C165+ QuiCk Start Guide
BACKED BY
CO/CO2
O2/Eff
Aux
Status
Temp
Exch Test
ROOM CO
v3
S
R
P
LINK
C
o
C165+
m
b
u
s
t
i
A
o
n
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
Test Equipment Depot - 800.517.8431 -
TestEquipmentDepot.com
5 Commonwealth Ave, MA 01801
C
o
m
b
u
s
t
i
o
n
A
n
a
l
y
z
e
r
C165+
C
O
C
O
2
T
E
M
P
P
R
S
Status
LINK
v3
Aux
O2/Eff
CO/CO2
Temp
Exch Test
ROOM CO
C165+ OVERVIEW
Sensors
Fitted:
CO
NO
CO-H
2
CO
2
O
2
Serial No.
UEi TEST INSTRUMENTS
A.
B.
C.
N.
O.
D.
E.
F.
G.
Q.
H.
I.
J.
P.
K.
L.
M.
[Top View]
S.
R.
T2
P2
T1
P1
T.
[Bottom View]
U.
A. On/ Off (Power) Button
B. 6 Line Backlit Display
• Press any button to turn Back light on (backlight duration can be set in Menu/
Screen/Backlight)
C. UP/DOWN Button
• Short press to navigate “UP” or “DOWN”
D. Pump Toggle button: Long press to pump on/off, short press holds the readings
and the screen flashes
E. ENTER Button
• Short press select current option displayed
F. Rotary Dial
G. Protective Rubber Boot With Magnets
H. Printing and log button: Long press to saving logs and Short press to print on/off
I. Water Trap (under Protective Boot)
J. Particle Filter (inside water trap)
K. LED Water Trap Indication: LED is active while the pump is on to bring user
awareness to any condensate building up in the water trap
L. Grip Indentation: Indentation for fingers to grip analyzer
M. Water Trap Drain Plug: (Red plug; take caution NOT to damage plug when
removing protective boot)
N. Serial Number QR Code
O. Sensors Fitted: (label under Protective Boot) Indication of sensors installed when
shipped (CO, CO-H2, CO2, NO, O2)
P. Battery Compartment (under Protective Boot)
Q.
Infrared Printer Port
R. Battery Charge USB Adapter Connection
S. Temperature Connections
• Flue Probe Temperature: T1
• Inlet Temperature: T2
T.Flue Gas Inlet Connection
U. Pressure Connections
• Pressure: P1
• Differential Pressure: P2
MENU SCREEN - C165+ START UP
C
o
m
b
u
s
t
i
o
n
A
n
a
l
y
z
e
r
C165+
C
O
C
O
2
T
E
M
P
P
R
S
Status
LINK
v3
Aux
O2/Eff
CO/CO2
Temp
Exch Test
ROOM CO
Press ”Power” Button for 2 seconds. The analyzer
will perform a 10 second purge. This should be done in
fresh air.
Rotate Selector Dial to MENU to set up or customize
your settings.
Selected parameter are highlighted with Display Line
Lights on either side.
Use and ARROW BUTTONS to scroll menu
options.
Press Button to edit a parameter.
Press and ARROW BUTTONS to change
contents of field.
Press Button to enter content and move to next
field.
STATUS SCREEN
Rotate Selector Dial to STATUS to view parameters
Ta
ATM
CAL
DATE
TIME
BATTER
Y LEVEL
Change Fuel Type
With the first line selected press and ARROW
BUTTONS to change currently selected Fuel. (NAT
GAS, H OIL, PELLETS, mmHG, PSI, kPA, PA, mmH2O,
mBar)
Press Button to select.
LINK
CO/CO2
C
o
m
C165+
b
u
s
t
i
Temp
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
o
n
O2/Eff
Aux
Status
BEFORE TESTING
CHECKLIST
o Clean particle filter
o Water trap and probe line are
free of condensate
o All hose and thermocouple
connections are properly
secured
o Water trap is fitted correctly
o Power on and zero
o Flue gas probe is sampling
ambient FRESH air
AUXILIARY SCREEN
Remove the rubber boot and red
drain plug. Allow the water to
drain out. Re-insert the rubber
plug and replace boot cover.
