Ultra Start 600 User Manual

INSTALL GUIDE

600 Series Remote Vehicle Security System

WWW.ULTRASTARTERS.COM

Technical Support- 866.698.5872

FCC/ID Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance
void the user’s authority to operate this devise.

INSTALL GUIDE

SECURITY SYSTEM

PAGE 2

Table of Contents

Table of Contents Page 2
Components

600 Wiring Diagram Page 3

Installation Tips Page 4

Pre-Installation Suggestions

Installation Suggestions Page 4

Mounting The Module
Installing The LED
Installing The Program Button
Connecting The Starter Disable
Connecting The Dome Light Supervision
Under Hood Connections
Mounting The Siren

Wire Connectors Page 5

14 Pin Main Harness Connector
4 Pin Red Connector- Keyless Entry
2 Pin Connector Red- Plug-in LED
2 Pin Blue Connector- Plug-in Program Button
3 Pin White Connector- Aux. outputs
4 Pin White Connector- Additional sensor input

Installation Page 6-7

Basic Installation - Quick start
Shock Sensor Programming
Test The System

Programming Page 7-9

Program Overview & System Reset
Program Menu 1 (User Settings)
Program Menu 2 (Alarm Settings)

Operations Page 10

Single & Dual Car Operation
Transmitter Programming
Battery Replacement

Other Features Page 11

System Service Mode
Service Mode- By remote

Diagnostics Page 12

Components

-Control module - Starter Disable harness

- Remote transmitter(s) - Plug-in Valet Switch

- 14 pin main harness with - 4 pin Aux sensor harness
dual 30amp power inputs - Plug-in Led

- 4 pin Keyless Entry harness with - Multi-tone siren
Driver’s Door Priority output - Installation and owner manuals

SECURITY SYSTEM

Wiring Diagram

INSTALL GUIDE

PAGE 3

Built-in Starter Disable relay (Normally Connected 87a & 30). See page. 5

Programmable - Menu 2

Connect to hood pin

Connect to Siren

Connect to park lights

See page. 4

See page. 4

(-) Output while armed

(-) Trunk Release Output

Connect to main Ignition

Connect to chassis ground

12vt constant power

500ma Output

(-) InputConnect to (-) door pin

(-) Input

(+) InputConnect to (+) door pin

3amp Output

15amp Output

(+.-) Input

(+.-) Output

500ma Output

500ma Output

(+) Input

(-) Input

(+) Input

Channel 4

(-) Door Input

Hood Input

(+) Door Input

(+) Siren

(+) Park Lights

Dome Light Relay

Dome Light Relay

(-) When Armed

(-) Trunk Release

Ignition Input

Ground

Main Power

Pink

Green

Blue

Purple

Brown

White

Blk/White

Blk/White

Orange

Grey

Yellow

Black

Red

Starter
Disable

Main Alarm Harness

Programmable - See menu 1, Setting 3

12vt inverter Output-Low Current

Programmable - See menu 1, Setting 3

Programmable - See menu 1, Setting 3

(-)500ma Output

(+)500ma Output

(-)500ma Output

(-)500ma Output

Door Lock Output
12vts Low Current
Door Unlock Output
Priority Output

LED

Valet Switch

Negative Output When Disarmed

Programmable - See menu 2, Setting 7

Triggers when 12vt circuit is broken

Negative trigger input

Negative trigger input

Sensor ground output

Sensor power output

(-)500ma Input

(-)500ma Input

(-)500ma Output

(+)500ma Output

(-)500ma Output

(-)500ma Output

(+)500ma Input

Sensor Full - Warn
Sensor Pre - Warn

Sensor Ground

Sensor Power

**500ma outputs are low current and are designed to activate relays.

(-) When Disarmed
Horn/Channel5.
(+) Disconnect

Green

Red
Blue
Pink

SIDE VIEW

Green
Pink
Blue

Blue
Green

Black
Red

4

P

IN RED

-

2 PIN RED

-

2 PIN BLUE

3 PIN WHITE

4PIN WHITE

SATELLITE LINK PLUG

4

PIN

WHI

TE

INSTALL GUIDE

SECURITY SYSTEM

PAGE 4

Recommended Pre-Installation Procedures

BEFORE STARTING INSTALLATION:

- Discuss the optional system features with the customer.

- Take a few minutes to review the installation and owners manuals.

- Do a walk around the vehicle and check for any damage.

- If installing a LED discuss the placement with customer before installing.

Recommended Installation Procedures

Mounting the Module

Never mount the module in the engine compartment. Select a location under the dash to install the
main module. Be certain that the module is securely attached and does not obstruct any
serviceable areas. Mount the module so that it cannot be seen if looking under the dash as it
could be easily unplugged by a thief. The module must be free from all moving parts such as
brake, clutch and gas pedals linkages.

Installing The Led

Choose a location that will be highly visible when the LED is installed. Most vehicles are equipped
with knock out panels in the dashboard, these panels are easily removable and can be easily
replaced if necessary. Once the location is picked, use a 5/16th drill bit and drill a hole through the
panel. Test fit the LED into the hole. If the hole was drilled to large, place the LED in the hole and
glue in place from the back of the panel. Plug the Led into the Red connector on the main module.

Installing The Program Button

Choose a location to mount the Program Button. This location should be hidden and not visible from
outside the vehicle. Once the location of the switch is picked, use a 1/4” drill bit and drill a hole.
Remove the nut and push the Program button through the hole. Replace the nut and tighten until
the switch is secure. Plug the valet into the Blue connector.

Connecting The Starter Disable

This system contains a built-in Starter disable relay. The brown starter kill wire from the wire
harness bag will connect to the module as normally connected. (87a & 30) Cut the brown wire in
half, then locate the vehicles starter wire. This wire will switch to 12volts in the crank or start
position only. Cut this wire in half and confirm that the vehicle will not start. Connect the brown
wires, one to each side of the cut starter wire. Route the brown wires to the main module and
connect.

Determine the door pin type. Positive, door pin wire switches to 12 volts when the door is opened.
Negative, door pin wire switches to ground when the door is opened. For positive door, connect one
of the black/white wires to 12volts and the other to the door pin wire. For negative connect one of the
black/white wires to ground and the other to the door pin wire.

Mounting The Siren

Choose a location in the engine compartment that is away from high heat sources and direct
exposer to water. The siren should be mounted as well as grounded to solid metal. Run the wiring
for the siren so that it can not be seen or reached from below the vehicle.