UBIQUITI UBI ES-10X Instructions

8-Port Gigabit Switch with PoE
Passthrough and 2 SFP Ports

Model: ES-10X

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgeSwitch®
10X. This Quick Start Guide is designed to guide you through
installation and also includes warranty terms.

Package Contents

EdgeSwitch 10X Wall Mount

Ground Screw Power Adapter

Screws (Qty. 2)

(24V, 1A)

Anchors (Qty. 2)

Cable Clip

Wall Mount

Installation Requirements

• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
power supply.

We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial‑grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit: www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the EdgeSwitch to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeSwitch itself should be housed inside a
protective enclosure.

Hardware Overview

Front Panel Ports

RJ45 Ports 1-8

Interface Description

RJ45 1‑8 RJ45 por ts support 10/100/1000 Ethernet

PoE In

(Port 1)

PoE Out

(Port 8)

SFP 9‑10 Hot‑swappable SFP ports support 1 Gbps

connections.
Supports 24V Passive PoE input.

Supports 24V Passive PoE passthrough.

connections. If you use a copper Ethernet
module (example: UF‑RJ45‑1G), power off
the EdgeSwitch before insertion; otherwise
there may be a device reboot.

SFP Ports 9-10

Front Panel Button

Reset

Button Description

To reset to factory defaults:

1. Disconnect power from the EdgeSwitch.

2. Reconnect power while holding the

Reset

Reset button. The port LEDs will light
up in sequential order (this takes
approximately five seconds).

3. When the port 1 LED flashes again,
release the Reset button.

Front Panel LEDs

System

System LED

State Status

Flashing White Bootup in Progress

White

Blue

Steady Blue
with Occasional
Flashing

Quickly Flashing
Blue

Alternating
Blue/White

Ready for Use

Not Connected to Ubiquiti Network
Management System (UNMS™)

Ready for Use

Connected to UNMS

Ready for Use

Unable to Connect to UNMS

Used to Locate a Device in UNMS

Firmware Upgrade in Progress

RJ45 LEDs

Speed/Link/Activity

LED

Speed/
Link/
Activity

SFP LEDs

LED

Link/
Activity

State Status

Off No Link

Amber Link Established at 10/100 Mbps

Amber
Flashing

Link Activity at 10/100 Mbps

Green Link Established at 1000 Mbps

Green
Flashing

Link Activity at 1000 Mbps

Link/Activity

State Status

Off No Link

Green Link Established at 1 Gbps

Green
Flashing

Link Activity at 1 Gbps

Back Panel

Power

Grounding Point

Interface Description

Power Connect the included Power Adapter to the

Grounding

Power port.
Ground bonding point for an optional

Point

ground wire.

Side Panel

Bracket Mounting

Holes

Ventilation

Holes

Hardware Installation

The EdgeSwitch can be placed on a horizontal surface,
mounted on a wall, or mounted in a rack (brackets not
included). The optional EdgeRouter™ Rackmount Kit, model
ER‑RMKIT, is sold separately.

Follow the Wall Mounting instructions to mount the
EdgeSwitch using the included screws and anchors.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.

WARNING: The EdgeSwitch ES‑10X must not be stacked.

Do not place it on top of another switch. Do not place
anything on top of the ES‑10X.

Wall Mounting

To mount the EdgeSwitch on a wall, you will need a drill, a

6mm drill bit, and a Phillips screwdriver.

1. Use a 6 mm drill bit to drill two holes 148 mm apart.

2. Insert the Wall Mount Anchors into the holes. Use a Phillips
screwdriver to secure a Wall Mount Screw to each anchor.
Leave a clearance of approximately 3 mm between each
screw head and its anchor.

148 mm

3 mm

Note: You can also mount the EdgeSwitch in a

vertical orientation.

3. Position the EdgeSwitch with the Ethernet ports facing
down. Place the wall‑mount slots of the EdgeSwitch over
the screw heads on the wall. Then slide the EdgeSwitch
down to lock it into place.

Grounding the EdgeSwitch (Recommended)

The EdgeSwitch is grounded through the Power Cord; however,
you can add optional ESD grounding for enhanced ESD
protection.

