TYCO-ELECTRONICS RD SOCKET 10P Datasheet

MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Table of Contents
Introduction
This catalog has been designed to assist you, our customer, iden­tify products to satisfy your con­nector needs for printed circuit board headers, mass termination connectors preloaded with con­tacts, crimp-snap contacts and housings, and card edge con­nectors with preloaded contacts.
The list at right identifies by centerline the types of product available and is meant to be of assistance to you in the product selection process.
Introduction and Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 3
Connector Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
.050 [1.27] Centerline Connectors
MTA-50 IDC Connectors and Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
Introduction and Wire-to-Board Mateability Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
IDC Connector Kits (Feed-Thru and Closed End)
Ribbon Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5, 6
Discrete Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 8
Through-Hole Header Assemblies
Vertical and Right-Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Surface Mount Header Assemblies
Vertical and Right-Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
.100 [2.54] Centerline Connectors
MTA-100 IDC Connectors and Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-31
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Wire-to-Board Mateability Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12, 13
Connectors — UL94V-2 and UL94V-0
Closed End with and without Polarizing Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14, 15
Feed-Thru with and without Polarizing Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15
LED Closed End and Feed-Thru — UL94V-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14, 15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16, 17
Posted Connectors Mateability Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18, 19
IDC
MTA-50
MTA-100 Posted Connectors (Wire-to-Wire) UL94V-2
Closed End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Feed-Thru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Headers — UL94V-0
Flat — Straight and Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Narrow Flat — Straight and Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Polarized — Straight and Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Friction Lock — Straight and Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Headers with Retention Peg — Straight Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
IDC
MTA-100
High Profile Headers — Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Polarized — High Temperature, Straight and Right-Angle Posts . . . . . . . . . . . . . . . . .27
Friction Lock — High Temperature, Straight and Right-Angle Posts . . . . . . . . . . . . . .28
Polarized — Surface Mount, Straight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Friction Lock — Surface Mount, Straight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Shrouded — Straight and Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
CST-100 II Crimp Contacts, Housings and Shrouded Headers . . . . . . . . . . . . . . . . . . . . . . . . .31, 32
.156 [3.96] Centerline Connectors
MTA-156 IDC Connectors and Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33-57
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Crimp
CST-100 II
Wire-to-Board Mateability Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34, 35
Connectors — UL94V-2 and UL94V-0
Closed End with Locking Ramp, with and without Polarizing Tabs . . . . . . . . . . .36, 37
Closed End without Locking Ramp, with and without Polarizing Tabs . . . . . . . . .36, 37
Feed-Thru with Locking Ramp, with and without Polarizing Tabs . . . . . . . . . . . . .38, 39
Feed-Thru without Locking Ramp, with and without Polarizing Tabs . . . . . . . . . . .38, 39
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-42
Posted Connectors Mateability Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43, 44
MTA-156 Posted Connectors (Wire-to-Wire) — UL94V-2
Closed End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
IDC
MTA-156
© 1977, 1978, 1979, 1980, 1983, 1986, 1988, 1992, 1993, 1994, 1995, 1999, 2000, 2001, 2002, 2003 and 2005 by Tyco Electronics Corporation. All International Rights Reserved.
AMP, AMP-O-LECTRIC, AMP-O-MATIC, AMPOMATOR, CERTI-CRIMP, PRO-CRIMPER, MADISON CABLE and TYCO are trademarks.
TEFLON is a trademark of E.I. DuPont De Nemours and Company.
Other products, logos, and company names mentioned herein may be trademarks of their respective owners.
Feed-Thru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
MTA-156 Headers — UL94V-0
Flat — Straight Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Flat — Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Friction Lock — Straight Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Friction Lock — Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Polarized Lock — Straight Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Polarized Lock — Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Friction Lock — High Temperature, Straight Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Shrouded — Straight and Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
MTA-156 Quad Connectors—UL94V-0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54, 55
Closed End with Locking Ramp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Feed-Thru with Locking Ramp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
2
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
RRRRRRRRRRRRRRRRRRR
R
Crimp
SL-156
Crimp
AMP EP Connectors
Need more information?
Call Technical Support at the numbers listed below.
