U-Line 2275DWRWS, 2275DWRWOL User Manual

Use and Care Guide

Wine Captain® Drawer Model:
2275DWRWS, 2275DWRWOL

2275DWRWS 2275DWRWOL

1 Introduction

Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line
Corporation is the world’s number one manufacturer of built-in, under-counter, specialty refrigeration and ice making
products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology
consistently leads the market with innovation, design, depth of product line and performance.

U-Line products are making life more convenient in homes, businesses, and hotels around the world. U-Line supports its
products with a strong dealer network, and its commitment to quality even extends to environmentally safe packaging.

IMPORTANT

READ all of the instructions in this guide completely before operating the unit for the first time.

For future reference, keep this guide in a safe, accessible location. If you need additional information or assistance,
please contact U-Line Corporation directly. Contact information appears on the rear cover of this guide.

If you have a problem with the operation of this product, the SERVICE section of this guide will assist you in quickly
identifying common problems and provide information on possible causes and remedies. If your product needs service,
contact U-Line directly.

Warranty Registration

Your U-Line Corporation Limited Warranty is located on the inside rear cover of this guide. To validate your warranty, the
product and its original purchase date must be registered. A Warranty Registration Card has been included for this
purpose in the package containing this manual. Complete and mail the Warranty Registration Card, or register your
product online at www.U-LineService.com as soon as possible after purchase.

If your product registration is not on file and a request for warranty coverage is received, the date of sale to the U-Line
Selling Dealer or Distributor will be established as the first date of warranty coverage for your product.

Please Record Your Model Information

When you request additional information or service, you will be asked for your products model and serial numbers. You
can find this information on the serial plate located on the upper right or rear wall in the interior of your unit. This
information also appears on the warranty registration card.

1

ULIN_0023_A

Figure 1

Please record the model number (Figure 1, 1), serial number (Figure 1, 2), date of purchase, and dealer contact
information for your U-Line product below:

Model Number:

_____________________________________________________

Serial Number:

_____________________________________________________

Purchase Date:

_____________________________________________________

Dealer Name:

_____________________________________________________

Dealer Address:

_____________________________________________________

Dealer Telephone:

_____________________________________________________

2

2 2275DWRWS, 2275DWRWOL

2 Table of Contents

Introduction ...............................................................................................................................2

Warranty Registration .......................................................................................................2

Please Record Your Model Information ...........................................................................2

Table of Contents .......................................................................................................................3

Safety Precautions ......................................................................................................................5

Safety Alert Definitions .....................................................................................................5

General Precautions ...........................................................................................................5

Product Features ........................................................................................................................6

Échelon Wine Captain .......................................................................................................6

Operation ...................................................................................................................................7

Initial Startup .....................................................................................................................7

Interior Lighting .................................................................................................................7

Electronic Control Panel ....................................................................................................8

Normal Operating Sounds .................................................................................................9

Wine Stocking Recommendations ....................................................................................9

Storage, Vacation, Moving ..............................................................................................10

Product Disposal ...............................................................................................................10

Wine Guide ...............................................................................................................................11

Wine Selections Suggestions ...........................................................................................11

Suggestions for Matching Food and Wine .....................................................................11

Common Food and Wine Matches ..................................................................................11

Cleaning and Maintenance .....................................................................................................13

General Cleaning .............................................................................................................13

Maintenance ....................................................................................................................13

Adjust Drawers .................................................................................................................15

Service .......................................................................................................................................21

Before Calling for Service ................................................................................................21

If Service is Required ........................................................................................................21

Replacement Parts ...........................................................................................................21

Troubleshooting Guide ....................................................................................................22

U-Line Corporation Limited Warranty ....................................................................................23

2275DWRWS, 2275DWRWOL 3

This page intentionally left blank

4 2275DWRWS, 2275DWRWOL

3 Safety Precautions

WARNING

• PLEASE READ all instructions completely before
attempting to install, operate, or service your
unit.

• Proper installation procedures must be followed
if this unit is being initially installed, or is moved
to a new location after being in service. An
INSTALLATION GUIDE for your unit, providing
complete installation information is available
from U-Line Corporation directly, and must be
consulted before any installation is begun. U-Line
contact information appears on the rear cover of
this guide.

• This unit requires connection to a grounded
(three-prong), polarized receptacle that has been
placed by a qualified electrician in accordance
with applicable electrical codes.

Safety Alert Definitions

Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:

DANGER

Danger means that failure to follow this safety
statement will result in severe personal injury or
death.

WARNING

Warning means that failure to follow this safety
statement could result in serious personal injury
or death.

CAUTION

Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.

General Precautions

Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:

DANGER

RISK OF CHILD ENTRAPMENT. Before you throw away
your old refrigerator or freezer, take off the doors
and leave shelves in place so that children may not
easily climb inside.

SHOCK HAZARD - Electrical Grounding Required.

• Never attempt to repair or perform
maintenance on the unit until the electricity
has been disconnected.

• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.

• Altering, cutting of power cord, removal of
power cord, removal of power plug, or direct
wiring can cause serious injury, fire and/or loss
of property and/or life, and will void the
warranty.

• Never use an extension cord to connect power
to the unit.

• Always keep your working area dry.

WARNING

The Anti-Tip Kit must be installed on this unit
before it is used. Never use the drawers as steps
or as a shelf to support more than the drawers’
contents. Serious personal injury could occur.

CAUTION

• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp
edges.

• If your model requires defrosting, DO NOT use any
type of heater to defrost. Using a heater to speed
up defrosting can cause personal injury and
damage to the inner lining.

IMPORTANTIMPORTANT

• Do not lift unit by drawer handles.

