Installation Guide
2075DWRWC —
Drawer Model Wine Captain
™
®
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696
www.U-LineService.com
OnlineService@U-Line.com
©2005 U-Line Corporation
02/2005
2075DWRWC — Drawer Model Wine Captain
®
™
Contents
Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Clearances Information . . . . . . . . . . . . . . . . . . . . . . . . . 5
Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . 6
Adding a Final Finish Coat to Wood Trim . . . . . . . . . . 7
Staining Wood Trim a Different Color . . . . . . . . . . . . . 7
Checking Drawer Alignment . . . . . . . . . . . . . . . . . . . . 8
Adjusting Drawer Alignment . . . . . . . . . . . . . . . . . . . . 8
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 11
Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation of the 2075DWRWC . . . . . . . . . . . . . . . . . . 12
Anti-Tip Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . . 13
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 14
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1 Follow Safety Precautions
IMPORTANT
PLEASE READ all instructions completely before
attempting to install or operate the unit.
• This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician in accordance with applicable
electrical codes.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
DANGER
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury,
or death.
CAUTION
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
www.U-LineService.com 2 02/2005
™
2075DWRWC — Drawer Model Wine Captain
®
General Precautions
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Keep the unit unplugged throughout installation
except during testing.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Never use an extension cord to connect power to
the unit.
• Always keep your working area dry.
WARNING
The Anti-Tip Kit must be installed on this unit
before it is used. Never use the drawers as steps
or as a shelf to support more than the drawers’
contents. Serious personal injury could occur.
CAUTION
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp edges.
• Do not lift the unit by the drawer handle.
• Do not install the unit behind closed doors or in any
way that would obstruct airflow to the front grille,
which may cause the unit to malfunction.
2 Inspect and Plan
You have received a carton containing your 2075DWRWC
Drawer Model Wine Captain
containing a User Manual, a Product Registration
Card and Anti-Tip Kit. Complete and mail the
Product Registration Card or register online at
www.U-LineService.com. Once your unit is installed,
keep the User Manual and this Installation Guide in
a safe place for future reference.
Your unit is Black or Stainless Steel. Black units have
drawers with black glass fronts, sculpted handles and
black vinyl-clad cabinets. Stainless Steel units have
drawers with stainless steel framed fronts, sculpted
stainless steel handles and black vinyl-clad cabinets. All
units come with maple trim wine racks and caddy that can
be finished or stained. Please carefully follow the
directions that apply to your unit and your intended
design.
Tools/Materials Required
• Wrenches
• Screwdrivers — slotted and Phillips head
• Sandpaper; low odor, water clean up, quick drying
finish; tack cloth and, if desired, water-based wood
stain and synthetic foam brush
Inspection
Unwrap and inspect the unit on a flat, level surface
capable of supporting its entire weight.
Removing Protective Coating
®
with a package inside
Stainless Steel Models:
When inspecting/installing a Stainless Steel unit, the
protective coating covering the drawer fronts must be
removed. Start at a corner of the drawers and pull back
the protective coating to remove it from the drawer
fronts.
After all the protective coating has been removed from
the drawers, clean all Stainless Steel surfaces with Claire
Stainless Steel Polish and Cleaner or comparable product
or a mild detergent and warm water solution and soft
cloth. Do NOT use abrasive cleaning agents.
Note: If cleaning with mild detergent and warm water
solution and soft cloth, the unit MUST be treated with
Claire Stainless Steel Polish and Cleaner or comparable
product to prevent discoloration.
Clean all glass surfaces with a non-chlorine glass cleaner.
02/2005 3 www.U-LineService.com
2075DWRWC — Drawer Model Wine Captain
®
™
Exterior Cleaning
(As Required)
Black Models:
• Clean glass drawer fronts with glass cleaner. The
drawers, grille and cabinet may be cleaned with a mild
detergent and warm water solution. Do not use
solvent-based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
Stainless Steel Models:
• Stainless steel models can discolor when exposed to
chlorine gas, pool chemicals, salt water or cleaners with
bleach.
