Ultrak HEB10, HEB12 Installation Instructions Manual

HEB Serie

s

10- AND 12-INCH
CAMERA
ENCLOSURES
WITH OPTIONAL
SUNSHIELD,
HEATER AND
BLOWER KITS
AND MOUNTING
BRACKET

INSTALLATION
INSTRUCTIONS

Worldwide Support Center
1301 Waters Ridge Drive



Lewisville, TX 75057

[phone]



[phone]  FAX [phone]

ii

ISSUE 1 - November 1996

1996 BY ULTRAK

ALL RIGHTS RESERVED

PRINTED IN KOREA

ULTRAK

1301 WATERS RIDGE DRIVE

LEWISVILLE, TX 75057

[phone]

ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED
BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM ULTRAK.

THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL
RESPECTS. HOWEVER, ULTRAK CANNOT ASSUME RESPONSIBILITY FOR ANY
CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION
CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR
NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH
CHANGES.

iii

TABLE OF CONTENTS

Paragraph Title

Page

SECTION 1. HEB CAMERA HOUSING SERIES INTRODUCTION

1.1 PURPOSE ....................................................................................1

1.2 FEATURES...................................................................................1

SECTION 2. HOUSING INSTALLATION INSTRUCTIONS

2.1 HEB10-BK BLOWER KIT INSTALLATION ..................................2

2.2 HEB10-HK/HEB12-HK HEATER KIT INSTALLATION.................4

2.3 HEB10-BK BLOWER KIT WITH HEB10-HK/HEB12-HK

HEATER KIT INSTALLATION ..................................................6

2.4 CAMERA MOUNTING FOR HEB SERIES HOUSINGS ..............8

2.5 HEB10-SS/HEB12-SS SUNSHIELD INSTALLATION................10

2.6 UL-WBM & UL-WB+BJ WALL BRACKET MOUNTING.............11

SECTION 3. SPECIFICATIONS

3.1 HEB HOUSING SPECIFICATIONS ...........................................12

3.2 HEB10-BK BLOWER SPECIFICATIONS ..................................13

3.3 HEB10-HK/HEB12-HK HEATER SPECIFICATIONS.................13

3.4 HEB10-SS/HEB12-SS SUNSHIELD SPECIFICATIONS ...........13

3.5 UL-WBM & UL-WB+BJ WALL MOUNT SPECIFICATIONS ......14

1

SECTION 1

HEB CAMERA HOUSING SERIES INTRODUCTION

1.1 PURPOSE

The HEB10 and HEB12 camera housing series are stylishly and
functionally designed enclosures for 1/3” and 1/2” cameras with
fixed focal length or standard zoom lenses. This manual
describes how to assemble the housing and its optional
components, affix the camera, and mount the assembly to a
suitable surface.

1.2 FEATURES

The HEB10 and HEB12 camera housing series feature:

• Contemporary design

• Die-cast and extruded aluminum construction

• Adjustable mounting track

• Hinged/removable body for easy servicing

• Compression cable fittings

• Optional heater kit, blower kit and snap-on sunshield

components

• Indoor/outdoor applications

• Epoxy powder coating for corrosion resistance

• Dustproof, IP65 weatherproofing

• Low Cost

• Preassembled models:

1. HEB10 & HEB12.................. housing

2. HEB10-01 & HEB12-01 ....... housing with sunshield

3. HEB10-02 & HEB12-02 ....... housing with sunshield

and heater kit

4. HEB10-03 & HEB12-03 ....... housing with sunshield,

heater kit and blower kit

2

SECTION 2

HOUSING INSTALLATION INSTRUCTIONS

2.1 HEB10-BK BLOWER KIT INSTALLATION (without heater)

This section contains comprehensive instructions for installing
the blower kit into the HEB10, HEB10-01, HEB12 and HEB12-01
camera housing. The HEB10-BK is compatible in both the
HEB10 and HEB12 series. If you are also installing the heater,
please skip to page 5 for comprehensive instructions. The blower
kit is available in a preassembled package with a housing, heater
kit, and sunshield under model HEB10-03 or HEB12-03.

1. If applicable, slide the sunshield off the main housing unit.

2. Remove the two Phillips panhead screws located midway up
the rear of the housing. Retain the screws and their black
rubber gaskets, which were left in the holes on the rear of the
housing. (See Figure 1)

3. By sliding the housing shell away from the rear portion of the
unit, separate the housing into two sections. Be careful not to
disconnect the end of the ground cable that is attached to the
housing shell. (See Figure 1)

4. Locate the following parts that are taped to or enclosed in the
housing: two black plastic elevation plates, a nylon washer,
and three hexagonal screws of varying lengths for camera
mounting. Set these parts aside for later use.

