Bubble Master
Operator’s Manual
www.ultratecfx.com
VER. 04.11.12
Table of Contents
Warning ...................................................................................... 3
Safety Precautions ..................................................................... 3
Technical Specications ............................................................. 4
Technical Drawings ................................................................... 4
Operating Procedure ................................................................. 5
Shut Down Procedure ................................................................ 5
Troubleshooting ......................................................................... 5
Maintenance ............................................................................... 6
Recommended Fluid .................................................................. 6
Warranty ..................................................................................... 7
Contact Information .................................................................. 7
www.ultratecfx.com
2
Note: Please read entire manual before operating the Bubble Master
Warning
Important Safety Instructions:
1. Do not remove the outer case.
2. Ensure that this unit is grounded at all times. Failure to do so may result in serious injury.
3. Use Ultratec Special Effects uid ON LY.
Safety Precautions
1. Ensure that any operation of the machine is supervised by suitably trained and authorized personnel.
2. Do not modify the machine or use a machine which has been damaged in any way.
3. Allow sufcient air circulation around the machine at all times.
4. Protect the machine from direct weather effects and wet locations.
5. Only use uids manufactured by Ultratec Special Effects.
6. Avoid directing bubble output continuously at people, structures or objects within close proximity of the
discharge nozzle.
www.ultratecfx.com
3
Technical Specications
Model: Bubble Master
Part Number: CLB 2012 / 120 Volt
CLB 2015 / 120 Volt - w/ FDS Option
CLB 2014 / 220-240 Volt
CLB 2018 / 220-240 Volt – w/ FDS Option
Length: 28.4in 72.1cm
Width: 16.3in 41.4cm
Height: 15.8in 40.1cm
Net Weight: 21lbs 9.51kg
Power Rating: 120 Volt A.C. 50/60 Hz. 1 Amps.
240 Volt A.C. 50/60 Hz. 0.5 Amps.
Fluid: Water Base Bubble Fluid (Use only Ultratec Fluid)
Approvals: Field Certication Q.P.S.
*Dimensions include Bubble Projector
Technical Drawings
www.ultratecfx.com
4
Operating Procedure
Unpack the Bubble Master and inspect all components. Although the
packaging was designed for the rigours of today’s parcel delivery services,
damage may have occurred during shipping.
1. Prior to operation, the extension sleeve may be placed over the bubble
outlet. This will allow the bubbles to be projected higher, before they
begin to disperse outwards.
2. For lower ying bubbles do not use the extension sleeve.
3. Place the Bubble Master on a level sturdy surface, or use the optional
adjustable stand sold separately.
4. Open a container of Ultratec Bubble Fluid, and pierce the foil top. Pour
the uid into the bubble outlet. Fill up to 1/2” below the reservoir top.
This initially should take approximately 1 gallon.
5. Plug the Bubble Master into an outlet that is capable of sustaining the
current load listed on the product serial plate.
6. Use the Fan Speed Control knob to start the bubble wheel and fans,
and to control the fan speed. By varying the fan speed you can control
the bubble volume, size and height.
Fill to 0.5in below reservoir top.
Do not overll past top of reservoir.
Pour uid in bubble outlet
Shut Down Procedure
1. Disconnect the Bubble Master from the power source.
2. Remove the bubble extension sleeve if used.
3. Using a funnel, empty the contents of the uid reservoir back into the 1 gallon uid container. This can be done by
tipping the unit, and pouring the uid out of the bubble outlet.
4. Replace cap on the uid container to keep dirt and debris from entering.
5. Rinse out uid reservoir and bubble wheels with hot tap water tap water to remove excess bubble uid residue.
Using a paper towel wipe out extension sleeve and bubble outlet.
6. Empty into sink or appropriate drain.
Troubleshooting
Bubble Wheel not turning:
Ensure that set screws are secure in bubble wheel motor shaft.
Intermittent bubbles produced:
Ensure that there is enough uid in the uid reservoir, and that the bubble wheels are being submersed in bubble uid.
www.ultratecfx.com
5
Maintenance
Fluid Reservoir
When storing the Bubble Master for any extended period, be sure to thoroughly rinse the uid reservoir.
Bubble Wheel
When storing the Bubble Master for any extended period, be sure to thoroughly rinse bubble wheels.
Recommended Fluid
Bubble Master Bubble Fluid: This Premium Quality Bubble Fluid produces large quantities of bubbles that are very dry
and long lasting.
Bubble Fluid Supreme: This Supreme Quality Bubble Fluid produces large quantities of Bubbles that are longer lasting
and much drier than regular Bubble Fluids. This Bubble Fluid is recommended for applications that require a drier
Bubble Effect.
www.ultratecfx.com
6
Warranty
Warranty: Hardware products come with a one year warranty on parts and labor. Unless stated otherwise,
this will refer to manufacturer defects only. All warranty is based on destination of the original
sale. Any additional costs incurred are the responsibility of the Dealer and/ or the customer.
Abuse or poor maintenance is not accepted. Proof of purchase or proof of sale must always
accompany all warranty returns. An RA (Return Authorization) number must be noted on
the outside of each box being returned to our facility. Any package(s) without an RA number
clearly marked, will not be accepted by our receiving department. Freight on warranty items are
freight prepaid to our facility and we will prepay freight back to your facility following repair.
This will be done by the most economical means available. Should you require the item expressreturned, the dealer is responsible for request indication and any difference in freight cost.
Export Distributors are required to carry out the warranty repair, parts will be supplied by
Ultratec.
Return Policy: Return of any product must be done within 30 days of purchase. The package must be
returned freight prepaid and the RA number clearly marked on the outside of the box.
Warning: Ultratec Special Effects considers all of it’s product to be safe for use in the application it was
intended. Ultratec Special Effects takes no responsibility for misuse or incorrect use. Always
refer to the Product Manual for proper use.
Contact Information
Head Ofce
Ultratec Special Effects
1960 Blue Heron Drive
London, Ontario N6H 5L9
Direct: 519-659-7972
Toll Free: 866-534-5557
Fax: 519-659-7713
Europe Ofce
Ultratec Special Effects GmbH
Dieselstrasse 30-40
60314
Frankfurt am Main
Germany
Direct: 49-69-87-000-1850
Fax: 49-69-87-000-1899
Canadian Shipping Address
(For All Canadian Repairs)
Ultratec Special Effects
1960 Blue Heron Drive
London, Ontario N6H 5L9
Please remember to include the RA Number on all items being shipped
for repairs.
To retrieve an RA Number visit www.ultratecfx.com and click on the
“Service” section. Then click on “Return Authorization Request” which is
located on the left hand side of the page.
If you have any questions or require assistance please contact service at
519-951-3357/866-534-5557 or by email at Service@Ultratecfx.com.
USA Shipping Address
(For All USA Repairs)
Ultratec Special Effects
640 Gadson St, Unit 300
Groveland, Florida 34736
www.ultratecfx.com
7
Loading...