• Never install or operate the unit behind closed
doors. Be sure front grille is free of obstruction.
Obstructing free air flow can cause the unit to
malfunction and may void the warranty.

• Failure to clean the condenser every three months
can cause the unit to malfunction. This could void
the warranty.

• Allow unit temperature to stabilize for 24 hours
before use.

• If your model requires defrosting, never use an
ice pick or other sharp instrument to help speed
up defrosting. These instruments can puncture
the inner lining or damage cooling unit.

• Use only genuine U-Line replacement parts.
Imitation parts can damage the unit, affect its
operation or performance and may void the
warranty.

2275DWRWS, 2275DWRWOL 5

4 Product Features

Échelon Wine Captain

Your U-Line Wine Captain is the industry’s only built-in
under the counter two drawer wine storage unit with
dual zone temperature control and up to 43 bottle (750
mL size) capacity. Your Wine Captain will accommodate
up to 24 bottles in the top drawer and up to 19 bottles in
the bottom drawer. The bottom drawer also includes a
wine caddy for elegant transportation and service of
three bottles of wine. The corks remain moist, which
keeps air from entering the bottles.

The Right Temperature for Wine

Your Wine Captain is designed to provide a temperature
zone in each drawer, adjustable between 40 - 60°F, so the
specific storage requirements of your finest wines can be
satisfied.
NOTE: Product temperatures, not air temperatures, are
referenced above.

Features of Échelon Wine Captain

• An electronic control panel with digital display allows
you to display the actual temperature in each drawer,
and adjust the individual temperature setting to your
personal preference. The electronic control and digital
display provides an attractive appearance, and its
method of control provides precise temperatures for
storage of one or multiple types of wine.

• An interior light will illuminate automatically in each
drawer as it is opened, providing easy visual
identification of the wine. However, you can easily
select two other modes of operation:

a. Interior lights in both drawers can be illuminated

while the drawers are closed, providing an
attractive display of your wine collection.

b. A blackout/Sabbath mode (not Star K certified)

allows you to darken both interior lights and the
LED display, while maintaining complete
temperature control in both drawers.

• Automatic (cycle) defrost means maintenance-free
defrosting.

• Wine racks have a contoured maple front trim that
adds a fashionable appearance to Wine Captain. The
wood facing may be stained or replaced in its entirety
with other woods or manufactured products (such as
Corian® or Sandstone).

• Black vinyl wine racks blend with the wine bottles,
placing greater emphasis on the wines themselves. The
vinyl holds the wine bottles more effectively than a
chromed or painted finish.

• All units feature a vinyl clad steel cabinet that provides
a rich textured look, and resists scratching, peeling and
flaking.

• Stainless models feature a stainless steel wrap and
sculpted stainless handles.

• Wood overlay units feature the ability to match
cabinetry. Handles are not included with overlay units.

• Both drawers feature tinted thermal glass that protects
your wines from potentially harmful light rays while
providing a very fashionable appearance.

• Wine Captain models are not recommended for
outdoor use.

• This Wine Captain cannot be configured for a free­standing installation. It must be installed as a built-in,
under counter unit, and must be anchored to prevent
tipping using the originally provided anti-tip kit.

Features and specifications are subject to change without
notice.

6 2275DWRWS, 2275DWRWOL

5 Operation

Interior Lighting

The interior of the cabinet can be illuminated whenever a
drawer is opened (default mode) or illuminated for a
four-hour period.

The LIGHT icon (Figure 3, 5) on the control panel is used
to change the lighting functions.

To illuminate the interior of the cabinet for a four-hour
period:

ULIN_0080_A

Figure 2

IMPORTANTIMPORTANT

Proper air flow (Figure 2) is required for your unit to
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.

Initial Startup

All U-Line units are shipped with controls that are preset.
No initial adjustments are required.

IMPORTANTIMPORTANT

U-Line recommends the unit be allowed to run
overnight prior to loading with product.

123 54

ULIN_0184_A

1. Touch and release the LIGHT icon (Figure 3, 5) to

switch from drawer-operated lighting control to
continuous lighting (the °F symbol will flash briefly
after the LIGHT icon is pressed).

2. To return to drawer-operated lighting control before

the four-hour period is up, repeat Step 1.

Figure 3

To turn the unit on or off, touch and hold the POWER icon
(Figure 3, 1) on the display panel for approximately five
seconds until the °F symbol flashes and release.

• A small LED above the icon will illuminate to confirm
the touch of any controller icon.

• The display (Figure 3, 3) will show the unit set-point
temperature when the unit is on and will show OFF
when the unit is off.

• Turning the unit off will override any other control
function.

2275DWRWS, 2275DWRWOL 7

Electronic Control Panel

Your Wine Captain has been designed to provide two
temperature zones within the cabinets so the specific
storage requirements of your finest wines can be satisfied.
NOTE: These are product temperatures, not air
temperatures.

123 54

ULIN_0184_A

Figure 4

The electronic control with digital display (Figure 4) is
configured to show a single temperature continuously.
This set-point temperature is a base number used by the
controller to maintain the temperature zones in your unit.
The factory default set-point temperature is 60°F in the
top drawer and 40°F in the bottom drawer. This set-point
temperature is used as a gauge if further temperature
adjustments are required.

A DISPLAY OFF mode is available through the control
panel. This mode allows you to control whether the
display (Figure 4, 3) will be ON or OFF whenever the
door is closed. The icon touch sequence that follows will
switch between both modes:

1. Touch and hold the WARMER icon (Figure 4, 2), and

within five seconds press the POWER icon
(Figure 4, 1) three times.