5. Remove the standard silver camera mounting plate by
unscrewing the two flathead screws located at the rear.
Retain the screws. (See Figure 1)

FIGURE 1

3

6. Remove the rear of the housing from the base by unscrewing
the two Phillips panhead screws. (See Figure 1)

7. Use these screws to replace the rear with the blower unit,
being careful not to damage the wiring to the attached circuit
board. (See Figure 2)

8. Reattach the standard silver camera mounting plate to the
shelf extending from the rear of the housing. Align the holes
and secure using the two flathead screws mentioned in step

5. (See Figure 2)

9. Next, mount the blower circuit board on the camera mounting
plate. To do this, first place the two plastic spacers on the
two holes near the rear of the plate. Set the blower circuit
board on top of the spacers, aligning the holes and keeping
the wiring on the same side. Insert the small Phillips panhead
screws and secure the assembly. (See Figure 2)

10. Connect the
external power
supply (not
included) to the
circuit board. The
recommended
power supply is 24
Vac, 50 VA. (See

Figure 3)

11. To mount your camera, consult the section Camera
Mounting for HEB Series Housings on page 7. Begin with
step 5. Then see UL-WB+BJ & UL-WBM Wall Bracket
Mounting on page 10.

FIGURE 2

FIGURE 3

4

2.2 HEB10-HK/HEB12-HK HEATER KIT INSTALLATION

(without blower)

This section contains instructions for installing the heater kit for
the HEB10, HEB10-01, HEB12 and HEB12-01 camera housings.
If you are also installing the blower unit, please skip to page 5 for
comprehensive instructions.

While this heater kit is sold as an add-on component for the
HEB10, HEB10-01, HEB12 and HEB12-01, it is also available in
a preassembled package. The HEB10-02 and HEB12-02 are 10­and 12-inch camera housings respectively with an installed
sunshield and heater. The HEB10-03 and HEB12-03 add a
blower kit to this package.

1. If applicable, remove the sunshield by sliding it off the main
housing unit.

2. Loosen the two Phillips panhead screws located midway up
the rear of the housing. Leave the screws intact in the rear
portion of the housing. (See Figure 4)

3. By sliding the housing shell away from the rear portion of the
unit, separate the housing into two sections. Be careful not to
disconnect the end of the ground cable that is attached to the
housing shell. (See Figure 4)

4. Locate the following parts that are taped to or enclosed in the
housing: two black plastic elevation plates, a nylon washer,
and three hexagonal screws of varying lengths for camera
mounting. Set these parts aside for later use.

FIGURE 4

5

5. Remove the standard silver mounting plate by unscrewing
the two flathead screws located at the rear. Then replace
this unit with the optional mounting plate with built-in heater.
Make sure that the heater plate is secured to the shelf that
extends from the rear of the housing unit. (See Figures 4 &

5)

6. Connect the external
power supply (not
included) to the circuit
board. The
recommended power
supply is 24 Vac, 50 VA.

(See Figure 6)

7. To mount your camera,
consult the section
Camera Mounting for
HEB Series Housings on
page 8. Begin with step

5. Then see UL-WB+BJ
& UL-WBM Wall Bracket
Mounting on page 10.

FIGURE 5

FIGURE 6

6

2.3 HEB10-BK BLOWER KIT WITH HEB10-HK/HEB12-HK
HEATER KIT INSTALLATION

This section contains instructions for installing the heater kit and
blower kit for HEB10, HEB10-01, HEB12 and HEB12-01 camera
housings. While these kits are sold as add-on components, they
are also available in a preassembled package. The HEB10-03
and HEB12-03 are 10- and 12-inch camera housings respectively
with an installed sunshield, heater and blower.

1. If applicable, remove the sunshield by sliding it off of the

main housing unit.

2. Remove the two Phillips panhead screws located midway up

the rear of the housing. Retain the screws and their black
rubber gaskets, which were left in the holes on the rear of the
housing. (See Figure 7)

3. By sliding the housing shell away from the rear portion of the

unit, separate the housing into two sections. Be careful not to
disconnect the end of the ground cable that is attached to the
housing shell. (See Figure 7)

4. Locate the following parts that are taped to or enclosed in the

housing: two black plastic elevation plates, a nylon washer,
and three hexagonal screws of varying lengths for camera
mounting. Set these parts aside for later use.

