Tzora Lexis Light, Easy Travel Lexis Light User Manual

Lexis Light

USER’S MANUAL

Lexis Light – ET1B User’s Manual T. Rev. 0512 PM 2

Lexis Light – ET1B User’s Manual T. Rev. 0512 PM 3

Table of contents:

Page

1. Introduction 4

2. Safety 4

3. System components 5

4. Assembly and Folding Instructions 7

5. Operating your Lexis Light 10

6. Moving and Transporting your Lexis Light 14

7. Helpful Hints for Everyday Use 16

8. General Maintenance and Inspection 17

9. EMI – Electromagnetic interference 19

10. Fault Finding 22

11. Disposal and Recycling 23

12. Technical Data 23

NOTE: Design details may change without notice.

Lexis Light – ET1B User’s Manual T. Rev. 0512 PM 4

1. INTRODUCTION

The Lexis Light is intended for use by individuals that are able to
walk, but suffer from mild mobility limitations. The user must have sufficient
arm and leg strength to get on and off the Lexis Light alone and to
safely steer under all driving conditions. The Lexis Light is intended
for indoor and restricted outdoor use on pavements or paved footpaths only
during daylight hours. The Lexis Light must not be used as a
transportation vehicle on roads or freeways used by cars. The Lexis Light
does not have lights and reflectors and therefore must not be used in
the dark or in limited visibility conditions.

2. SAFETY

During your initial use of the Lexis Light we recommend caution as

you practice operating the unit in various situations. Keep the speed at a

reduced level until you are comfortable controlling the scooter. Follow the

safety tips and instructions and you will be comfortable maneuvering through

doorways, on and off lifts, over moderate terrain and up and down ramps.

These safety considerations and tips will help you to operate the Lexis Light

safely. The Lexis Light is a powerful electric vehicle these

rules will help you prevent personal injury and damage to your scooter.

1. Read this manual and all labels before operating.

2. Do not carry passengers or exceed the maximum weight capacity.

3. Do not mount or dismount the Lexis Light unless it has come to a

full stop and is turned off.

4. Do not back up on to uneven inclines or surfaces.

5. Always switch the speed selector to low when driving in a confined space.

6. Always reduce speed when turning.

7. Do not operate your scooter when under the influence of alcohol,

medications or drugs that may impair your safety.

8. Always keep your feet on the foot platform when driving.

Lexis Light – ET1B User’s Manual T. Rev. 0512 PM 5

9. Do not sit on the scooter while being transported in a moving vehicle.

Always fold down and secure your Lexis Light and transfer

yourself to a vehicle seat.

3. SYSTEM COMPONENTS AND DETAILS

3.1. Lexis Light parts – (Figure 1)

1. Battery pack (detachable) 11. Rear wheel

2. Front column (detachable) 12. Folded frame lock/release pin

3. Column lock/release triggers 13. Unfolded frame lock/release pin

4. Controller cover 14. Utility basket (holding capacity

5. Charging socket (Fig. 1A) 20lbs/9kg)

6. Front drive wheels 15. Charger and connecting cables

7. Foot platform (Fig. 1B)

8. Seat shell 16. Control Panel

9. Seat cushions 17. Freewheel switch

Lexis Light – ET1B User’s Manual T. Rev. 0512 PM 6

3.2. Control Panel – Figure 2

1. On-Off Switch

2. Hand control lever (right and left)

3. Speed adjusting knob

4. Indicator light (LED)

5. Battery Gauge

6. Hand-grips

3.3. Lexis Light Optional Accessories:

1. Extra battery pack

BELL: If the user requires an audible warning device, a standard bicycle

bell can be attached to the handlebar.

Lexis Light – ET1B User’s Manual T. Rev. 0512 PM 7

4. ASSEMBLY AND FOLDING INSTRUCTIONS

4.1. Assembling your Lexis Light

Unfolding Rear Frame

Pull on the folded frame lock pin ring

(Fig. 4/1) to release the foot platform

and unfold the frame. Pull the seat

backrest (Fig. 4/2) and lift it to the

upright position. Ensure that the

unfolded frame lock pin secures the

platform in the horizontal position.

Unfolding Front Column

Pull the column lock trigger (Fig. 4/3)

upward towards the handle to release

the tilt lock. Move the drive unit away

from the column (all the way) to open

the quick-release housing. This is the

column “detach” position.

Connecting the Front Column to the

Rear Frame

Position the column in the “detach”

position. Lift the front of the foot

platform and insert connection pin into

the quick-release housing on the drive

unit. This may be done without bending

down by lifting the front of the seat “lip”

while holding the front column hand-

grip as shown in Fig. 5.

Lexis Light – ET1B User’s Manual T. Rev. 0512 PM 8

Front Column Adjustment (Figure 6)

To adjust the angle of the front

column, pull the column lock trigger

upward. Move the column into the

desired position and release. Push

lightly back and forth on the column to

ensure that it is locked in the desired

position.

1. For driving the Lexis Light

adjust column to the rear-most

position.

2. For getting in and out of the Lexis

Light seat comfortably, the

column may be moved away from

the seat to the entry/exit position

3. For detaching the front column

from the rear frame, adjust the

column fully forward to the detach

position (Fig. 6/3); remove battery

before adjusting the column to the

detach position.

CAUTION: When getting in and out of the Lexis Light seat, step only

on CENTER of foot platform. DO NOT STEP ON SIDE OF

FOOTPLATFORM to avoid tipping the Lexis Light.

NOTE: The rear frame, when folded, can be lifted by the handles (Fig 4/4).