UDI R/C U29 Plus WIING+ User Manual

U29Plus

User Manual

Catalog

Installing & Removing Component 8

Instruction for Drone and Controller 3

Pre-Flight Checklist 11

Flying Procedure 11

To know your APP 16

Function 14

Using the Flyingsee APP 17

Spare Parts 23

Troubleshooting 26

www.udirc.com

2

Drone

A Propeller

Left Right

Front

Rear

B Propeller

Propeller

Guard

B Propeller

A Propeller

Camera

Switch

Lampshade

Battery

Battery Buckle

Lampshade

Lampshade

Drone Bottom
Housing

Optical Flow Sensor

Lampshade

Drone Cover
Housing

Specifications

Drone Size (Unfolded)

Drone Size （Folded）

Drone Weight

Propeller Diameter

347x366x65mm

204x155x65mm

248g

147mm

Max Streaming Video Range/Radius 20m

100m

150mins

Camera Resolution 1280x720P

Max Flying Time 14mins Frequency

Drone Battery 7.4V 1000mAh Main Motor 1023x4

2.4Ghz

Max Charging Time for Drone Battery

Max Flying Distance/Radius

Instruction for Drone and Controller

www.udirc.com

3

Exploded View

1

2

3

4

5

6

7

8

9

10

11

2

3

5

12

7

8

14

20

18

19

16

15

17

21 22

22

21

24

22 21

23

25

4

29

31

30 27

26

35

36

38

37

1

9

8

20

7

40

5

2

39

9

8

32

7

5

3

2

10

32

33

19

3

33

30

34

9

13

28

28

www.udirc.com

4

21

No.

Name

No.

Name

1

22

2

23

3

24

4

25

5

26

6

27

7

28

8

29

9

30

10

31

11

32

12

33

13

34

14

35

15

36

16

37

17

38

18

39

19

40

Bracket Buckle

Bracket Buckle Spring

Drone Body

Optical Flow Board

Camera Board

Camera Component

Camera Cover

Camera Cushion

Front Bracket Moving Buckle

Camera Lens

Counter-clockwise Motor (Black/White Wire)

Left Rear Bracket Upper Cover

Left Bracket Lower Cover
Left Rear LED Board（Red）

Drone Bottom Housing

Battery Buckle Component

Battery Bracket Spring

Battery Bracket

Left Front Bracket Upper Cover

Left Front LED Board (Green)

20

A Propeller (Clockwise)

Propeller Guard

Transmission Gear

Right Rear Bracket Lower Cover

Motor Holder

Right Rear LED Board (Red)

Transmission Shaft

Lampshade

Cushion

B Propeller (Counter-clockwise)

Right Front Bracket Upper Cover

Right Front LED Board (Green)

Battery

Right Rear Bracket Upper Cover

Drone Cover Housing

Receiver Board

Power Switch

Power Switch Board

Rear Bracket Moving Buckle

Clockwise Motor (Red/Blue Wire)

www.udirc.com

5

Controller

Phone Holder

Power Switch

Left Stick

One Button Take Off /
Landing/ Emergency Stop
Button

Heading Hold Mode

Right Stick

No Function No Function

Picture 3 Picture 4

2. Pull out the arm bracket as per the below arrow shown (Picture 3) , it will
make a click sound, then it means fully unfolded (Picture 4). On the contrary,
then it’s folded.

Note: Improperly operation may cause damage to the bracket part.

Picture 1 Picture 2

Unfolding Instruction

1. Pull out the arm bracket as per the below arrow shown (Picture 1) , it will
make a click sound, then it means fully unfolded(Picture 2). On the contrary,
then it’s folded.

www.udirc.com

6

Controller Button Functions

High / Medium/Low Speed button:

Left Stick:

Right Stick:

Trimmer Mode Button:

Power Switch:

Press to switch to High /Medium/ Low Speed.

Move the Stick to forward / backward / left / right to fly the drone up / down / turn left / turn right.

Move the Stick to forward / backward / left / right to fly the drone forward / backward / left / right.

Press this button and move the right stick to the required trimmer direction, then it
will adjust the direction accordingly. Release the stick to end trimmer mode.