• Clean glass drawer fronts with a non-chlorine glass
cleaner. Keep your stainless steel surfaces looking new
by cleaning with a good quality all-in-one stainless
steel cleaner/polish on a monthly basis. For best results
use Claire Stainless Steel Polish and Cleaner, which can
be purchased from U-Line Corporation. (The part
number is 173348.) Comparable products are
acceptable. Frequent cleaning will remove surface
contamination that could lead to rust. Some
installations may require cleaning on a weekly basis.
• Do not clean with steel wool pads.
• Do not use stainless steel cleaners/polishes on
the glass surfaces.
• Do not use cleaners that are not specifically
intended for stainless steel on stainless steel
surfaces (this includes glass, tile and counter
cleaners).
• If any surface discolors or rusting appears, clean it
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Use of abrasive pads such as Scotchbrite will
cause the graining in the stainless to become
blurred.
• Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
3 Prepare Site
Your U-Line product has been designed for built-in
installation. Your unit does not require additional air
space for top, sides or rear. However, the front grille must
NOT be obstructed and clearance is required for electrical
connection in the rear.
Note: Unit can NOT be installed behind a closed cabinet
door.
Cut-Out Dimensions
See Electrical
Specifications
for Power Supply
34-1/4"
to
35-1/8"
24-3/16"
Figure 1
Follow the cut-out drawing in Figure 1. The 24-3/16"
width allows 1/4" for ease in installation and removal of
the unit. 24" is the counter depth in most installations.
The unit is 23-11/16" deep including the drawer and not
the full handle (see Figure 2).
23-11/16"
www.U-LineService.com 4 02/2005
™
2075DWRWC — Drawer Model Wine Captain
®
Product Dimensions
25-13/16"
Including
Handle
34-1/8"
23-15/16"
Black or Stainless Steel
Figure 2
Please note that the unit has adjustable feet that can add
one additional inch to height during leveling or to match
adjacent cabinets (see Figure 19 on Page 11).
Clearances Information
The unit must be installed in a wall or under a countertop to allow for the installation of the Anti-Tip Kit (see
Page 12).
WARNING
The Anti-Tip Kit must be installed on this unit
before it is used. Never use the drawers as steps
or as a shelf to support more than the drawers’
contents. Serious personal injury could occur.
The unit is designed so it can be installed next to a wall on
either side (see Figure 3).
Figure 3
Cabinet
or Wall
02/2005 5 www.U-LineService.com
2075DWRWC — Drawer Model Wine Captain
®
™
The drawer unit can be installed with an appliance or
fixture located in front of it, as long as there is adequate
clearance for the drawer to be opened and removed
when servicing (see Figure 4).
Note: U-Line recommends you consider additional
clearance in front of the open drawer for convenience.
24" Min.
Other Site Requirements
Power Supply
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A circuit (normal household current). See
Electrical Specifications on Page 11.
Environmental Requirements
The surrounding air temperature must be at least 50°F
(10°C) but must not exceed 110°F (40°C). Units may be
installed outdoors in a covered area. The unit must not be
located near heat-generating equipment or in direct
sunlight.
Figure 4
www.U-LineService.com 6 02/2005
™
2075DWRWC — Drawer Model Wine Captain
®
4 Prepare Racks and Caddy
The U-Line Wine Captain® is equipped with woodtrimmed wine racks that are coated at the factory with a
clear vinyl sealer, which will adequately protect the wood
in normal usage. A final finish coat was not applied so
that the wood trim could be stained to match décor. The
trim on the racks may be coated with a final finish or
stained.
If neither of these treatments are to be included in this
installation, go on to 5 Adjust Drawers.
CAUTION
To prevent permanent damage to the inner liner of the
Wine Captain
removed from the unit for staining and/or finishing.
