Tyco Safety Canada 005501Z32433 User Manual

WARNING: Please refer to the System Installation Manual for

information on limitations regarding product use and function and
information on the limitations as to liability of the manufacturer.

Installation Manual

DLS-3 v1.3 or higher

LCD55O1Z32-433 NA

version 1.0

WARNING Please Read Carefully

Note to Installers

This warning contains vital information. As the only individual in
contact with system users, it is your responsibility to bring each item
in this warning to the attention of the users of this system.

System Failures

This system has been carefully designed to be as effective as pos­sible. There are circumstances, however, involving fire, burglary , or
other types of emergencies where it may not provide protection. Any
alarm system of any type may be compromised deliberately or may
fail to operate as expected for a variety of reasons. Some but not all
of these reasons may be:

■■

■ Inadequate Installation

■■

A security system must be installed properly in order to provide
adequate protection. Every installation should be evaluated by a se­curity professional to ensure that all access points and areas are cov­ered. Locks and latches on windows and doors must be secure and
operate as intended. Windows, doors, walls, ceilings and other build­ing materials must be of sufficient strength and construction to pro­vide the level of protection expected. A reevaluation must be done
during and after any construction activity. An evaluation by the fire
and/or police department is highly recommended if this service is
available.

■■

■ Criminal Knowledge

■■

This system contains security features which were known to be ef­fective at the time of manufacture. It is possible for persons with
criminal intent to develop techniques which reduce the effectiveness
of these features. It is important that a security system be reviewed
periodically to ensure that its features remain effective and that it be
updated or replaced if it is found that it does not provide the protec­tion expected.

■■

■ Access by Intruders

■■

Intruders may enter through an unprotected access point, circum­vent a sensing device, evade detection by moving through an area of
insufficient coverage, disconnect a warning device, or interfere with
or prevent the proper operation of the system.

■■

■ Power Failure

■■

Control units, intrusion detectors, smoke detectors and many other
security devices require an adequate power supply for proper opera­tion. If a device operates from batteries, it is possible for the batter­ies to fail. Even if the batteries have not failed, they must be charged,
in good condition and installed correctly. If a device operates only
by AC power, any interruption, however brief, will render that de­vice inoperative while it does not have power. Power interruptions
of any length are often accompanied by voltage fluctuations which
may damage electronic equipment such as a security system. After a
power interruption has occurred, immediately conduct a complete
system test to ensure that the system operates as intended.

■■

■ Failure of Replaceable Batteries

■■

This system’s wireless transmitters have been designed to provide
several years of battery life under normal conditions. The expected
battery life is a function of the device environment, usage and type.
Ambient conditions such as high humidity, high or low tempera­tures, or large temperature fluctuations may reduce the expected
battery life. While each transmitting device has a low battery moni­tor which identifies when the batteries need to be replaced, this moni­tor may fail to operate as expected. Regular testing and maintenance
will keep the system in good operating condition.

■■

■ Compromise of Radio Frequency

■■

(Wireless) Devices

Signals may not reach the receiver under all circumstances which
could include metal objects placed on or near the radio path or delib­erate jamming or other inadvertent radio signal interference.

■■

■ System Users

■■

A user may not be able to operate a panic or emergency switch pos­sibly due to permanent or temporary physical disability, inability to
reach the device in time, or unfamiliarity with the correct operation.
It is important that all system users be trained in the correct opera­tion of the alarm system and that they know how to respond when
the system indicates an alarm.

■■

■ Smoke Detectors

■■

Smoke detectors that are a part of this system may not properly alert
occupants of a fire for a number of reasons, some of which follow.
The smoke detectors may have been improperly installed or posi­tioned. Smoke may not be able to reach the smoke detectors, such as
when the fire is in a chimney, walls or roofs, or on the other side of
closed doors. Smoke detectors may not detect smoke from fires on
another level of the residence or building.

Every fire is different in the amount of smoke produced and the rate
of burning. Smoke detectors cannot sense all types of fires equally
well. Smoke detectors may not provide timely warning of fires
caused by carelessness or safety hazards such as smoking in bed,
violent explosions, escaping gas, improper storage of flammable
materials, overloaded electrical circuits, children playing with
matches or arson.
Even if the smoke detector operates as intended, there may be cir­cumstances when there is insufficient warning to allow all occu­pants to escape in time to avoid injury or death.