Push up the power switch to turn on the controller, and pull down to turn off.

Heading Hold Mode: Press to enter Heading Hold Mode. Press again to exit Heading Hold Mode.

Take Off / Landing / Emergency Stop Button: Press once and the drone will take off automatically.

Press again and the drone will land automatically. Press and hold the button for more than 1 second for
an emergency landing. The drone propellers will stop and it will land immediately.

Trimmer Mode Button

Battery Cover

High/Medium/Low

Speed Mode

Battery Installation

Open the battery cover on the back side of the controller, insert 4 AA batteries,
following the polarity indicators. ( Picture 5/6, battery is not included)

Picture 6Picture 5

1.Make sure the electrodes are correct. 2.Do not mix new with old batteries.

3.Do not mix different kinds of batteries. 4.Do not charge the non rechargeable battery.

Notice:

Battery Cover

4 x 1.5V

Alkaline Battery

www.udirc.com

7

Drone Battery Li-Po Battery Disposal & Recycling

Wasted Lithium-Polymer batteries must not be placed with household

trash. Please contact local environmental or waste agency or the

supplier of your model or your nearest Li-Po battery recycling center.

Charging Instruction for Drone Battery

Installing & Removing Component

* For faster charging, it is recommended to use an adapter with 5V 2A output current (not included)
to charge the battery

Power BankPhone Charger Computer Charging Car Charger

Drone Battery

1. Connect the drone battery with USB cable first and then choose one of the
method as below picture shown to connect with USB plug.

2. The red USB indicator light keeps bright when charging and the light turns green
when fully charged.

Phone Installation Instruction

1. Pull out the holder until the phone can be hold( Picture 7), then unfold the
lower clamp( Picture 8).

2. Put the phone into the holder, then release the clamp, and the phone will be
fixed on the holder( Picture 9/10).

Picture 7 Picture 8 Picture 9 Picture 10

Notice: Make sure that the button on phone is not clamped.

www.udirc.com

8

Propeller Installation Diagram

Note: Be sure that the A propeller is
on the right arm marked with A letter,
and the B propeller is on the right
arm marked with B letter.

Picture 11

Picture 12

Picture 13

WARNING: The motor’s rotating direction should be the same, or it will not work.
Note: The motor is consumable. If it is damaged, visit the local seller to buy

new motor for replacement.

Motors Replacement

Picture 15Picture 14 Picture 16

1. To remove the propeller, remove the screw from propeller first (Picture 11),
and then pull the propeller out.( Picture 12)

2. To install the propeller , make sure the propeller rotated direction is correct
first, and then mount propeller on transmission shaft of the motor and press
down ( Picture 12), and then fix the screw. ( Picture 11)

1. To remove the motor, remove the screw from the lampshade first(Picture 14)，
then take the lampshade out ( Picture 15) , unplug the motor connector from
LED board and then take the motor out.

2. To install the motor, plug the required motor connector into the LED board
socket,and put the motor into motor holder (Picture 16) . Put on the motor
cover ( Picture 15) and fix it with screw ( Picture 14).

www.udirc.com

9

Picture 21

Prop Guard Assembly Instruction

Installing & Removing Battery

Picture 19 Picture 20

Picture 17 Picture 18

To remove the battery, slide the switch back (Picture 19), and then take the
battery out from compartment.

To install the battery, insert the battery contact chip to drone battery slot first,
and then press the another end down until it makes sound of “ Click”.( Picture 21)

To remove the propeller guard, take out the propeller buckles on both side and
remove the propeller. ( Picture 17)
To install the propeller guard, attach one buckle to the arm and then push another
buckle in until they locks.( Picture 18)

www.udirc.com

10

Pre-Flight Checklist

1. Ensure that the drone battery and controller batteries are fully charged.

2. Ensure that the left stick of the controller is in the middle position.

3. Strictly follow the instructions for the order for turning on and turning off the
controller and drone. Turn on the controller power first and then turn on the
drone power before flying; Turn off the drone power first and then turn off the
controller power when fishing flying. Improper on/off sequence may cause the
drone to fly out of control and could threaten your safety or the safety of others.

