u-blox EVK-NINA-W132, EVK-NINA-W1,EVK-NINA-B2, EVK-NINA-W102, EVK-NINA-W101, EVK-NINA-W131 User Manual
...
EVK-NINA-W1/EVK-NINA-B2
Evaluation Kit for NINA-W1 and NINA-B2 modules
User Guide
Abstract
This document describes how to set up the EVK-NINA-W1/EVK-NINA-B2 evaluation kits to evaluate
NINA-W1 series and NINA-B2 series stand-alone modules. It also describes the different options for
debugging and the development capabilities included in the evaluation board.
www.u-blox.com
UBX-17011007 - R05
EVK-NINA-W1/EVK-NINA-B2 - User Guide
UBX-17011007 - R05 Page 2 of 21
Document Information
Title EVK-NINA-W1/EVK-NINA-B2
Subtitle Evaluation Kit for NINA-W1 and NINA-B2 modules
Document type User Guide
Document number UBX-17011007
Revision and date R05 29-Nov-2018
Disclosure Restriction
This document applies to the following products:
Product name Software version PCN reference
EVK-NINA-W101 N/A EVK-NINA-W102 N/A EVK-NINA-W131 N/A -
EVK-NINA-W132 N/A EVK-NINA-W151 N/A EVK-NINA-W152 N/A EVK-NINA-B221 N/A -
EVK-NINA-B222 N/A -
u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this
document. Copying, reproduction, modification or disclosure to third parties of this document or any part thereof is only
permitted with the express written permission of u
-blox.
The information contained herein is provided “as is” and u
-blox assumes no liability for its use. No warranty, either express or
implied, is given, including but not limited
to, with respect to the accuracy, correctness, reliability and fitness for a particular
purpose of the information. This document may be revised by u
-blox at any time without notice. For the most recent
documents, visit www.u
-blox.com.
Copyright © u
-blox AG.
EVK-NINA-W1/EVK-NINA-B2 - User Guide
UBX-17011007 - R05 Page 3 of 21
Contents
Document Information ................................................................................................................................ 2
Contents .......................................................................................................................................................... 3
1 Product description .............................................................................................................................. 4
1.1 Overview ........................................................................................................................................................ 4
1.2 Kit includes ................................................................................................................................................... 6
1.2.1 EVK-NINA-B221 and EVK-NINA-W1x1 .......................................................................................... 6
1.2.2 EVK-NINA-B222 and EVK-NINA-W1x2 .......................................................................................... 6
1.3 I/O allocation................................................................................................................................................. 6
1.4 Jumper description .................................................................................................................................... 7
1.4.1 Default jumper configuration ........................................................................................................... 9
1.4.2 RMII to PHY jumper configuration................................................................................................... 9
1.5 LEDs .............................................................................................................................................................10
1.5.1 RGB-LED Jumper configuration ....................................................................................................10
1.6 Connectors .................................................................................................................................................11
1.7 Buttons ........................................................................................................................................................11
1.8 Configuration options ..............................................................................................................................12
1.8.1 Power supply ......................................................................................................................................12
2 Setting up the evaluation board ..................................................................................................... 13
2.1 EVK without software (open CPU) .........................................................................................................13
2.2 EVK with u-blox connectivity software .................................................................................................14
2.2.1 Starting up .........................................................................................................................................14
2.2.2 Getting the latest software ............................................................................................................14
Appendix ........................................................................................................................................................ 15
A Layouts.................................................................................................................................................... 15
B Schematic drawings ........................................................................................................................... 16
C Glossary .................................................................................................................................................. 19
Related documents ................................................................................................................................... 20
Revision history .......................................................................................................................................... 20
Contact ........................................................................................................................................................... 21
EVK-NINA-W1/EVK-NINA-B2 - User Guide
UBX-17011007 - R05 Product description Page 4 of 21
1 Product description
1.1 Overview
The EVK-NINA-W1/EVK-NINA-B2 evaluation kit includes an evaluation board, which can be used as a
reference design for the NINA-W1 or NINA-B2 series modules, a quick start guide, and a USB cable.
For the NINA-B221 and the NINA-W1x1 module, the evaluation board is prepared with a U.FL coaxial
connector for connecting the external antenna. The NINA-B222 and the NINA-W1x2 module has an
onboard antenna; thus the EVK-NINA-B222 and the EVK-NINA-W1x2 evaluation board does not have
a U.FL connector.
The main features of the EVK-NINA-W1/EVK-NINA-B2 are:
• Available in several variants:
o NINA-B221 and NINA-B222
o NINA-W101 and NINA-W102
o NINA-W131 and NINA-W132
o NINA-W151 and NINA-W152
• All of the module pins are available at connectors or jumpers
• Can be powered through USB (J8) or external power supply (J23)
• Equipped with a Quad High Speed USB to Multipurpose UART/MPSSE IC (FT4232) that allows
serial communication and flashing over USB.