■■

■ Motion Detectors

■■

Motion detectors can only detect motion within the designated ar­eas as shown in their respective installation instructions. They can­not discriminate between intruders and intended occupants. Motion
detectors do not provide volumetric area protection. They have mul­tiple beams of detection and motion can only be detected in unob­structed areas covered by these beams. They cannot detect motion
which occurs behind walls, ceilings, floor, closed doors, glass parti­tions, glass doors or windows. Any type of tampering whether in­tentional or unintentional such as masking, painting, or spraying of
any material on the lenses, mirrors, windows or any other part of the
detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in
temperature. However their effectiveness can be reduced when the
ambient temperature rises near or above body temperature or if there
are intentional or unintentional sources of heat in or near the detec­tion area. Some of these heat sources could be heaters, radiators,
stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so
on.

■■

■ Warning Devices

■■

Warning devices such as sirens, bells, horns, or strobes may not
warn people or waken someone sleeping if there is an intervening
wall or door. If warning devices are located on a different level of
the residence or premise, then it is less likely that the occupants will
be alerted or awakened. Audible warning devices may be inter­fered with by other noise sources such as stereos, radios, televi­sions, air conditioners or other appliances, or passing traffic. Au­dible warning devices, however loud, may not be heard by a hear­ing-impaired person.

■■

■ Telephone Lines

■■

If telephone lines are used to transmit alarms, they may be out of
service or busy for certain periods of time. Also an intruder may cut
the telephone line or defeat its operation by more sophisticated means
which may be difficult to detect.

■■

■ Insufficient Time

■■

There may be circumstances when the system will operate as in­tended, yet the occupants will not be protected from the emergency
due to their inability to respond to the warnings in a timely manner.
If the system is monitored, the response may not occur in time to
protect the occupants or their belongings.

■■

■ Component Failure

■■

Although every effort has been made to make this system as reliable
as possible, the system may fail to function as intended due to the
failure of a component.

■■

■ Inadequate Testing

■■

Most problems that would prevent an alarm system from operating
as intended can be found by regular testing and maintenance. The
complete system should be tested weekly and immediately after a
break-in, an attempted break-in, a fire, a storm, an earthquake, an
accident, or any kind of construction activity inside or outside the
premises. The testing should include all sensing devices, keypads,
consoles, alarm indicating devices and any other operational de­vices that are part of the system.

■■

■ Security and Insurance

■■

Regardless of its capabilities, an alarm system is not a substitute for
property or life insurance. An alarm system also is not a substitute
for property owners, renters, or other occupants to act prudently to
prevent or minimize the harmful effects of an emergency situation.

Table of Contents

T A B L E O F C O N T E N T S

Introduction 1

Section 1: Installation 2

1.1 Unpacking ................................................................................................................. 2

1.2 Mounting.................................................................................................................... 2

1.3 Wiring .......................................................................................................................... 2

1.4 Applying Power ........................................................................................................ 3

1.5 Enrolling the Keypad................................................................................................ 3

Section 2: Keypad Programming 5

2.1 Programming the Keypad ...................................................................................... 5

2.2 Function Key Options ............................................................................................... 5

2.3 Clock Options ........................................................................................................... 5

2.4 Alarms Displayed While Armed Option ................................................................ 6

2.5 Emergency (Fire, Auxiliary, Panic) Key Options .................................................. 6

2.6 Door Chime Options ................................................................................................ 6

Section 3: Receiver Programming 8
Enroll & Program Devices 8

3.1 Electronic Serial Numbers ....................................................................................... 8

3.2 Enroll Wireless Devices Using Zones ....................................................................... 8

3.3 Enroll & Program Wireless Keys ............................................................................... 9

3.4 Identified Wireless Keys.......................................................................................... 10