2. The display will be either visible or dark when the door

is closed.

3. To return to the previous mode, repeat Step 1.

Temperature Display Selection

U-Line products supplied for 110 VAC operation have
temperatures displayed in a default Fahrenheit (°F)
configuration (Figure 4, 3).

The display can easily be adjusted for either type of
temperature display. Press and hold the LIGHT icon
(Figure 4, 5) and within five seconds press the COOLER
icon (Figure 4, 4) three times to change the display as
desired.

Temperature Display

Checking Product Temperature

ULIN_0093_A

Figure 5

To check the actual product temperature in your unit,
insert an accurate thermometer into a plastic (non­breakable) bottle that is partially filled with water.
Tighten the bottle cap securely (Figure 5).

Place the bottle in the desired area for 24 hours. Refrain
from opening the unit during the testing period. After 24
hours, check the temperature of the water. If required,
adjust the temperature control in a small increment (See
ADJUSTING TEMPERATURE).

Factors which affect the internal temperatures of the
cabinet include:

• Temperature setting.

• Ambient temperature where installed.

• Number of times and length of time the door is
opened and closed.

• Installation in direct sunlight or near a heat source.

Adjusting Temperature

IMPORTANTIMPORTANT

Adjust the set-point temperature in single
increments, and wait 24 hours for the temperature
to stabilize before rechecking.

123 54

To display all zone temperatures:

1. Press and hold the WARMER icon (Figure 4, 2) for
approximately five seconds and release when the °F
symbol in the display (Figure 4, 3) begins to flash.

2. The display
reading on each drawer.

8 2275DWRWS, 2275DWRWOL

(Figure 4, 3)

will show an individual

ULIN_0184_A

Figure 6

To adjust the set-point temperature:

1. Press and release the WARMER icon. The top of the F
in °F (Figure 7, 1) of the top drawer will begin to
flash. This will allow you to adjust the temperature of
the top drawer. In 10 seconds of inactivity, the bottom
bar of the F in °F (Figure 7, 2) will begin to flash; this
will allow you to adjust the temperature of the
bottom drawer. Adjustments to the lower drawer can
be made immediately if the LIGHT icon is pressed.

21

ULIN_0830_A

Figure 7

Wine Stocking Recommendations

Specially designed wine racks allow for the proper
horizontal storage of wine. The bottles are properly
positioned so the wine remains in contact with the cork to
assure that the cork does not become dry.

Stock your unit as follows:

2. While the top or bottom bar of the F in °F is flashing,
press the WARMER or COOLER icon as required to
adjust the set-point temperature. The change will be set
five seconds after adjusting the temperature and the
new set-point temperature wil be displayed. Allow the
unit to sit for 10 seconds to return to normal mode.

Normal Operating Sounds

All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. In spite of
this technology, your model may make sounds that are
unfamiliar.

Normal operating sounds may be more noticeable
because of the unit’s environment. Hard surfaces such as
cabinets, wood/vinyl/tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.

Common refrigeration components, and a brief
description of the normal operating sounds they make,
are listed below. NOTE: Your product may not contain all
of the components listed.

• Compressor: The compressor makes a hum or pulsing

sound that may be heard when it operates.

• Evaporator: Refrigerant flowing through an evaporator

may sound like boiling liquid.

• Condenser Fan: Air moving through a condenser may be

heard.

• Automatic Defrost/Drain Pan: Water may be heard

dripping or running into the drain pan when the unit is in
the defrost cycle.

ULIN_0242b_A

Figure 8

1. The bottom drawer should be stocked first. Open the
drawer, and beginning at the back of the lowest rack
work forward, staggering the bottles as shown
(Figure 8).

2. Stock the second rack in the same manner.

3. Close drawer slowly.

ULIN_0243b_A

Figure 9

4. Repeat steps 1 through 3 to stock the racks in the upper
drawer.

NOTE: After stocking, allow unit to run for 24 hours
to stabilize product temperatures.

2275DWRWS, 2275DWRWOL 9

Wine Caddy

ULIN_0153a_A

Figure 10

The bottom drawer includes a three bottle caddy
(Figure 10) for elegant transportation and wine service.

To access and remove the bottle caddy:

1. Open the bottom drawer fully and grasp the caddy
handle from either side.

2. While supporting the bottom of the caddy with one
hand, slowly and gently pull it out from under the
drawer.

3. Close the drawer completely.

To replace the bottle caddy:

1. Open the bottom drawer fully.

2. Support the bottom of the caddy with one hand while
picking up the caddy. Gently slide the caddy into place
under the drawer.

Storage, Vacation, Moving

If the unit will not be used for an extended period, or
otherwise stored, follow these steps completely:

WARNING

Electrical Shock Hazard. Disconnect power before
servicing. Before operating, replace all panels.
Failure to do so may result in death or electrical
shock.

1. Remove all consumable contents from the unit.

2. Disconnect the power cord from its outlet, and leave it
disconnected until the unit is returned to service.

3. Clean and dry the interior of the cabinet (See CLEANING
AND MAINTENANCE: GENERAL CLEANING).

4. During periods of non-use, the cabinet must remain
open to prevent the formation of mold and mildew.
Open drawer a minimum of 2" (5 cm) to provide the
necessary ventilation.

Product Disposal

If the unit is being removed from service for disposal,
check and obey all Federal, State and/or Local regulations
regarding the disposal and recycling of refrigeration
appliances, and follow these steps completely:

1. Remove all consumable contents from the unit.

2. Disconnect power to the unit and unplug the power
cord from its outlet.

DANGER

RISK OF CHILD ENTRAPEMENT. Before you throw
away your old unit, remove the drawers.

