Ultravation 70-003, 70-004 Owner's Manual

DC-IH-0210

Page 2- Shipping and Packaging list, Introduction and Application, Safety Precautions, Installation Requirements
Page 3- Maintenance, Germicidal UVC Lamp replacement, General Dimensions
Page 4- Warranty, Replacement Part Numbers

PHOTRONIC UVMatrixTM CW Series

Standalone Air Cleaning System

OWNERS GUIDE

Models: 70-001, 70-002, 70-003, 70-004

Table of Contents:

LEAVE FOR HOMEOWNER

p

Shipping and Packaging List:

• Filter Housing including Access door

• Ultra-Ion Re-fresh PCO module

• MERV-11 or HEPA Media air filter

• 1” pre-filter

• 2- 20” 55 Watt UVC lamps

• 4- Eye Bolts and nuts

• 4- Galvanized Unit hangers

• 4- ¼ 20 stainless steel bolts

Introduction and Application

This Ultravation UVMatrix CW series is a stand alone air
cleaning system utilizing high efficiency air filtration
designed to remove dirt, dust, pollen, microscopic particles
and reduce unpleasant odors, VOC gases as well as
reduce microbial population from the air that circulates
through it.

The system works in 3 steps ­First by trapping particles in a pre-filter, then in the pleats of

the MERV 11 or HEPA media filter. With an extra large
surface area, the filter allows for maximum dirt holding
capacity and a long, useful filter life with minimum air flow
restriction.

Second VOC’s and gases such as the fumes from new
carpets, paints, nail polish, cigar and cigarette smoke are
drastically reduced photo chemically via a patented
process known as photo catalytic conversion or photo
catalytic oxidation.

Third Germicidal UVC light is applied to the Air and
problematic to drastically reduce unwanted Virus, Bacteria
and Mold.

:

Safety Precautions:

It is recommended that this unit be installed and
maintained by a trained technician:

WARNING: UV Hazard. Always protect eyes from
ultraviolet light. NEVER look at UV lamps in
operation. Unplug or disconnect power before re­lamping or servicing.

WARNING: Severe eye damage or temporary
blinding may occur.

WARNING: DO NOT operate outside of Air Handler.
Mount lamp base to duct first.

WARNING: No openings in duct are allowed which
would give direct line-of-sight to the UV light.

In the event of accidental breakage when replacing the
ultraviolet lamp, please ensure that the lamp is
disposed of in accordance with local and state
environmental laws regarding fluorescent lamps
containing mercury.

Notice:

All wiring inside of the duct or air handling system in
direct line of site of the UV lamp must be shielded with
aluminum foil tape or equivalent non-combustible
material. When installing this unit, select a mounting
location that prevents ultraviolet light exposure to
plastic flexible duct liner or other plastic components
with unknown resistance to ultraviolet light. Ultraviolet
light may cause color shift or structural degradation of
plastic HVAC components

Installation Requirements:

* The UVMatrix CW unit is designed to be installed in a
2’ x 4’ suspended ceiling grid for low profile
applications or installed as a wall mount or hung from
the ceiling.

1. Determine a suitable location to install unit.

2. If installed in ceiling grid, use supplied eyebolts for
support and insert into ceiling grid in appropriate
location (Unit needs to suspend independent of
ceiling grid).

3. If installed on wall – mark out spacing of key holes
and install supplied screws into wall. Put supplied
mounting tabs in corner locations.

a. Hang unit on keyholes and secure by

mounting through corner tabs.

4. Unit comes with a 120V power cord. If ceiling
mount is used, remove power cord via access
panel and hardwire into terminal strip.

5. Insert UVC Lamps and Photo Catalytic Cartridge.

6. Turn on unit via ON/OFF switch and set fan speed
using variable speed fan control and inspect
o

eration.

2