UEi Test Instruments DL489COMBO User manual

DL489
Commemorative Edition True RMS Digital Clamp-On Meter
INSTRUCTION MANUAL
ENGLISH
CAT III
600V 600A
600V
CAT I II
1000V
CAT I I
NCV
μ
V
MAX/
H
z
MIN
PEAK
DL489
T
e
A
m
p
/
A
°
F
°
C
MFD
/
D
u
t
y
True RMS
T1
T2
CATII 1000V
CATIII 600V
MAX
RANGE
INRUSH
TEMP
Zero
DC
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
TABLE OF CONTENTS
FEATURES .............................................................................................3
GENERAL SPECIFICATIONS
IMPORTANT SAFETY WARNINGS
CATEGORY DEFINITIONS
SYMBOLS .............................................................................................5
OVERVIEW
OPERATING INSTRUCTIONS
AC Amps: < 600A – Jaw ......................................................... 7
DC Amps: <600A – Jaw ............................................................8
Non-Contact Voltage ..................................................................8
Zero DC Amps ..............................................................................9
AC/DC Low Amps: <2000μA .......................................................9
Temperature F˚/C˚ .....................................................................10
Continuity ..................................................................................10
Resistance: < 60MΩ .................................................................11
Capacitance (MFD).....................................................................11
Diode .........................................................................................12
Min/Max/Peak ...........................................................................12
Voltage: AC 750V / DC 1000V ................................................ 13
Frequency (Hz) / Duty Cycle ......................................................14
Battery Replacement ................................................................ 14
LRA Inrush ..................................................................................15
Test Lead Notes .........................................................................15
WARRANTY .........................................................................................16
DISPOSAL
CLEANING
STORAGE
..................................................................................... 5 - 7
...........................................................................................16
...........................................................................................16
...........................................................................................16
.............................................................3
............................................ 3 - 4
...................................................................4
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
FEATURES
• True RMS
• 600A AC/DC
• 750V AC/1000V DC
• Resistance 60MΩ
• Capacitance 2000μF
• AC/DC microamps 2000μA
• Frequency 99.99kHz
• Dual Temperature Differential
• Non-Contact Voltage
• LRA Inrush
• Data hold
• Min/Max
• Peak hold
• Visible high-voltage alert
• Manual ranging option
• Worklight/ back lit display
• Low battery indicator
• Auto power off
• Magnetic mount
• Dual display
• Input jack locks
• Detachable clamp head
GENERAL SPECIFICATIONS
• Operating Temperature: 32˚ to 122˚F (0˚ to 50˚C)
• Storage Temperature -4˚F to 140˚F (-20˚ to 60˚C)
• Operating Humidity: <80%
• Operating Altitude: 6,562 ft (2,000m)
• Pollution Degree: 2
• Display: 3 5/6 digits, 6,000 count
• Refresh Rate: 3/sec
• Over-range: “OL” is displayed
• Dimensions: 10.2” X 2.5” X 1.5”
• Item Weight: 1 lb.
• Calibration: Recommended annually
• CAT Rating: CAT III 600V/CAT II 1000V
• Certifications: cETLus 3rd Edition, CE Conformity, IEC 61010-1 3rd Edition, IP42, 6’ Drop Protetion, RoHS,
• Battery Type: (AAA) X 6
• Test Leads: Test leads w/alligator clips CATIV 600V/CATII 1000V
IMPORTANT SAFETY WARNINGS
WARNING
Read entire Safety Notes section regarding potential hazard and proper instructions before using this meter. In this manual the word “WARNING” is used to indicate conditions or actions that may pose physical hazards to the user. The word “CAUTION” is used to indicate conditions or actions that may damage this instrument.
WARNING
To ensure safe operation and service of the tester, follow these instructions. Failure to observe these warnings can result in severe injury or death.
WARNING
• Before each use, verify meter operation by measuring a known voltage or current.
• Never use the meter on a circuit with voltages that exceed the category based rating of this meter.
