Tyco Safety Canada 09PC9155 User Manual
N11427
9032
PC9155 Wireless Alarm System
User Manual
WARNING: This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer. The entire manual
should be carefully read.
FCC COMPLIANCE STATEMENT
Telephone
Computer
Telephone
Telephone
Fax Machine
Alarm Dialing
Equipment
RJ-31X
Jack
Unused
RJ-11 Jack
Telephone
Line
Network
Service
Provider's
Facilities
Customer Premises Equipment and Wiring
Unused
RJ-11 Jack
Network
Demarcation
Point
Answering
System
CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limi ts for a Cla ss
B digital device, pursuant to Part 15 of the FCC Rules. Thes e limits are desig ned
to provide reasonable protection against harmful interfer-ence in a r esidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular ins tallation. If t his equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the us er is encourage d to tr y to cor rect the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and rece iver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult a dealer or experienced radio/television tec hnic ian for help.
The user may find the following booklet prepared by the FCC useful: ’How to
Identify and Resolve Radio/Television Interference Problems’. This booklet is
available from the U.S. Government Printing Office, Washington D.C. 20402,
Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rule s and, i f the product was
approved July 23, 2001 or later, the requir ements adopted by the ACTA. On the
top side of this equipment is a label that contains, among other information, a
product identifier. If requested, this number must be provided to the Telephone
Company.
Product Identifier: US:F53AL01B9155
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to th e premis es wiri ng and t elephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed t o b e co nnect ed to a compatible modular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may result in the devices
not ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local
Telephone Company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:
AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separate ly
shown on the label. REN = 0.1B
Incidence of Harm
If this equipment (PC9155-433) causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice is not practical, the Telephone
Company will notify the customer as soon as possible. Also, you will be advised
of your right to file a complaint with the FCC if you believe it i s ne cess ary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipme nt. If th is hap-
New Zealand - The following is a list of warnings applicable when this equipment is connected to the New Zealand Telecom Network.
General Warning
The grant of a Telepermit for any item of terminal equipment i ndicates only that Telecom has accept ed that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor
does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects
with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
Reverse Numbering (decadic signalling)
Decadic signalling should not be used as it is being progressively phased out of the network. DTMF dialling is 100%
available and it should always be used.
Line Grabbing Equipment
This equipment is set up to carry out test calls at pre-determined times. Such test calls will interrupt any other calls that
may be set up on the line at the same time. The timing set for such test calls should be discussed with the installer.
The timing set for test calls from this equipment may be subject to 'drift'. If this proves to be inconvenient and your calls
are interrupted, then the problem of timing should be discussed with the equipment installer. The matter should NOT be
reported as a fault to Telecom Faults Service.
D.C. Line Feed to Other Devices
During dialling, this device unit does not provide DC voltage to the series port connection and this may cause loss of
memory functions for the terminal devices (local telephone) connected to T-1, R-1.
General Operation (ringer sensitivity and loading)
This device only responds to Distinctive Alert cadences DA1 and DA2.
pens the Telephone Company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted s erv ice .
Equipment Maintenance Facility
If trouble is experienced with this equipment (PC9155/WT5500) for repair or
warranty information, contact the facility indicated below. If the equipment is
causing harm to the telephone network, the Telephone Company may request
that you disconnect the equipment until the problem is solved. This equipment
is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state t ariffs. Contact the stat e public
utility commission, public service commission or corporation commission for
information.
Alarm dialling equipment must be able to seize the telephone line and place a
call in an emergency situation. It must be able to do this even if othe r equipment
(telephone, answering system, computer modem, etc.) already has the tele phone
line in use. To do so, alarm dialling equipment must be connected to a properly
installed RJ-31X jack that is electrically in series with and ahead of all other
equipment attached to the same telephone line. Proper ins tallatio n is depi cted in
the figure below. If you have any questions concerning these instructions, you
should consult your telephone company or a qualified installer about installing
the RJ-31X jack and alarm dialling equipment for you.