Allow stain/finish to dry thoroughly (at least 24 hours per
coat) in accordance with the stain/finish manufacturer’s
instructions prior to re-installing the wood trim inside the
cabinet of the Wine Captain
the inner liner of the unit to have a permanent odor,
which is not covered by the warranty.
®
, the wine rack wood trim MUST be
®
. Failure to do so may cause
Adding a Final Finish Coat to Wood
Trim
IMPORTANT
Do not remove the two racks attached at the drawer
slides.
1. Remove wine caddy, the
top two racks in the upper
drawer and the top rack
in the bottom drawer
(remove each wine rack
by sliding it out and up).
See Figure 5.
2. Remove and save screws
securing wood trim to the
racks and caddy.
3. Remove and save screws
securing wood trim to the
two racks attached at the drawer slides (without
removing these racks themselves).
4. Lightly scruff sand the wood trim with 280 grit 3M
Tri-M-Ite sandpaper.
5. Remove sanding dust with a tack cloth.
6. Apply a thin coat of Minwax Polycrylic, following
container label for directions. Allow to dry 24 hours.
Slide Out
and Up
Figure 5
7. Lightly sand, tack and reapply 2 times, if desired.
8. Allow the final coat to dry for 24 hours.
9. Reinstall wood trim to wine racks and caddy using
screws removed in Steps 2 and 3.
10. Reinstall the removed wine racks and caddy in unit.
11. Go on to 5 Adjust Drawers.
Staining Wood Trim a Different
Color
IMPORTANT
Do not remove the two racks attached at the drawer
slides.
1. Remove wine caddy, the top two racks in the upper
drawer and the top rack in the bottom drawer
(remove each wine rack by sliding it out and up). See
Figure 5.
2. Remove and save screws securing wood trim to the
racks and caddy.
3. Remove and save screws securing wood trim to the
two racks attached at the drawer slides (without
removing these racks themselves).
4. Apply Minwax Water-Based Wood Stain to wood with a
synthetic foam brush. Stain must penetrate
approximately 3 minutes. After this period, while stain
is still wet, take a stain-dampened rag and remove all
excess stain. Wipe in the direction of the grain with
medium pressure to achieve the desired stain color.
5. After 2 hours, repeat Step 4.
6. Allow stain to dry for a minimum of 3 hours before
finishing.
7. Sand the wood with very fine sandpaper to smooth the
surface from the staining process.
8. Remove sanding dust with a tack cloth.
9. Apply a thin coat of Minwax Polycrylic, following
container label for directions. Allow to dry 24 hours.
10. Lightly sand, tack and reapply 2 times, if desired.
11. Allow the final coat to dry for 24 hours.
12. Reinstall wood trim to wine racks and caddy using
screws removed in Steps 2 and 3.
13. Reinstall the removed wine racks and caddy in unit.
14. Go on to
5 Adjust Drawers
.
02/2005 7 www.U-LineService.com
2075DWRWC — Drawer Model Wine Captain
®
™
5 Adjust Drawers
Checking Drawer Alignment
The unit’s drawers are aligned at the factory before
shipment. However, their alignment could have been
disturbed during shipment.
Aligned
Front-to-Back
Aligned
Side-to-Side
Adjusting Drawer Alignment
WARNING
SHOCK HAZARD — The unit must be unplugged
from the wall outlet during drawer removal,
adjustment and re-installation.
Drawer Removal
1. Confirm that the unit is
unplugged from wall
outlet.
2. Unplug the drawer’s
connection wiring (top
drawer only).
3. Remove the mounting
screws. See
4. Pull the drawer
completely out of the
unit.
Figure 7
.
Mounting
Screw
Figure 7
Aligned
Top-to-Bottom
Figure 6
See Figure 6. Check each drawer to confirm that it is
aligned:
• Side-to-Side — When viewed from the top, the
drawer front should be square with the sides of the
cabinet.