• Do not use this meter during electrical storms or in wet weather.
• Do not use the meter or test leads if they appear damaged.
• Ensure meter leads are fully seated and keep fingers away from the metal probe contact when making measurements. Always grip the leads behind the finger guards molded into the probe.
• Do not open the meter to replace batteries while the probes are connected.
3
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
IMPORTANT SAFETY WARNINGS (CONT.)
• Use caution when working with voltages above 60V DC or 25V AC RMS. Such voltages pose shock hazards.
• To avoid false readings that can lead to electrical shock, replace batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lockout power before measuring resistance or capacitance.
• Always adhere to national and local safety codes. Use proper personal protective equipment (PPE) to prevent shock and arc blast injury where hazardous live conductors are exposed.
• Always turn off power to a circuit or assembly under test before cutting, unsoldering or breaking the current path. Even small amounts of current can be dangerous.
• Always disconnect the live test lead before disconnecting the common test lead from the circuit.
• In the event of electrical shock, ALWAYS bring the victim to the emergency room for evaluation, regardless of victim’s apparent recovery.
Electrical shock can cause unstable heart rhythms that may need medical attention.
• If any of the following occurs during testing, turn off the power source to the circuit being tested: arcing, flame, smoke, extreme heat, smell of burning materials or discoloration melting of components.
WARNING
Higher voltages and currents require greater awareness of physical safety hazards. Before connecting the test leads, turn off power to the circuit under test, set meter to the desired function and range, connect the test leads to the meter first, then connect to the circuit under test. Reapply power. If an erroneous reading is observed, disconnect power immediately and recheck all settings and connections.
WARNING
This meter is designed for trade professionals who are familiar with the hazards of their trade. Observe all recommended safety procedures that include proper lock-out utilization and use of personal protective equipment that includes safety glasses, gloves and flame resistant clothing.
CATEGORY DEFINITIONS
Measurement
Category
II < 10 Circuits connected to mains socket
III
IV > 50 Source of the mains installation in the
Short-Curcuit
(typical) kA
a
outlets and similar points in the MAINS installation
< 50 Mains distributions parts of the building
building
Location in the
building installation
4
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
SYMBOLS
AC (Alternating current) DC (Direct current)
Negative DC AC/DC Voltage or Current
Auto-ranging
Auto power off Active Non-Contact Voltage
Low Battery Hold/Capture Value
Minimum measured value displayed
Duty Cycle Hertz/Frequency
Voltage
Ohms/Resistance Diode
Capacitance mode in nanofarads or microfarads
Degrees Fahrenheit Degrees Celsius
Continuity Mega (x106 or 1,000,000)
Milli (x10-3 or 0.001) Kilo (x103 or 1,000)
Nano (x10-9 or 0.000000001)
Microamps Warning or Caution
Ground Dangerous Levels
Double Insulation (Protection to Class II)
Overload: Range Exceeded
Maximum measured value displayed
Amperage
Microfarad
μF
Micro (x10-6 or 0.000001)
Safe for disconnect from live conductors
OVERVIEW
C
A
600V 600A
NCV
A
μ
V
MAX/
H
z
/
D
MIN
PEAK
DL489
CATII 1000V
B
CAT III
T
e
A
m
p
/
°
F
°
C
MFD
u
t
y
True RMS
T1
30V
T2
CATIII 600V
MAX
TEMP
INRUSH
D G
J
RANGE
DC
Zero
M N O R
X
Y
S
U
W
Z
S/N
V
5
E
F
H
I K
L
P
Q
T
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
OVERVIEW (CONT.)
A. Clamp: Measure inductive AC/DC current. Opens to 1.25” (31.7mm). B. Conductor Alignment Marks: Use to aid the visual alignment of a conductor
when measuring inductive amperage. Greatest accuracy is achieved when the conductor inside the clamp is centered at the intersection of these marks. C. Wire Separation Tab/ NCV sensor: Use to isolate an individual wire from a bundle for testing. NCV sensor detects live voltage.