INDUSTRY CANADA STATEMENT
NOTICE: This product meets the applicable Industry Canada technical specifications.
Le présent materiel est conforme aux specifications techniques applicables d’Industrie Canada.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1 .
L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.
The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.
L’indice d’équivalence de la sonnerie
(IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés
à une interface téléphonique. La termi naison d’une interface peut consister en
une combinaison quelconque de dispositifs, à la seule co ndition que la somme
d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
The term ’IC:’ before the radio certification number on ly signi fies th at Indust ry
Canada technical specifications were met.
Certification Number IC: 160A-PC9155
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Table of Contents
About Your Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Fire Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Controls & Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Arming & Disarming the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Stay Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Night Arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Silent Exit Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Quick Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Bell/Siren Sounds After Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Remote Arming and Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Emergency Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
When Alarm Sounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Intrusion (Burglar) Alarm Continuous Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Fire Alarm Pulsed Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Time & Date Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bypassing Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Trouble Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Alarm Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Door Chime (Entry/Exit Beeps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Access Code Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
User Code Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Zone Bypassing Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Bell Squawk Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Erasing an Access Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
User Function Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Changing Brightness/Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Changing the Buzzer Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Viewing the Event Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Late to Open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Proximity Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2-Way Wireless Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Keylock Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Testing Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Sounder and Display Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Walk Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Allowing Computer Access To Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
i
Reference Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
System Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Access Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Sensor / Zone Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Guidelines for Locating Smoke Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Household Fire Safety Audit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Fire Escape Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Always ensure you obtain the latest version of the User Guide. Updated versions of this
User Guide are available by contacting your distributor.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock and/or injury, observe the following:
• Do not spill any type of liquid on the equipment.
• Do not attempt to service this product yourself. Opening or removing the cover may
expose you to dangerous voltage or other risk. Refer servicing to qualified service personnel. Never open the device yourself.
• Do not touch the equipment and its connected cables during an electrical storm; there
may be a risk of electric shock from lightening.
• Do not use the Alarm System to report a gas leak if it is near the leak.
REGULAR MAINTENANCE AND TROUBLESHOOTING
Keep your Alarm Controller in optimum condition by following all the instructions that are
included within this manual and/or marked on the product.
CLEANING
• Clean the enclosure (case) by wiping with a damp cloth only.
• Do not use abrasives, thinners, solvents or aerosol cleaners (spray polish) that may enter
through holes in the enclosure (case) of the Alarm Controller and cause damage.
• Do not use any water or any other liquid.
• Do not wipe the front cover with alcohol.
TROUBLESHOOTING
Occasionally, you may have a problem with your Alarm Controller or telephone line. If this
happens, your Alarm Controller usually identifies the problem and displays an error message. Refer to the provided list when you see an error message on the display. If additional
help is required, contact your distributor for service.
WAR NING: This equipment, PC9155 Alarm System shall be installed and used within an
environment that provides the pollution degree max 2 and over-voltages category II nonhazardous locations, indoor only. It is designed to be installed, serviced and/or repaired by
service persons only; [service person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be
exposed in performing a task and of measures to minimize the risks to that person or other
persons]. For EU and Australian Markets, the equipment is permanently connected; an
accessible disconnect device shall be incorporated in the building installation wiring. For
North America it is a direct plug-in connection; the socket outlet shall be installed near the
PC9155 and shall be easily accessible. The plug of the direct plug-in transformer serves as
the disconnect device.
NOTE: There are no parts replaceable by the end-user within this equipment.
This publication covers the following models:
• PC9155-433
• PC9155D-433
• PC9155G-433
NOTE: 868 MHz models are not UL/ULC listed.
• PC9155-868 • WT5500-433 • WT5500P-868
• PC9155D-868 • WT5500P-433 • PT4
• PC9155G-868 • WT5500-868 • PT8
ii
About Your Security System
Read this manual carefully and have your installer instruct you on your system's operation and
on which features have been implemented in your system. All users of this system should be
equally instructed in its use. Fill out the ’System Information’ page with all of your zone information and access codes and store this manual in a safe place for future reference.
