Page 1
Z Collection
Two Handle Roman Tub Faucet with
hand-shower and Rough-in Valve
Installation/Installation/Instalación
CUSTOMER SERVICE
TOLL-FREE 1-888-OK-ULTRA (658-5872)
UF65440 - Polished Chrome
UF65443 - PVD Brushed Nickel
UF65445 - Oil Rubbed Bronze
UF65447 - Matte Black
Tools You Will Need / Outils dont vous aurez besoin / Herramientas necesarias
Adjustable Wrench
Clé à molette
Llave ajustable
Cinta selladora para rosca
Pipe Tape
Ruban pour tuyau
Phillips Screwdriver
Tournevis cruciforme
Destornillador cruciforme
Groove join pliers
Pince multiprise
Pinzas ajustables
SAFETY TIPS
• If you use soldering for the installation of the faucet, the seats, cartridges and washers will have to be removed
before using flame. Otherwise, warranty will be void on those parts.
• Cover your drain to avoid losing parts.
• 0℃~55℃.
CONSIGNES DE SÉCURITÉ
• Si vous posez le robinet par brasage, il est essentiel de retirer les sièges, les cartouches et les rondelles avant
d’appliquer la flamme, faute de quoi la garantie sur ces pièces sera annulée.
• Couvrez le drain pour ne pas perdre des pièces.
• 0℃~55℃.
CONSEJOS DE SEGURIDAD
• En el caso de utilizar soldadura para instalar el grifo, remueva los asientos, cartuchos y arandelas antes de usar la
llama. De lo contrario, se anulará la garantía para esos componentes.
• Tape la boca del desagüe para prevenir la pérdida de piezas pequeñas.
• 0℃~55℃.
Revised 4-2020
Page 2
Installation/Installation/Instalación
UF65440
UF65443
UF65445
UF65447
1
1
Remove the mud guard from the
spout nipple-diverter assembly and
unthread the diverter assembly.
4
2
2
3
Slide the spout nipple down into the
spout hole and secure by threading
on the washer and nut.
5
3
Re-attach the diverter assembly to
the spout nipple.
6
Remove the mud guards from the
hot and cold valves.
7
Teflon Tape
Apply teflon tape to the bottom outlet
on the spout nipple-diverter assembly
and attach the rough hand shower
hose with washer.
Push the hot and cold valves up from
the bottom and thread on the valve
nuts from the top to secure the valves.
8
Remove the mud guard from the
hand shower hose guide nipple and
unthread the fixed assembly.
Teflon Tape
Apply teflon tape to the connector
and attach hoses. If you have set the
hot and cold valves more than 12”
from the spout nipple-diverter
assembly, please supply a code
approved supply line.
9
1
Slide the hand shower hose guide
nipple into the appropriate hole and
secure by threading on the nut and
washer. For optimum hand shower
usage, it should be located no father
than 24" from the spout.
Revised 4-2020
Page 3
Replacement Parts / Pièces de rechange / Repuestos
Part No.DescriptionNO.
1
Diverter Knob & Rod Asse
2
Deck Spout Set Screw & Allen Key
3
4
Handle Adaptor 9Q224700PL
Handle Base Assembly 9Q224800CP/AP/HA/HBW
5
Base Assembly 9Q224900CP/AP/HA/HBW
6
Aerator 5E0M0115PL
7
8
Base Assembly
9
Shower Base Assembly
10
11
Hand Shower Set Screw & Allen Key 9Q1349NT
12
Hot Valve Body Assembly 9Q225300NT
13
Spout Diverter Assembly 9Q225500NT
14
Cold Valve Body Assembly 9Q225400NT
mbly
9Q225000CP/AP/HA/HBW
9Q1350NT
5C0001500CP/AP/HA/HBW0Handle
9Q225200CP/AP/HA/HBW
9Q225100CP/AP/HA/HBW
5F0001400CP/AP/HA0Hand Shower
1
2
3
4
5
10
11
UF65440
UF65443
UF65445
UF65447
10
12
11
3
Teflon Tape
9
8
7
6
Slide the black nylon or finished hand
shower hose into the hand shower
hose guide nipple and attach to rough
hand shower hose using teflon tape.
For optimum hand shower usage it
should be located no father than 24"
from the spout.
Connect valve body to water supplies
using the proper fittings.
12
Turn on water supply and check for
leaks.
15
Hose 5G0M0191CP
16
Hose 5G0M0055CP
17
Diverter Assembly
51014144NC
12
13
14
15
16
17
13
Replace mud guards.
14
Installation completed.
Limited Lifetime Warranty
Ultra Faucets warrants to the original purchaser that its products will be free from defects in workmanship and materials. All Ultra
Faucets are provided with a life time limited warranty. This warranty does not cover any other labor or service charges associated with
the removal, repair, or reinstallation of Ultra Faucets products. This express warranty does not apply to products that have been
damaged as a result of misuse, abuse, negligence, accident, faulty installation or maintenance practices and/or used in any manner
contrary to those recommended by the manufacturer.
Need help? Please ca
Besoin d’aide? Veuillez communiquer avec notre service à la clientèle au numéro gratuit 1-888-658-5872 pour tous renseignements
ou services complémentaires.
¿Requiere asistencia? Llame a nuestro Servicio al Cliente, sin costo, al 1-888-658-5872 para asistencia adicional o servicio.
ll our toll-free customer service line at 1-888-658-5872 for additional assistance or service.
Revised 4-2020
Revised 4-2020
Page 4
Installation/Installation/Instalación
UF65440
UF65443
UF65445
UF65447
15
Turn the water supply off and remove
the mud guards.
18
16
Place the spout washer under the
spout and install spout on spout
nipple-diverter assembly. Be sure the
spout is firmly resting on the deck.
Secure the spout with the setscrew.
17
Insert diverter knob and rod assembly
into the spout and thread the
assembly onto the diverter rod in the
spout diverter assembly. Pull the
diverter rod and knob up and down to
test the connection.
19 20
24
Leaving the water on, pull the hose to
its farthest extension and point it into
the tub. Pull the diverter knob to its
top position. Flush the debris for one
minute. Turn off the valves.
27
25
Attach the hand shower to the black
nylon or finished hose.
26
Re-install the aerator with tool.
Insert the bush and screw into the
hot valve.
turning the
for cold valve.
Secure
screw
the assembly
clockwise. Repeat
by
21
Pull black nylon or finished hose
through the hand shower nipple
bracket. Slide the hand shower
washer, bracket and hose guide over
the hose. Secure the assembly with
the setscrew. Note, make sure the
hose does not slip under the deck.
Place the washer over the hot valve.
Align the handle and place the
handle and escutcheon assembly into
the valve. Secure the assembly by
turning the escutcheon clockwise.
Repeat for cold valve.
22
Remove the aerator with tool. Turn
the water supply on.
Remove the plastic cover.
23
Make sure the diverter knob is in the
down position. Turn the faucet
handles on full for one minute to flush
debris.
Installation complete.
Revised 4-2020
Revised 4-2020
Loading...