UHP UHP-1200 Installation Manual

Download

OUTDOOR SATELLITE ROUTER

UHP-1200

GENERAL DESCRIPTION AND INSTALLATION GUIDE

DOCUMENT RELEASE 3.2

[UHP.OR32.EN]

AUGUST 2015

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

CONTENT

Acronyms and Abbreviations .......................................................................................................... 4

Introduction ..................................................................................................................................... 6

Required level of qualification .................................................................................................................. 6

Document version and applicability .......................................................................................................... 6

Copyright ................................................................................................................................................... 6

1. General description .............................................................................................................. 7

1.1 System overview ....................................................................................................................... 7

1.2 Measurement equipment, tools and accessories .................................................................... 7

1.3 Labeling and sealing .................................................................................................................. 7

1.4 Packaging and content.............................................................................................................. 8

1.5 Description and principles of operation ................................................................................... 8

1.5.1 Overview ................................................................................................................................... 8

1.5.2 Power connector (DC IN) .......................................................................................................... 9

1.5.3 LAN interface connector ........................................................................................................... 9

1.5.4 IF Rx input ................................................................................................................................. 9

1.5.5 IF Tx Modulator output ............................................................................................................. 9

2. Operations .......................................................................................................................... 10

2.1 Operational limits ................................................................................................................... 10

2.2 Preparation for use ................................................................................................................. 10

2.2.1 Unpacking ............................................................................................................................... 10

2.2.2 Installation .............................................................................................................................. 10

2.2.3 Connecting to external devices .............................................................................................. 10

2.2.4 Powering on ............................................................................................................................ 11

2.2.5 Local access to router via HTTP interface ............................................................................... 11

2.2.6 Remote Telnet access ............................................................................................................. 11

2.2.7 Command Interface ................................................................................................................ 11

3. Operations .......................................................................................................................... 12

3.1 Software updates .................................................................................................................... 12

3.2 Powering off ........................................................................................................................... 12

3.3 Safety instructions for operations .......................................................................................... 12

4. Troubleshooting ................................................................................................................. 13

5. STORAGE, TRANSPORTATION AND DISPOSAL .................................................................... 15

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

FIGURES

Figure 1 Structure of UHP Manuals ............................................................................................................... 6

Figure 2 UHP-1200 Outdoor Satellite Router ................................................................................................ 7

Figure 3 Labeling of UHP-1200 satellite router ............................................................................................. 8

Figure 4 UHP-1200 Architecture ................................................................................................................... 8

Figure 5 UHP-1200 series modem – rear view .............................................................................................. 9

TABLES

Table 1 Operational limits ........................................................................................................................... 10

Table 2 Pinout of 8P8C LAN interface (RJ45) .............................................................................................. 10

Table 3 Troubleshooting guide .................................................................................................................... 13

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

ACRONYMS AND ABBREVIATIONS

16APSK

16 Amplitude and Phase-shift keying or Asymmetric Phase-shift keying, (APSK), is a digital modulation scheme that conveys data by changing, or modulating, both the amplitude and the phase of a reference signal (the carrier wave).

32APSK

32 Amplitude and Phase-shift keying or Asymmetric Phase-shift keying, (APSK), is a digital modulation scheme that conveys data by changing, or modulating, both the amplitude and the phase of a reference signal (the carrier wave).

8PSK

Phase-shift keying (PSK) is a digital modulation scheme that conveys data by changing, or modulating, the phase of a reference signal (the carrier wave).

AGC

Automatic Gain Control

BCH

BCH code is a multilevel cyclic variable-length digital error-correcting code used for correcting multiple random error patterns. BCH codes may also be used with multilevel phase-shift keying whenever the number of levels is a prime number or a power of a prime number.

BUC

Block Up-Converter (BUC) is used in the transmission (uplink) of satellite signals. It converts a band (or "block") of frequencies from a lower frequency to a higher frequency.

C/N

Carrier-to-noise ratio, often written as CNR or C/N, is the signal-to-noise ratio (SNR) of a modulated signal.

CRTP

Compressing IP/UDP/RTP Headers for Low-Speed Serial Links

DAMA

Demand Assigned Multiple Access. Channel establishment on demand.