NOTE: Please consult your installer for further information regarding the false alarm reduction
features built into your system as all are not covered in this manual.
Fire Detection
This equipment is capable of monitoring fire detection devices such as smoke detectors and
providing a warning if a fire condition is detected. Good fire detection depends on having adequate number of detectors placed in appropriate locations. This equipment should be installed
in accordance with NFPA 72 (N.F.P.A., Battery march Park, Quince MA 02269). Carefully review
the Family Escape Planning guidelines in this manual.
NOTE: Your installer must enable fire detection before it becomes functional.
Te s ti ng
To ensure that your system continues to function as intended, you must test your system weekly.
Please refer to the ‘Testing your System’ section in this manual. If your system does not function
properly, call your installing company for service.
Monitoring
This system is capable of transmitting alarms, troubles & emergency information to a central station. If you initiate an alarm by mistake, immediately call the central station to prevent an unnecessary response.
NOTE: The monitoring function must be enabled by the installer before it becomes functional.
NOTE: This system has a communicator delay of 30 seconds. It can be removed, or it can be
increased up to 45 seconds by the installer.
NOTE: Ensure that your Installer verifies that your system is compatible with the Central Station
Receiver format at yearly intervals.
Maintenance
With normal use, the system requires minimum maintenance. Note the following points:
• Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened
cloth should remove normal accumulations of dust.
• The standby battery shall be replaced every 4-5 years by service persons only.
NOTE: Do not attempt to replace the battery or open the enclosure, there is a risk of electric
shock and/or fire.
• For other system devices such as smoke detectors, motion detectors, glassbreak detectors or
door/window contacts, consult the manufacturer’s literature for testing and maintenance
instructions if applicable.
General System Operation
Your security system includes an alarm control/keypad and various sensors and detectors. The
keypad is mounted by the main exit/entry location.
The security system has several zones of area protection. Each of these zones communicates to
a single wireless sensor (motion detectors, glassbreak detectors, door contacts, etc.) or to one
or more hard wired sensors. A sensor in alarm is indicated by messages on the LCD keypad.
Additional features include Automatic Inhibit (Swinger Shutdown) for Alarm; Tamper and Trouble
signals after 3 occurrences in a given set period; and a Programmable Keypad Lockout option.
For SIA CP-01 classified installations, the swinger shutdown feature is programmed such that
one or two trips will shut down the zone. The zone will be restored after a manual reset (by entering the access code at the time of disarming the alarm system) or it will be reset automatically
after 48 hours with no trips on any zones.
NOTE: Only the installer or service professional should have access to the system.
1
Keypad Controls & Indicators
1
23
4
5
6
7
8
0
#
9
*
Enter Code to
Arm System
<>
Stay
Function Keys
LED Indicators
Ready
Armed
Trouble
Power
Away
Chime
Bypass
Quick
Exit
Scroll Keys
Backlighting
Sensor
LCD
Prox Tag Detector
(if available)
Emergency Keys
Fire
Auxiliary
Panic
< > indicates user can
scroll through options
9033
A security system cannot prevent emergencies. It is only intended to alert you and – if included –
IMPORTANT NOTICE
your central station of an emergency situation. Security systems are generally very reliable but
they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance. Your security system should be installed and serviced by
qualified security professionals who should instruct you on the level of protection that has been
provided and on system operations.
Language Selection
Your system can display messages in different languages.
1. Press and hold both buttons simultaneously.
2. Using the buttons, scroll through the available languages.
3. Press to select your desired language.
Arming & Disarming the System
Stay Arming
Stay arming will bypass the interior protection (i.e. motion sensors) and arm the perimeter of the
system (i.e. doors and windows). Close all sensors (i.e. stop motion and close doors). The
Ready ( ) indicator should be on.