D. Test Lead Holder: Used for hands-free use of the test probes. E. Worklight: Lights clamp area in dark work environments. F. Category Max Indicator: Maximum CAT Rating for clamp jaw. G. Hand Guide: Used as a point of reference for the operator’s safety. H. Clamp Lever: Opens and closes current clamp jaw.
NOTE: The clamp uses a high-tension spring to close the jaw. Do not allow fingers or objects to become pinched in the base as the jaws close.
I. NCV Alert Light: Indicates voltage when in NCV mode and high-voltage alert. J. Hold/Worklight/ Back light Button:
• Press to hold the reading on the display. Press again to return to live reading.
• Press and hold to turn on Worklight and Back light. Press and hold again to turn off.
• Worklight and Backlight turn off after 60 seconds.
K. NCV Button: Press and hold for Non-contact voltage detection mode. L. AC/DC Amps/ Microamps Button:
• Press to enter AC/DC Amps mode; (AC/DC Amps upper display)
• Press again to enter AC/DC Microamps (μA) mode; (AC/DC microamps lower display),
M. Temperature Button:
• Press to enter temperature mode for T1 (upper temperature input jack).
• Press again to enter temperature mode for T2 (lower temperature input jack).
• Press again to enter temperature differential mode (T1-T2).
• Press and hold to change temperature scale.
N. Range Button:
• Press to toggle to between Auto and Manual Ranging modes. (AT will appear on display when in Auto Ranging mode).
• Press repeatedly to cycle through manual ranges when in Manual Ranging mode.
• Press and hold to return to auto ranging mode. Note: Select range prior to MIN/MAX for best results.
O. Power Button: Press to turn on and off the meter. P. Min/Max/ Peak Button:
• Press to enter Min/Max mode. Max is the default setting.
• Press repeatedly to cycle through Min/Max captured values.
• Press and hold to return to live readings.
• Press and hold to enter Peak mode.
• Press and hold again to return to live readings.
Q. AC/DC Volts/ Hertz (Hz)/ Duty Cycle Button:
• Press to enter AC Voltage mode.
• Press again to enter DC Voltage mode.
• Press and hold to enter Hertz (Hz)/Duty Cycle modes.
• Press to return to live readings.
R. Continuity/ Resistance/ Capacitance/ Diode Test Button:
• Press to enter Continuity mode.
• Press again to enter Resistance mode.
• Press again to enter Capacitance mode.
• Press again to enter Diode test mode.
• Press again to return to live readings.
6
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
S. DC Zero/ Inrush Button:
• Press to Zero the DC clamp reading.
• Press and hold to enter LRA Inrush mode (must be in AC amp mode first).
• Press and hold again to return to live readings.
T. Display:
• High contrast dual backlit display.
• Amps (AC/DC) reading will always display on upper display.
U. K-Type Temperature Probe Inputs: T1 (Upper) and T2 (Lower) V: Input Jack Lock: Switch to use Temperature or Test lead inputs W. Category Max Indicator: Maximum CAT Rating for input jacks.
• Multifunction Input Port: Used for measuring: AC or DC volts, resistance, continuity, diode, capacitance, AC or DC amps, AC or DC μA or LRA Inrush.
• Use CATIII test leads or higher
X. Magnetic Mount: For hands-free work. Y. Battery Cover: Easy access for replacing batteries without breaking
calibration seal.
Z. Serial Number
Apo: Auto power off after 30 minutes of use. Detachable Clamp Head: Compatible with industry standard meter heads. ADP
will appear on display. Press DC Zero to zero the head reading.
AC Amps: < 600A – Jaw
Single Conductor
CAT III
600V 600A
Only
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True RMS
T1
T2
CATII 1000V
CATIII 600V
MAX
30V
TEMP
• Default = (upper)
• Press x1 = (lower)
• Press x2 = (lower)
μA μA
• Press and hold =
• Center wire in guides for best accuracy.
