U-Line H-2590, TDA080 User Manual

H-2590

TAPE ADVANCE BUTTON

HEAVY DUTY AUTOMATIC
TAPE DISPENSER

1-800-295-5510

uline.com

FEATURES

1. When using automatic feed, remove the first piece
of tape. The unit will automatically feed and cut the
next piece at the preset length.

2. Feed length can be easily set using thumbwheel
controls.

HOLD DOWN SHAFT
(UNDER TOP COVER)

MODE SELECTION
(MANUAL, AUTO & INTERVAL)

TAPE LENGTH DISPLAY

INTERVAL KNOB

ALARM

3. Hold down shaft increases accuracy by maximizing
tape adhesion to the feed rollers.

4. The blade is easy to remove and replace.

5. Optional serrated blade for hard to cut materials.

REEL HOLDER

POWER SWITCH

6. Tape Length Display – Shows preset feed length.
Four-digit display can be set from 50-9999mm
(2" - 393").

7. Interval Knob – Sets delay time before dispensing
next piece.

8. Auto/Manual Switch – Toggles operating mode
between manual (press tape advance button
to dispense) and auto (automatic feed and cut
when piece is removed).

9. Power Switch – Press to turn power on and off.

10. Tape Advance Button – Press to feed and cut one
piece of tape to the preset length.

11. Hold Down Shaft – Increases adhesion to feed roller.

12. Reel Holder – 3" core to hold material.

13. Alarm – Lights when there is a malfunction in the unit.

0810 IH-2590PAGE 1 OF 3

SET-UP

1. With power switch off, plug power cord into
dispenser and then into wall outlet.

2. Make sure machine is grounded properly.

3. Set the tape length display to 200mm.

4. Set the auto/manual switch to manual.

5. Turn dispenser power switch on, switch will be
illuminated.

6. Place tape roll on reel holder.

7. Put reel holder into reel holder slots.

OPERATION

1. After tape has been loaded and fed, turn power
switch off.

2. Set tape length display to required length using the
push buttons above and below the
numerical display.

NOTE: The length shown is in millimeters.

3. Flip auto/manual switch to desired location.

4. AUTO: When the cut piece of tape is removed from
the machine, the next piece is automatically fed
and cut. The interval knob will set the time delay
before the next piece is dispensed. Maximum delay
is 25 seconds.

8. Open latched top cover and remove metal hold
down shaft.

9. Press end of tape firmly onto metal feed roller, then
replace hold down shaft over tape and close top
cover.

10. Press tape advance button.

11. Remove tape then press tape advance button
again to ensure proper feeding.

5. MANUAL: The tape advance button must be pressed
each time a piece of tape is needed.

6. The tape will then be fed and cut.

7. Turn power switch on.

8. Press tape advance button to begin dispensing
tape.

NOTE: Tape lengths vary depending on
material. Verify length of first piece.

MODEL

#

TDA080

• Auxili ary sta nd avail able for d iameters up to 24”.

* Depend ent on material.

** Other s izes avail able.

TAPE

WIDTH

.25 to 3.15"

(6.4 to 8.0mm)

CUT

LENGTH

2 to 394"

(50 to 9999mm)

MAX.

OUTSIDE

DIAM ETER

9"

(251mm)

SPECIFICATIONS

3"

ACCURACY

OF CUT

+/- 0.4"

(1mm)

CORE

DIAM ETER**

(76.2mm)

TAPE

*

CUTTER

Automatic Automatic Digital

FEED

TYPE

LENGTH
SETTI NG

WEIGHT DIMENSIONS

21lbs.

(9.5kg)

9"(L) x 6.625"(W) x 12"(H) /

229mm(L) x 168mm(W) x 305(H)

0810 IH-2590PAGE 2 OF 3