• Front-to-Back — When viewed from the side, the
drawer front should be straight with the cabinet’s
sides, not cocked forward or back.
• Top-to-Bottom — When viewed from the front, the
drawer should be level horizontally.
If both drawers are properly aligned, go on to 6 Prepare
Power Supply. If either drawer is not aligned, carefully
follow instructions to remove that drawer, make the
necessary adjustment and re-install the drawer.
CAUTION
Use care when handling the drawer. Drawer edges,
drawer rail and the unit’s slide may be sharp.
IMPORTANT
Drawer adjustments are made by moving the slide that
carries the drawer’s rail. Minor adjustments may be made
by loosening one of the slide’s mounting screws, adjusting
the slide and retightening the screw. Severe adjustments
may be made by removing the slides’ mounting screws,
drilling new mounting holes and remounting the slide.
Side-to-Side Adjustment
See Figure 8. The drawer
will need a Side-to-Side
Adjustment if, when
viewed from the top, the
drawer front is not square
with the sides of the
cabinet. This is caused by
one of the slides being
mounted too far forward
on the unit’s liner.
Not Aligned Side-to-Side
Top View of Unit
Figure 8
www.U-LineService.com 8 02/2005
™
2075DWRWC — Drawer Model Wine Captain
®
Minor Adjustment:
Note: The mounting holes
on the slide are slightly
larger than the screws’
Loosen
Mounting Screws
diameter.
1. Loosen the slide’s
mounting screws.
2. Push the slide
backward.
3. Retighten the screws.
See
Figure 9
.
Push Slide
Backward
Figure 9
Severe Adjustment:
Note: The slides have
extra mounting holes that
may be used.
Mark and Drill New
Mounting Holes
1. Remove the slide’s
mounting screws.
2. Reposition the slide so
it is the same distance
from the front of the
liner as the other slide.
Measure to confirm.
Figure 10
Push Slide
Backward
3. Mark new drilling holes
using different sets of mounting holes on the slide. See
Figure 10
.
Note: Front location holes are shown. Corresponding rear
holes will also need to be marked.
4. Drill all the new holes with a #30 drill bit.
5. Remount the slide.
Minor Adjustment:
Note: The mounting holes
on the slide are slightly
larger than the screws’
Screws Should
diameter.
1. Loosen one slide’s
mounting screws.
2. Level the slide.
3. Retighten the screws.
See
Figure 12
4. Repeat procedure for
.
Level the Slide
the other slide.
Figure 12
Severe Adjustment:
Note: The slides have
extra mounting holes that
may be used.
Mark and Drill New
Mounting Holes
1. Loosen one slide’s rear
mounting screws.
2. Remove the slide’s
front mounting screws.
3. Reposition the slide so
it is level.
4. Mark new front drilling
Figure 13
holes using a different
set of mounting holes on the slide. See
5. Drill the new holes with a #30 drill bit.
6. Remount the slide.
7. Repeat procedure for the other slide.
Be Loose
Level the Slide
Figure 13
-hndl
.
Front-to-Back Adjustment
See Figure 11. The drawer
will need a Front-to-Back
Adjustment if, when
viewed from the side, the
drawer front is cocked
forward or back. This is
caused by the front slide
mountings not being level
with the rear slide
mountings.
Figure 11
02/2005 9 www.U-LineService.com
Not Aligned Front-to-Back
Side View of Unit
2075DWRWC — Drawer Model Wine Captain
®
™
Top-to-Bottom (and Left-to-Right)
Adjustment
Not Aligned Top-to-Bottom
Not Aligned Left-to-Right
Top View of Unit
Front View of Unit
Figure 14
See Figure 14. The drawer will need a Top-to-Bottom
Adjustment if, when viewed from the front, the drawer is
not level horizontally. Viewed from the top, one side will
protrude. This is caused by one of the slides being
mounted higher than the other slide on the unit’s liner.
