How it Works
Ultra Start
Loading...
2500M SERIES
Installation Manual
16 pgs1.06 Mb0
Installation Manual
16 pgs1.6 Mb0
Owner's Manual
4 pgs842.06 Kb0

Ultra Start 2500M SERIES Installation Manual

2500
INSTALLATION GUIDE
Advanced Remote Vehicle
Starter & Alarm
2500
2500M
WWW.ULTRASTARTERS.COM
TECH SUPPORT
Installation Guide
TABLE OF CONTENTS
2500 Wiring Diagram Page 3 Pre-Installation Page 4
Components Recommended Pre-Installation Procedures Recommended Install procedures
Wire Connectors
6 Pin Connector 14 Pin Connector 3 Pin Red Connector 4 Pin Blue Connector Jumper Selections
Installation
Basic Installation - Quick start Plugging In The Module Auto Tach Learn Shock Sensor Programming
Programming Page 7-11
Program Overview & System Reset Program Menu 1 (User Settings) Program Menu 2 (Alarm Settings) Program Menu 3 (Starter Settings) Program Menu 4 (Tach Settings)
Other Features And Operations Page 12
Reservation Mode Transmitter Programming Battery Replacement Service mode Remote Service Mode Warranty
System Operation Page 14-15 Relay Diagrams Page 16
Page 5
Page 6-7
DIAGNOSTICS
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series of 3 Flashes Door Opened “M” Models 4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units 5 Flashes Series of 5 Flashes Hood Pin Grounded (Open) 6 Flashes Series of 6 Flashes Brake Pedal Shutdown 7 Flashes Series of 7 Flashes Tach Lock-Out 8 Flashes Series of 8 Flashes 3 Start Attempts with no start
If the remote starter has a failed start attempt or if a safety input is activated the Diagnostic Memory will store up to four shutdowns in memory. This information can then be accessed to determine the source of the shutdown.
To Enter Diagnostic Mode:
Step 1 - Turn the ignition on wait two seconds then turn off. Press the Program Button and release. Step 2 - The system will respond with three park light flashes and the siren will chirp the
same number of times as the events in memory. ( Maximum four events, four chirps)
NOTE: If the siren does not chirp, there are no events in memory. Step 3 - Press the Program Button once to view the last shut down code. The siren will chirp once to
confirm code one. Step 4 - The LED’s on the antenna will flash a code corresponding to a shut down trigger. Press the Program Button again to check the second code. The siren will chirp twice to confirm code two. Step 5 - To Clear Diagnostic Memory. While in Diagnostic Mode press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp once.
(If the siren does not chirp, there are no codes in memory).
2
NOTE: Once diagnostic memory has 4 improper shutdown events in memory, the system will not record any further shutdown events until the system memory has been cleared.
Installation Guide
WIRING DIAGRAM
(+) 30amp Output
(+) 30amp Output
(+) 30amp Input
(+) 30amp Input
(+) 30amp Output
(+) 30amp Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
Negative Input
Negative Input
Positive Input
Positive Input
Negative Input
(A/C) Input
(-) Input
Positive 15amp
Negative Input
Starter
Heater
Main Power
Main Power
Selectable P.5
Ignition 1
RE-ARM
STARTER DISABLE
FACTORY DISARM
TRUNK RELEASE
THIRD IGNITION (-)
(-) DOOR TRIGGER
HOOD PIN INPUT
(+) DOOR TRIGGER
BRAKE PEDAL
GROUND
TACH INPUT
GLOW PLUG
PARK LIGHTS
PARK BRAKE
Yellow
Green
Red
Red
White
Blue
YELLOW
ORANGE
BROWN
RED/WHITE
WHITE / VIOLET
GREEN
GREEN/WHITE
PURPLE
PINK
BLACK
BLUE/WHT
BLUE
WHITE
BLACK/WHITE
1
Jumper Access
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
(-)500ma Output
(-)500ma Output
Positive 3 amp
Negative Input
4th Ch. Programmable
Dome Light Supervision
Siren Output
Trunk Pin Switch Input
STARTER DISABLE. SEE PAGE. 7
TEMPERATURE SENSOR INPUT (OPTIONAL)
RF ANTENNA WITH DUAL LED’s & BUILT-IN VALET SWITCH
*Must be connected to operate the system
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)500ma Output
(-)Input
(-) Input
(-)500ma Output
(+)500ma Output
Door Lock
12V+ for Relays
Door Unlock
Passenger Door Unlock
Sensor Full-Warn
Sensor Pre-Warn
Sensor Ground
Sensor 12V+ Power
White / Green
Black
BLK/WHT
White / Blue
Red
BLK/WHT
Green
Red
Blue
Pink
Blue
Green
Black
Red
10
11
12
13
4 PIN BLUE
SIDE VIEW
4 PIN
RED
4 PIN
WHITE
SATELLITE LINK PLUG
(-)500ma Output
(-)500ma Output
(+) Input
Negative When Disarmed
Horn Honk/ 5th Channel
(+)Disconnect / Start trigger
Green
Pink
Blue
***500ma outputs are low current and are designed to activate relays
4 PIN
WHITE
4 PIN
WHITE
3
Installation Guide
INSTALLATION TIPS
Components
- Control module
- Remote transmitter(s)
- Antenna with built in Program Button and LED’s
- 6 pin main harness with dual 30amp power inputs
- 14 pin harness
- 4 pin square harness.