• Opposing currents cancel each other (use line-splitter when necessary).
• Keep hands below guard when measuring high current levels.
• Do not attempt to measure more than 600A AC.
• 45Hz to 400Hz True RMS
• Minimum current for Clamp measurement: 0.3A
Features:
RANGE
HOLD
MAX/ MIN
PEAK
Range Resolution Accuracy Overload Protection
60A 0.01A 600A 0.1A
±(2.0% +8 dgts) 600V RMS
Minimum current for Clamp measurement: 0.3A
7
(upper)
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
DC Amps: <600A – Jaw
Single
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489 True RMS
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
• Do not attempt to measure more than 600A DC.
Features:
RANGE
HOLD
MAX/ MIN
PEAK
Range Resolution Accuracy Overload Protection
60A 0.01A 600A 0.1A
±(2.0% +8 dgts) 600V RMS
Minimum current for Clamp measurement: 0.3A
Conductor Only
• Default =
• Press x1 = (lower)
• Press x2 = (lower)
• Press and hold =
(upper)
μA μA
(upper)
Non-Contact Voltage
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True R MS
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
NCV Sensor in the tip.
• Press and hold the NCV button and move the tip of the clamp meter near voltage source.
• Non-Contact Voltage Detection is used to detect power with sensor located in the tip of the clamp head, indicates positive response with both an Audible and Visual alert.
• Do not use Non-contact voltage detector to determine if there is current on the wire. Detection operation could be affected by socket design, insulation thickness, type or other factors.
• Voltage indictor light may also light when voltage (>AC/DC 30V) is present on the meter’s input jack or from an external interference such as motors, flashlights, etc.
On Voltage
Approx. 24V AC
MAX
8
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Zero DC Amps
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True RMS
• Default = DC Zero
• Press and Hold = LRA Inrush
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
Select DC current.
• Press to zero any offset in Amps DC.
• Used to monitor change from present displayed value.
• Required during DC Amps measurement to establish a zero level.
WARNING
Do not use DC Zero mode at amps greater than 600A DC or 2000μA DC.
AC/DC Low Amps: <2000μA
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
MAX/ MIN
PEAK
DL489
V
H
z
/
D
u
CATII 1000V
MFD
t
y
True RMS
T1
30V
T2
CATIII 600V
MAX
C
DC Zero
INRUSH
TEMP
• Default = (upper)
• Press x1 = (lower)
• Press x2 = (lower)
μA μA
• Press and hold =
WARNING
• Do not attempt to measure more than 2000μA.
Features:
RANGE
HOLD
MAX/ MIN
PEAK
Range Resolution Accuracy Overload Protection
600μA 0.1μA 2000μA 1μA
± (1.2% +3 dgts) 600V RMS
True RMS: 45Hz to 400Hz
9
(upper)
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Temperature F˚/C˚
CAT III
600V 600A
T
e
m
p
/
°
F
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True RMS
T1
TEMP
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
Range Resolution Accuracy Overload Protection
-328˚F to 999˚F (-200˚ to 999˚C)
1000˚F to 2462˚F (1000˚ to 1350˚C)
0.1°F (0.1˚C)
1°F (1˚C)
±(1.0% +3.6˚F) ±(1.0% + 2.0˚C)
• Disconnect test lead probes from voltage source and meter.
• Move Input Jack Locks to “TEMP” setting.
• Use K-Type thermocouple temperature probes only.
• Stated accuracy does not account for themocople accuaracy.
Features:
HOLD
MAX/ MIN
PEAK
°
C
• Default = T1
• Press x1 = T2
• Press x2 = T1-T2
• Press and hold =
30V RMS
Continuity
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True RMS
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
• Buzzer sounds at less than < 40Ω.
WARNING
• Do not measure resistance on a live circuit.
