Ubee Interactive UBC1301 Users Manual

!

www.ubeeinteractive.com

UBC1301-AA00

D3.1 Advanced Wireless Voice Gateway

Quick Installation Guide

Subscriber

Grounding the Device: Install the cable modem to include

grounding the coaxial cable to the earth as close as practical to
the building entrance per ANSI/NFPA 70 and the National
Electrical Code (NEC, in particular, Section 820.93, Grounding of
the Outer Conductive Shield of a Coaxial Cable). The device is
designed for IT power systems with phase-to-phase voltage at
120V.

This unit requires a 100-240V, 50-60Hz power cable. Power cable
must be keyed for proper polarization, and must be fully inserted
to contact the back of the power connector port to ensure snug
connection. Do NOT use any other power cable.

Disconnecting the Device: If the cable modem becomes damaged

or encounters some other abnormality, disconnect the power plug
from the AC wall outlet immediately.

Temperature and Altitude: Install the device in a location not to

exceed the maximum temperature of 104 Fahrenheit (40 Celsius).
Regular operating altitude is 2000 m, and maximum operating
altitude is 4500 m.

•

SAFETY NOTICES

•

PREPARING FOR INSTALLATION

✓

Locate the RF (coaxial) cable connector on the wall.

✓

Verify the power outlet is working and is wired correctly. Place
your cable modem within a proper distance from the outlet.

2. Connect the Ethernet cable (supplied) to the Ethernet port on

the back panel of the modem and connect the other end to to
the Ethernet port of a PC. Use a Category 5e or Category 6
Ethernet cable with RJ-45 connectors to ensure Gigabit
Ethernet speeds (when the computer supports it).

3. Connect an RJ-11 phone cable (not supplied) to the TEL1 port

on the modem (when provisioned for voice service as specified
by the service provider), and connect the other end to the
phone port of the telephone. If voice service is not provisioned
through the service provider, telephone service is not available.

4. Connect the power cord (supplied) to the POWER port.

Connect the other end to a power outlet.

1

UBC1301-AA00
Advanced Wireless Voice Gateway

RJ-45

Analog Phones

RJ-11

Cable/RF

Device must be installed vertically to

obtain optimum wireless performance.

Connect a PC or Ethernet enabled device (wireless
switch or router). A PC should be connected for
initial device installation and configuration.

2

1

3

4

1.

Connect the coaxial cable (not supplied) to the CABLE
connector on the rear panel of the modem and connect the
other end to the cable wall outlet. Do not bend or over tighten
the cables, as this may strain the connector and cause damage.
To connect a modem and a television to the same wall outlet,
you must use a cable line splitter (not included).

•

INSTALLING THE MODEM

!

•

DEVICE WALL MOUNT INSTRUCTIONS

You can mount the UBC1301-AA00 on a wall using the 2 mounting
brackets on the side of the device. Two round or pan head screws
are recommended. See the figure below for measurements.

www.ubeeinteractive.com

2

Label

Size in Millimeters (mm)

A

6.65 +/- 0.35

B

1.9 +/- 0.15

C

19.0 +/- 1.2

UBC1301-AA00 Quick Installation Guide

NOTE to CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV systems installer's
attention to section 820-93 of the National Electric Code, which
provides guidelines for proper grounding and in particular,
specify that the Coaxial cable shield shall be connected to
grounding system of the building, as close to the point of cable
entry as practical.

Note: The screws should protrude from the wall so you can fit
the device between the head of the screws and the wall. If
you install the screws in drywall, use hollow wall anchors to
ensure the unit does not pull away from the wall due to
prolonged strain from the cable and power connectors.

2.

Mount the device on the wall.

To mount the device on a wall:

1. Install the 2 screws horizontally on the wall 153 mm (5.9

inches apart.