Minor Adjustment:
Note: The mounting holes
on the slide are slightly
larger than the screws’
diameter.
1. Loosen one slide’s
mounting screws.
2. Push the slide upward
or downward to match
the position of the
other slide.
3. Retighten the screws.
See
Figure 15
.
4. Repeat the procedure
with the other slide if
necessary.
Figure 15
Loosen
Mounting Screws
Push Slide
Upward or
Downward
Severe Adjustment:
Note: The slides have
extra mounting holes that
may be used.
Mark and Drill New
Mounting Holes
1. Remove one slide’s
mounting screws.
2. Reposition the slide so
it is the same distance
from the bottom of the
liner as the other slide.
Measure to confirm.
3. Mark new drilling holes
Figure 16
Push Slide
Upward or
Downward
using different sets of
mounting holes on the slide. See
Figure 16
.
Note: Front location holes are shown. Corresponding rear
holes will also need to be marked.
4. Drill all the new holes with a #30 drill bit.
5. Remount the slide.
Re-installation of Drawer
CAUTION
Use care when handling the drawer. Drawer edges,
drawer rail and the unit’s slide may be sharp.
1. Set the drawer’s rails onto the slides.
2. Re-install the rails’ mounting screws. See
Page 8
.
3. Plug in the drawer’s connection wiring (top drawer
only).
4. Go on to
6 Prepare Power Supply
.
Figure 7
on
www.U-LineService.com 10 02/2005
™
2075DWRWC — Drawer Model Wine Captain
®
6 Prepare Power Supply
Electrical Specifications
CAUTION
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician.
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current).
An individual, properly grounded branch circuit or circuit
breaker is recommended. GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be
sure to consult your local codes.
See Figure 17 for recommended receptacle location.
7 Level the Unit
Leveling Information
Note: It is recommended that the unit is level.
1. Use a level to check the levelness of the unit from front
to back and from side to side. Level should be placed
along top edge and side edge as shown (see Figure 18).
Check
Figure 18
Level
23-11/16"
7"
1-1/2"
Figure 17
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Never use an extension cord to connect power to
the unit.
Go on to 7 Level the Unit.
2. If the unit is not level, adjust the feet on the corners of
the unit as necessary (see
Figure 19
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level. Go on to
8 Install the Unit
Figure 19
Turn Foot to Adjust
.
).
Installation Tip
If the room floor is higher than the floor in the cut-out
opening, adjust the rear feet to achieve a total unit rear
"
height of 1/8
the unit height in the front by adjusting the front feet.
This allows the unit to be gently tipped into the opening.
Readjust the front feet to level the unit after it is correctly
positioned in the opening.
less than the opening’s rear height. Shorten
02/2005 11 www.U-LineService.com
2075DWRWC — Drawer Model Wine Captain
®
™
8 Install the Unit
Installation of the 2075DWRWC
1. Plug in the power cord.
2. Gently push the unit into position. Be careful not to
entangle the electrical cord.
3. Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit’s top
surface should be approximately 1/8" below the
countertop.
Anti-Tip Kit Installation
WARNING
• The Anti-Tip Kit must be installed on this unit
before it is used.
• Additional blocking or special fasteners may be
required for installation. Installer is responsible
for secure attachment to prevent the unit from
tipping.
• Make sure the mounting screws attaching the
unit to the counter, cabinet or wall are deep
enough into the mounting surface to support the
weight of the drawers and the items that will be
inside the drawers.
• Never use the drawers as steps or as a shelf to
support more than the drawers’ content. Serious
personal injury could occur.
After leveling, the unit must be secured to a counter, a
cabinet or a wall to prevent tipping.
1. Open the upper drawer to expose the six screws (A)
installed at the top two corners (three at each corner).
Remove the appropriate screws for horizontal or
vertical mounting (see Figure 20). Do not discard.