DSCP

Differentiated Services Code Point (DSCP) is a 6-bit field in the header of IP packets for packet classification purposes. DSCP replaces the outdated IP precedence, a 3-bit field in the Type of Service byte of the IP header originally used to classify and prioritize types of traffic

DVB

Digital Video Broadcasting (DVB) is a suite of internationally accepted open standards for digital television.

Eb/No

Eb/N0 (the energy per bit to noise power spectral density ratio) is an important parameter in digital communication or data transmission. It is a normalized signal-to-noise ratio (SNR) measure, also known as the "SNR per bit". It is especially useful when comparing the bit error rate (BER) performance of different digital modulation schemes without taking bandwidth into account.

EIRP

Effective Isotropically Radiated Power

ETSI

The European Telecommunications Standards Institute (ETSI) is an independent, non-profit, standardization organization in the telecommunications industry (equipment makers and network operators) in Europe, with worldwide projection.

FEC

In telecommunication and information theory, forward error correction (FEC) is a system of error control for data transmission, whereby the sender adds redundant data to its messages, also known as an error-correction code.

Frame

TDMA service packet describing which station should transmit in which time slot . Generated ~10 times per second.

Hard priority

Method of transmission queues handling when packets from lower priority queue are not transmitted until all packets from higher priority queue are transmitted.

HTTP

Hypertext Transfer Protocol (HTTP) is an application-level protocol for distributed, collaborative, hypermedia information systems.

HUB

Central Station of satellite network that is managing all the terminals and resources

Hubless

Special mode of operation when all stations are transmitting to one TDMA carrier and all receiving this carrier.

Hardware

ICMP

The Internet Control Message Protocol (ICMP) is used by networked devices to send error messages—indicating, for instance, that a requested service is not available or that a host or router could not be reached.

IESS

Intelsat Earth Station Standards

IFL

Connection from the indoor equipment (modem/router) to the outdoor equipment at the antenna normally involves two inter-facility (IFL) cables.

IGMP

The Internet Group Management Protocol (IGMP) is a communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships.

Inroute

Channel from stations to hub.

IP is the usual abbreviation for Internet Protocol.

LDPC

Low-density parity-check (LDPC) code is a linear error correcting code, a method of transmitting a message over a noisy transmission channel, and is constructed using a sparse bipartite graph.

LNB

Low-noise block converter is the receiving converter installed at satellite antenna.

Local oscillator

Oscillator built into RF block converter ( BUC or LNB ). Value of LO is usually written on block enclosure or in datasheet.

Long frames

DVB-S2 frames 64800 bits long (including FEC). Require slightly lower C/N than short frames.

Master

Main station of Hubless network. Master allocates bandwidth and performs stations acquisition.

MCPC

Multiple channels per carrier. All TDM carriers generated by UHP can be treated as MCPC. Even if they are called SCPC.

Mesh

Capability of station allowing to receive other stations via TDMA link.

MF-TDMA

TDMA working on several RF channels simultaneously. All MF channels work as one aggregate TDMA channel.

MODCOD

Modulation and coding mode.

NMS

Network Management System

Node Station

Terminal of satellite network which is able to receive information directly from other network terminals

ODU

Out-Door Unit

Outroute

Forward TDM channel (MCPC) from HUB to stations.

QPSK

Phase-shift keying (PSK) is a digital modulation scheme that conveys data by changing, or modulating, the phase of a reference signal (the carrier wave).

RF level

Absolute RF level of entire signal (carrier + adjacent carriers) expressed in dBm.

RSV

Reed–Solomon error correction is an error-correcting code that works by oversampling a polynomial constructed from the data.

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

SCPC

Single Channel Per Carrier

Short frames

DVB-S2 frames 16200 bits long (including FEC). Advisable to use at lower symbol rates. Produce less delay than Long frames.

SNMP

Simple Network Management Protocol

SNTP

Simple Network Time Protocol (SNTP) is a protocol and software implementation for synchronizing the clocks of computer systems over packet-switched, variable-latency data networks.