Features:
MAX/ MIN
PEAK
HOLD
Open Circuit V <1.00V Overload Protection
Threshold Appox. <40Ω 600V RMS
10
• Default =
• Press x1 =
• Press x2 =
• Press x3 =
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Resistance: < 60MΩ
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
MAX/ MIN
PEAK
DL489
V
H
z
/
D
u
t
y
True RM S
DC
MFD
Zero
INRUSH
• Default =
• Press x1 =
• Press x2 =
• Press x3 =
Features:
RANGE
HOLD
MAX/ MIN
PEAK
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
Range Resolution Accuracy Overload Protection
600Ω 0.1Ω 6kΩ 1Ω 60kΩ 10Ω 600kΩ 100Ω
± (0.8% +3 dgts)
600V RMS
6MΩ 1kΩ 60MΩ 0.01MΩ ± (1.2% +3 dgts)
Capacitance (MFD)
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
MIN
PEAK
DL489
/
D
u
t
y
True RMS
Zero
INRUSH
• Default =
• Press x1 =
• Press x2 =
• Press x3 =
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
Features:
RANGE
HOLD
MAX/ MIN
PEAK
MAX
Range Resolution Accuracy Overload Protection
10.00nF
100.0nF
1.000μF
10.00μF
100.0μF
2000μF
0.01nF
0.1nF
0.001μF
0.01μF
0.1μF
1μF
± (3.0% +5 dgts) 600V RMS
11
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
GOOD DIODE
Reverse Bias
Displays "OL"
Forward Bias
Displays approx. voltage drop
BAD DIODE
600V 600A
NCV
V
MAX/
H
MIN
PEAK
DL489
Diode
CAT III
T
e
A
m
p
/
A
°
μ
F
°
C
MFD
z
/
D
u
t
y
True RMS
T1
30V
T2
CATII 1000V
CATIII 600V
MAX
• Default =
• Press x1 =
• Press x2 =
• Press x3 =
RANGE
DC
Zero
INRUSH
TEMP
Open Diode
Displays "OL"
or
Both directions
• Forward voltage drop if forward biased.
• “O.L.” if reverse biased.
Features:
MAX/ MIN
PEAK
HOLD
Diode Test
Range Open Circuit V Test Current Overload Protection
3.0V <3.2V DC 0.25mA 600V RMS
'0' Both directions
Min/Max/Peak
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True RMS
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
12
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Voltage: AC 750V / DC 1000V
CAT III
600V 600A
High Voltage Alert
WARNING
• Use CATIII rated test leads or higher.
• Do not attempt to measure more than 750V AC/1000V DC.
• Keep hands below line when measuring high current levels.
• Do not exceed 25 volts AC or DC – RMS at either the common or multifunction input ports as measured from earth ground.
• Select AC or DC Voltage.
WARNING
• NCV LED will flash and audible alert over 600V AC/DC
• NCV LED will flash without audible alert over 30V AC/DC
Features:
AC Volts (45Hz to 400Hz)
Range Resolution Accuracy Overload Protection
600mV 0.1mV 6V 1mV 60V 10mV 600V 100mV 750V 1.0V
True RMS: 45Hz to 400Hz
RANGE
HOLD
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MIN
PEAK
DL489
z
/
D
u
t
y
True RMS
MFD
Zero
INRUSH
• Default =
• Press x1 =
• Press and hold =
• Press and hold x1 =
T1
30V
T2
TEMP
CATII 1000V
CATIII
600V
MAX
MAX/ MIN
PEAK
± (1.0% +3 dgts) 1000V RMS
DC Volts
Range Resolution Accuracy Overload Protection
600mV 0.1mV 6V 1mV 60V 10mV
± (0.5% +4 dgts)
1000V RMS 600V 1000mV 1000V 1V ±(0.8% +5 dgts)
13
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Frequency (Hz) / Duty Cycle
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True RMS
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
Use CAT III rated leads or higher.
Press the AC/DC volts button to select AC voltage, press and hold the button for Frequency and Duty Cycle modes.
WARNING
Do not attempt to measure more than 750V AC/1000V DC.