3.5 Enrolling & Programming Handheld Keypads ................................................... 11

Section 4: Other Programming 12

4.1 Program Zones and Partitions .............................................................................. 12

4.2 Enable Receiver Supervision ................................................................................ 12

4.3 Enable Supervision of Wireless Zones .................................................................. 12

4.4 RF Jam Detect Zone .............................................................................................. 13

4.5 Receiver Software Default .................................................................................... 13

Section 5: Testing & Mounting 15

5.1 Test the placement of WLS904, WLS904P, WLS906,

WLS907, WLS912, WLS914 and WLS925L devices ............................................... 15

5.2 Test WLS909 and WLS929 Reception ................................................................... 16

Section 6: Additional Notes 17

6.1 Trouble Conditions ................................................................................................. 17

6.2 Replacing Batteries in Wireless Devices ............................................................. 17

Section 7: Troubleshooting 18

Section 8: Programming Worksheets 19

Appendix A: Guidelines for Locating Smoke Detectors 26

Introduction

I N T R O D U C T I O N

Introduction

The LCD5501Z32-433 keypad combines a standard PC5132 receiver with an
LCD5501Z keypad that presents system status using an LCD-style display with
fixed messages. With the addition of the keypad, the control panel will now
support up to 32 zones. The LCD5501Z32-433 is compatible with the following
DSC security systems:

• PC5010 (all versions) • PC1555 v2.3 and higher

• PC5015 (all versions) • Power608 v2.3 and higher

• PC580 v2.3 and higher • PC5008 v2.3 and higher

NOTE: Control panels previous to version 2.3 support 8 wireless zones.
NOTE: Only one LCD5501Z32 keypad can be connected per system. If more k eypads

are required please select other DSC compatible keypads f or the system being installed.

Specifications and Features

• Maximum Current Draw: 260mA (with back lighting boost on)

• Frequency: 433.92 mHz

• Zones - receiver can receive signals from up to 32 wireless zones

• Supervisory - programmable supervisory window, one to 24 hours

• Location

- can be wired up to 1000 ft. / 305 m from the main panel with 22 gauge wire

- for longer wire runs, thicker gauge wire must be used.

• Compatibility: The LCD5501Z32-433 can be connected to the following panels:
PC5010, PC5015, PC5008, PC1555, PC580

• Connects to control panel via 4-wire Keybus

• One keypad zone input

• Optional tamper version

• Five programmable function keys

• Ready (green), Armed (red) and Trouble (yellow) status lights

1

Installation

S E C T I O N 1

1.1 Unpacking

The LCD5501Z32-433 package includes the following parThe LCD5501Z32-433 package includes the following par

The LCD5501Z32-433 package includes the following par

The LCD5501Z32-433 package includes the following parThe LCD5501Z32-433 package includes the following par

• One LCD5501Z32-433 keypad

• One 5.6K Ohm resistor

• Four mounting screws

• One keypad inner door label

• One set of Fire, Auxiliary and Panic key labels

• One LCD5501Z User Sheet

• One LCD5501Z32-433 Installation Manual

1.2 Mounting

You should mount the keypad where it is accessible to designated points of
entry and exit. Once you have selected a dry and secure location, perform the
following steps to mount the keypad:

1. Remove the keypad backplate by loosening the screw located at the base of
the unit.

2. Secure the keypad backplate to the wall in the desired location. Use the
screws provided.

3. Before attaching the keypad to its backplate, complete the keypad wiring as
described in the next section.

1.3 Wiring

1. Before beginning to wire the unit, ensure that all power (AC transformer and
battery) is disconnected from the control panel.

2. Connect the four Keybus wires from the control panel (red, black, yellow and
green) to the keypad terminals (R B Y G). Consult the diagram below:

ts:ts:

ts:

ts:ts:

3. You can connect a device, such as a door contact, to the “Z” terminal of the
LCD5501Z32-433. This eliminates the need to run wires back to the control panel
for the device. T o connect the zone, run one wir e from the device to the Z terminal
and the other wire from the device to the B (black) terminal. For powered devices,
run the red wire to the R (positive) terminal and the black wire to the B (negative)
terminal. When using end of line supervision, connect the zone according to one
of the configurations outlined in your system’s

2

Installation Manual

.

I N S T A L L A T I O N

1.4 Applying Power

Once all wiring is complete, apply power to the control panel:

1. Connect the battery leads to the battery.

2. Connect the AC transformer.

For more information on control panel power specifications, see the control

Installation Manual

panel

.