Press and hold the Stay button until it beeps (approx. 2 seconds) and/or enter your Access
Code and do not leave the premises. During the setting state (exit delay active), the Armed ( )
and Ready ( ) indicators will light.
When the exit delay is completed, the alarm system is armed/set and this is indicated on the
keypad as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on.
The Armed ( ) indicator and a bypass message will be displayed. The system will automatically bypass certain interior sensors (i.e. motion sensors).
NOTE: For SIA FAR listed panels, the Stay Arming Exit Delay will be twice as long as the Away
Arming Exit Delay.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction then the security system will arm in the Stay Armed mode if the exit delay time expires
and no exit has been made.
Night Arming
To fully arm the system when it has been armed in Stay Mode, press at the keypad. All
interior zones will now be armed except for devices programmed as Night Zones.
NOTE: Your installer can also program a function key on the keypad to allow you to arm the
system in Night Mode. This would allow Night Arming to be activated by holding down a function
key for 2 seconds.
Night zones are only armed in Away mode, this permits limited movement within the premises
when the system is fully armed. Ensure that your installer has provided you with a list identifying
zones programmed as night zones.
2
When the interior zones are activated (i.e., ) you must enter your access code to disarm
the system to gain access to interior areas that have not been programmed as night zones.
Silent Exit Delay
If the system is armed using the Stay button or using the ’No Entry’ Arming method (
[access code]), the audible progress annunciation (keypad buzzer) will be silenced and the exit
time will be doubled for that exit period only.
Away Arming
Close all sensors (i.e. stop motion and close doors). The Ready ( ) indicator should be on.
To arm, press and hold the Away Button for 2 seconds and/or enter your Access Code, or press
to Quick Arm.
During the setting state (exit delay active) the Armed ( ) and Ready ( ) indicators will turn on,
and the keypad will sound one beep per second. You now have ____ seconds to leave the premises (please check with your installer to have this time programmed). An audible annunciation,
whose pulsating rate is distinctly different, will sound during the last ten seconds of the exit delay
to warn person(s) that the exit delay is running out. To cancel the arming sequence, enter your
access code or present your prox tag.
When the exit delay is completed, the alarm system is armed and this is indicated on the keypad
as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on and the
keypad will stop sounding.
The system can also be armed/disarmed with a wireless key and with proximity tags. Refer to
the ‘Proximity Tags’ and ‘2-Way Wireless Key’ sections on page 9 for more details.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction then the violation, restoral followed by a second violation of the entry/exit zone before
the end of the exit delay will restart the exit delay.
Quick Exit
If the system is armed and you need to exit, use the Quick Exit function to avoid disarming and
rearming the system. Press and hold the Quick Exit button for 2 seconds or press . You
now have 2 minutes to leave the premises through your exit door. When the door is closed again,
the remaining exit time is cancelled.
Bell/Siren Sounds After Away Arming
Audible Exit Fault
In order to reduce false alar
ms, the Audible Exit Fault is designed to notify you of an improper
exit when arming the system. If you fail to securely close the Exit/Entry door during the programmed exit delay period, the system will sound the alarm to indicate an improper exit (your
installer will tell you if this feature has been enabled on your system). If this occurs:
1. Re-enter the premises.
2. Enter your access code, or present your prox tag, before the entry delay timer expires, to dis-
arm the system.
3. Follow the Away arming procedure again, ensure that the entry/exit door(s) are secured.
Arming Error
An error tone will sound if the system is unable to arm. This will happen if the system is not ready
to arm (i.e. sensors are open), or if an incorrect user code has been entered. If this happens,
ensure all sensors are secure, press and try again.
Disarming
Enter your access code to disarm the system when it is armed (Armed ( ) indicator is on). The
keypad will sound a continuous tone after the entry delay has been initiated by opening the
entry/exit door. Enter your code within _______ seconds to avoid an alarm condition (check with
your installer to have this time programmed).
Disarming Error
If your code is invalid, the system will not disarm and a 2-second error tone will sound. If this
happens, press and try again.
3
Loading...