Features:
RANGE
HOLD
MAX/ MIN
PEAK
Frequency
Range Resolution Accuracy Overload Protection
99.99Hz 0.01Hz
999.9Hz 0.1Hz
9.999kHz 1Hz
± (0.1% +3 dgts) 600V RMS
99.99kHz 10Hz
Duty Cycle
Range Resolution Accuracy Overload Protection
1.0 to 99.0% 0.1%
±(0.2% per kHz +
0.1% + 5dgts)
Frequency Sensitivity: 1.8Vrms
• Default =
• Press x1 =
• Press and hold =
• Press and hold x1 =
600V RMS
Battery Replacement
When the batteries are too low for safe operation, the Low Battery indicator will display
• Remove the scews from the battery cover. Remove battery cover.
• Replace the old batteries with 6 new (AAA) batteries.
• Replace the battery cover.
• Replace the screws.
S/N
14
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
LRA Inrush
CAT III
600V 600A
T
e
A
m
p
RANGE
NCV
/
A
°
μ
F
°
C
V
MAX/
H
DC
MFD
z
/
D
MIN
Zero
u
t
y
INRUSH
PEAK
DL489
True RMS
• Default = DC Zero
T1
30V
T2
TEMP
CATII 1000V
CATIII 600V
MAX
• Press and hold = LRA Inrush
The UEi LRA Inrush is programmed to properly capture the starting current for compressor motors.
• Select AC Amps.
• Select the range capable of capturing the maximum value.
• Press and hold the DC Zero/ LRA Inrush button – INRUSH will now be shown on the screen.
• Activate the compressor and read value on the display.
• Press and hold the DC Zero/ LRA Inrush button to return to live readings.
Test Lead Notes
Cat IV and CAT III Measurement Locations
4mm
• Ensure the test lead shield is pressed firmly in place. Failure to use the CAT IV shield increases arc-flash risk.
CAT II Measurement Locations
18mm
• CAT IV shields may be removed for CAT II locations. This will allow testing on recessed conductors such as standard wall outlets. Take care not to lose the shields.
WARNING: Test Lead category protections apply only to test leads and should not be confused with the meter’s specific CAT rating. Observe the maximum category protection indicated on the meter the test leads are plugged into.
CAUTION: If the test leads need to be replaced, you must use a new one which should meet EN 61010-031 standard, rated CATIII 1000V or better.
15
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
WARRANTY
The DL489 is warranted to be free from defects in materials and workmanship for a period of 2 years from the date of purchase. If within the warranty period your instrument should become inoperative from such defects, the unit will be repaired or replaced at UEi’s option. This warranty covers normal use and does not cover damage which occurs in shipment or failure which results from alteration, tampering, accident, misuse, abuse, neglect or improper maintenance. Batteries and consequential damage resulting from failed batteries are not covered by warranty.
Any implied warranties, including but not limited to implied warranties of merchantability and fitness for a particular purpose, are limited to the express warranty. UEi shall not be liable for loss of use of the instrument or other incidental or consequential damages, expenses, or economic loss, or for any claim or claims for such damage, expenses or economic loss.
A purchase receipt or other proof of original purchase date will be required before warranty repairs will be rendered. Instruments out of warranty will be repaired (when repairable) for a service charge.
This warranty gives you specific legal rights. You may also have other rights, which vary from state to state.
DISPOSAL
CAUTION: This symbol indicates that equipment and its accessories
shall be subject to separate collection and correct disposal.
CLEANING
Periodically clean your meter’s case using a damp cloth. DO NOT use abrasive, flammable liquids, cleaning solvents, or strong detergents as they may damage the finish, impair safety, or affect the reliability of the structural components.
STORAGE
Remove the batteries when instrument is not in use for a prolonged period of time. Do not expose to high temperatures or humidity. After a period of storage in extreme conditions exceeding the limits mentioned in the General Specifications section, allow the instrument to return to normal operating conditions before using it.
Copyright © 2017 Kane USA Inc. All Rights Reserved. 17398 0417
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...