1. Attach the Ground Screw to secure a ground wire (not
included) to the Grounding Point.

2. Optional: To secure the Power Adapter cord, insert it
into the Cable Clip and secure the Cable Clip using the
GroundScrew.

3. Secure the other end of the ground wire to a grounding block.

Connecting Power

The EdgeSwitch can be powered by the included Power
Adapter or 24V Passive PoE.

Note: Only one power source can be used at any one

time. With both power sources connected, the input with
the highest voltage will be used; the other power source
defaults to backup.

Using the Power Adapter

1. Connect the Power Adapter to the Power port.

2. Connect the other end of the Power Adapter to a power
outlet.

Using PoE Input

1. Connect an Ethernet cable from your 24V PoE source to the
PoE In port on the EdgeSwitch.

1

2 5

3

PoE IN

4

876

9

PoE OUT

10

Connecting Ethernet

1. Connect an Ethernet cable from your DHCP server or LAN
system to any available port 1‑7 on the EdgeSwitch.

1

2 5

3

PoE IN

4

876

9

PoE OUT

10

2. Connect your 24V Passive PoE device to the PoE Out port
on the EdgeSwitch.

WARNING: Before enabling PoE passthrough in the

EdgeSwitch Configuration Interface, ensure that the
connected PoE device supports 24V Passive PoE.

1

2 5

3

PoE IN

4

876

9

PoE OUT

10

3. Connect your computer or host system and other devices
to the other ports on the EdgeSwitch.

Using SFP Ports

To use an SFP port:

1. Remove the protective plug covering the SFP port.

2. Plug a compatible fiber module into the SFP port.

1

2 5

3

PoE IN

4

876

9

PoE OUT

10

1000Mbps SM/SC 20KM DDM
Tx1550nm/Rx1310nm

3. Connect the fiber optic cable to the fiber module. Then
connect the other end of the cable to another fiber device.

1

2 5

3

PoE IN

4

876

9

PoE OUT

10

For information about compatible fiber SFP modules, visit:

ubnt.link/SFP_DAC_Compatibility

Accessing the Configuration Interface

The EdgeSwitch is set to DHCP by default, so it will try to
automatically obtain an IP address. If that fails, then it will use
the default fallback IP address, 192.168.1.20. Proceed to the
appropriate section, DHCP or “Fallback IP Address”:

DHCP

Use one of the following methods:

• Set up the DHCP server to provide a specific IP address to

the EdgeSwitch based on its MAC address (on the label).

• Let the EdgeSwitch obtain an IP address and then check the

DHCP server to see which IP address was assigned.

To log in, follow these steps:

1. Launch your web browser. Type the appropriate IP address
in the address field. Press enter (PC) or return (Mac).

2. The login screen will appear. Enter ubnt in the Username
and Password fields. Click Sign In. (When you sign in, you
agree to accept the Ubiquiti License Agreement.)

The EdgeSwitch Configuration Interface will appear.
Customize additional settings as needed. For 24V Passive PoE
configuration, refer to “Configuring PoE Settings”. For more
information, refer to the EdgeSwitch documentation, which is
available at www.ubnt.com/download/edgemax

Fallback IP Address

1. Ensure that your computer (or other host system) is
connected to the EdgeSwitch.

2. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type the appropriate IP address
in the address field (192.168.1.20 is the default fallback IP
address). Press enter (PC) or return (Mac).

https://192.168.1.20

4. The login screen will appear. Enter ubnt in the Username
and Password fields. Click Sign In.

5. The EdgeSwitch Configuration Interface will appear. Click
the System Settings tab.

6. Change the IP Address to a unique IP address. Click Apply.

Note: If you change the IP settings, then the session

will be cut off, and you will need to reconnect to the
EdgeSwitch using the new IP address.

Customize additional settings as needed. For 24V Passive PoE
configuration, refer to “Configuring PoE Settings”. For more
information, refer to the EdgeSwitch documentation, which is
available at www.ubnt.com/download/edgemax

UNMS Management

You can manage your device using UNMS, which lets you
configure, monitor, upgrade, and back up your devices using a
single application. Get started at www.unms.com

Configuring PoE Settings

The PoE setting for port 8 is set to Off by default.