SNR

Signal-to-noise ratio is an electrical engineering measurement defined as the ratio of a signal power to the noise power corrupting the signal.

Symbol Rate

Star

Type of network with one central station (hub) and several peripheral stations.

Software

TDM

Time Division Multiplexing

TDMA

Time Division Multiple Access

Telnet

Telecommunication Network (Telnet) is a network protocol used on the Internet or local area networks to provide a bidirectional interactive communications facility. Typically, telnet provides access to a command-line interface on a remote host via a virtual terminal connection.

Terminal

Earth Stations (usually VSAT) operated under management of network HUB

TFTP

Trivial File Transfer Protocol (TFTP) is a file transfer protocol, with the functionality of a very basic form of File Transfer Protocol (FTP).

Timestamp

Time format used by UHP. Plus sign at the beginning (+HH:MM:SS or +NN d HH:MM:SS)denotes relative time from some event or UHP start-up. If UHP has time synchronized to hub or SNTP absolute time can be displayed. Time zone affects absolute time.

Time-slot

Time interval for station transmission.

UDP

The User Datagram Protocol (UDP) is the set of network protocols used for the Internet. With UDP, computer applications can send messages, in this case referred to as datagram, to other hosts on an Internet Protocol (IP) network without requiring prior communications to set up special transmission channels or data paths.

USB

USB (Universal Serial Bus) is a specification to establish communication between devices and a host controller (usually personal computers).

VLAN

A virtual LAN, commonly known as a VLAN, is a group of hosts with a common set of requirements that communicate as if they were attached to the same broadcast domain, regardless of their physical location.

VoIP

Voice over Internet Protocol (VoIP) is a general term for a family of transmission technologies for delivery of voice communications over IP networks such as the Internet or other packet-switched networks.

VSAT

Very Small Aperture Terminal – satellite earth station with small-size antenna

WFQ

Weighted fair queuing. Method of proportional division of bandwidth between transmission queues.

X-modem

Simple file-transfer protocol

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

INTRODUCTION

This document presents a general description of the UHP-1200 series satellite routers and is intended for familiarization with the system capabilities and specifications. This manual is applicable to all the key modes of the router operations.

Required level of qualification

This manual is intended for engineering personnel operating VSAT networks. Such specialists should have adequate educational credentials in the field of electronics and sufficient experience and skills in data networks administration and satellite systems.

Document version and applicability

UHP VSAT platform is based on the universal satellite router UHP, which is available in different fully-compatible hardware modifications. UHP satellite router is a basic element of any network architecture and can be used in any combinations and at any hierarchy level. Router functional capabilities and its operating modes are determined by the installed software and its configuration.

This manual is applicable to all UHP-1200 series outdoor satellite routers (previously known also as UHP-1000-OD) with software release 3.2 or higher. When ordering this document, please specify its ID: [UHP.OR32.EN].

Figure 1 Structure of UHP Manuals

The content of this document is the intellectual property of UHP Networks Inc. (referred to below as UHP Networks). Copying or quoting this description as a whole or of any part of it without a written permission from UHP Networks is prohibited.

Network

Engineering

TDM/TDMA

Terminal

SCPC

Modem

Hubless

TDMA

Station

UHP-1200

UHP-8000

UHP-200

UHP-IFS

NMS

System Level

(Network engineering guide)

Hardware Level

(Installation guide and specifications)

Service Level

(User manual)

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

1. GENERAL DESCRIPTION

1.1 System overview

UHP satellite routers are essentially a universal solution for geographically distributed VSAT-class satellite communication networks. UHP routers can be used to organize simple point-to-point channels, “star”- and “mesh”-topology networks with several hierarchy levels and bandwidth-on-demand capabilities.

UHP VSAT platform is based on many innovation technologies. It was developed using long-term experience in satellite service provisioning. Nowadays electronics achievements made it possible to make VSAT platform compact and assure its efficiency and reach functionality.

Weatherproof UHP-1200 satellite router can be installed outdoors, for example, directly on the antenna. IP67 design ensures reliable operation over a wide temperature range.

Figure 2 UHP-1200 Outdoor Satellite Router

Technical characteristics are given in the appropriate product specification sheets.