5. Remove the standard silver camera mounting plate by

unscrewing the two flathead screws located at the rear.
Retain the screws. (See Figure 7)

6. Remove the rear of the housing from the base by unscrewing

the two Phillips panhead screws. (See Figure 7)

FIGURE 7

7

7. Use these screws to

replace the rear with
the blower unit,
being careful not to
damage the wiring
to the attached
circuit board. (See

Figure 8)

8. Attach the mounting plate with heater unit to the shelf

extending from the rear of the housing. Align the holes and
secure using the Phillips panhead screws mentioned in step

5. (See Figure 8)

9. Using a small screwdriver, disconnect the wiring to the N and

L1 ports on the heater circuit board. (See Figure 8)

10. Next, replace the heater circuit board with the circuit board

that is wired to the blower. To do this, locate the two Phillips
panhead screws on the heater circuit board. Unscrew them
and remove the board from the mounting plate. With the two
plastic spacers already over the small holes on the mounting
plate, set the blower circuit board on top of the spacers,
keeping the wiring on the same side. Align the holes in the
board with the spacers and insert the small Phillips panhead
screws. Secure the assembly. (See Figure 8)

11. Connect the heater

wiring harness to the
blower circuit board
as shown. Then
connect the external
power supply (not
included) to the
circuit board. The
recommended power
supply is 24 Vac, 50
VA. (See Figure 9)

12. To mount your camera, consult the next section, Camera

Mounting for HEB Series Housings on page 8. Begin with
step 5. Then see UL-WBM & UL-WB+BJWall Bracket
Mounting on page 10.

FIGURE 8

FIGURE 9

8

2.4 CAMERA MOUNTING FOR HEB SERIES HOUSINGS

This section contains comprehensive instructions for installing a
camera into any of the HEB series housings. If you are installing
optional equipment, such as a heater/blower kit, please consult
the previous section in this manual that is appropriate and refer
to this section when instructed to do so.

1. If applicable, remove the sunshield by sliding it off the main

housing unit.

2. Loosen the two Phillips panhead screws located midway up

the rear of the housing. Leave the screws intact in the rear
portion of the housing. (See Figure 10)

3. By sliding the housing shell away from the rear portion of the

unit, separate the housing into two sections. Be careful not to
disconnect the end of the ground cable that is attached to the
housing shell. (See Figure 10)

4. Locate the following parts that are taped to or enclosed in

the housing: two black plastic elevation plates, a nylon
washer, and three hexagonal screws of varying lengths for
camera mounting. Set these parts aside for later use.

FIGURE 10

FIGURE 11

9

5. To install your camera on the mounting plate with heater,

use the supplied 1/4” flathead screws and nylon washer.

(See Figure 11)

NOTE: If you are using a camera with a zoom lens, it may be

necessary to use one or both of the provided black elevation
plates to keep the camera stable. With one or both elevation
plates under the camera, insert one of the longer screws
through the bottom of the camera mounting plate, through
the elevation plate(s) and into the camera. Use the 1/4”
screw to secure the lens. (See Figure 12)

6. Insert the cable through the compression glands, and make

all of the necessary electrical connections as described in
the instructions that accompanied the camera. Be sure that
the compression glands are firmly fixed. (See Figure 11)

7. Reassemble the

housing unit by sliding
the body of the housing
completely across the
base, being careful not
to disrupt any electrical
connections. Secure the
assembly by tightening
the two screws through the rear of the housing into the
housing body. (If you installed a blower unit into the
assembly, remember to slide the small black rubber gaskets
over the tips of the screws.) (See Figure 13)

8. If applicable, reinstall the sunshield by sliding the sunshield

onto the housing unit.

FIGURE 13

FIGURE 12

10

2.5 HEB10-SS/HEB12-SS SUNSHIELD INSTALLATION

This section contains instructions for installing the sunshield for
the HEB series housing. While this is sold as an add-on
component for the HEB10 and HEB12, it is also available in a
preassembled package. The HEB10-01 and HEB12-01 include a
housing and a sunshield. The HEB10-02 and HEB12-02 include
a housing, sunshield and heater. The HEB10-03 and HEB12-03
include a housing, sunshield, heater and blower.

1. After the camera has been installed and the housing has

been reassembled (See Camera Mounting for HEB Series
Housings on page 7), install the sunshield by sliding it along
the top of the housing unit. (See Figure 14)

2. To mount the completed assembly, consult the next section,

UL-WB+BJ & UL-WBM Wall Bracket Mounting.

2.6 UL-WBM & UL-WB+BJ WALL BRACKET MOUNTING

This section contains information for mounting the recommended
UL-WBM wall bracket, which is sold separately from HEB series
camera housings (The UL-WB+BJ is also compatible). Be sure
that the camera and the optional components have been
installed into the housing properly before proceeding to mount
the assembly.