3. Ensure that the caddy is centered, and close the drawer
completely.

10 2275DWRWS, 2275DWRWOL

6 Wine Guide

Suggestions for Matching Food and
Wine

Wine Selections Suggestions

Selecting the right wine for the right occasion can
sometimes be a seemingly awkward or difficult task for
the beginning wine enthusiast. We would therefore like
to present you with a few suggestions which may provide
a little more confidence and enjoyment when choosing
and serving your wines.

When selecting wines, keep an open mind and do not be
afraid to be adventurous. Do not view the subject of wine
so seriously it discourages you from learning and
discovering for fear of embarrassment if something is
incorrect. Wine is best viewed as a hobby and enjoyed.

When assembling your collection, try not to become
obsessed with “Vintages.” Although a chart can be a
useful tool, generalizations about a specific year have led
more than one collector to disappointment. In many
instances an “Off Year” will provide a better value and
more drinking enjoyment.

The primary guideline to the subject of wine is your own
palate. Do not be afraid to make mistakes. Experiment,
discover, but most of all, enjoy yourself and your new
U-Line product.

Although there are no hard fast rules for matching wine
to food, observe some guidelines. Delicate dishes should
be accompanied by lighter more delicate wines. Full­flavored foods should be matched with fuller-bodied
wines.

As a general rule, one should aim to ascend in flavor and
quality of wines served.

Tabl e 1

Serve a: Before a:

DRY wine SWEET wine

WHITE wine RED wine

YOUNG wine OLD wine

LIGHT-BODIED wine FULL-BODIED wine

Any step back in quality will be noticed. If a fine wine is
tasted prior to a lesser wine, many of the fine wine’s
subtle qualities may be missed.

Common Food and Wine Matches

Tabl e 2

Foods Wines

Fish, Shell Fish, Crab, Oysters Dry White Wines, Light

Sparkling or Extra Dry

Champagne
Beef, Venison Full-Bodied Red Wines
Pork, Veal, Lamb and Poultry Light-Bodied Red Wines
Fruit Sweet White and Sparkling

Wines

2275DWRWS, 2275DWRWOL 11

Guide to Common Styles of Wine

Red Wines

Full-Bodied Dry California

French
Italian

Medium-Bodied Dry California

French

Light-Bodied Dry French

Italian

White Wines

Full-Bodied Dry California

French

Medium-Bodied Dry California

French

Light-Bodied Dry French Chablis, Muscadet, Pouilly-Fume

Full-Bodied, Very Sweet Germany

Frency
Hungary

Medium-Bodied, Semi-Sweet California

Germany

Light-Bodied Off Dry Germany Rhine, Mosel, Riesling

Zinfandel, Cabernet
Rhone, Chateauneuf-du-Pape
Barbaresco, Barolo

Pinot Noir
Bordeaux, Burgundy

Beaujolais
Chianti, Bardolino

Chardonnay
Montrachet, Meursault
Puligny-Montrachet

Sauvignon-Blanc
Pouilly-Fuisse, Sancerre,
Vouvray, Graves

Beerenauslese
Sauternes
Tokay

Gewurtztraminer
Liebfraumilch

Common Tasting Terms

Terminology Description

Acidity A critical element of wine that is responsible for preserving the wines freshness. Excess acidity results in an

Balance A desired trait where tannin, fruit and acidity are in total harmony. Wines with good balance tend to age

Body The weight and presence of wine in the mouth provided by the alcohol and tannin level. Full-bodied wines

Bouquet The blending of a wine's aroma within the bottle over a period of time, caused by volatile acidity.

Complex A subjective term often used in tasting. A wine is said to be complex if it offers a variety of flavors and scents

Flabby A wine that lacks structure, or is heavy to the taste, lacks acidity.

Full-Bodied Wine high in alcohol and extract, generally speaking, fills the mouth, powerful.

Lean Generally describes wines that are slim, lacking of generosity or thin.

Oaky A desirable flavor imparted to wine if done in moderation. Most wines are aged in oak barrels one to three

Tannin Tannins are extracted from the grape skins and stems and are necessary for a well-balanced red wine. Tannins

overly tart and sour wine.

gracefully.

tend to have this strong concentration.

that continue to evolve as it develops.

years, thereby receiving this toasty oak characteristic. However, if a weak wine is left in contact too long with
an oak barrel it will tend to be overpowered with an oaky taste.

are easily identified in wine tasting as the drying sensation over the gums. Tannins generally fade as a wine
ages.

12 2275DWRWS, 2275DWRWOL

7 Cleaning and Maintenance

General Cleaning

Exterior Cleaning (As Required)

• Stainless steel surfaces and components can discolor
when exposed to chlorine gas, pool chemicals, salt
water or cleaners with bleach.

• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
polish on a monthly basis. For best results use Claire
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation (P/N 173348).
Comparable products are acceptable. Frequent
cleaning will remove surface contamination that could
lead to rust. Some installations may require cleaning
on a weekly basis.

• Do not clean with steel wool pads.

• Do not use cleaners that are not specifically
intended for stainless steel on stainless steel
surfaces (this includes glass, tile and counter
cleaners).

• If any surface discoloring or rusting appears, clean it
quickly with Bon-Ami
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.

• Using abrasive pads such as Scotchbrite™ will
cause the graining in the stainless steel to
become blurred.

• Rust that is not cleaned up promptly can penetrate into
the surface of the stainless steel and complete removal
of the rust may not be possible.