Remove protective rubber boot.
Remove water trap from analyzer.
Remove particle filter from water
trap and replace with new one.
Reattach trap and boot.
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
C165+
m
b
u
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
s
n
t
i
A
o
n
The AUX screen allows you
to assign any of the following
parameters on any display line.
CO2, CO, NO (if fitted), NOx
(if fitted), O2, TF, Ti, Ta, Delta
T, Loss, EFg, Xair, Ra (CO/CO2
Ratio), PI, Fuel Type, PRS or
Blank.
To customize the settings
displayed on screen.
Rotate dial to
.
Scroll or to SCREEN.
Press .
Scroll or to AUX.
Press .
Scroll or to select
the line to change.
Press
.
Highlighted line shows
current selection.
Scroll or to change
parameters.
Press to select.
Scroll or to select
another line to customize
and repeat.
When finished, scroll or
to BACK.
Press .
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
C165+
b
u
s
t
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
i
A
o
n
When performing a
combustion Test.
Rotate function rotary dial to
AUX to Test while viewing
custom parameters that you
selected.
BASIC CO/COMBUSTION ANALYSIS
T2
P2
T1
P1
Insert Flue probe into stack.
Adjust cone so end of the
probe is approximately at the
center of the stack.
NOTE: You will have to drill a
hole at least 3/8”. Use appropriate
sealing method after testing.
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
b
C165+
u
s
t
i
o
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
n
Rotate selector dial to O2/Eff
to view:
CO2
O2
Efgc
T1
Ta
(Status Bar - NAT GAS)
Fuel type can be changed via
or STATUS setting
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
b
C165+
u
s
t
i
o
n
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
Rotate selector dial to CO/
CO2 to view:
CO
COa
LOSS
XAIR O2++
P
(Status Bar - NAT GAS)
Fuel type can be changed via
or STATUS setting.
Make any adjustments as
needed for proper
combustion and wait for
analyzer to display change
in readings. (Repeat as
necessary).
T2
P2
T1
P1
Once complete, remove probe from stack, allow analyzer to purge in fresh air until CO sensor
readings return to ZERO (0) and O2 readings reading return to 20.9%.
Continue to the next test or power analyzer off by pressing , if finished.
NOTE: Print and store functions may be used at any time during testing.
PRESSURE TEST
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
C165+
b
u
s
t
i
o
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
n
Rotate the selector dial to
PRS/TEMP.
Press to Zero Pressure
sensor. No connections
when zeroing pressure.
TEMPERATURE TEST
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
b
C165+
u
s
t
i
o
n
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
T2
P2
T1
P1
Connect true draft hose to P1.
Connect second probe to P2
for differential pressure.
T2
P2
T1
P1
Place combustion probe or
true draft probe tip in the
flue to measure draft.
Connect static pressure
hose to measure differential
pressure.
T2
P2
T1
P1
Rotate the selector dial to
PRS/TEMP
Connect probe to T1.
Compatible with any K-Type
thermocouple probe or clamp.
Connect second probe to T2.
Compatible with any K-Type
thermocouple probe or clamp.
HEAT EXCHANGER TEST
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
b
C165+
u
s
t
i
o
n
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
Rotate dial to EXCH TEST.
Press to start.
The analyzer will wait 60
seconds and then record the
Post-Blower values for CO,
0
2 and Excess Air.
Scroll
or to select
FUELTYPE.
Press
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
b
C165+
u
s
t
i
o
n
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
Test results and LOG number
will display when done.
Press
to print the results.
This LOG will be stored in
REPORTS/EXCHANGE in the
MENU screen.
Call for heat on the system.
Observe and wait for O
2
readings to stabilize.
