Tysso PPD-1000 User Manual
User Manual
PPD-1000
Full Flat Touch Screen LCD Monitor
Version 1.3
© Copyright Fametech Inc. (TYSSO), 2017
ii
i
General Information
ABOUT THIS MANUAL
The purpose of this user’s manual is to provide general information on TYSSO PPD Series
POS monitor and to show the users how to configure the hardware-related configurations.
The information in this manual is subject to change without notice due to rapid improvement on
IT technology.
The users can get the most up to date information from our web site:
HUhttp://www.fametech.com.twU
WARNING
The terminal has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interface in a residential installation. This equipment can generate
and radiate radio frequency energy and, if not installed and used according to the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interface will not occur under particular installation. If this equipment does cause harmful
interference to radio or television reception, which is found by turning the equipment off and on,
the user is encouraged to try to correct the interface by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment or device
Connect the equipment to an outlet other than the receiver’s
Consult a dealer or an experienced radio/TV technician for assistance
WARRANTY LIMITS
If the PPD series machine is disassembled by any person other than the authorized
technicians, the warranty will be terminated. The users should consult his/her dealer for any
technical problems. Warranty does not cover any damage caused by improper use.
ii
TRADE MARKS AND SERVICE MARKS
TYSSO is a registered trademark of FAMETECH INC.
Other brand and product names are trademarks and registered trademarks and service marks
of their respective owners.
IMPORTANT SAFETY INFORMATION
Read all these instructions carefully.
Use only parts, especially power adapter, recommended by the manufacturer; unapproved
parts may be hazardous.
Before plugging the power cord into the AC inlet of the power supply unit, make sure that
the voltage applied to the power outlet is within the specified range (100V ~240V).
Improper power source voltage range will cause damage to the power supply unit.
Power off the PPD and remove the power adapter while cleaning the monitor.
Keep the PPDs away from water, direct sunlight, a heating or a radiator.
Do not place the PPD on an unstable cart, stand or table. If the machine falls, it may injure
people or cause serious damage to the appliance.
The PPD is equipped with a three-wire grounded plug with a third (grounding) pin. This is a
safety feature. If your outlet does not accommodate the three-wire plug, have an electrician
install a correct outlet, or use an adapter to ground the appliance safely. Do not leave out
the safety purpose of the grounded plug.
Do not allow anything to rest on the power cord. Do not locate the system where people
may walk on the cord.
Do not make the power outlet and extension cords overload. Overload can result in fire or
electric shock.
Do not push any object into the monitor cabinet. Dangerous voltage points may be touched
and the parts may be shorted out resulting in fire or electric shock.
Do not attempt to service the PPD on your own. Opening or removing cover can expose
you to dangerous voltage or other hazards.
Power off the monitor before installing or removing non-PNP (plug and play) devices.
If any of the following situations occurs, unplug the PPD from the power outlet immediately
and consult with a qualified service person:
1. The power cord or plug is damaged or frayed.
2. Liquid is spilled into the PPD.
3. The PPDs are dropped or the cabinet is damaged.
When the PPD is not in use, cover the PPD and store it with care.
1
Contents
General Information .................................................................................................... i
ABOUT THIS MANUAL .......................................................................................... i
WARNING .............................................................................................................. i
WARRANTY LIMITS .............................................................................................. i
TRADE MARKS AND SERVICE MARKS ............................................................... ii
IMPORTANT SAFETY INFORMATION .................................................................. ii
1. Introduction ......................................................................................................... 3
1.1 Unpacking.................................................................................................... 3
1.2 Product Overview ................................................................ ........................ 4
1.3 I/O Ports and Connectors ............................................................................ 7
1.4 Specifications .............................................................................................. 8
2. Install Your Monitor ............................................................................................. 9
3. Monitor Setting .................................................................................................. 10
3.1 OSD Control Panel .................................................................................... 10
3.2 On-Screen Display ..................................................................................... 11
4. Install the Touch Screen Driver ........................................................................ 12
4.1 Resistive Type Touch Panel ....................................................................... 13
4.1.1 Install the Driver of Resistive Type Touch Panel ............................. 13
4.1.2 Touch Screen Calibration (Resistive Type) ..................................... 18
4.2 Projective Capacitive Type Touch Panel .................................................... 21
4.2.1 Install the Driver of Projective Capacitive Type Touch Panel .......... 21
4.2.2 Touch Screen Utility ........................................................................ 24
Appendix: Install the MSR Module (Optional) ........................................................ 27
2
3
1. Introduction
The PPD-1000 is a compact and full-flat touch screen monitor that comes with a die-casting
metal back cover. Multiple interfaces with the compact base design enable desirable
connectivity and easy to use.
Within the 15-incn full-flat and high brightness vivid LCD panel, PPD-1000 supports 5-Wire
Resistive or Projective Capacitive Touch technology to ensure every touch can respond
immediately to the command without any loss.
1.1 Unpacking
The contents may vary with different options. If there’s any physical damage or missing parts,
please contact your supplier immediately. Please keep all packing materials in case you need
to ship back the device for service.
Monitor: 15” (Internal Speakers, 2W x 1)
Base Stand (with cable-routing hooks)
VGA Cable
AC Power Cord (US, EU or UK selectable)
Power Adaptor
USB Touch Cable (available for touch screen type only)
4
Power LED
1.2 Product Overview
Dimensions
Front View
5
OSD Control Panel
USB Port
COM Port
(Reserved for Customized
MSR Module)
Rear View
Side View
Note:
The Side USB/COM Port is reserved for customized MSR module installation.
Please consult the technical personnel before installation
6
Power Switch
Bottom View
Loading...