®

or Barkeepers Friend Cleanser®

®

Maintenance

Proper maintenance of your U-Line product will ensure
efficiency, top performance and long life. The
maintenance intervals listed are based on normal
conditions. You may want to shorten the intervals if you
have pets or other special considerations.

Defrosting

Automatic (Cycle) Defrost Models

Automatic defrost models do not produce frost in normal
operating conditions. However, a frost pattern may be
noticed on the interior walls if the unit is repeatedly
opened in a high heat or high humidity location. If this
frost pattern does not clear within 24 hours, your unit will
require manual defrosting.

WARNING

DO NOT use any type of electrical heating device,
ice pick, knife or other sharp instrument to
defrost; this could damage the inner lining or
refrigeration system and void the warranty.

IMPORTANTIMPORTANT

The drain pan was not designed to capture the
water created when manually defrosting. To
prevent water from overflowing the drain pan,
place towels or other absorbent materials over the
interior drain trough, under the evaporators
(Figure 11, 1), before defrosting.

1

Interior Cleaning (As Required)

• Disconnect power to the unit. Clean the interior and all
removed components using a mild non-abrasive
detergent and warm water solution applied with a soft
sponge or non-abrasive cloth. Rinse the interior using a
soft sponge and clean water.

• Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transmit
taste to the interior products and damage or
discolor the interior.

2275DWRWS, 2275DWRWOL 13

ULIN_0235_A

Figure 11

To defrost:

1. Turn unit off.

2. Remove all products from the interior and open the

drawer(s) (2" (5 cm) minimum).

3. Allow the frost to completely melt naturally. Clean the

interior and all removed components using a mild non­abrasive detergent and warm water solution applied

NOTE:

with a soft sponge or non-abrasive cloth.

DO
NOT use any solvent-based or abrasive cleaners. They
will discolor or damage the interior.

4. Dampen a soft sponge or non-abrasive cloth in clean
water and wipe down the cabinet interior and removed
components to remove any detergent residue. Rinse the
sponge or cloth in clean water and repeat as necessary
until the cabinet and components are clean.

5. When the interior is dry, turn unit back on.

Condenser Cleaning

Interval - Every Three Months

To maintain operational efficiency, keep the front grille
free of dust and lint and clean the condenser every three
months. Depending on environmental conditions, more
or less frequent cleaning may be necessary.

4. Clean the condenser coil

(Figure 12, 2)

using a soft
brush with a “combing” action or vacuum cleaner. Do
not touch the condenser coil.

5. Position the grille to align the mounting screws with
the holes in the cabinet.

6. Secure, but do not over-tighten both grille screws.

7. Reconnect power to the unit.

Leveling

WARNING

Disconnect electric power to the unit before
cleaning the condenser.

To remove and replace the grille for access to the
condenser fins, follow this procedure:

1

ULI

N_

0

23

6_

A

2

Figure 12

1. Disconnect electrical power to the unit.

2. Loosen two screws

(Figure 12, 1)

completely.

NOTE: Screws are held in the grille by o-ring retainers,
and will not come free of the grille.

3. Remove the grille.

WARNING

Check Level

ULIN_0152a_A

Figure 13

1.

Use a level to check the levelness of the unit from front
to back and from side to side. Level should be placed
along top edge and side edge as shown

1

(Figure 13)

ULIN_0044_A

.

Figure 14

2. If the unit is not level, adjust the feet on the corners of
the unit as necessary

(Figure 14)

.

3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level.

DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.

CAUTION

DO NOT use any type of cleaner on the condenser
unit.

14 2275DWRWS, 2275DWRWOL

Adjust Drawers

Adjusting Drawer Alignment

Checking Drawer Alignment

The unit’s drawers are aligned at the factory before
shipment. However, their alignment could have been
disturbed during shipment.

Aligned
Front-to-Back

Aligned

Side-to-Side

Aligned

Top-to-Bottom

ULIN_0001a_A

Figure 15

See Figure 15. Check each drawer to confirm that it is
aligned:

• Side-to-Side — When viewed from the top, the
drawer front should be square with the sides of the
cabinet.

• Front-to-Back — When viewed from the side, the
drawer front should be straight with the cabinet’s
sides, not cocked forward or back.

• Top-to-Bottom — When viewed from the front, the
drawer should be level horizontally.

If either drawer is not aligned, carefully follow
instructions to remove that drawer, make the necessary
adjustment and re-install the drawer.

WARNING

SHOCK HAZARD — The unit must be unplugged
from the wall outlet during drawer removal,
adjustment and re-installation.

Drawer Removal

Mounting

Screw

ULIN_0001b_A

Figure 16

1. Confirm that the unit is unplugged from wall outlet.

2. Unplug the drawer’s connection wiring (top drawer
only).

3. Remove the mounting screws. See

Figure 16

.

4. Pull the drawer completely out of the unit.

CAUTION

Use care when handling the drawer. Drawer edges,
drawer rail and the unit’s slide may be sharp.

IMPORTANTIMPORTANT

Drawer adjustments are made by moving the slide
that carries the drawer’s rail. Minor adjustments
may be made by loosening one of the slide’s
mounting screws, adjusting the slide and
retightening the screw. Severe adjustments may be
made by removing the slides’ mounting screws,
drilling new mounting holes and remounting the
slide.

2275DWRWS, 2275DWRWOL 15

Side-to-Side Adjustment

Not Aligned Side-to-Side

Severe Adjustment:

NOTE: The slides have extra mounting holes that
may be used.

Mark and Drill New

Mounting Holes

Top View of Unit

ULIN_0001c_A

Figure 17

See Figure 17. The drawer will need a Side-to-Side
Adjustment if, when viewed from the top, the drawer
front is not square with the sides of the cabinet. This is
caused by one of the slides being mounted too far
forward on the unit’s liner.