4. Ensure the connection between the battery and motor is solid. Vibration during
use may cause a bad connection and the drone could become difficult to control.

5. Improper operation may cause the drone to crash, which may cause motor
defects that could affect flying ability . If this occurs, visit the local distributor
to buy new replacement parts.

Flying Procedure

Frequency Pairing

Turn on the power of controller. The power
indicator will flash rapidly.

Push the left stick all the way down to the
lowest position and then release. The power
indicator will flash slowly and the controller
is ready for pairing .

Press the switch for 2 seconds to power on the drone. The drone body lights
change from flashing to solid , indicating successful frequency pairing.
( Warning Tone)

PUT THE DRONE ON A FLAT SURFACE!

www.udirc.com

11

Calibrating The Drone (After Pairing)

Push the right stick as picture shown.
(Do not move the left stick before
successful calibration) , the drone body
light will flash 3 times , indicating that
drone is calibrating. After successful
calibration, the drone lights will be solid.

Tips: Crashing the drone may cause it to become imbalanced beyond the level
that can be adjusted by the trimmer button. If this occurs, you can
re-pairing & re-calibrate.

Repeat above step several times to practice.

Push the left stick up slowly, the drone
take off .

Move the left stick and right stick at the same
time 45 degrees inward.
(This operation is used for start/lock the
motor. When the motor is working, it could
be used to stop the motor urgently)

Take Off

Landing

Pull down the left stick to its lowest position
slowly to land the drone on the ground.

www.udirc.com

12

Flying Control

www.udirc.com

Left Stick

Move the stick to the left,

then the drone turns to left.

Move the stick to the right,

then the drone turns to right.

Push up the stick, then

the drone flies up.

Pull down the stick, then

the drone goes down.

Right Stick

Move the stick to the right,

then the drone tilts to right.

Move the stick to the left,

then the drone tilts to left.

Pull down the stick, then

the drone goes backward.

Push up the stick, then

the drone flies forward.

Left/Right Rotates Trimmer

When you take off, if the drone head rotates to the left, press the
trimmer button, and push left stick to right. Otherwise push to the left.

Forward/Backward Trimmer

When you take off, if the drone tilts forward , press the trimmer button,
and push the right stick backward. Otherwise push forward.

Left/Right Tilts Trimmer

When you take off, if the drone tilts to the left, press the trimmer
button, and push the right stick to the right. Otherwise push to the left.

Trimmer

mode

13

www.udirc.com

Altitude Hold Mode

To use Altitude Hold Mode, push the left stick up to fly the
drone up, or pull the stick down to fly down, to your
desired altitude , and then release the stick . The stick
will move back to the center position( Picture 22). The
drone will continue flying at its current altitude . Repeat to
change the drone altitude. (This function is available by default)

Note: If the propeller is deformed or damaged, the Altitude Hold Mode will fail.
If the atmospheric pressure is instability, the Altitude Hold Mode will fail.

Altitude Hold Mode allows the drone to maintain a consistent altitude while
allowing roll, pitch, and yaw to be controlled normally. This mode makes it easier
for beginners to control the drone and makes the drone
more stable for aerial photography.

One Button Take Off And Landing

Function

One Button Take Off

After calibration successfully, press this button, the drone
will fly up and keep flying at an altitude of approximately

1.2 meters.

Emergency Landing

Press to land the drone automatically. (In this mode,
DO NOT touch the left stick, or the function will fail)

One Button Landing

If the drone is in an emergency situation , such as if
it is about to hit people or obstacles, press the
Take Off / Landing / Emergency Stop Button and hold it for more than
1 second. The propellers will stop immediately and the drone will land quickly.

Picture 22

Altitude Hold Center

Position Hold Mode allows the drone to maintain a consistent position while
allowing roll, pitch , and yaw to be controlled normally. The Positioning Mode and
Altitude Hold Mode makes the drone more stable for aerial photography.

Notice: The ideal altitude of position hold is within 8m. The Position Hold can not work
well when flying too high or flying in the dark light or evening.

Positioning Hold Mode

14