Tyco Safety Canada 173G9080 Users manual

Connected Services Gateway Cellular Module

installation guide

Introduction This guide describes how to install the optional Connected Services Gateway Cellular Module,

antenna and antenna extensions.

There are two cellular modules available that connect to different cellular networks, AT&T 3G and Verizon LTE. The AT&T 3G cellular module requires one antenna. The Verizon LTE module requires two antennae.

In cases with poor signal strength at the Fire Alarm Control Unit (FACU), you may need to move the antenna to another location with improved network coverage using an extension kit.

Cautions, warnings, and regulatory information

READ AND SAVE THESE INSTRUCTIONS - Follow the instructions in this installation manual.

These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depend upon proper installation.

DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED - Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex product supplier.

ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be performed by a representative or authorized agent of your local Simplex product supplier.

STATIC HAZARD - Static electricity can damage components. Handle as follows:

FCC MODIFICATION STATEMENT

Digital Security Controls has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Digital Security Controls n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.

ISED CANADA INTERFERENCE STATEMENT

This device complies with Part 15 of the FCC Rules and ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, ême si le brouillage est susceptible d'en compromettre le fonctionnement.

FCC CLASS B DIGITAL DEVICE NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or experienced radio/television technician for help.

• Ground yourself before opening or installing components.

• Prior to installation, keep components wrapped in anti-static material at all times.

CAN ICES-3 (B) / NMB-3 (B)

Connected Services Gateway Cellular Module installation guide

Cautions, warnings, and regulatory information, continued

FCC/ISED CANADA WIRELESS NOTICE

This equipment complies with FCC and ISED Canada radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 m between the radiator and your body. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except as described in this user manual.

Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement on contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps. L'antenne (s) utilisée pour cet émetteur ne doit pas être situé ou opérant en conjonction avec une autre antenne ou émetteur, sauf tel que décrit dans ce mode d'emploi.

Antenna gain must be below/Gain de l'antenne doit être ci-dessous:

Carrier Frequency band 4100-6401, 4010-6401,

4007-6401

AT&T / Rogers

DSC M/N: 3G9080 with FCC ID: F53173G9080 IC: 160A-3G9080

GSM850 (B5) / FDD V PCS 1900 (B5) / FDD II

3.64 dBi

2.51dBi

Carrier Frequency band 4100-6400, 4010-6400,

4007-6400

Verizon

DSC M/N: LT9080 with FCC ID: F5317LT9080 IC: 160A-LT9080

WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20cm or more must be maintained between the antenna of this device and persons during device operation.

700 (B13) TBD AWS1700 (B4) TBD

+ 7 hidden pages

Tyco Safety Canada 173G9080 Users manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Cautions, warnings, and regulatory information