Minor Adjustment:

NOTE: The mounting holes on the slide are slightly
larger than the screws’ diameter.

Loosen

Mounting Screws

Push Slide

Backward

Push Slide

Backward

ULIN_0001e_A

Figure 19

1. Remove the slide’s mounting screws.

2. Reposition the slide so it is the same distance from the
front of the liner as the other slide. Measure to confirm.

3. Mark new drilling holes using different sets of
mounting holes on the slide. See

Figure 19

.

NOTE: Front location holes are shown.
Corresponding rear holes will also need to be
marked.

4. Drill all the new holes with a #30 drill bit.

5. Remount the slide.

Front-to-Back Adjustment

Not Aligned Front-to-Back

ULIN_0001d_A

Figure 18

1. Loosen the slide’s mounting screws.

2. Push the slide backward.

3. Retighten the screws. See

Figure 18

.

See Figure 20. The drawer will need a Front-to-Back
Adjustment if, when viewed from the side, the drawer
front is cocked forward or back. This is caused by the front
slide mountings not being level with the rear slide
mountings.

16 2275DWRWS, 2275DWRWOL

Side View of Unit

ULIN_0001f_A

Figure 20

Minor Adjustment:

NOTE: The mounting holes on the slide are slightly
larger than the screws’ diameter.

Screws Should

Be Loose

Level the Slide

Wood Overlay

Frame Preparation

An overlay frame covers the drawer front to give a built­in appearance. Appropriate hardware and a copy of these
instructions will be included in the unit.

IMPORTANTIMPORTANT

The thickness of the overlay frame must be 3/4".
The drawer frame must not weigh more than 10 lbs.

Create two frames to the dimensions shown in Figure 23.

ULIN_0001g_A

Figure 21

1. Loosen one slide’s mounting screws.

2. Level the slide.

3. Retighten the screws. See

Figure 21

.

4. Repeat procedure for the other slide.

Severe Adjustment:

NOTE: The slides have extra mounting holes that
may be used.

Mark and Drill New

Mounting Holes

Level the Slide

ULIN_0001h_A

Figure 22

1. Loosen one slide’s rear mounting screws.

2. Remove the slide’s front mounting screws.

3. Reposition the slide so it is level.

4. Mark new front drilling holes using a different set of
mounting holes on the slide. See

Figure 22

.

5. Drill the new holes with a #30 drill bit.

6. Remount the slide.

23-13/16"

2-3/4" Typ

4 Sides

3/4"

14-13/16"

ULIN_0620_A

Figure 23

1. Make sure unit is unplugged from the electrical outlet.

NOTE: If cabinet handles are installed, make sure
the mounting screw heads are below (countersunk)
the back surface of the overlay.

2. Starting with the TOP drawer, open drawer fully.

You should have already prepared the overlay panel
and have the cabinet handles installed.

7. Repeat procedure for the other slide.

2275DWRWS, 2275DWRWOL 17

Light Bulb Replacement

4

3

2

1

ULIN_0154a_A

Figure 24

3. Place finished drawer overlay panel
front of drawer and using masking tape, tape to front
of drawer, making sure to center overlay and making
the top and bottom flush with drawer.

4. Place drawer overlay bracket
of drawer making sure to catch the back of the drawer
with the short lip on bracket.

Also align the wood overlay with the ends of the
bracket, and tape in place.

5. Mark center of holes from mounting bracket onto the
wood overlay.

6. Using an ice pick, or similar tool, mark the location of
the top mounting screws on the wood overlay.

7. Remove the lower mounting bracket and wood overlay
from the drawer.

8. Using a #44 (0.094) drill, pre-drill pilot holes in the
locations noted from steps 5 and 6, be sure to NOT drill
through the overlay.

Drill the pilot hole from step 5, 9/16" deep and the
ones from step 6, 1/4" deep.

9. Attach the bottom bracket to the wood using 2 of the
5/8" screws

(Figure 24, 2)

included with the unit.

(Figure 24, 3)

(Figure 24, 1)

over

on bottom

To replace the light bulb in your U-Line unit:

1

Figure 25

1. Grasp the edges of the light housing lens
(Figure 25, 1) opposite the exposed tab and gently
push the lens toward the tab (Figure 25, 2).

2. Pull the edge of the lens down
swing it out of the light housing.

2

ULIN_0001_A

(Figure 25, 1)

and

IMPORTANTIMPORTANT

ALWAYS use a genuine U-Line replacement bulb (P/N

31317) in the light housing. Use of any other bulb

within the housing will generate excessive heat,
causing damage to the light housing and cabinet
interior, and will compromise the precise
temperature control of your unit.

3. Replace the bulb only with a genuine U-Line P/N 31317
replacement.

4. Replace the lens by first inserting the tab side back into
the housing at a slight angle. While gently pushing the
lens towards the tab end, push the free end up into the
housing, and release when you will hear a snap/click.

Wine Rack Removal/Installation

To remove a rack from the cabinet:

1. Grasp the end of the rack, and gently slide it out until
it stops.

2. Remove any bottles stored on the rack.

10. Attach the wood overlay assembly to the drawer
starting at the bottom of the drawer, then re-centering
it on the drawer front.

11. Secure the top of the wood panel by placing 2 of the
1-1/2" wood screws
holes in the drawer, and tighten securely.

12. Repeat steps for bottom drawer.

18 2275DWRWS, 2275DWRWOL

(Figure 24, 4)

through the top

ULIN_0155a_A

Figure 26

3. Press the left rack release lever
at the same time, lift the corresponding right rack
release lever up, and pull the rack out until it is free of
the tracks and the cabinet.

