Ubiquiti RD-2G24 Quick Start Guide

airMAX™ Carrier Class 2x2 PtP Bridge Dish Antenna
Model: RD-2G24
Introduction
Thank you for purchasing the Ubiquiti Networks™ RocketDish™,
an airMAX
Carrier Class 2x2 PtP Bridge Dish Antenna. This Quick Start Guide is designed to guide you through the installation of the antenna. This Quick Start Guide also includes the warranty terms and is for use with the RocketDish, model RD-2G24.
Package Contents
Dish Reflector Antenna Feed Mount Bracket Pole Clamps
Stabilizer Brackets
(Qty. 2)
M10x100 Bolts
(Qty. 2)
Products may be different from pictures and are subject to change without notice.
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. It is the customer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements.
Elevation Rod M10x150 Carriage Bolts
M10x25 Carriage Bolts
(Qty. 3)
M4 Bolts
(Qty. 4)
(Qty. 4)
(Qty. 2)
airMAX™ Carrier Class 2x2 PtP Bridge Dish Antenna
Model: RD-2G24
Quick Start
Guide
Installation Requirements
• RocketM2 (sold separately)
• Phillips #1 screwdriver
• 16 mm or 5/8 in. wrench
• 24 mm wrench
• Shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial-grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable
Hardware Overview
Elevation Rod
Pole Clamp
Antenna Feed
Main Mounting Bracket
Rocket Mounting Bracket
Pole Clamp
Stabilizer Brackets
Fully Assembled Back View
Hardware Installation
Important: Handle the Dish Reflector with care.
Deformations in its shape may reduce the RocketDish's effectiveness.
1. Each M4 Bolt includes a lock washer. Remove these and use
them to secure the bolts when assembling.
2. The Dish Reflector and Antenna Feed are keyed so the
Antenna Feed can only be installed in a single orientation. Attach the Antenna Feed to the Dish Reflector in the following steps:
a. Line up the alignment pin on the Dish Reflector with the
hole on the Antenna Feed.
b. Insert the four M4 Bolts into the Antenna Feed and Dish
Reflector.
c. Tighten the four M4 Bolts.
Important: Do not handle the RocketDish by the Antenna
Feed once the feed is connected.
3. Attach the RocketM to the Dish Reflector.
a. Align the mounting tabs on the back of the RocketM
with the Rocket Mounting Bracket located below the Antenna Feed.
b. Slide the RocketM down to lock it into place.
4. Attach the RF Cables to the connectors labeled Chain 0 and
Chain 1 on the RocketM.
5. The Elevation Rod includes washers and nuts. Remove one
washer, one spring lock washer, and one nut. Use them to secure the Elevation Rod when assembling.
6. Attach the Elevation Rod to the Main Mounting Bracket.
a. Insert the Elevation Rod into the Main Mounting Bracket. b. Secure the Elevation Rod with the washer, spring lock
washer, and nut.
7. Each M10x150 Carriage Bolt includes a washer, spring lock
washer, and nut. Remove these and use them to secure the bolts when assembling in step 13.
8. Insert the four M10x150 Carriage Bolts into the Main
Mounting Bracket.
Loading...
+ 14 hidden pages