Technical Support is staffed with specialists well versed in Tyco Electronics products. They can provide you with:
Technical support
Catalogs
Technical Documents
Product Samples
Authorized Distributor
Locations
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Table of Contents (Continued)
MTA-156 Card Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56, 57
Connectors — UL94V-0
Closed End with and without Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Feed-Thru with and without Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
SL-156 Crimp Connectors and Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58-62
Wire-to-Board Mateability Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Wire-to-Board Crimp Contacts and Keying Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Wire-to-Board Housings — UL94V-0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Housings with Through Board Latch — UL94V-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Housings and Contacts for Large Insulation Diameter (LID) Wire . . . . . . . . . . . . . . . . . .62
AMP Economy Power (EP) Connector System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63-69
.156 [3.96] Centerline Connectors
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Crimp Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Plug Housings, Low-Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Low-Profile Headers — Straight and Right-Angle Posts . . . . . . . . . . . . . . . . . . . . . . . . . .65
Low-Profile Headers, High Temp. — Straight and Right-Angle Posts . . . . . . . . . . . . . . .66
.200 [5.08] Centerline Connectors
Plug Housings and Straight and Right-Angle Post Headers . . . . . . . . . . . . . . . . . . . . . .67
.312 [7.92] Centerline Connectors
Low-Profile Headers — Straight Posts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Single Connectors
1-Position Plug Housing and High-Profile Header — Straight Post . . . . . . . . . . . . . . . . .69
MTA Wire Selection and Ribbon Cable Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
IDC Ribbon Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71-74
MTA Wire Termination Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
MTA Application Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76-79
Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80-82
Global Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Connector Selection Guide
Contact Wire-to-
Product Name
.050" Centerline
MTA-50 IDC Connector .050 Kits and Headers 1.27 0.99
.100" Centerline
MTA-100 Connectors .100 and Headers 2.54 1.52
CST-100 II Contacts .100 and Housings 2.54 1.65
.156" Centerline
MTA-156 Connectors .156 and Headers 3.96 2.41
Quad Connectors
SL-156 Contacts .156 and Housings 3.96
SL-156 Large Ins. Dia. (LID) .156 Contacts and Housings 3.96 2.84
.156", .200" and .312" Centerlines
AMP Economy Power .200 (EP) Connector System 5.08 3.00
** When terminated one position at a time.
** Current Rating is application dependent.
Center-
Termin- Wire
line
ation Option (AWG) Dia. Max. (A)** Max. (VAC) Range (°C) Contacts
IDC Planned 2–28 30–26
IDC Yes 2–28 28–22
Crimp Planned 2–28 26–22
IDC Yes 2–24 26–18
.156
IDC No 2–12 22–18
3.96 2.41
Crimp No w/ through 24–18
Crimp No 2–24 24–16
.156
Crimp No 1–12 22–18
3.96 3.00 7.5 (2–12 Pos.)
Crimp No 2–12 22–18
.312
Crimp No 2–5 22–18
7.92 3.00
No. of
Positions
1–24; 2–10
board latch
Wire Wire Current Voltage Operating
Size Insulation Rating Rating Temp.
.039*
.060*
.065
.095*
.095*
.105
2.67
.112
.118 8 (1 pos.)
.118
.118
1 30 –55 to +105 V-0 & V-2 No
5 250 –55 to +105 V-0 & V-2 Yes
4 250 –55 to +105 V-0 Yes
7 600 –55 to +105 V-0 & V-2 Yes
12.5 600 –55 to +105 V-0 Yes
10 250 –25 to +105 V-0 Yes
10 250 –25 to +105 V-0 Yes
250 –25 to +105 V-0 Yes
7.5 (2–12 Pos.)
7.5 (2–5 Pos.)
250 –25 to +105 V-0 Yes
250 –25 to +105 V-0 Yes
UL
Flammability
Replace-
ment Approvals
3
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
MTA-50
.503
[12.78]
or
.254
[6.45]
Max. Vertical
Max. Right-Angle
.050 [1.27]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-50 IDC Connectors and Headers
Product Facts
2–28 contact positions
Connectors terminate 26,
28 and 30 AWG discrete wire or .050 [1.27] centerline rib­bon cable
Color-coded housings
Maximum cable insulation
diameter of .039 [0.99] with PVC insulation only
IDC contacts pre-loaded in
receptacle housing
30 V, 1 A contact rating
Contact design allows for
gold-to-gold or tin-to-tin interface
Contacts are lubricated to
prevent fretting corrosion
Wire feed-thru capability for
daisy-chain wiring or closed end for point-to-point wiring
Connectors are polarized for
proper mating
Manual and semiautomatic
application tooling
Mating heights shown below:
Component Recognized by
Underwriters Laboratories Inc. to US and Canadian Standards, File No. E28476
The MTA-50 IDC Connector System is a wire-to-printed cir­cuit board system with con­tacts in a staggered, single row on .050 [1.27] centerline. The design features wire feed­through capability for daisy­chain applications. Insulation displacement contacts are used to terminate a wide range of conductor sizes. Ribbon cable can also be ter­minated when the appropriate receptacle assembly and strain relief cover are used.