The EVK-NINA-W1/EVK-NINA-B2 evaluation kits are available in the following variants, depending on
the NINA module that is mounted on the EVK:
• EVK-NINA-B221 – Evaluation kit for NINA-B221 module, RF port available on U.FL connector (J21)
• EVK-NINA-B222 – Evaluation kit for NINA-B222 module with onboard antenna
• EVK-NINA-W101 – Evaluation kit for NINA-W101 module, RF port available on U.FL connector
(J21)
• EVK-NINA-W102 – Evaluation kit for NINA-W102 module with onboard antenna
• EVK-NINA-W131 – Evaluation kit for NINA-W131 module, RF port available on U.FL connector
(J21)
• EVK-NINA-W132 – Evaluation kit for NINA-W132 module with onboard antenna
• EVK-NINA-W151 – Evaluation kit for NINA-W151 module, RF port available on U.FL connector
(J21)
• EVK-NINA-W152 – Evaluation kit for NINA-W152 module with onboard antenna
This section describes the main connectors and settings that are required to get started. Figure 1
and Figure 2 show the two different antenna variants of the EVK-NINA-W1/EVK-NINA-B2 evaluation
board.
EVK-NINA-W1/EVK-NINA-B2 - User Guide
UBX-17011007 - R05 Product description Page 5 of 21
Figure 1: EVK-NINA-W1/EVK-NINA-B2 evaluation board with U.FL connector for external antenna
Figure 2: EVK-NINA-W1/EVK-NINA-B2 evaluation board with internal antenna
⚠ Take care while handling the EVK-NINA-B222 and EVK-NINA-W1x2. Applying force to the NINA
module might damage the internal antenna.
EVK-NINA-W1/EVK-NINA-B2 - User Guide
UBX-17011007 - R05 Product description Page 6 of 21
1.2 Kit includes
1.2.1 EVK-NINA-B221 and EVK-NINA-W1x1
The EVK-NINA-B221 and EVK-NINA-W1x1 evaluation kits include the following:
• EVK-NINA-B221 or EVK-NINA-W1x1 evaluation board
• 2.4 GHz foldable antenna (Ex-It 2400) with reverse polarity SMA connector
• RP-SMA - U.FL cable assembly, 100 mm length
• USB cable
• Quick Start guide
1.2.2 EVK-NINA-B222 and EVK-NINA-W1x2
The EVK-NINA-B222 and EVK-NINA-W1x2 evaluation kits include the following:
• EVK-NINA-B222 and EVK-NINA-W1x2
• USB cable
• Quick Start guide
1.3 I/O allocation
The block diagram in Figure 3 provides a better understanding of how I/O signals from the module are
made available at connectors and/or interfaces of the EVK.
Sixteen (16) I/O signals are available at the middle row of the I/O allocator. These signals can be
distributed to connectors and/or interfaces on the EVK by use of jumpers to connect the associated
middle and outer row pin(s).
The signals IO-12, IO-13, IO-14 and IO-15 can be disconnected from the J4 connector by not
populating the corresponding jumpers at J18. This can be useful if the SDIO signals D2, D3, CLK, and
CMD are directed to the SD card reader (J19).
Eight signals are connected directly between the module and the J2 or J3 connector.
Figure 3: Block diagram of EVK-NINA-W10
EVK-NINA-W1/EVK-NINA-B2 - User Guide
UBX-17011007 - R05 Product description Page 7 of 21
☞ When reset-n is released, the module pin 27 is read as boot-n. When IO-0 is connected to the
module, it must be held high during start up.
1.4 Jumper description
Parameter Description Name Default
Enable SW1 Jumper at J5-1_J5-2 connects switch 1 to module pin-7 J5
Enable SW2
Jumper at J6-1_J6-2 connects switch 2 to IO-27
(Jumper at J14-15_J14-16 must be populated to connect IO27 to module
pin-18)
J6
Enable RGB-LED Jumper at J7-1_J7-2 connects RED LED to IO-23
(Jumper at J15-3_J14-5 must be populated to connect IO23 to module
pin-1)
J7-RED
Jumper at J7-3_J7-4 connects BLUE LED to IO-21
(Jumper at J16-1_J16-2 must be populated to connect IO21to module
pin-8)
J7-BLUE
Jumper at J7-5_J7-6 connects GREEN LED to IO-33 J7-GREEN
IO/Interface
select
Module pin to IO/Interface distribution J14 See Table 3
IO/Interface
select
Module pin to IO/Interface distribution J15 See Table 3
IO/Interface
select
Module pin to IO/Interface distribution J16 See Table 3
IO/Interface
select
Module pin to IO/Interface distribution J17 See Table 3
IO/Interface
select
Module pin to IO/Interface distribution J18 See Table 3
Enable VCC_IO Connects EVK internal 3.3 V to module pin-9 to supply module VCC_IO J25
Enable VCC Connects EVK internal 3.3 V to modle pin-10 to supply module VCC J26
Table 1: EVK-NINA-W1/EVK-NINA-B2 jumper descriptions
Figure 4: Jumper positions on the EVK
Middle row jumper pin Connected to
J14-1 Module pin-28
J14-3 Module pin-29
J14-5 Module pin-1
J14-7 Module pin-21
J14-9 Module pin-20
J14-11 Module pin-16
J15 (pin-1)
J16 (pin-1)
J17 (pin-1)
J14 (pin-1)
J7 (pin-1)
J26 (pin-1)
J25 (pin-1)
J18 (pin-1)
J6 (pin-1) J5 (pin-1)
Loading...