Ubiqconn Technology CARPOTE00R00 Users Manual
Caarrppoo--TTEE0000
C
R0000
R
UUsseerr GGuuiiddee
VVeerrssiioonn:: 11..00
Carpo-TE00R00 User Guide
Introduction
1. Please read these safety instructions carefully.
2. Please keep this User’s Manual for later reference.
3. Please disconnect this equipment from connecter before
cleaning. Don’t use liquid or prayed detergent for cleaning.
User moisture sheet or cloth for cleaning.
4. Make sure the equipments are connected to the power source
with the correct voltage, frequency, and ampere.
5. All cautions and warnings on the equipment should be noted.
6. Never pour any liquid into opening: this could cause fire or
electrical shock.
7. Never open the equipment. For safety reason, the equipment
should only be opened by qualified service personnel.
8. If one of the following situations arises, get the equipment
checked by a service personnel:
a. Liquid has penetrated into the equipment.
b. The equipment has been exposed to moisture.
c. The equipment has not worked well or you cannot get it
work according to user manual.
d. The equipment has dropped and damaged. If the
equipment has obvious sign of breakage.
0
Carpo-TE00R00 User Guide
9. Caution on use of battery: User the battery recommended by
the manufacturer or the same type of battery installed by the
manufacturer. If incorrect battery is used, it may cause
explosion or fire hazard. Recycle or discard used batteries
according the manufacturer’s instruction or your local
authority.
10. The computers use nonvolatile memory that requires a battery
to retain system information when power is removed. The 3V
lithium battery is on the system board. The battery life
depends on the amount of time the computer is powered on. If
the computer does not display the correct time and date,
replace the battery.
IMPORTANT：Loss of BIOS settings occurs when the battery is
removed. BIOS settings must be reconfigured whenever the
battery is replaced.
WARNING：A risk of fire and chemical burn exists if the battery
is not handled properly. Do not disassemble, crush, puncture, or
short external contacts, or expose the battery to temperatures
higher than 60 °C (140 °F). Do not dispose of a used battery in
water or fire.
CAUTION：Danger of explosion if battery is incorrectly replaced.
0
Carpo-TE00R00 User Guide
Replace only with same or equival ent type recommended by the
manufacturer. Discard used batteries according to the
manufacturer’s instructions.
FCC Compliance Statement
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
0
Carpo-TE00R00 User Guide
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter has been demonstrated co-location
compliance requirements with Wi-Fi, Bluetooth SiP (System in
Package) module. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This device was
tested for typical hand held operations with the device
contacted directly to the human body to the back side of the
tablet pc. To maintain compliance with FCC RF exposure
compliance requirements, avoid direct contact to the
transmitting antenna during transmitting.
EEuurrooppee –– EEUU DDeeccllaarraattiioonn ooff CCoonnffoorrmmiitty
This device complies with the essential requirements of the
R&TTE Directive 1999/5/EC and EMC directive 2004/108/EC. The
following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the
R&TTE Directive 1999/5/EC and EMC directive 2004/108/EC:
y
0
Carpo-TE00R00 User Guide
< EN 55022: 2006 +A1: 2007
< EN 61000-3-2 : 2006
< EN 61000-3-3 : 1995 + A1 : 2001 + A2 : 2005
< EN 55024: 1998 + A1: 2001 + A2: 2003
(IEC 61000-4-2: 2008;
IEC 61000-4-3: 2006 + A1:2007;
IEC 61000-4-4: 2004;
IEC 61000-4-5: 2005;
IEC 61000-4-6: 2003 + A1: 2004 +A2: 2006;
IEC 61000-4-8: 1993 +A1: 2000;
IEC 61000-4-11: 2004)
< EN 60950-1: 2001
Safety of information technology equipment
< EN 300 328 V1.7.1: 2006
< EN 301 489-17 V2.1.1: 2009 and EN 301 489-1 V1.8.1: 2008
< EN 62311: 2008
This device is a 2.4GHz wideband transmission system
(transceiver), intended for use in all EU member states and EFTA
countries under the following conditions and/or with the follo wing
restrictions:
< In Italy the end-user should apply for a license at the national
spectrum authorities in order to obtain authorization to use
the device for setting up outdoor radio links and/or for
supplying public access to telecommunications and/or
0
Carpo-TE00R00 User Guide
network services.
< This device may not be used for setting up outdoor radio links in
France and in some areas the RF output power may be limited to 10
mW EIRP in the frequency range of 2454 – 2483.5 MHz. For det ailed
information the end-user should contact the national spectrum
authority in France.