1.2 Measurement equipment, tools and accessories

The router can be accessed via LAN. Standard computer (notebook) is required to configure and monitor status of UHP-1200 satellite router. The computer must be equipped with a LAN interface, and also have the following software installed:

 Internet browser (WEB browser)  Telnet Client (optional)  The Terminal (e.g.: Hyperterminal, included in the OS Windows) (optional)

1.3 Labeling and sealing

The product is marked with the unique Serial Number, as well as Part Number on the bottom of the router case.

The warranty seals are located on the bottom of the product, at the junction of the two parts of the case. Product warranty will automatically void if such labels have been removed, modified or damaged.

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

Figure 3 Labeling of UHP-1200 satellite router

1.4 Packaging and content

Standard UHP-1200 package includes:

1. Satellite router UHP-1200;

2. Installation kit.

It is recommended to keep original packaging throughout the entire lifetime. Conservation, storage and transportation of the terminal must be in original packaging.

1.5 Description and principles of operation

Figure 4 UHP-1200 Architecture

1.5.1 Overview

UHP-1200 Satellite router has a weatherproof, sealed housing and without any serviceable parts inside. External devices should be connected through connectors on the bottom interface of the device. The

LAN port is used both for connection to the user’s network and for configuration and control of the

router.

UHP-1100

Router board

TDMA Rx

MCPC Rx

LAN

IF Splitter

IF Tx

DC IN

IF Rx

LAN

DC IN

UHP-1200

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

Figure 5 UHP-1200 series modem – rear view

1.5.2 Power connector (DC IN)

UHP-1200 router is powered with 24 VDC. AC/DC Power supply adaptor is not supplied. The router can be powered from different DC power sources (batteries, DC-DC converter). The router can provide power to RF hardware within the current according to the specifications of the router.

1.5.3 LAN interface connector

LAN connector is purposed for connecting to Ethernet switch using a straight cable. Bit rate 10 or 100 and duplex mode are software selectable.

1.5.4 IF Rx input

This interface is intended to connect the router to the LNB. The received signal via the built-in splitter (see Figure

4) is fed to a DVB and TDMA demodulators of the router. The input, on the router side, can be fed with 18 VDC power supply. Whether power source in on or off, the input can withstand external voltage up to 50 VDC (power supply circuit is provided with a diode). Power supply circuit is protected with a thermal fuse operating in case of short circuiting. After short circuiting is removed it may be required to disconnect load from Rx inputs for several seconds so as to allow the fuse to return to its initial state. Cable length and cable quality (losses level) can affect the quality and possibility of receiving signals.

THE TOTAL CURRENT CONSUMED BY EXTERNAL EQUIPMENT THROUGH BOTH RX INPUTS SHOULD NOT BE IN EXCESS OF 750 MA. NORMALLY, CURRENT CONSUMPTION BY DRO LNB - 150 MА, PLL LNB - 500 MА.

1.5.5 IF Tx Modulator output

IF TX OUTPUT CAN FEATURE 24 VDC WITH A HIGH SHORT-CIRCUIT CURRENT. SHORT CIRCUITING CAN CAUSE SPARKLE

SPREAD AND BURNS. THIS VOLTAGE CAN DAMAGE MEASUREMENT EQUIPMENT IF IT IS NOT PROTECTED AT ITS INPUTS.

SUPPLYING EXTERNAL VOLTAGE TO THIS CONNECTOR IS OBJECTIONABLE AND SUPPLYING MORE THAN 24 V IS

PROHIBITED.

UHP-1200 modulator is compatible with most satellite transmitters/converters (BUC). Modulator is connected directly to the IF Tx connector. The router provides 24 VDC power supply to the BUC and 10 MHz reference signal. UHP-1200 is not provided with a separate protection on the transmitter power supply circuitry. Use is made of current protection for the power supply adapter. In case of a short circuit the router is de-energized and then gets restarted. If power supply is switched on in the configuration, restarts continue at 5 seconds interval until short circuiting is removed.

ANY OPERATIONS WITH IF TX CABLE SHOULD BE PERFORMED WITH 24 V SUPPLY VOLTAGE TURNED OFF. OTHERWISE,

SELF-INDUCTION ACROSS A LONG CABLE CAN DAMAGE THE TRANSMITTER AND/OR THE ROUTER.