WARNING: Before activating PoE, ensure that the

connected device supports passive PoE and the
supplied voltage.

On the Dashboard tab, click the PoE setting of port 8. Then
select 24V.

Specifications

Dimensions 207 x 31.1 x 90 mm (8.15 x 1.22 x 3.54")

Weight 500 g (1.10 lb)

Total Non‑Blocking
Throughput

Switching Capacity 20 Gbps

Forwarding Rate 14.88 Mpps

Max. Power Consumption
(Excluding PoE Output)

Power Method 24VDC, 1A or

Supported Voltage Range 9 ‑30VDC

Power Supply 24VDC, 1A Power Adapter (Included) or

LEDs

System
RJ45 Data Ports
SFP Data Ports

Networking Interfaces (8) 10/100/1000 Mbps RJ45 Ports

Management Interface Ethernet In‑Band

Certications CE, FCC, IC

ESD/EMP Protection Air: ± 24 kV, Contact: ± 24 kV

Operating Temperature ‑10 to 50° C (14 to 122° F)

Operating Humidity 5 to 95% Noncondensing

Shock and Vibration ETSI300‑019‑1.4 Standard

PoE Interface 24VDC Passive PoE (Pins 4, 5+; 7, 8‑)

Max. Passive PoE Wattage
per Port

24V Passive PoE Voltage Range 24V

ES‑10X

PoE (Port 8)

10 Gbps

24V Passive PoE

24V Passive PoE

Status

Link/Speed/Activity

Link/Activity

(2) 1 Gbps SFP Ports

8W

15W

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Failure to provide proper ventilation may

cause fire hazard. Keep at least 20 mm of clearance next
to the ventilation holes for adequate airflow.

WARNING: To reduce the risk of fire or electric shock, do

not expose this product to rain or moisture.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from
lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2‑wire
outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the
equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short‑circuit backup
protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

www.ubnt.com/support/warranty/

The limited warranty requires the use of arbitration to resolve disputes on
an individual basis, and, where applicable, specify arbitration instead of
jury trials or class actions.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including
interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operations of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.

ISED Canada

CAN ICES‑3(A)/NMB‑3(A)

This Class A digital apparatus complies with Canadian CAN ICES‑003.

CAN ICES‑3(A)/NMB‑3(A)

Cet appareil numérique de la classe A est conforme à la norme NMB‑003
du Canada.

Australia and New Zealand

Warning: This equipment is compliant with Class A of CISPR 32.
In a residential environment this equipment may cause radio
interference.

CE Marking

CE marking on this product represents the product is in compliance with all
directives that are applicable to it.

RoHS/WEEE Compliance Statement

English

European Directive 2012/19/EU requires that the equipment bearing
this symbol on the product and/or its packaging must not be disposed
of with unsorted municipal waste. The symbol indicates that this
product should be disposed of separately from regular household waste
streams. It is your responsibility to dispose of this and other electric and
electronic equipment via designated collection facilities appointed by the
government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human
health. For more detailed information about the disposal of your old
equipment, please contact your local authorities, waste disposal service, or
the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2012/19/EU verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem
Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall
entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt
von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es
liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische
und elektronische Geräte über die dafür zuständigen und von der
Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu
entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche Gesundheit
zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer
Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder
städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das
Produkt erworben haben.

Español

La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en
el propio aparato y/o en su embalaje no deben eliminarse junto con otros
residuos urbanos no seleccionados. El símbolo indica que el producto
en cuestión debe separarse de los residuos domésticos convencionales
con vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos
de recogida que ponen a su disposición el gobierno y las autoridades
locales. Al desechar y reciclar correctamente estos aparatos estará
contribuyendo a evitar posibles consecuencias negativas para el medio
ambiente y la salud de las personas. Si desea obtener información más
detallada sobre la eliminación segura de su aparato usado, consulte a las
autoridades locales, al servicio de recogida y eliminación de residuos de su
zona o pregunte en la tienda donde adquirió el producto.