0
Carpo-TE00R00 User Guide
TableofContents
Introduction ...........................................................0
Chapter 1 General Information.............................0
1.1. Introduction..........................................................................................0
1.2. Specification.........................................................................................0
1.2.1. Main System..............................................................................................0
1.2.2. I/O Interface...............................................................................................0
1.2.3. In Front Control..........................................................................................0
1.2.4. Power Management ...................................................................................0
1.2.5. Environment...............................................................................................0
1.2.6. Material......................................................................................................0
1.2.7. Operation OS.............................................................................................0
1.2.8. Certifications..............................................................................................0
1.2.9. Optional: Internal Module...........................................................................0
1.2.10. Optional: External Accessories................................................................0
1.2.11. Optional: Packing Lists.............................................................................0
0
Carpo-TE00R00 User Guide
1.3. Packing List..........................................................................................0
1.4. Dimensions...........................................................................................0
Chapter 2 System Setup.......................................0
2.1. Exploring Your Carpo-TE00R00..........................................................0
2.1.1. The front side of the Carpo-TE00R00..................................................0
2.1.2. The rear side of the Carpo...................................................................0
2.1.3. The right side of the Carpo...................................................................0
2.1.4. The left side of the Carpo.....................................................................0
2.1.5. The bottom side of the Carpo...............................................................0
2.2. Preparing for Installation.....................................................................0
2.2.1. Installing the Rubber Bumpers.............................................................0
2.2.2. Removing the Rubber Bumpers...........................................................0
2.2.3. Plugging to the DC supply ...................................................................0
2.2.4. Starting Your System ...........................................................................0
2.2.5. Connecting the keyboard and mouse ..................................................0
2.3. Using Your Android Operating System..............................................0
2.3.1. Application Control...............................................................................0
2.3.2. Screen Hotkey Utility for function controls ...........................................0
0
Carpo-TE00R00 User Guide
2.3.3. Menu Controls......................................................................................0
Chapter 3 Using the Carpo-TE00R00...................0
3.1. Introduction..........................................................................................0
3.2. Using the USB Ports............................................................................0
3.3. Using the External Audio System.......................................................0
3.4. Installing the Battery............................................................................0
3.5. U s i ng a Barcode Sc a n n e r M o d ul e ( o p t i o n a l )...........................................45
3.6. U si n g a M S R M o d u l e ( o p t i o n a l )...............................................................47
3.7. Using the Docking Stand (optional)....................................................49
3.9.1. The right side of the Docking Stand....................................................
3.9.2. The rear side of the Docking Stand.....................................................
51
51
Chapter 4 Maintenance.......................................03
4.1. Maintaining the Battery .....................................................................03
4.2. Maintaining the LCD Display.............................................................04
4.3. Cleaning the Carpo-TE00R00............................................................04
0
Carpo-TE00R00 User Guide
CChhaapptteerr 1
1
GeneralInformation
n
11..11.. IInnttrroodduuccttiioonn
Carpo-TE00R00 semi-rugged tablet PC is TI Cortex-A8 DM3730 1.0GHz
processor core architecture based Semi-rugged Tablet PC with a bright
10.1-inch LED backlight LCD display. The powerful CPU brings the most
dynamic applications to life without sacrifices to any industrial reliability.
Delivery a variety of connectivity features, built-in USBs, Microphone and
Headphone port. It is ideal for an all-around system performance.
Furthermore, Carpo-TE00R00 semi-rugged tablet PC is equipped with
fanless design.
11..22.. SSppeecciiffiiccaattiioon
The Carpo-TE00R00 semi-rugged tablet PC is a flexible, multi-functional
flat tablet PC. With following specifications that can be applied in diverse
operational environments and implemented in multi-faceted applications.
1.2.1. Main System
z Platform:
< TI Cortex-A8 Platform
0
Carpo-TE00R00 User Guide
z MPU :
< TI Cortex-A8 DM3730 1.0GHz
< Processor packing : Micro-FCBGA
< Cores : Single Core
< On-die L2 Cache : 256KB
z Graphics :
< TI SGX Embedded, H.264, MPEG 2. MPEG 4, JPEG and G711
supported
z System Memory :
< 256MB LPDDR on board
z Flash Memory :
< 8GB moviNand on board
z Storage :
< 1 x 8G SLC SDHC Card
z LCD Screen :
< Panel size : 10.1-inch LED Backlight LCD
< Brightness : 200nits
< Resolution : 1024 RGB(W) x 600(H) WVGA
z Touch Panel :
< 5-wire Resistive Touch Panel
z Sunlight Readable :
< Transflective plus type
z Audio :
< Internal Speaker : 2 x High Quality Speakers (2W)
< Internal Microphone : 1 x in front Bezel
0
Carpo-TE00R00 User Guide
z Communication :
< 1 x Wireless IEEE 802.11 b/g/n
< 1 x Bluetooth 2.1 + EDR
z Webcam :
< Front Bezel: 1.3 Mega-pixel Camera audio input (Microphone)
functions.
< Rear Bezel: 2 Mega-pixel Camera, LED auxiliary light.