(Figure 26)

down, and

IMPORTANTIMPORTANT

Do not remove the track side rails from the cabinet.

To insert a rack in the cabinet:

1. Align the left and right rack channels with the tracks
in the cabinet, and ensuring an even track
engagement on both sides, gently push the rack into
the cabinet until it stops.

2. Before reloading the rack, ensure proper operation of
the travel stops in the left and right track rails by
pulling the rack out gently until it completely stops.

Wood Trim Finishing

The U-Line Wine Captain® is equipped with wood­trimmed wine racks that are coated at the factory with a
clear vinyl sealer, which will adequately protect the wood
in normal usage. A final finish coat was not applied so
that the wood trim could be stained to match décor. The
trim on the racks may be coated with a final finish or
stained.

WARNING

To prevent permanent damage to the inner liner
of your unit, the wood trim MUST be removed
from the unit for staining and/or finishing. Allow
stain/finish to dry thoroughly (at least 24 hours
per coat) in accordance with the product
manufacturer’s instructions prior to
reinstallation. Failure to do so may cause the
inner liner of the unit to have a permanent odor,
which is not covered by the warranty.

If staining the trim is desired, it must be done before the
application of any type of final finish. Review the
following staining/final finish and final finish-only
guidelines when staining/ and or sealing the wood to
ensure proper adhesion and durability of the finish.

NOTE: Glass in door is tinted. Stain may look darker
when door is closed.

Staining and final finish application:

1. Remove all screws securing wood trim to interior
components, and remove the trim from the cabinet
interior.

To remove the top drawer display wood trim:

1

4

5

3

Figure 27

2. Remove the two screws (Figure 27, 1), securing trim
to wine rack assembly (Figure 27, 2).

NOTE: Your model will contain an electronic display panel
(Figure 27, 3) in the middle level trim piece. After

removing the trim screws, and gently pulling the trim
from its location, a wiring harness connector
(Figure 27, 4) will become visible. Unplug the connector.

3. Remove the two screws, securing the electronic control
to the wood trim. Carefully rotate the wood trim so the
electronic control slides out of the wood, and place the
electronic control aside in a safe location.

NOTE: The electronic control and glass front are NOT
connected. Be careful when removing the control
not to drop the glass.

ULIN_0831_A

3

1

2

ULIN_0145a_A

Figure 28

4. Remove the two screws
wine rack assembly

2275DWRWS, 2275DWRWOL 19

(Figure 28, 1)

(Figure 28, 2)

securing trim to

.

NOTE: Your model will contain an electronic display
panel (Figure 28, 3) in the wine rack attached to the
bottom drawer. After removing the trim screws,
and gently lifting the trim from its location, a
wiring harness connector will become visible.
Unplug the connector. DO NOT remove drawer from
unit.

5. Remove the two screws securing the electronic control
to the wood trim. Carefully rotate the wood trim so the
electronic control slides out of the wood and place
electronic control aside in a safe location.

NOTE: the electronic control and glass front are NOT
connected. Be careful when removing control not to
drop the glass.

6. Remove the remaining wood fronts from the additional
racks by extending racks out as far as possible and then
removing the three screws that attach the wood to the
racks.

IMPORTANTIMPORTANT

DO NOT apply stain/final finish to the wood trim
with the electronic display attached to the wood.
Damage may occur to the electronic control which
is not covered by the warranty.

Final finish-only application:

1. Follow steps 1 through 6, then continue with step 2 in
this section.

2. Lightly scruff sand the wood trim with 280 or finer grit
sandpaper.

3. Remove sanding dust with a clean, dry cloth.

4. The factory-applied seal is compatible with virtually all
finishes. A low odor, water clean up, quick-drying finish
such as Minwax® Polycrylic® Protective Finish is

®

recommended (Minwax

Polycrylic® is an ultra fast­drying water-based finish). Apply a thin coat of a clear,
protective finish, following the container label
directions.

5. Lightly sand and reapply if desired.

6. Allow the final coat to dry for 24 hours before
reinstalling the display to bottom drawer trim and
remaining trim to the cabinet interior components.

IMPORTANTIMPORTANT

DO NOT use oil-based stains on wood trim. Vapors
from oil-based stains will permanently penetrate
the liner and will not dissipate over time.

7. Apply Minwax® Water-Based Wood Stain to wood with
a synthetic bristle brush or a foam applicator. Allow
stain to penetrate approximately three minutes. Before
the stain is dry, take a stain dampened rag and remove
any excess stain remaining. Wipe in the direction of the
grain with medium pressure to achieve the desired stain
color.

8. After two hours, repeat step 2. This will even out the
color of the wood.

9. Allow stain to dry for a minimum of three hours before
applying the final finish.

10. If desired, sand the wood with very fine sandpaper to
smooth the surface after the staining process.

11. Remove all dust from the wood, and apply one coat of
Minwax
bristle brush to the wood. This finish should be applied
in a thin coat following the direction of the grain.
Apply the finish to the back and sides of the wood first,
and allow it to dry for two hours. Apply the finish to the
front side of the wood next, and allow it to dry for two
hours. Sand with very fine 220 grit sandpaper. Apply
two addition coats of the finish in the same manner, but
do not sand the trim after the final third coat is applied.