Français

La directive européenne 2012/19/UE exige que l’équipement sur lequel
est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté
avec les autres ordures ménagères. Ce symbole indique que le produit
doit être éliminé dans un circuit distinct de celui pour les déchets des
ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout
autre matériel électrique ou électronique par les moyens de collecte
indiqués par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme ont pour
but de lutter contre l’impact néfaste potentiel de ce type de produits
sur l’environnement et la santé publique. Pour plus d’informations sur le
mode d’élimination de votre ancien équipement, veuillez prendre contact
avec les pouvoirs publics locaux, le service de traitement des déchets, ou
l’endroit où vous avez acheté le produit.

Italiano

La direttiva europea 2012/19/UE richiede che le apparecchiature
contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non
siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica
che questo prodotto non deve essere smaltito insieme ai normali rifiuti
domestici. È responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante le specifiche
strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il
corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze
potenzialmente negative per l’ambiente e per la salute dell’essere umano.
Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti
pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel
quale avete acquistato il prodotto.

Declaration of Conformity

български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство

ES-10X е в съответствие със съществените изисквания и други приложими разпоредби на
Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие
може да се намери на следния интернет адрес:

Hrvatski [Croatian] UBIQUITI NETWORKS ovim putem izjavljuje da je ovaj uređaj ES-10X

sukladan osnovnim zahtjevima i ostalim bitnim odredbama Direktiva 2014/30/EU,
2014/35/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi:

www.ubnt.com/compliance

Čeština [Czech] UBIQUITI NETWORKS tímto prohlašuje, že toto ES-10X zařízení, je ve

shodě se základními požadavky a dalšími příslušnými ustanoveními směrnic 2014/30/EU,
2014/35/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese:

www.ubnt.com/compliance

Dansk [Danish] Hermed, UBIQUITI NETWORKS, erklærer at denne ES-10X enhed,

er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiver
2014/30/EU, 2014/35/EU. EU-overensstemmelseserklæringens fulde tekst kan findes på følgende
internetadresse:

www.ubnt.com/compliance

Nederlands [Dutch] Hierbij verklaart UBIQUITI NET WORKS, dat deze ES-10X apparaat, in

overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijnen
2014/30/EU, 2014/35/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden
geraadpleegd op het volgende internetadres:

English

Hereby, UBIQUITI NETWORKS, declares that this ES-10X device, is in compliance with
the essential requirements and other relevant provisions of Directives
The full text of the EU declaration of conformity is available at the following internet address:

www.ubnt.com/compliance

Eesti keel [Estonian] Käesolevaga UBIQUITI NETWORKS kinnitab, et antud ES-10X seade,

on vastavus olulistele nõuetele ja teistele asjakohastele sätetele direktiivide 2014/30/EL,
2014/35/EL. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil:

www.ubnt.com/compliance

Suomi [Finnish] Täten UBIQUITI NETWORKS vakuuttaa, että tämä ES-10X laite, on yhdenmukainen

olennaisten vaatimusten ja muiden sitä koskevien direktiivien 2014/30/EU, 2014/35/EU.
EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa
internetosoitteessa:

Français [French] Par la présente UBIQUITI NETWORKS déclare que l’appareil ES-10X, est

conforme aux exigences essentielles et aux autres dispositions pertinentes des directives
2014/30/UE, 2014/35/UE. Le texte complet de la déclaration UE de conformité est disponible à
l’adresse internet suivante:

Deutsch [German] Hiermit erklärt UBIQUITI NET WORKS, dass sich dieses ES-10X

Gerät, in Übereinstimmung mit den grundlegenden Anforderungen und den anderen
relevanten Vorschriften der Richtlinien 2014/30/EU, 2014/35/EU befindet. Der vollständige
Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:

www.ubnt.com/compliance

Ελληνικά [Greek] Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή ES-10X,

είναι σε συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις των οδηγιών
2014/30/EE, 2014/35/EE. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην
ακόλουθη ιστοσελίδα στο διαδίκτυο:

Magyar [Hungarian] Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a ES-10X készülék

megfelel az alapvető követelményeknek és más vonatkozó 2014/30/EU, 2014/35/EU irányelvek
rendelkezéseit. Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes
címen:

Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta ES-10X tæki er í samræmi við

grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB
samræmisyfirlýsing er að finna á eftirfarandi netfangi:

www.ubnt.com/compliance

www.ubnt.com/compliance

www.ubnt.com/compliance

www.ubnt.com/compliance

www.ubnt.com/compliance

2014/30/EU, 2014/35/EU

www.ubnt.com/compliance

www.ubnt.com/compliance

.

Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo ES-10X,

è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE,
2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente
indirizzo Internet:

Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka ES-10X ierīce, ir saskaņā ar

būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES. Pilns
ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē:

Lietuvių kalba [Lithuanian] UBIQUITI NETWORKS dek laruoja, kad šis ES-10X įrenginys atitinka

esminius reikalavimus ir kitas 2014/30/ES, 2014/35/ES Direktyvų nuostatas. Visas ES atitikties
deklaracijos tekstas prieinamas šiuo interneto adresu:

Malti [Maltese]

mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttivi 2014/30/UE, 2014/35/UE.
Id-dikjarazzjoni tal-konformità tista’ tiġi kkonsultata minn www.ubnt.com/compliance

Norsk [Norwegian]

med de grunnleggende kravene og andre relevante bestemmelser i direktivene 2014/30/EU,
2014/35/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende
internettadresse: www.ubnt.com/compliance

Polski [Polish] Niniejszym, UBIQUITI NETWORKS, oświadcza, że urządzenie ES-10X, jest zgodny

z zasadniczymi wymaganiami oraz pozostałymi stosownymi postanowieniami Dyrektyw
2014/30/UE, 2014/35/UE
adresem internetowym:

Português [Portuguese] UBIQUITI NETWORKS declara que este dispositivo ES-10X, está

conforme com os requisitos essenciais e outras disposições das Directivas
2014/35/UE
endereço de Internet:

Română [Romanian] Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv ES-10X este

în conformitate cu cerințele esențiale și alte prevederi relevante ale Directivelor
2014/35/UE
internet:

Slovenčina [Slovak]

je v súlade so základnými požiadavkami a ďalšími relevantnými ustanoveniami smernice
2014/30/EÚ, 2014/35/EÚ

www.ubnt.com/compliance

Slovenščina [Slovenian]

skladu z obveznimi zahtevami in drugimi ustreznimi določbami direktiv 2014/30/EU in
2014/35/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu:

www.ubnt.com/compliance

Español [Spanish] Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo

ES-10X, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de las Directivas
conformidad está disponible en la dirección Internet siguiente:

Svenska [Swedish] Härmed UBIQUITI NETWORKS, intygar att denna ES-10X enhet är i

överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiven
överensstämmelse finns på följande webbadress:

www.ubnt.com/compliance

www.ubnt.com/compliance

Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz ES-10X huwa konformi

Herved UBIQUITI NETWORKS, erklærer at denne ES-10X enheten, er i samsvar

. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym

www.ubnt.com/compliance

. O texto integral da declaração de conformidade está disponível no seguinte

www.ubnt.com/compliance

. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă

www.ubnt.com/compliance

Týmto UBIQUITI NETWORKS, prehlasuje, že toto ES-10X zariadenie,

. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese:

Družba UBIQUITI NETWORKS izjavlja, da je naprava ES-10X v

2014/30/UE, 2014/35/UE

2014/30/EU, 2014/35/EU

www.ubnt.com/compliance

2014/30/UE,

2014/30/UE,

. El texto completo de la declaración UE de

www.ubnt.com/compliance

. Den fullständiga texten till EU-försäkran om

www.ubnt.com/compliance

Online Resources

Support help.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com

www.ubnt.com

Ubiquiti Networks, Inc.

685 Third Avenue, 27th Floor

New York, NY 10017

USA

©2018‑2019 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti,

UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX,

EdgeOS, EdgeRouter, EdgeSwitch, TOUGHCable, and UNMS are trademarks

or registered trademarks of UbiquitiNetworks, Inc. in the United States

and in other countries. All other trademarks are the property of their
respective owners. JL010819