Horizontal Mounting
(Left Side Shown)
B
A
C
Vertic al M oun tin g
(Left Side Shown)
B
C
A
Figure 20
Countertop or Wall Header
Cabinet or Wall Stud
www.U-LineService.com 12 02/2005
™
2075DWRWC — Drawer Model Wine Captain
®
2. Insert the screws through the anti-tip bracket (B) and
attach the bracket to the unit. Tighten screws securely.
3. Repeat for the other side.
Note: The bracket should be flush with the surface it is
being attached to. If it is not, loosen the screws and slide
the bracket against the mounting surface. Tighten screws
securely.
4. Using two of the screws (C) supplied, fasten the screws
through the bracket and into the counter, cabinet or wall.
IMPORTANT
Certain cabinets or countertops may require special
fasteners or additional wood blocking to anchor properly.
CAUTION
Make sure the screws are back far enough so they do not
damage any exposed front surface of the cabinet.
Installation Troubleshooting
Problem
:
The drawer remains open unless it is pushed closed.
Solution
A:
The drawer should be self-closing when it is open
"
approximately 8
to back of the unit and readjust if necessary.
. If it is not, re-check leveling from front
9 Start-Up for the First Time
Initial Start-Up
Once installation and leveling is complete, the unit is
ready for initial start-up and operation.
Temperature Controller
Figure 21
The temperature controls are integrated in the top, front
drawer panel. They consist of an LED display and touch
sensors for each drawer and a touch sensor to control the
lighting (“ ”, “ ” and “ ”). The LED displays show
the drawer’s temperature set point, and are calibrated in
degrees Fahrenheit. The controls are factory programmed
for a set point of 60°F for the top drawer and 40° F for the
bottom drawer. Each drawer’s display will show its set
point when the unit is first powered up.
Figure 22
02/2005 13 www.U-LineService.com
2075DWRWC — Drawer Model Wine Captain
®
™
To display actual temperature of each drawer, press the
“ ” and “ ” touch sensors simultaneously for three
seconds. The display indicates the actual temperature.
After approximately 10 seconds, the set point
temperature displays.
To adjust the temperature set point, touch and hold
either the “ ” or “ ” for that drawer for three
seconds. When the LED displays “SP,” lift your finger from
the controller and the corresponding LED will begin to
flash the set point. Touch the “ ” or “ ” until the
desired set point displays. Wait 10 seconds for the new set
point to be saved. Wait 24 hours for the temperature to
stabilize before checking the actual temperature again.
Each wine compartment can be set to 40°F to 60°F.
Note: A flashing indicator light (LED dot) indicates a
thermistor error in that drawer. Call for service.
Other Settings
Other settings for the unit are factory preset. No adjustments
should be necessary at this time. See the User Manual for
information on:
• Adjusting the interior lighting
• Removing the lower drawer’s wine caddy
• Using or disabling the cascade feature
Start-Up Troubleshooting
Problem
:
Unit does not appear to turn on when plugged in.
Solution
A:
Make sure outlet has power (circuit breaker has not
tripped).
IMPORTANT
See the User Manual’s Troubleshooting Guide for more
solutions.
www.U-LineService.com 14 02/2005
™
Who to Call
Service Information
If the need for service arises, contact the dealer from
whom the unit was purchased. State the Model Number
and Serial Number and explain the problem. The Model
and Serial Number plate is located inside unit at upper
right hand corner.
If you need to locate a service company, you can go online
at www.U-LineService.com and search for a service
company by zip code.
For more than four decades, U-Line has distinguished itself as the leader in built-in
undercounter ice making, refrigeration and wine storage appliances.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
undercounter icemakers, Combo
refrigerators, refrigerated drawers and refrigerator/freezers.
©2005 U-Line Corporation
Publication No. 30059E
02/2005 Rev. A
®
icemaker/refrigerators, Wine Captain® wine storage units,
Loading...