NOTE: Do not connect the power until all wiring is complete.

1.5 Enrolling the Keypad

Once all wiring is complete, you will need to enter a 2-digit number that tells the
system the partition and slot assignment of the keypad.

If your system has partitions, you will also need to assign the keypad to a
partition (1st digit).

The slot assignment (2nd digit) tells the panel which keypad slots are occupied.
The panel can then generate a fault when a keypad supervisory signal is not
present. There are eight available slots for keypads. LCD5501Z32-433 keypads
are always assigned to slot 1 by default. You will need to assign each keypad to
its own slot (1 to 8).

NOTE: The LCD5501Z32-433 enrolls as two modules:

1 = keypad section of the LCD5501Z32-433

17 = receiver section of the LCD5501Z32-433

Enter the following at each keypad installed on the system:

1. Enter Installer Programming by pressing [*][8][Installer’s Code]

2. Press [000] for Keypad Programming

3. Press [0] for Partition and Slot Assignment

4. Enter a two digit number to specify the partition and slot assignment.

NOTE: If your system does not have partitions, enter [1] for the first digit.

1st digit Enter 0 for Global Keypad

Enter 1 for Partition 1 Keypad
Enter 2 for Partition 2 Keypad

2nd digit Enter 1 to 8 for Slot Assignment

5. Press the [#] key twice to exit programming.

6. After assigning all keypads, perform a supervisory reset by entering
[*][8][Installer’s Code][902]. The panel will now supervise all assigned keypads
and enrolled modules on the system.

To review which modules the control panel is currently supervising:

1. Enter [✱][8][Installer’s Code]

11

11

2. Enter [903] to display all modules. On the
scroll on the keypad to indicate that the
11

1 designates the keypad section, and

11
is also supervised. If using an LCD5501Z keypad, scroll until the module name
appears on the display.

3. To exit press [#].

LCD5501Z32-433 keypad,

LCD5501Z32-433 is present on the system.

1717

17 is used to show the receiver section

1717

3

1 and

11

1

11

77

7 will

77

I N S T A L L A T I O N

If both modules do not show on the keypad, one of the following conditions may
be present:

•the keypad is not connected properly to the Keybus

•there is a problem with the Keybus wiring run

•the keypad does not have enough power

1.6 Downloading

This product has an integrated PC5132-433 v4.1 receiver. When downloading to
this keypad, please select the PC5132-433 v4.1 file. DLS-3 v1.3 and greater must
be used in order to have the capability of downloading to this keypad.

4

Keypad Programming

S E C T I O N 2

2.1 Programming the Keypad

There are several programming options available for the LCD5501Z32-433
keypad. These are described below. Record all your programming choices in
the programming worksheets included in this manual.

Programming the LCD5501Z32-433 is similar to programming the rest of the
system. When you are in the LCD5501Z32-433 programming sections, the keypad
will display which options are turned on along the top of the display. To turn an
option on or off, press the number corresponding to the option on the number pad.
The numbers of the options that are currently turned ON will be displayed.

For example, if options 1 and 2 are on, the display will look like this:

For information on programming the rest of your security system, please refer to
your system’s

2.2 Function Key Options

The function keys are programmed in sections [1] to [5]. By default, the 5 function
keys on the keypad are programmed as Stay Arm (03), Away Arm (04), Chime
(06), Sensor Reset (14) and Quick Exit (16). You can change the function of each
key on every keypad. Please see your system’s
tions on programming the keys, and a complete list of all the function key options
available for your system.

Installation Manual

.

Installation Manual

for instruc-

2.3 Clock Options

The LCD5501Z32-433 will display the current time after 30 seconds of no key
presses. To set the correct time and date for the system, please refer to your
system’s
with the following options. To change the clock options:

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. Enter section [6] to go to clock options.

4. To turn any of the options on or off, press [1], [2], or [3]:

NOTE: If the Time does not display on keypad option is selected, make sure that
the Keypad displays time when zones are open option is also selected.

