USB” located on the back panel of
the scanner as shown in picture C.
Connecting the IEEE 1394 Cable (If your PC is equipped with a IEEE 1394 interface)
1. Connect one end of the IEEE 1394 cable into the port located on the back panel of the
scanner.
2. Connect the other end of the IEEE 1394 cable to one IEEE 1394 port of your computer.
6
Loading...
+ 12 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.