Header assemblies for board mount applications include right-angle (horizontal) and vertical mount products. These are available in
through-hole and surface mount configurations.
Typical uses of the MTA-50 IDC connectors would be in the Appliance, Commercial and Home Equipment and Security products industries.
See the following pages for related products:
Ribbon Cable (reels), .050
[1.27] centerline (p. 71)
Application Tooling (p. 76)
Cable Assemblies (p. 74)
Performance Data
Voltage Rating — 30 VAC Current Rating — 1 amp max. Low-Level Resistance
30 milliohms
MTA-50 IDC Connector Kit / Header Mateability Guide
Headers
Headers Headers
(Connectors and Headers) File No. E53793 (Ribbon Cable)
1445341 YYYY 1445344 YYYY 1445347 YYYY
These matrixes have been prepared to assist you in defining the correct mating halves for the MTA-50 header and connector kit combina­tion. Where a “Y” is indicated the combination is a valid mating pair.
Note: Tyco Electronics does NOT rec­ommend intermating connectors and headers with different contact plat­ings.
4
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
1445350 YYYY 1445353 YYYY 1445356 YYYY 1445359 YYYY 1445362 YYYY 1445365 YYYY
Connector Kits
1445368 YYYY 1445371 YYYY 1445374 YYYY
Matrix for Tin Plated Part Numbers
1445120
1445121
1445169
1445172
1445125
1445126
1445171
1445174
1445343 YY YY 1445346 YY YY 1445349 YY YY 1445352 YY YY 1445355 YY YY 1445358 YY YY 1445361 YY YY 1445364 YY YY 1445367 YY YY
Connector Kits
1445370 YY YY 1445373 YY YY 1445376 YY YY
Matrix for .000030 [0.00076] Gold Plated Part Numbers
Dielectric Withstanding Voltage
500 VAC Insulation Resistance
1,000 megohms Operating Temperature
–55°C to +105°C for connector only; cable rating may be lower
Technical Documents
Application Specification
114-13072 MTA-50 Connectors Product Specifications
108-2113 MTA-50 Connectors 100-4703 MADISON CABLE Cable
Specification (28 AWG, 7/36 Tinned copper, PVC insulation)
100-6257 MADISON CABLE Cable
Specification (28 AWG, 7/36 Tinned copper, TPO insulation)
1445170
1445124
1445123
1445342 YY Y Y 1445345 Y YYY 1445348 Y YYY 1445351 Y YYY 1445354 Y YYY 1445357 Y YYY 1445360 Y YYY 1445363 Y YYY 1445366 Y YYY
Connector Kits
1445369 Y YYY 1445372 Y YYY 1445375 Y YYY
Matrix for .000015 [0.00038] Gold Plated Part Numbers
1445173
A
± .004
[± 0.10]
(See Note 1)
.050
[1.27]
.035
[0.89]
.100
± .003
[2.54
± 0.08
]
.190
± .003
[4.83
± 0.08
]
Ref.
Ref.
Position 1
.150
[3.81]
.315
± .006
[8.00
± 0.15
]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-50 IDC Connectors and Headers (Continued)
Feed-Thru and Closed End Connectors
Material and Finish
Housing — UL 94V-2 rated, thermo-
plastic Contacts — Phosphor bronze;
.000100 [0.00254] min. tin in wire termination area, over .000050 [0.00127] min. nickel; choice on mating end: .000100 [0.00254] min. tin or .000030 [0.00076] gold or .000015 [0.00038] gold, over .000050 [0.00127] min. nickel
Color Coding by Wire Size for UL94V-0 Connectors
26 AWG — Blue 28 AWG — Green 30 AWG — Brown
For Strain Relief Covers see page 6. For mating Headers see pages 9 and 10. For Mateability Guide, see matrixes on page 4.
