TYROLIT Hydrostress FSG513P Operating Manual

1099758

8 en / 31.08.2016

Operating Manual
Spare Parts List

—————————————————————————

Floor Saw FSG513P

Index / Indice 004

2

Manufacturer's address:
TYROLIT Hydrostress AG

Witzbergstrasse 18
CH-8330 Pfäffikon
Switzerland
Tel. [phone]
Fax [phone]

www.tyrolit.com

TYROLIT Hydrostress AG reserves the right to make technical changes without prior notice.

Copyright © 2005 TYROLIT Hydrostress AG, CH-8330 Pfäffikon ZH, Switzerland
All rights reserved, in particular copyrighting and translating rights.
Printing of this operating manual, including extracts from it, is prohibited. No parts of it may be
reproduced in any form or processed using electronic systems, duplicated or disseminated without the
written permission of TYROLIT Hydrostress AG.

3

Preface to the operating manual

This operating manual makes it easier to become familiar with the machine and to use it properly.

The operating manual contains important information on how to operate the machine safely, properly
and efficiently. Following the operating manual helps avoid danger, reduce repair costs and downtime,
and increase the machine's reliability and life.

The operating manual must be supplemented with instructions based on national regulations for
accident prevention and environmental protection.

The operating manual must always be readily available at the location where the machine is used.

The operating manual must be read and used by any person assigned tasks with the machine, such
as:

• operation, including set-up, repair of malfunctions during operation, disposal of production waste,
maintenance, disposal of materials

• maintenance (service, inspection, or repair) and/or

• transport

In addition to the operating manual and the regulations for accident prevention in force in the country
and at the location where the machine is used, recognized technical rules for safe and correct
operation must be followed.

Table of contents

1. Basic safety instructions

2. Machine description

3. Placement in operation

4. Transport

5. Operation

6. Maintenance

7. Repair of malfunctions

8. Warranty

4

1. Basic safety instructions

1.1 Warning and symbols in the manual

Danger! Points out that serious or even fatal injuries may result if not followed.
Caution! Points out that injuries may result if not followed.
Notice! Points out that damage to the machine or other equipment may result if not

followed.

1.2 Principle of intended use

1.2.1 The machine has been constructed using the latest technology and in accordance with

recognized safety guidelines. Nevertheless, the use of the machine may still represent a
risk of injury or death to the user or third parties, or damage to the machine and other
material.

1.2.2 The machine may only be used when it is in correct working order and for its intended

purpose. The operator must follow the instructions in the operating manual and be fully
aware of the safety requirements and hazards posed by the machine! In particular, any
faults that may compromise the safety of the machine must be repaired immediately.

1.2.3 The Floor Saw is intended solely for cutting joints in concrete or asphalt. Cutting of wood,

plastic or metal (except reinforcements in concrete) is prohibited!

Any additional or other use is considered improper. The manufacturer/supplier is not liable

for damages resulting from improper use.

Compliance with the operating manual and observation of inspection and service

requirements are essential components of proper use.

1.3 Organizational measures

1.3.1 Always keep the operating manual readily available at the location where the machine is

used!

1.3.2 In addition to the operating manual, observe and instruct the user in all generally applicable

legal and other mandatory regulations on accident prevention and environmental protection!

1.3.3 Personal assigned to work on the machine must have read the operating instructions and, in

particular, the chapter on safety before beginning work. Read the manual for the first time
when already working on the machine is too late. This applies especially to persons who
work on the machine only occasionally, such as those performing set-up and maintenance.

1.3.4 Check at least from time to time whether personnel are performing the work in compliance

with the operating manual and paying attention to risks and safety factors!

1.3.5 Use personal protective equipment where necessary or if required by regulations!

1.3.6 Obey all safety and danger notices on the machine!

1.3.7 Ensure that all safety and danger notices on the machine remain clearly legible!

5

1.3.8 In the event of safety-relevant changes to the machine or its operating performance, stop

the machine immediately and report the malfunction to the responsible authority/ person!

1.3.9 Do not make any modifications to the machine, add attachments, or reconfigure it without

the supplier’s permission!

1.3.10 Only use manufacturer’s original parts!

1.3.11 Observe the stipulated periods or the periods given in the operating manual for inspections!

1.3.12 Equipment and tools appropriate to the work are absolutely essential for performing

maintenance work.

1.4 Personnel selection and qualification;

1.4.1 Only reliable personnel may work with the machine.

Observe the minimum legal age.

1.4.2 Use only trained or instructed staff. Clearly establish individual responsibilities for operation,

set-up, maintenance and repair!

1.4.3 Ensure that only assigned personnel work with the machine!

1.4.4 Specify machine operator responsibilities – including those pertaining to road traffic

regulations – and authorize the operator to ignore any instructions from third parties that
may compromise safety!

1.4.5 Personnel who are being trained or instructed on the machine or are in a general training

program may only be permitted to work on the machine while under the constant
supervision of an experienced person!

1.4.6 Work on electrical equipment on the machine may only be carried out by an electrician or by

instructed persons under the guidance and supervision of an electrician in accordance with
electrical regulations.