Instruction Manual

[1] ON = Time displays on keypad

OFF = Time does not display on keypad

[2] ON = Clock display is in AM/PM format

(e.g. 08:00 AM)

OFF = Clock display is in 24-hour format (e.g. 20:00)

. You can change how the keypad displays the time

5

K E Y P A D P R O G R A M M I N G

[3] ON = Keypad does not display time when zones are open

OFF = Keypad displays time when zones are open

5. When you are finished programming the clock options, press [#] to exit.

2.4 Alarms Displayed While Armed Option

You can disable the display of alarms on the keypad when the system is armed.
The display of alarms is enabled by default. To disable the display of alarms
when the system is armed, turn off section [6], option [5]:

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. To turn the display of alarms on or off, enter section [6].

4. Turn option [5] on or off:
[5] ON = Alarms not displayed while system is armed

OFF = Alarms are always displayed while system is armed

5. When you are finished, press [#] to exit.

2.5 Emergency (Fire, Auxiliary, Panic) Key Options

You can enable or disable the Fire, Auxiliary and Panic keys at each keypad.
These keys are enabled by default. Please see your system’s

Manual

for more information on these keys and their options. To turn any of the

emergency keys on or off on the keypad:

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. Enter section [7].

4. To turn the emergency key options on or off, press [1], [2], or [3]:
[1] ON = Fire key enabled

OFF = Fire key disabled

[2] ON = Auxiliary key enabled

OFF = Auxiliary key disabled

[3] ON = Panic key enabled

OFF = Panic key disabled

5. When you are finished, press [#] to exit.

Installation

2.6 Door Chime Options

You can program the LCD5501Z32-433 keypad to sound a tone when any
zone is opened or closed. There are two parts to the LCD5501Z32-433 door
chime programming:

• Program if the LCD5501Z32-433 will chime when zones are opened and/or closed.

• Program the type of sound the LCD5501Z32-433 will make when an individual
zone is opened or closed.

For the door chime feature to work, you will also need to turn on the Door Chime
attribute for each zone that will trigger the chime. This programming is done in
the control panel software. Refer to your control panel’s
more information.

Installation Manual

for

6

K E Y P A D P R O G R A M M I N G

Door Chime on Zone Openings/Closings

You can program each LCD5501Z32-433 keypad to sound a door chime when zones
are opened and/or when they are closed. By default, LCD5501Z32-433 keypads are
programmed to sound door chimes on both zone openings and closings.

To change the door chime opening/closing settings, at each LCD5501Z32-433
keypad:

1. Enter [*][8][Installer’s code]

2. Enter [000] to go to keypad programming

3. Enter section [6].

4. To turn the options on or off, press [6] or [7]:
[6] ON = Door Chime Enabled for Zone Openings

OFF = Door Chime Disabled for Zone Openings

[7] ON = Door Chime Enabled for Zone Closings

OFF = Door Chime Disabled for Zone Closings

5. When you are finished, press [#] to exit.

Door Chime Sounds

You can program the LCD5501Z32-433 keypad to make different door chime
sounds for individual zones, or groups of zones. Each LCD5501Z32-433
keypad can make any of four door chime sounds for each zone that triggers the
door chime:

· 4 quick beeps (default sound)

· ‘Bing – Bing’ tone

· ‘Ding – Dong’ tone

· ‘Alarm’ tone

NOTE: F or a zone to be able to trigger the door chime sound, the Door Chime z one
attribute must also be enabled in the control panel programming. Please see your
control panel Installation Manual.

To change the door chime sounds:

1. Enter [*][8][Installer’s code].

2. Enter [*] to go to door chime sound programming.

3. Enter a 2-digit number for the zone you want to program [01] - [32].

4. Turn one of the following options on by pressing [1], [2], [3], or [4]:
[1] 4 quick beeps (default sound)
[2] ‘Bing – Bing’ tone
[3] ‘Ding – Dong’ tone
[4] ‘Alarm’ tone

NOTE: Make sure that only one of the above options is turned on. If more than one is
on, the keypad will sound the first option that is enabled. If none of the options are
selected, the keypad will not make any sound when the zone is opened or closed.

5. To program the door chime sound for another zone, repeat steps 3 and 4.

6. When you are finished programming the door chime sounds, press [#] to exit.

7