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

2. OPERATIONS

2.1 Operational limits

Table 1 Operational limits

Parameter

Limits

Minimum

Maximum

Router DC Input voltage

23 VDC

25 VDC

Output current at Tx Out interface

2 A

Input voltage on the Tx Out interface

24 V

Output current at Rх SCPC or RX TDMA

0,75 А

Input voltage on other interfaces

18 V

Operational temperature

0 С

+40 0C

Relative humidity (@ 250С)

90%

Atmospheric pressure (mm Hg)

720

770

Mechanical impacts (acceleration with an amplitude not exceeding 1,25 mm):

- in a range 0,5 – 15 Hz:

- in a range 15-40 Hz:

- in a range 40-300 Hz:

2,45 m/s 5,88 m/s 14,7 m/s

2.2 Preparation for use

2.2.1 Unpacking

Before opening the packaging please check a safety of transport container. If there is any visible damage of packaging you should keep it as long as the delivered equipment will be properly tested.

2.2.2 Installation

UHP-1200 Router is designed for installation on any flat, stable surface or on an antenna mount with the included universal installation kit. The router should be installed in a place protected from direct sunlight.

Table 2 Pinout of 8P8C LAN interface (RJ45)

Пин

Назначение

Rx +

Rx -

Tx+

DC +

Tx -

DC -

2.2.3 Connecting to external devices

All wire connections must be performed before powering up the router. Cable connectors should be screwed to the router without use of any mechanical instruments. Please, avoid excessive force when connecting IF cables.

WARNING! DO NOT CONNECT OR DISCONNECT ANY CONNECTING CABLES TO THE ROUTER WITH THE POWER ON. THIS

CAN LEAD TO A FAILURE OF THE ROUTER AND CONNECTED DEVICES.

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

2.2.4 Powering on

In a few seconds after powering the router it is ready for use. The actual status of the router can be checked using its web interface (via LAN). With factory setting the router is configured as TDM/TDMA terminal. The router requires change of mode of operation (if necessary) and/or configuration of respective network parameters before login into satellite networks. The easiest way to configure the router is using its HTTP access via its LAN port.

The router can be reset by short (2-3 sec.) power interruption.

2.2.5 Local access to router via HTTP interface

HTTP (web) interface allows configuration key parameters and monitoring its actual status of the router. Local Web page of the router can be accessed from any Internet browser.

By default, UHP-1200 router is configured with IP-address 192.168.222.222 with mask 255.255.255.248 (/29). Respectively, the computer should be configured with an address, e.g. 192.168.222.217 with the same mask.

In case the satellite routers have been preconfigured at the factory on customer’s request such routers may have different default IP address. In such case the respective IP addresses will be listed in the passport of the router. If it’s impossible connecting the router with any of specified addressed please reset the router to factory settings.

2.2.6 Remote Telnet access

Remote access to the configuration can be performed using Telnet protocol. The connection can be provided to any of IP addresses that are set on the router. UHP-1200 supports simultaneously only one Telnet session. In order the hang session does not block access to the device forever in case on non-activity (pressing ENTER key), the router auto-terminates the session after a certain time of inactivity. The time can be set in the configuration, and by default it is 10 minutes.

2.2.7 Command Interface

Please refer to the Command Interface manual applicable for the respective version of SW and activated mode of operation of the UHP router. The Command Interface manuals are available for download and online use on the website: http://www.uhp.net.

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

3. OPERATIONS

UHP Routers belong to the class of unattended equipment and during its operation does not require any special staff exploitation. When operated as SCPC station or TDM/TDMA terminal the satellite router does not require any changes of settings or it is configured remotely from the Hub. The tasks of operational staff are limited to the following:

 Monitoring of climatic environment of operation, ensuring the absence of dust, preventing the ingress of

moisture on the surface of the device. Should provide unrestricted air access to router for cooling.

 Cables connected to the device must not suffer any significant impact on the connections of the router.

All connectors must be properly attached and secured.