1.2.2. I/O Interface
z External I/O :
< 2 x USB 2.0 type A
< 1 x Headphone Jack
< 1 x Microphone Jack
< 1 x Docking Connector
< 1 x DC-Jack
z LED Status Indicator:
< Power LED Status: 1 x Green/Orange/Red Colors
< Storage LED Status: 1 x Blue Color
< Wi-Fi LED Status: 1 x Blue Color
1.2.3. In Front Control
z Switch :
< 1 x Power Button
< 1 x Lock Button
< 1 x RF Button
z Button :
0
Carpo-TE00R00 User Guide
< Navigation Buttons : 5+ Way navigation button with integrated
enter button
< Program Function Buttons : 5 x Function keys (Programmable)
< Barcode Buttons : 2 x Trigger Buttons (Programmable)
z Sensor :
< 1 x Light Sensor
1.2.4. Power Management
z Power Adapter :
< AC to DC, 19VDC@3.42A, 65W
< AC 100V ~ 240V, 50~60Hz input
< 19 DC-in
z Battery (Internal Battery) :
< Internal Smart Lithium Polymer Battery, 3800mAh
1.2.5. Environment
z Operation Temperature :
< 0°C to +45°C (MIL-STD-810G Method 501.5 and 502.5)
z Storage Temperature :
< -20°C to +60°C (MIL-STD-810G Method 501.5 and 502.5)
z Humidity :
< 5-90% without condensation (MIL-STD-810G Method 507.5)
z Drop :
< 4-ft drop to Plywood (MIL-STD-810G Method 516.6 Procedure
IV)
z Vibration :
0
Carpo-TE00R00 User Guide
< Operating : SD (MIL-STD-810G Method 514.6 Category 4 Fig
514.6C-3)
z Mechanical Shock :
< Operating : 20g, 11ms, Terminal sawtooth
< Non-operating : 40g, 11ms, Terminal sawtooth (MIL-STD-
810G Method 516.6 Procedure I)
z Water/Dust Resistance : IP54 equivalent
1.2.6. Material
z Chassis :
< Semi-Rugged Tablet PC Slate
z Enclosure :
< PC/ABS Plastic, PC/ABS and TPU Double Injection with
Protective Rubber Grips Set
z Dimension (W x H x D mm) :
< 277.8 x 206 x 26.5mm
z Weight :
< Approximate 1.1kg (with internal battery)
1.2.7. Operation OS
z Win CE 6.0, Android 2.3 and Linux BSP
1.2.8. Certifications
z EMI :
< FCC part 15 Class B, UL
< CE (EN55022 / EN55024)
z Safety :
0
Carpo-TE00R00 User Guide
< CE (EN60950-1)
z RF :
< FCC part 15 subpart C
< ETSI (EN300 328 / EN301 489-1 / -17)
z SAR :
< FCC SAR (OET 65 C)
< CE SAR (EN62311)
1.2.9. Optional: Internal Module
z TPM :
< 1 x Compatible with TPM1.2
1.2.10. Optional: External Accessories
z MSR :
< Reference Standards :
ANSI/ISO Standards 7810,7811-1/6, 7813
JIS II
< Decoding Method :
ISO Track1 - IATA , Track2 - ABA and Track3 – THRIFT
z Barcode Scanner :
< Decoded Mode :
1D Symbologies : EAN/UPC, RSS, Code 39, Code 128,
UCC/EAN 128, ISBN, ISBT, Interleaved, Matrix, Industrial
and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI,
Plessey, Telepen, postal codes.
2D Symbologies: Data Matrix, PDF417, Micro PDF 417,
Maxicode, QR, Aztec, EAN.UCC composite.
0
Carpo-TE00R00 User Guide
z GPS :
< Channel :
50 channel all-in-view tracking
1 x Double Color LED (Red & Blue)
< OS :
Win CE 6.0 support
z Desktop Docking :
< Win CE 6.0 : 4 x USB2.0 type A, 1 x Ethernet, 1 x Kensington
and 1 x DC Jack support
< Android 2.3 : 4 x USB2.0 type A, 1 x Kensington and 1 x DC
Jack support
z External Battery Kits :
< External Battery Pack :
Hot-swappable Lithium Polymer battery pack - doubles
duration of mobile operation, 4000mAh
< External Battery Charger :
Recharges external battery pack
< Vehicle Application Accessories :
Vehicle Mounting Docking :
D Win CE 6.0 : 4 x USB2.0 type A, 2 x RS232, 1 x
10/100Mbps Ethernet and DC-Jack support
D Android 2.3 : 4 x USB2.0 type A and DC-Jack support
D 75 x 75/100 x 100mm Vesa Mount Holes support
D 6VDC to 36VDC Input; 19 V@1.57A Max., total output
30W
D Cigarette lighter plug power cord
0
Loading...