- 4 pin keyless entry harness
- 4 pin Aux. sensor harness
- Multi-tone Siren
- Hood pin safety switch
- Installation guide
- Owners manual
Recommended Pre-Installation Procedures
BEFORE STARTING INSTALLATION:
- Discuss the optional features with the customer.
- Take a few minutes to review the installation and owners manuals.
- Check if the vehicle has a factory security or anti-thieft system. *If equipped, inform the customer of addition parts and labour.
- Do a walk around the vehicle and check for any damage.
- If installing a LED discuss the placement with customer before installing.
Note: This remote starter is designed for fuel injected and diesel engines.
Recommended Installation Procedures
Proper Connections - Remote Starters can handle loads of up to 30 amps for extended periods of
time. It is CRITICAL to insure that ALL high current connections are properly soldered and insulated with quality electrical tape. Failing to insure proper connections will result in warranty being VOID and can result in a FIRE. The manufacturer is not responsible for any such damages. It only takes a few more minutes to do the job RIGHT.
Under Hood Connections - Route the hood pin and tach wires through the firewall into the engine compartment. Always try to pull the wires through a factory rubber grommet. If drilling through the
firewall, BE CAREFUL. Check for obstructions on both sides of the firewall. After drilling use a snap in grommet to protect the wires from sharp edges.
Installing the External Long Range Antenna - To insure the best possible reception, place the antenna in the center of the windshield, behind the rear view mirror. Before attaching to the glass ensure
that the surface is clean and dry. For best results with range, place the antenna below the tint screen. Run the cable under the head liner and behind the A-pillar panel. Be careful not to pinch the antenna cable. Plug the antenna into the BLUE connector on the Control Module. NOTE: This step is not used on Alarm Only Units with no External Antenna.
Mounting The Control Module - Never mount the module in the engine compartment. Select a location under the dash to install the main module. Be certain that the module is securely attached and
does not obstruct any serviceable areas. Do not force or jam the module into tight places instead of mounting. The module must be free from all moving parts such as brake, clutch and gas pedal linkages. Do not place the module directly in front of a heater vent.
Testing The System - When the installation is complete, it will be necessary to test that the system is working correctly. The system’s default programming will work on the majority of vehicles, but might
need to be adjusted for some applications. If the installation requires special timing or additional features, proceed to Program Mode.
ATTENTION: Hood Pin MUST always be connected!!
NOTE: Always inform user to place system in Service Mode before any service work is
4
performed on the vehicle.
Installation Guide
WIRING CONNECTORS
WIRING CONNECTORS
6 Pin Power Connector
Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory. Off during start. Red 12 power 30amp input Constant 12volt power at ignition harness. Red 12 power 30amp input Constant 12volt power at ignition harness. Blue Ignition 1 30amp output 12volts in ignition and start positions. White Selectable 30amp output Jumper Selectable. See Page 5.
14 Pin Connector
Yellow Re-Arm 0.75sec Pulse With Lock And On Shutdown. Orange (-) Output Negative While Locked - Brown Disarm 0.75sec Pulse With Unlock And Before Start. Red/White 3rd CH Trunk Release - Active When The Unlock Button Is Held For 3seconds. White/Violet (-)Running Negative Output While Running. Green (-) Door Negative Door Trigger Input - Purple (+) Door Positive Door Trigger Input - Manual Trans And Alarm Units Only. Green/White Hood Pin Negative Hood Pin Input - MUST BE CONNECTED!! Pink Brake Positive Brake Input - MUST BE CONNECTED!! Black Ground System Ground Input - MUST BE CONNECTED!! Blue/White Tach Tach Signal Input - MUST BE CONNECTED!! Blue Glow Plug Negative Glow Plug Input - DIESEL ENGINE ONLY. **Starter Program Mode. White Park Lights Positive Park light Output - 10 Amp Max. Black/White Park Brake Negative Park Brake Input - Manual Transmission Models Only.
**Starter Program Mode.
Manual Trans And Alarm Units Only.
4 Pin Connector Square
White/Green Channel 4 Programmable- See Alarm Settings. Menu 2. Black Dome Light Negative Output For Dome Light Supervision. White/Blue Siren Positive Output For Siren. Red Trunk Pin Negative Input for Trunk Pin.
4 Pin Connector Red
Green Door Lock Door Lock Output - Programmable - Menu 1 Setting 3. Red 12 Volts Low Current Output. Use With Voltage Inverter Blue Door Unlock Door Unlock Output - Programmable - Menu 1 Setting 3. Pink 2nd Unlock Door Unlock Output - Programmable - Menu 1 Setting 3.
3 Pin Connector White
Green (-) Disarmed Negative Output When The System Is Disarmed. Pink Horn/5th Channel Programmable Output. Blue (+) Disconnect (+) Disconnect Or Instant Start Trigger.
Jumper Selections
The jumpers control the output on the white wire from the six pin harness. Place the jumpers in the above order to change the output.
Note: The default setting is second ignition.
Output on White wire Jumper position
Second Starter Position 1 Second Accessory Position 2
Second Ignition Position 3
Back View Of Module
Jumpers
3 2 1
5
5
Loading...
+ 11 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use