KMIRP2®
INSTRUCTION MANUAL
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Switch the printer on.
NOTE: The printer will automatically switch off after 10 minutes of
i n a c t i v i ty. To reactivate simply press the power on button. The printer
will also switch off automatically during printing if the battery voltage
d r ops too low. If this happens install a new set off batteries.
Positioning the Printer and Instrument
Ensure that there are no obstructions between the instrument emitter (at
the top of the unit) and the Printer Receiver (on the bottom of the printer
b e l ow the keypad).
• Maximum distance < 15 feet
Self-Test and Battery Condition Indication
To run the printer self-test and battery indication, follow these steps:
1. With instrument off, press and hold paper feed button
(up arrow)
2. Press and release power-on button
3. Release paper feed button
The printer will display “STA R T TEST” and will then print all available
c h a r acters. At the bottom of the characters the battery level will be
i n d i c ated by a value between a low of 1 and a high of 5, for example
“BAT : 5 ”. The last line of the display will indicate “END TEST” .
Regardless of the battery condition reference, new batteries should
be installed when any of the following symptoms are present:
• The print contrast remains too low, even when the control is
set to highest contrast
• Print speed slows due to the print head moving too slowly
across the paper
• Printing stops before all information on a line has
been completed
• The battery condition reference (shown at the end of the
self-test) is 1 or 0
Contrast Adjustments
The printers contrast (image clarity) can be adjusted using the left or right
keys. Use the left key to lighten the image and the right key to darken the
image. Use the lightest acceptable contrast setting to ensure the longest
possible battery life. if the contrast cannot be set to an acceptable level,
change the batteries.
Battery Life
For longest battery life, always turn off the printer when printing is
complete. To help prevent potential damage from leakage, remove
the batteries if the printer will not be used for a long period of time.
Optional AC Adapter
In order to prolong the battery life, the printer will also operate with an
optional AC Adapter (KMCU/IRP220).
Introduction
The KMIRP2 printer allows a user to obtain a hard copy of information
held on their analyzer by utilizing the infrared printer port.
Features include
• New compact design with a protective rubber boot
• Integrated magnet in the back of the rubber boot for
on-demand hands-free printing
• Infrared port receives readings up to 15’ away without
losing connection. Allowed 60˚ angle up to 10” away
• Communicates with UEi analyzers and other analyzers
using HP protocols
• Self-test and battery condition indication
• Auto power off
• Paper advance
C o n t rols and Indicators
1. : ON/OFF
2. : Paper feed
3. : Lighten contrast
4. : Darken contrast
Operating Instructions
Set Up
The printer is powered by 4 “AA” size alkaline batteries which will provide
around 6000 print lines before replacement is required. Batteries should
be fitted into the battery compartment on the rear of the printer, taking
note of the individual battery orientation.
The KMIRP2 uses thermal paper and care should be taken when fitting
n ew paper rolls to ensure that the “shiny” side of the paper faces the
print head. The paper should be placed into the slot within the paper roll
holder while holding the paper feed button until the paper feeds through
to the front of the printer. Ensure that the paper has an even edge and is
not folded before attempting to load into the printer.
WARNING!
Do not try and pull the paper through manually as this could damage
the print head. If the paper jams, use the paper feed button, very
carefully ease the edge of the paper back into the paper roll holder
and try reloading as detailed above.
KMIRP2-MAN P. 1
1
3
4
2
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Controlling The Print Head
If you turn the printer off while printing, the print head may stop in the
middle of the line. To return the print head to the left side of the paper,
turn the printer on, then off.
Missing or Misformed Characters
The “_” or “ “ character will show on the print out if the printer has
detected incorrect data due to interference with, or interruption to, the
stream of incoming information.
Common causes for this error include incorrect positioning of, or
distance to printer with reference to the instrument. Obstruction of
the infrared signal or even interference from another infrared emitting
source can also affect the printout.
Environmental Limits
KMIRP2-MAN P. 2
Operating temperature: 32˚ to 122˚F (0˚ to 50˚C)
Storage temperature: -40˚ to 140˚F (-40˚ to 60˚C)
Humidity: 5% to 95% relative at 104˚F (40˚C)
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Limited Warranty
The KMIRP2 is warranted to be free from defects in materials and workmanship for a period
of one year from the date of purchase. If within the warra n ty period your instrument should
become inoperative from such defects, the unit will be repaired or replaced at UEi’s option.
This warra n ty covers normal use and does not cover damage which occurs in shipment or
failure which results from alteration, tampering, accident, misuse, abuse, neglect or improper
maintenance. Batteries and consequential damage resulting from failed batteries are not
covered by warra n ty.
Any implied warranties, including but not limited to implied warranties of merchantability
and fitness for a particular purpose, are limited to the express warranty. UEi shall not be
liable for loss of use of the instrument or other incidental or consequential damages,
expenses, or economic loss, or for any claim or claims for such damage, expenses or
economic loss. A purchase receipt or other proof
of original purchase date will be required
before warra n ty repairs will be rendered. Instruments out of warra n ty will be repaired (when
r e p a i r able) for a service charge. Return the unit postage paid and insured to:
This warranty gives you specific legal rights. You may also have other rights which vary from
state to state.
KMIRP2
Infrared Thermal Printer
®
Copyright © 2004 UEi KMIRP2-MAN 11/04
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...