After the blower turns on,
press the
to start the
Post-Blower test
ROOM CO TEST
O2/Eff
CO/CO2
Temp
O2/Eff
CO/CO2
Temp
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
C165+
b
u
s
t
i
o
C
O
C
r
e
z
y
l
a
n
A
n
Exch Test
T
2
O
ROOM CO
S
R
P
P
M
E
v3
No probes or hose
connections required for
this test.
Rotate dial to ROOM CO.
Press
to select
GENERAL test type.
PRINTING AND LOGGING
Align Printer in line above
analyzer.
CO reading will be logged
every minute for 30 minutes.
Readings will be stored
once the 30 minute test is
completed.
Rotate rotary dial to Menu.
Press
or Buttons to
select Report.
Press Button to select
Report.
Test results and LOG number
will display when done.
Press
to print the results.
This LOG will be stored in
REPORTS/ROOM CO in the
MENU screen.
Press
or Buttons to
view types of Reports.
Press Button to select
Report type.
Press
Button to View.
Press
or Buttons
to select Log number of that
type of Report.
Scroll or to PRINT.
Press Button to print
Report Log Number.
SETUP USER FUEL
CO/CO2
Temp
O2/Eff
Aux
Status
LINK
C
o
m
b
C165+
u
s
t
i
o
n
Exch Test
ROOM CO
v3
S
R
P
P
M
E
T
2
O
C
O
C
r
e
z
y
l
a
n
A
Rotate dial to Menu UNITS shows press to
proceed.
POST TESTING
POWERING OFF
When you power off the C165+, there is a 10 second purge.
CAUTION
Make sure you do not exceed the analyzer’s operating specifications.
•
Do not exceed the flue probes maximum temperature (1112˚F)
•
Remove the probe from the flue
and allow analyzer to purge with
fresh air until readings return to
zero. O
2 to 20.9%
CAUTION: probe tip will be HOT.
Do not exceed the analyzer’s internal temperature range 112°F (50°C)
Do not put the analyzer on a hot surface
•
• Do not exceed the water trap’s level
• Do not let the particle filter become dirty and blocked
BATTERIES
The analyzer is fitted with 3 (AA)
size rechargeable batteries.
Observe correct polarity when
replacing.
Always check operation
immediately after battery
replacement.
Do not leave batteries in unit for
extended periods of non-use.
WARNING
Do not recharge with Alkaline
batteries fitted. Alkaline batteries
are not rechargeable. Attempting
to recharge alkaline batteries
may result in product damage
and create a fire risk.
Time and Date will need to be
reset after changing batteries.
Always dispose batteries using
approved disposal methods that
protect the environment.
WARRANTY
The C165+ combustion analyzer is warranted for one year. Warranty is a manufacturing defect identified within the product’s warranty period. Warranty does not cover batteries, fuses, test leads, probes,
consumables physical damage and misuse. For full warranty details please refer to the Owner’s Manual
on the C165+ product page (see the link above). If a UEi product fails under warranty, we will replace it
but we need the unit back so we can identify and fix the problem.
This warranty gives you specifi
c legal rights. You may also have other rights which vary from state to state.
ANNUAL RECERTIFICATION SERVICES
Complete care for your C160 series combustion analyzer.
When you:
BACKED BY
Request Recertification or Service Online
Within 1 Year of Purchase or Service
UEi will:
6-Year Warranty: All UEi combustion analyzers have a standard
1-year warranty. Each recertification includes a 30-point inspection
and extends the warranty for 1 more year for up to 6 years from the
date of warranty.
24-hour Service: Analyzers received for standard recertification
and service through UEi Service+ are shipped back on the next
business day
Free Shipping: UEi Service+ offers free shipping both to and from
our service center. When customers book their recertification, they
receive a prepaid UPS Ground shipping label.
Register Online
Registering you analyzer online is quick and easy. Just log in or setup an account, it only takes
a couple of minutes. Once logged in you can register you analyzer by providing some product
information and uploading a proof-of-purchase.
When it’s time to request recertifcation, just log into your account, select the analyzer, select
the service and place your order.
Copyright © 2021 Kane USA Inc. All Rights Reserved. 22136 0921
.
Loading...