®

Polycrylic® Protective Finish using a synthetic

12. Allow the final coat to dry for 24 hours before
reinstalling the trim to the cabinet interior components.

20 2275DWRWS, 2275DWRWOL

8 Service

Before Calling for Service

If your U-Line product appears to be malfunctioning, read
through the OPERATION section of this guide to ensure
that the function of all controls are clearly understood. If
the malfunction persists, the TROUBLESHOOTING GUIDE
in this guide will assist you in quickly identifying common
problems, and provide information on possible causes and
remedies. Most often, this will resolve the problem
without the need to call for service.

If Service is Required

If you do not understand a troubleshooting remedy, or
your product needs service, contact U-Line Corporation
directly. Contact information appears on the rear cover of
this guide.

You will be asked for your product Model and Serial
Numbers. This information should be recorded inside the
front cover of this guide, following the products original
purchase. It also appears on the Model and Serial number
plate located on the upper right or rear wall of the
interior of your product.

Replacement Parts

When you need replacement parts, always request that
genuine U-Line replacements be used. U-Line products
have been designed and engineered using components
that work efficiently, and provide superior service life and
performance. The use of aftermarket parts or components
may affect the safety, operation, performance or
durability of your product, and may also void its warranty.

2275DWRWS, 2275DWRWOL 21

Troubleshooting Guide

DANGER

ELECTROCUTION HAZARD
Never attempt to repair or perform maintenance on
the unit until the main electrical power has been
disconnected.

Troubleshooting - What to check when problems occur:

PROBLEM POSSIBLE CAUSE REMEDY

Unit does not operate and
electronic display is blank.

No interior light Loose or burned out bulb Tighten or replace bulb (See MAINTENANCE; LIGHT

Unit not cold enough. Check
temperatures (See OPERATION for
approximate temperatures).

Unit is too cold. Check temperatures
(See OPERATION for approximate
temperatures).

The unit frosts up. High ambient temperatures or

Noise during operation. Certain sounds are normal. Soft sounds from the fan and water/dropping sounds

Drawer(s) can't close. Item(s) interfering with drawer Adjust items in drawer(s).

No electrical supply Plug unit in or check circuit breaker.

BULB REPLACEMENT).

Control set too warm Set control to a cooler setting (See OPERATION). Allow

Airflow to front grille blocked Airflow must not be obstructed to front grille (See

Dirty condenser coils Clean condenser (See MAINTENANCE; CONDENSER

Door gasket not sealing properly Door adjustment required (See MAINTENANCE; ADJUST

Item(s) interfering with drawer Reposition or remove item(s).

Inaccurate temperature reading Properly check temperature (See OPERATION).

Control set too cold Set control to a warmer setting (See OPERATION). Allow

humidity

Unit not level Make sure unit is level (See LEVELING, page 14).

24 hours for temperature to stabilize.

OPERATION).

CLEANING).

DRAWERS).

24 hours for temperature to stabilize.

Defrost unit manually (See MAINTENANCE;
DEFROSTING).

from the ice maker will be heard.

22 2275DWRWS, 2275DWRWOL

U-Line Corporation Limited Warranty

U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of
one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the
evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from
defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year
warranty period for all U-Line products U-Line shall: (1) at U-Lines option, repair any product or replace any part of a
product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the
United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with
the replacement of any defective part. During years two through five of the warranty period for the sealed system, U­Line shall: (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and
Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall
cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. All other
charges, including transportation charges for replacements under this warranty and labor costs not specifically covered
by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product.
The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you
can register on-line at www.U-LineService.com.

The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God,
such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation,
unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water
level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the
controls; door reversal; or cleaning the condenser.

If a product defect is discovered during the applicable warranty period, you must promptly notify either the dealer from
whom you purchased the product or U-Line at P.O. Box 245040, Milwaukee, Wisconsin 53224 or at 414-354-0300. In no
event shall such notification be received later than 30 days after the expiration of the applicable warranty period. U-Line
may require that defective parts be returned, at your expense, to U-Lines factory in Milwaukee, Wisconsin, for
inspection. Any action by you for breach of warranty must be commenced within one year after the expiration of the
applicable warranty period.

This limited warranty is in lieu of any other warranty, express or implied, including, but not limited to any
implied warranty of merchantability or fitness for a particular purpose; provided however, that to the
extent required by law, implied warranties are included but do not extend beyond the duration of the
express warranty first set forth above. U-Lines sole liability and your exclusive remedy under this warranty
is set forth in the initial paragraph above. U-Line shall have no liability whatsoever for any incidental,
consequential or special damages arising from the sale, use or installation of the product or from any other
cause whatsoever, whether based on warranty (express or implied) or otherwise based on contract, tort or
any other theory of liability.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.

2275DWRWS, 2275DWRWOL 23

For General Inquiries:

P.O. Box 245040
Milwaukee, Wisconsin
53224-9540 U.S.A.
Phone [phone]
FAX [phone]
www.U-Line.com

For Service and Parts
Assistance:

Phone [phone]
[phone]
FAX [phone]
Email:
[e-mail]
www.U-LineService.com
E-mail:
[e-mail]

For more than four decades, U-Line has distinguished itself as the

leader in built-in under-counter ice making, refrigeration and

wine storage appliances.

An INSTALLATION MANUAL for your unit, providing complete

installation information, is available for download at

www.U-Line.com. Information for custom panel inserts per model,

including panel size, and instructions are available by visiting

www.U-Line.com.

When you need replacement parts, always request genuine U-Line

replacements be used. Visit www.U-Line.com to locate a parts

distributor in your area.

U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in

undercounter ice makers, Combo

refrigerators, refrigerated drawers and refrigerator/freezers.

®

ice maker/refrigerators, Wine Captain® wine storage units,

©2006 U-Line Corporation
Publication No. 30179
01/2007 Rev. A