FIGURE 14

11

1. Using fasteners of appropriate size and type, attach the

bracket to the wall surface in a position that will allow for
viewing of the selected area. (See Figure 15)

2. Locate two nuts that freely slide along the channel. Position

the nuts approximately 2-3/8” from one another. (See Figure

15)

3. Place the housing onto the mount, aligning the holes. Insert

the two provided bolts through the mount and into the nuts.
Secure the assembly. (See Figure 15)

4. Adjust the movable arm of the wall bracket to attain the

desired position. Once it is in place, tighten the bolt located at
the pivot point of the movable arm.(See Figure 15)

FIGURE 15

12

SECTION 3

SPECIFICATIONS

3.1 HEB HOUSING SPECIFICATIONS

Dimensions (WxHxL):

HEB10 5.5 x 5.0 x 10.23 in

(139 x 128 x 260 mm)

HEB12 5.5 x 5.0 x 12.6 in

(139 x 128 x 320 mm)

Weight:

HEB10 4.5 lbs. (2.0 kg)
HEB12 5.0 lbs. (2.3 kg)

Maximum Camera Size(WxHxL): Accommodates Camera/Lens

Combinations (Including BNC)
up to:

HEB10 3.5 x 3.3 x 10 in

(88.9 x 83.8 x 254 mm)

HEB10 with heater/blower 3.5 x 3.3 x 9 in

(88.9 x 83.8 x 229 mm)

HEB12 3.5 x 3.3 x 12 in

(88.9 x 83.8 x 305 mm)

HEB12 with heater/blower 3.5 x 3.3 x 11 in

(88.9 x 83.8 x 279 mm)

Viewing Area (WxH) 3.5 x 3.1 in

(88.9 x 78.7 mm)

Viewing Window Clear 1/8-in Double Density

Glass
Camera Mounting Slotted Camera Sled
Cable Entry 2 Compression Fittings
Construction Extruded and Die-cast

Aluminum
Finish Almond Color Epoxy Powder

Coating
Options:

HEB10-SS Snap-on Sunshield for HEB10
HEB12-SS Snap-on Sunshield for HEB12
HEB10-HK Heater Kit for HEB10
HEB12-HK Heater Kit for HEB12

13

HEB10-BK Blower Kit for HEB10

and HEB12
Environment Indoor/Outdoor
Recommended Mounts UL-WB+BJ & UL-WBM

Operating Temperature -20

o

C (-4 oF) to 60 oC (140 oF)

3.2 HEB10-BK BLOWER SPECIFICATIONS

Power Supply 24Vac
Power Consumption 3.4W

Blower ON t

o

C > 35oC +/- 3oC

t

o

F > 95oF +/- 5oF

Blower OFF t

o

C < 20oC +/- 3oC

t

o

F < 68oF +/- 5oF

Dimensions (WxHxD): 5.5 x 5.0 x 3.7 in

(139 x 128 x 97 mm)

3.3 HEB10-HK & HEB12-HK HEATER SPECIFICATIONS

Power Supply 24Vac
Power Consumption 40W

Heater ON t

o

C < 14oC +/- 3oC

t

o

F < 39oF +/- 5oF

Heater OFF t

o

C > 20oC +/- 3oC

t

o

F > 68oF +/- 5oF

3.4 HEB10-SS & HEB12-SS SUNSHIELD SPECIFICATIONS

Dimensions (WxHxL):

HEB10-SS 5.7 x 3.4 x 15.7 in.

(144 x 90 x 400 mm)

HEB12-SS 5.7 x 3.4 x 19.7 in.

(144 x 90 x 500 mm)
Weight:

HEB10-SS 2.1 lbs. (1.0 kg)
HEB12-SS 2.5 lbs. (1.1 kg)

14

3.5 UL-WBM & UL-WB+BJ WALL MOUNT SPECIFICATIONS

Dimensions (WxHxL):

UL-WBM 2.8 x 4.5 x 8.9 in.

(70 x 115 x 226 mm)

UL-WB+BJ 2.8 x 4.5 x 11.2 in.

(70 x 115 x 284 mm)
Weight:

UL-WBM 1.1 lbs. (0.5 kg)
UL-WB+BJ 1.4 lbs. (0.6 kg)

Pan Adjustment 360

o

Tilt Adjustment 70

o

Locking Method Friction Controlled through Bolt

Tightening
Wall Mounting Method 4 Holes for Fasteners of a

Suitable Size and Type. Mount

to a Secure Solid Surface.
Enclosure Mounting:

UL-WBM 2 Allen Bolts
UL-WB+BJ 2 HEX Bolts

Maximum Load:

UL-WBM 35.0 lbs. (15.9 kg)

UL-WB+BJ 55.0 lbs. (25.0 kg)
Construction Extruded & Die-cast Aluminum
Finish Epoxy Powder Coating
Environment Indoor/Outdoor
Optional Components:

CP Reinforcing Support Plate

CW Corner-mount Adapter

SFP Pole-mount Adapter

15

THIS PAGE INTENTIONALLY LEFT BLANK

16

THIS PAGE INTENTIONALLY LEFT BLANK

17

FORM 1047, REV. 11/96