3.1 Software updates

One of the key advantages of UHP satellite routers is the ability to extend the functionality by updating the software. Software updates also include fixes for known bugs and improving the algorithms of the system.

3.2 Powering off

The router can be powered off by disconnecting its DC cord from the power supply.

3.3 Safety instructions for operations

 Connect and disconnect any cables only when router is powers off;  The router must have a reliable grounding;  Do not try to repair the router and not use it for other purposes;  There no serviceable components inside, opening a housing is not permitted;  Servicing by qualified personnel only.

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

4. TROUBLESHOOTING

Table 3 Troubleshooting guide

Symptoms

Possible reasons

Actions

Router doesn’t work

DC power beyond the limits of allowed values

Check DC power voltage

Power cord is broken

Check the power cable and output voltage. Replace a cable.

Router restarts every 3-5 seconds.

Short-circuit in transmit cable

Disconnect and check Tx cable

Software failure

Reset software to factory defaults

No reception from the satellite (indicator LOCK is off, single flashes of ERROR indicator)

Incorrect configuration

Check Rx frequency and symbol rate.

IF cable failure

Check Rx cable and make sure that its connectors are properly connected to the LNB and the router.

LNB is not powered

Check if LNB power is switched on Disconnect Rx IF cable from LNB and make sure that 12-18 VDC is available on the connector. Check Rx level in the statistic of the demodulator.

No carrier on the satellite or its level is insufficient.

Verify availability of the carrier and its level with spectrum analyzer. Contact Hub administrator and investigate if the carrier is properly transmitting and local weather conditions not attenuate the signal.

Low Rx carrier level

Measure carrier signal to noise level with a spectrum analyzer. Verify if antenna is properly pointed to the satellite and there no obstacles in the direction to the satellite.

Check the integrity of the film of antenna’s feed

horn and absence of moisture in it.

LNB failure

Replace LNB to the spare one

High rate of errors of Rx path

Bad weather conditions

The quality of reception may temporary decrease during intensive rainfall, for, thunderstorm cloudiness. Check if there is no snow or ice on the antenna surface and on the feed horn.

Low signal to noise level

Check C/N in demodulator’s statistics. Verify if antenna is properly pointed to the satellite and there no obstacles in the direction to the satellite.

Check the integrity of the film of antenna’s feed

horn and absence of moisture in it.

Low Rx carrier level Interferences

Check Eb/No in demodulator’s statistics. Contact Hub administrator and investigate if the carrier is properly transmitting and local weather conditions not attenuate the signal

Station is not transmitting

Wrong network setting

Check Tx frequency and symbol rate of the modulator. Make sure that transmission is enabled

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

Symptoms

Possible reasons

Actions

Transmission of the terminal is not allowed by Hub (only for TDM/TDMA terminal)

Contact Hub administrator

Station is not transmitting

IF Tx cable failure

Check Tx cable and make sure that its connectors are properly connected to the BUC and the router.

BUC is not powered

Check if BUC power is switched on Disconnect Tx IF cable from BUC and make sure that 24 VDC is available on the connector.

BUC failure

Replace the BUC on the spare one

Other symptoms

Other reasons

Contact your dealer or service center

In many cases, reinstalling system software allows to restore a satellite router functionality, which may need reset to the factory default configuration.

If the recovery of software cannot be implemented successfully, or if this operation does not eliminate the defect, it is necessary to illuminate the faulty device and replace it by new device.

UHP-1200 OUTDOOR SATELLITE ROUTER

GENERAL DESCRIPTION AND INSTALLATION GUIDE, v3.2

5. STORAGE, TRANSPORTATION AND DISPOSAL

Storage and transportation of satellite routers must be performed in original packaging. Equipment can be stored and transported in pallet with height not more than 10 devices.

Storage and transportation should comply with the following conditions:

 - limiting low temperature of storage (minus 40 ± 2) ° C;  - limiting high temperature of storage (50 ± 2) ° C.  - atmospheric pressure 720 ÷ 770 mm. Hg.

Utilization of satellite routers must be in accordance with the rules for disposal of industrial or consumer electronics in accordance with applicable law.

UHP UHP-1200 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual