HBC 100
User Manual
Helmet Communicator
1
Welcome to
HBC100
Helmet Communicator User Manual
HBC100 helmet communicator
control unit
Hi-fi stereo headset
User manual
A clip bracket and
anti slip rubber patch
An AC charger and
USB charging cable
velcros for speakers
Metal mounting bracket and
2
Contents
Contents --------------------------------------------- 2
Quick User Guide ------------------------------------ 3
Warnings and Safety Instructions ------------------ 7
Features --------------------------------------------- 9
Installation ------------------------------------------ 10
General Operations --------------------------------- 14
Mobile Phone Operations --------------------------- 16
Music Streaming Operations ----------------------- 18
Inter
com Operations ------------------------------- 19
Button Configurations Summary ------------------ 20
Status Indicator Configurations Summary -------- 21
Technical Data -------------------------------------- 22
Troubleshooting Operational Tips ------------------ 23
Notices ---------------------------------------------- 24
Quick User Guide
Your HBC100 at a glance
Up button
Speaker /
charging socket
Down button
Status
indicator
Answer
button
Charge
Check Bluetooth phone capabilities before use
To charge, use the provided charging cable by connecting
it either to a USB port or to the adaptor provided.
While charging, the status indicator light will be red.
Upon fully charged, the status indicator light will be blue.
Low Battery Indicator
You need to charge the helmet communicator when the
status indicator light blinks red twice every 2 seconds
with a beep every minute.
Charger
Attach
G
ENERAL FUNCTIONS
Before using your HBC100
please charge it first!
3
Make sure the speaker wire
is inserted into the main unit.
lnsert the speaker wire into the control unit until you
can no longer see the 3 ribs on the speaker wire plug.
Install Speakers
4
Power On
Hold Answer for 2 seconds.
Power Off
Hold Answer for 5 seconds.
Reset
Press all 3 buttons
together.
Volume Up
Press Up once.
*NOTE: The volumes for mobile phone, music and intercom
functions are controlled separately.
M
OBILE PHONE FUNCTIONS
Pairing your HBC100 with your mobile phone
Volume Down
Press Down once.
Pairing
Check Bluetooth phone capabilities before use.
Hold
Up
and
Down
buttons together for 2 seconds. The
status indicator light will blink blue then red.
From your mobile phone Bluetooth menu, search for
‘UCLEAR HBC100’.
If your phone requires a password, enter ‘0000’.
Quick User Guide
Quick User Guide
Answer Incoming Call
Use voice pickup, say ‘hello’
or ‘pickup’.
OR
Manually press
Answer
button once.
Voice Dial
Hold
Answer and Down
button for 2 second.
Last Number Redial
Hold Answer and
Up
button for 2 second.
3 Way Calling
To swap between 2
concurrent calls, press
the Answer button once.
M
USIC STREAMING FUNCTIONS
*NOTE: For music Bluetooth adaptor you would need to pair
Reject/ End Incoming Call
Hold Answer button for 2 seconds.
the music Bluetooth adaptor before using it with HBC100.
Play/ Stop (Quick Mute)
Press the
Answer button
2 times.
Pairing (for Music
Bluetooth adaptor Only)
Hold
Up and Down buttons
together for 2 seconds.
5
Quick User Guide
6
Fast Forward
Press the Up button 2
times.
Backtrack
Press the Down button
2 times.
I
NTERCOM
F
UNCTIONS
Pairing your HBC100 to another HBC100
Helmet 1
(Master Unit)
Helmet 2
(Secondary Unit)
Pairing (Needs to be done once)
The helmet communicator needs to be switched off
before performing the following steps:
Press Answer and Down buttons for 5 seconds on
helmet 1 & press Answer and Up buttons for 5
seconds on helmet 2.
Initiate or Terminate Conversation
(Toggle Functions)
Hold the Up button for 2 seconds.
Warnings and Safety Instructions
This manual uses the and icons to highlight
certain instructions. Below is an explanation of the icons.
Attention
- This icon highlights special instructions and precautions intended
to avoid damage to the system. Non-compliance may void the
product warranty.
Warning
- This icon provides precautions important to prevent injuries to
the user.
Attention
- Please read through the operating instructions to understand
how to operate the system, in particular the safety instructions.
Warning
!
- Please note that there are some countries that by law disallow
the rider to set the helmet communicator to a volume
that prevents you from perceiving the surrounding.
- Please note that in some countries the use of both speakers
simultaneously is authorized only out of pubic traffic
conditions.
- Please check with the relevant authorities for local safety
legislation before using the helmet communicator on
the road.
7
8
- Prolonged exposure to loud sounds may lead to permanent
hearing damage.
- Do not attempt to place an outgoing call through the mobile
phone while riding on the motorcycle at any point of time.
-
Please do not use the helmet communicator in any
way that may distract you or hinder your judgment while on
the move.
Never ever compromise your safety and the safety
of others.
Attention
- Charging and handling rechargeable battery products incorrectly
may cause them to overheat, catch fire or explode. To prevent
this please follow the instructions below:
i) Never change the batteries yourself, always bring it to an
authorised dealer to perform the replacement for you.
ii)When charging, use the charging cable provided or
areplacement cable from the dealer. Using similar,
compatible or any other cables may lead to permanent
product damage and will void the product warranty.
ONLY
- Never make any modifications to any parts of the
helmet communicator in any way as it may cause the system
to malfunction causing hurt to you.
- Do not modify your helmet to use with this system – it is not
necessary to do so.
!
Warnings and Safety Instructions
Features
•
•
Voice controlled incoming call answering.
•
The helmet communicator has three main functions:
to make mobile phone calls, to listen to music and intercom
communication.
Mobile Phone Functions
Bluetooth phone audio capabilities, HFP & HSP Profile.
• Voice activated call pick up.
Music Streaming Functions
• Bluetooth music streaming with hi-fi and stereo capabilities,
A2DP Profile.
• Bluetooth Audio/Video Remote Control capability, AVRCP
profile.
Intercom Functions
Motorcycle to motorcycle or rider to passenger connection via
two helmet communicator up to 10m range.
Advanced Product Features
•
Self adaptive intelligent noise cancellation algorithms ensure
conversations on the go are clear even in noisy environments.
•
The weather resistant engineered design ensures the possibility
of communication rain or shine.
•
The integrated microphone array technology allows you to
communicate without the hassle of using boom microphones.
9
10
Installation
The HBC100 helmet communicator package
contains :
A HBC100 helmet
communicator control unit
A pair of hi-fi stereo headset with embedded
microphones
Velcros for speakers
A clip bracket and
anti slip rubber patch
A metal mounting bracket with double sided tape
An AC charger and
USB charging cable
A user manual
•
11
• Use the velcros to install the
speakers into the ear cavity of the
helmet.
Install Speakers
• The microphones be placed
facing out.
MUST
Left and right speakers must be
installed symmetrically.
•
Make sure the speaker wire is inserted into the main unit.
lnsert the speaker wire into the control unit until you
can no longer see the 3 ribs on the speaker wire plug.
Installation
Microphone
12
Installation
When in the correct position, the clip bracket should be firmly
secured onto the helmet.
Your HBC100 helmet communicator package
comes with 2 types of mounting bracket: a clip bracket
and a metal mounting bracket. Use either of the
brackets to install the HBC100 control unit onto your
helmet.
Install Clip Bracket
• Position and fasten the clip bracket onto the helmet.
•
• Use additional anti slip rubber patch provided if required.
• Remove the metal handles after clip bracket has been
installed.
13
Installation
Install Metal Mounting Bracket
Identify a position on the helmet to adhere the Metal
Mounting Bracket.
Peel off the double sided tape protective film.
• Slide main unit onto the clip bracket. You should hear a ‘click’
sound when fully inserted.
• Fully insert the speaker USB connector.
•
•
• Carefully place the Metal Mounting Bracket onto the position
identified in step 1. (You may only do this step once)
• Apply slight pressure onto the metal mounting bracket to
ensure that the metal mounting bracket is firmly secured.
Make sure that permanent metal mounting clip is installed with
the 2 side holes at the top and the metal prong pointing down.
•
Install Main Unit
14
Your HBC100 helmet communicator is now setup
and ready to go!
Power On
• Hold the Answer button for 2 seconds to power on the helmet
communicator. The status indicator will blink blue and a
power up tone can be heard.
Power Off
• To switch off the helmet communicator, press and hold the
Answer button for 5 seconds. The status indicator will blink
red 5 times followed by a long beep before fully shutting
down.
• If the intercom feature has been in use, and all other
Bluetooth devices have been disconnected, the system will
auto shutdown in 1 hour. If the intercom feature has not
been in use and the HBC100 has not connected to any other
device, the system will auto shutdown in 10 minutes.
Low battery
• When the battery level is low, the status indicator light will
flash red twice every 2 seconds while emitting a warning
beep every minute.
The operations described here are applicable to all modes
of operations.
Power Save Mode (Auto Power Off)
Up button
Answer
button
Speaker /
charging socket
erations General Op
Status
indicator
Down button
Charging the Unit
Volume Control
• The volume control of the helmet communicator can be
controlled using the Up and Down buttons. Pressing the Up
or Down button will increase the volume respectively.
The
volume control for each mode is independent of each other.
• Automatic pairing of the helmet communicator with music
devices is dependent on the music devices.
Automatic Profile Switch
• The helmet communicator supports multiple profiles
concurrently, but at any point of time only one profile is
active. The automatic profile switch determines which profile
should be active at any point of time starting from the highest
priority: (1) Mobile Phone functions (2) Intercom functions
and (3) Music functions.
The helmet communicator can be paired to more than 1 device.
However to achieve the most out of the helmet communication,
we do not recommend pairing more than 2 devices to the
helmet communicator at one time
General Operations
• To charge the helmet communicator, connect the provided
charging cable to the speaker/ charging socket. Upon
charging, if the unit is on, the system will automatically
initiate power down.
Automatic Speaker Loudness (Communication only)
The speaker loudness will be automatically adjusted
depending on the environment noise level. However you can
still adjust the volume manually.
•
Automatic Pairing
• The helmet communicator has the ability to connect to the
last paired device automatically for two features – music and
mobile phone.
•
15
16
‘UCLEAR HBC100’
To use the helmet communicator with your mobile
phone for the first time, you must first connect them
via Bluetooth pairing.
Pairing
• To connect the helmet communicator to a mobile phone,
hold the Up and Down buttons for 2 seconds. This puts the
helmet communicator into paring mode. The status
indicator will blink blue then red.
• Next, turn on the mobile phone Bluetooth functions and
search for Bluetooth devices. Select to
pair with the desired device.
• When prompted to enter a passcode, enter
‘0000’
.
*Most mobile phones will automatically connect with both
phone and music Bluetooth capabilities when paired with the
helmet communicator.
After pairing the helmet communicator to your mobile
phone, you may now use the helmet communicator to
answer your calls or make outgoing calls or listen to
music.
Voice Activated Pick Up Calls
•
OR
Reject Calls
• To reject an incoming call or an incorrectly placed outgoing
call hold the Answer button for 2 seconds.
tions Mobile Phone Opera
When a call comes to the mobile phone, say ‘hello’ or ‘pickup’ to answer the call press the Answer button once.
17
•
•
•
•
•
•
Voice Call
To activate t he voice call feature, hold the Down and Answer
buttons for 2 seconds. The accuracy of the voice dialing
feature is dependent on your mobile phone s capabilities.
Last Number Redial
Mobile Phone Operations
To redial the last number, hold the Up and Answer buttons
for 2 seconds. The capability of this function is dependent
on the mobile phone used.
3 way calling
While on a call, if an incoming call comes in, you may answer
the call by pressing the Answer button once.
To swap between 2 concurrent calls, press the Answer button
once.
To end a call during a 3 way call, holding the Answer button
for 2 seconds will end the active call. Upon terminating
the active call, the call
on hold will become active.
Music Feature
If the mobile phone supports A2DP/AVRCP profile, user may
activate the music by playing it directly from the phone or by
controlling the phone via the helmet. To operate refer to
Music Streaming Operations section. Should the documented
steps fail to activate A2DP/ACRCP profiles, please refer to the
user manual of your pairing device (e. g. phone, ipod, etc...).
,
To use the helmet communicator with your music devices
you must connect them wirelessly through Bluetooth
pairing. This step is only required for Bluetooth music
streaming devices.
To connect the helmet communicator to a Bluetooth music
device, hold the Up and Down buttons for 2 seconds. This
puts the helmet communicator into pairing mode. The
status indicator will blink blue and red alternately.
Pairing
•
Next, put the Bluetooth music device into pairing mode.
Both the helmet communicator and the music device should
automatically pair together.
•
Music Streaming Operations
•
After pairing the helmet communicator to a music
device, you may use the helmet communicator to
wirelessly listen music stored on the device.
Play & Stop
The Play and Stop command is a toggle function. To play
music, press the Answer button 2 times. Pressing the Answer
button 2 times while music is play will stop it.
Fast Forward
• To skip to the
next track, press the Up button 2 times.
Backtrack
•
the Down button 2 times.
To skip
to previous track, press
18
In order to use the helmet communicator to remotely
control the music, the music device must have
Bluetooth Audio/Video Remote Control capability,
AVRCP profile.
Pairing readies one helmet communicator to search for
the other. This process needs to be carried out only once.
With both helmet communicators powered off, hold for
5 seconds Answer and Down buttons on one helmet and Answer
and Up buttons on the other. The indicators of both helmets
would blink blue and red alternately while connecting.
While pairing, there must not be other intercom units nearby.
It is recommended that after the pairing process is successful,
power down and restart both helmet communicators.
19
To use the intercom profile on the helmet communicator
for the first time, you would need to first connect the two
helmet communicators wirelessly by pairing.
Pairing
•
•
Intercom Operations
• While pairing, there must not be other intercom units nearby.
• It is recommended that after the pairing process is successful.
Restart both helmet communicators.
After pairing the two helmet communicators, you
may now use the intercom profile.
Initiate Intercom (Toggle function)
• To start conversation, hold the Up button for 2 seconds.
Terminate Intercom (Toggle function)
• To end the conversation, hold the Up button for 2 seconds.
•
•
In the event the intercom is interrupted by incoming calls or
the link breaks when out of range, you may try to resume
the connection by voice. Say “hello” loud and clear into the
mouthpiece.
If the intercom session has been manually disconnected
(Terminate Intercom by Toggle Function above), then VOX
feature will not work. You must manually re-initiate the
connection again. See Initiate Intercom (Toggle function).
Using VOX (Voice Activation) to Resume Intercom
•
•
20
The table below shows the button configurations.
Action Button
Common Instruction Commands
Power on Hold
Answer
for 2 seconds
Power off Hold
Answer
for 5 seconds
Activate Bluetooth pairing Hold Up &
Down
for 2 seconds
V Up once olume up Press
Volume down Press
Down
once
sserP teseR
Answer, Up
&
Down
once
Voice Calling
Pick up incoming call Press
Answer
once
End call in progress Hold
Answer
for 2 seconds
Reject incoming call Hold
Answer
for 2 seconds
Voice dial Hold
Answer
&
Down
for 2 seconds
Last number redial Hold
Answer
& Up for 2 seconds
Music Streaming
sserP yalP
Answer
2 times
sserP potS
Answer
2 times
Fast forward track Press Up button 2 times
Backtrack Press
Down
button 2 times
Intercom
Pairing as helmet 1
aster unit)
While unit is off, hold Answer
and
Down
for 5 seconds (m
Pairing as helmet 2
While unit is off, hold Answer
and
Up
for 5 seconds (secondary unit)
Connect intercom Hold Up for 2 seconds
Disconnect intercom Hold Up for 2 seconds
ry Button Configurations Summa
Resume intercom (VOX) Say “Hello” for voice activation
The table below shows the status indicator configurations.
State Status Indicator
1 Off (No power) -
2 On (BT* not connected) Blink blue fast
3 On (BT* connected) Blink blue slowly
4 Phone & Music device Blink blue &
Pairing mode
red alternately
5 Call in progress Blink blue very slowly
6 In-coming call Blink blue & red alternately
7 Battery low Blink red every 2 seconds
8 Power down Blink red 5 times
9 Intercom connected Blink blue twice every 2
seconds
10 Intercom Pairing mode
(master unit)
Blink purple fast
11 Intercom Pairing mode Blink purple slowly
(secondary unit)
12 Battery charging Solid Red
13 Battery fully charged Solid Blue
14 Battery faulty Solid purple
*
BT - Bluetooth
Status Indicator Configurations Summary
21
Technical Data
Unit
Dimensions (L x W x H) 6 0mm x 15mm 0mm x 4
g03 thgieW
Audio
Frequency response 30Hz to 20kHz
Sampling rate 48kHz, 16 bit
SPL 105dB + 2dB
THD 0.5%
Bluetooth
Specifications Version 2.1 EDR, Class 2
Profiles HSP, HFP, A2DP, AVRCP, Intercom
Radio
Carrier frequency 2.402 – 2.480 GHz
Range Up to 10m (op
en field)
RF output power -0.03 dBm
Power
Power consumption 200mW (max)
Power input (charging) 5V / 400mA / 2W
Built-in battery 3.7V, 570mAh, Lithium-ion Polymer
(Rechargeable)
Music/talk time Up to 10 hours
Standby time 400 hours
Temperature
Operation temperature -10°C to +60°C (14°F to +140°F)
Charging temperature 0°C to +45°C (+32°F to +113°F)
Storage temperature -40°C to +80°C (-38°F to +176°F)
22
23
- The sound quality and voice activation feature are dependent
on the capabilities of your mobile device (e.g. mobile phone).
Make sure that your mobile or pairing device is using the
most current software updates.
- For best sound quality try adjusting volume levels of your
master pairing device to 70% or until you achieve best
results.
- Try experimenting with your pairing device, turn the volume
to 50%,75% and 100% to find which combination works best
for your settings.
- The HBC100 will fit on most helmets, 1/2 face, 3/4 face
or modular helmets. As long as your helmet has speaker pockets or
a place for the speakers, as well as a mounting surface for the control
unit, the HBC100 will most likely work with your helmet.
- You can use the HBC100 on most helmets:
Motorcycle
Motocross
Snowmobile
Ski or Snowboard
Troubleshooting Operational Tips
24
Notices
Without prejudice of legal warranty, the product is covered
under a 1 year warranty by manufacturer from the date of
purchase. Please provide the proof of purchase when you
return the item to the supplier.
The warranty covers manufacturing defects only.
The warranty is voided by any unauthorized repairs, misuse,
misapplication, tampering of the product, modifications,
upgrading or results of any failures to follow the guidelines
as set out in the product brochure or by any of the actions
specified in this brochure or anywhere in our technical
publishing released to the public from time to time which
would have voided the warranty.
CHARGING NOTICE:
To reduce the risk of personal injury, electrical shock, fire or
damage to equipments, please follow all the instructions below:
- Do not immerse the product, AC adaptor or speakers in water.
-
Do not install, place or use the product near any source of heat
for example: stove, radiator, oven, toaster, coffee maker or
other apparatus that gives off heat.
- Always use the provided AC power adaptor and cable included
in the package to charge the product. Use of any incorrect power
supply to charge the product may cause permanent damage to
the product and render the warranty void.
WARRANTY: (Applies only to customers outside of the USA and
Canada. For customers in the USA and Canada, please refer to the
warranty card. )
BATTERY WARNING:
The helmet communicator contains a rechargeable
lithium ion polymer battery. To reduce risks of fire or burns, do
not disassemble, crush, puncture, short external contacts or
dispose in fire or water.
25
Notices
LIMITATIONS OF WARRANTY:
All product warranties for the product by are limited to
those mentioned in the product manual.
WAIVER AND DISCLAIMER:
BITwave, FSC and all their representatives, agents, distributors,
suppliers and resellers shall not be liable and will be held harmless
from any and all litigation, claims, debts, demands, actions and
liability which may arise, directly or indirectly, from operating or
using the product for any damages, losses, distress, pain, suffering,
discomfort, loss and injuries including bodily harm illness, strains,
fractures, partial and/or total paralysis, death or other ailments
that could cause serious disability either to any persons, or any
parties whether the user or other third parties or their possessions,
or to any goods, vehicles, properties, assets among others including
your own suffered by any persons, organizations, or any third parties
whether physical or otherwise and which may accrue to you in the
future, to the fullest extent permitted by law as a result of the use,
operation, malfunctioning, misuse, disposal or repairs of the product
or any other reasons, conditions or circumstances or attempts todo
so whether due negligence, omissions or otherwise of BITwave,
FSC or any of their representatives, partners, agents, distributors,
suppliers, resellers, designer, manufacturer or any others in its
supply and distribution chain or any third parties involved.
Warranty does not cover data recovery and physical deterioration
due to use, damages resulting from accidents, storage, loss or
data loss or damage during repairs or transits. The sender will
bear all transportation charges for functioning products but which
were declared defective.
Notices
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
This Class【B】 digital apparatus complies with Canadian
ICES-003.
Cet appareil s’accorde avec Industrie Canada licence-exempte
RSS standard.
(1) cet appareil ne peut pas causer l’intervention, et (2) cet
appareil doitaccepter de l’intervention, y compris l’intervention
qui peut causer l’opération non désirée de.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada
TECHNICAL SUPPORT:
For additional information please visit our website at
www.uclear-digital.com
For customer and technical support in the US and Canada,
please contact:
BITwave USA LLC
1093 E lron Eagle Dr. #115
Eagle, ID 83616
1-855-BIT-WAVE
FCC COMPLIANCE STATEMENT FCC ID:NMC2010HBC100A
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operations.
Note: The manufacturer is not responsible for any radio or tv
interference caused by unauthorized modifications to this
equipment. Any modifications to the equipment will void the
manufacturer’s warranty.
Notices
28
COPYRIGHTS:
Copyright © 2011 BITwave Pte Ltd & FSC. All rights reserved.
No part of this guide may be reproduced in any form or by any
process whatsoever without prior written consent from BITwave
Pte Ltd and FSC.
LICENCES:
The trademark and logo is exclusively owned by BITwave
Pte Ltd & FSC. Any use of the mark by any other parties without
prior written permission of BITwave Pte Ltd & FSC constitutes an
infringement of legal rights. The Bluetooth trademark is owned
by Bluetooth SIG and is used under licence by BITwave Pte Ltd
& FSC.
Notices
PERSONAL SAFETY:
Do not open the seal of the hardware, tamper, repair or modify
any parts. Do not touch the product with metal objects or parts
or chemical products. Violation of the above will lead to
potential fire hazards and mishaps.
Please contact the technical support or your local supplier if
your product malfunctions.
Always comply with the local law and traffic regulations. Where
use of the product is not permitted or allowed by any laws and
regulations including the traffic laws of your country, we warn
you not to go against such restrictions. You will bear the full
responsibilities of any breaches of law and regulations.
You should not allow the operations or use of the product or any
attempts to use it by any persons including yourself to
compromise anyone’s safety including your own or to cause
harm to any vehicles, property, objects, livestock, inventories,
assets and the like under any circumstances. You or any users
of the product are to take all necessary safety measures and
precautions and to remain alert to all surrounding conditions.
You are warned not to operate the product if you are not
physically capable of doing so in a safe manner, if you have or
will consume any alcohol or any mind-altering substance during
its operation so that your alertness is compromised or if you
have any medical conditions or needs that may compromise
your abilities to do so in a safe manner.
We warn you of the inherent, unforeseeable and unlimited risks
and dangers in using the product while in traffic, including injury
or illness, strains, fractures, partial and/or total paralysis, death
or other ailments that could cause serious disability due to any
causes.
This product is only for use by persons eighteen (18) years of
age and above who have understood the warnings, risks and
the terms of use.
You confirm that you have read this release of liability and fully
understand its terms and that you have given up substantial
rights by using or attempting to use the product.
27
26
CORRECT DISPOSAL OF THIS PRODUCT:
Do not dispose this product with other household wastes at the
end of its working life. There is a separate collection system for
used electronic products in accordance with legislation that
requires proper treatment, recovery and recycling.
Household users should contact either the retailer where they
purchased this product, or their local government office, for
details of where and how they can take this item for
environmentally safe recycling. Business users should contact
their suppliers and refer to the terms and conditions of the
purchase contract. This product should not be mixed with other
commercial wastes for disposal.
Notices
PRODUCT INFORMATION:
BITwave, FSC and all their representatives, agents, distributors,
suppliers or resellers shall not be held responsible for any
consequences arising from any errors or omissions in the guide
or resulting directly or indirectly from the use of the information
herein. BITwave and FSC reserve the right to amend or improve
the product design or user guide without any restrictions and
without any obligation to notify users.
All information here is accurate as of the date of printing.
Please check for the latest version of any the modified or
upgraded product on the website www.uclear-digital.com from
time to time.
All risks from operating or usage of the product rest solely and
entirely with the user of this product, the original purchaser or
any third parties, who assumes full responsibility for all injuries,
losses and/ or damages, whether caused in whole or in part by
the negligence, omissions or other conduct of others, including
that of BITwave, FSC and all their representatives, partners,
agents, distributors, suppliers, resellers and all others in its
supply and distribution chain either due to the designer’s or
manufacturer’s negligence or omissions or any third parties
involved.
US-PUB#1B
Loading...