Receptacle Assemblies — Ribbon Cable
Connector Kits — Ribbon Cable
Notes:
1. To determine connector overall length (dim. A), multiply .050 x the number of circuits and add .082. Example: .050 x 10 circuits equals 0.50 + .082 = .582 [14.78].
2. Strain relief covers shown on page 6 are required and sold as part of the Connector Kit.
3. Stranded UL Style 1061 or equiv­alent wire is recommended.
4. Unless otherwise stated all toler­ances (except plating) to be ±.005 [±0.13].
5. Consult Product Drawing for RoHS Compliant information.
MTA-50
.050 [1.27]
Connector Kit Ordering Information
Connector Kit consists of Receptacle Assembly and Strain Relief Cover.
Base part number prefixes and suffixes indicate the number of circuit positions, for example: Base part num­ber 1445359
2 position = 0-1445359-2
28 position = 2-1445359-8
Note: Tin-plated connectors and headers in even position sizes from 2–12 and 18 are stocked parts; all other position sizes and products with gold-plated contacts are Make To Order.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
and
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Connector
Type &
Wire Size
Tin Plated
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
30 AWG
0.05–0.06 mm
.000030 [0.00076] Gold Plated
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
30 AWG
0.05–0.06 mm
.000015 [0.00038] Gold Plated
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
30 AWG
0.05–0.06 mm
2
2
2
2
2
2
2
2
2
Feed-Thru Closed End
Connector Kit No. of Connector Kit No. of
Part Nos. Circuits Part Nos. Circuits
1445359 2–28 1445368 2–28
1445362 2–28 1445371 2–28
1445365 2–28 1445374 2–28
1445361 2–28 1445370 2–28
1445364 2–28 1445373 2–28
1445367 2–28 1445376 2–28
1445360 2–28 1445369 2–28
1445363 2–28 1445372 2–28
1445366 2–28 1445375 2–28
5
MTA-50
.090
[2.29]
4 Plcs.
.040
[1.02]
.068
[1.73]
2 Plcs.
2 Plcs.
A
.255
[6.48]
.237
± .008
[6.02
± 0.20
]
.123
± .006
[3.12
± 0.15
]
.237
± .008
[6.02
± 0.20
]
A
.050 [1.27]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-50 IDC Connectors and Headers (Continued)
Connector Kits — Ribbon Cable (Continued)
Strain Relief Covers
Material and Finish
Strain Relief Cover — UL 94V-0
rated, thermoplastic, black
Feed-Thru
Feed-Thru
Closed End
Closed End
Feed-Thru and Closed End
No. of Circuits Dim. A No. of Circuits Dim. A
2
3
4
5
6
7
8
9
10
11
12
13
14
15
6
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
.260
6.60
.310
7.87
.360
9.14
.410
10.41
.460
11.68
.510
12.95
.560
14.22
.610
15.49
.660
16.76
.710
18.03
.760
19.30
.810
20.57
.860
21.84
.910
23.11
16
17
18
19
20
21
22
23
24
25
26
27
28
.960
24.38
1.010
25.65
1.060
26.92
1.110
28.19
1.160
29.46
1.210
30.73
1.260
32.00
1.310
33.27
1.360
34.54
1.410
35.81
1.460
37.08
1.510
38.35
1.560
39.62
A
± .004
[± 0.10]
(See Note 1)
.050
[1.27]
.035
[0.89]
.100
± .003
[2.54
± 0.08
]
.190
± .003
[4.83
± 0.08
]
Ref.
Ref.
Position 1
.150
[3.81]
.315
± .006
[8.00
± 0.15
]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-50 IDC Connectors and Headers (Continued)
Feed-Thru and Closed End Connectors
Material and Finish
Housing — UL 94V-2 rated, thermo-
plastic Contacts — Phosphor bronze;
.000100 [0.00254] min. tin in wire termination area, over .000050 [0.00127] min. nickel; choice on mating end: .000100 [0.00254] min. tin or .000030 [0.00076] gold or .000015 [0.00038] gold, over .000050 [0.00127] min. nickel
Color Coding by Wire Size for UL94V-0 Connectors
26 AWG — Blue 28 AWG — Green 30 AWG — Brown
For Strain Relief Covers see page 8. For mating Headers see pages 9 and 10. For Mateability Guide, see matrixes on page 4.
Receptacle Assemblies — Discrete Wire
Connector Kits — Discrete Wire
Notes:
1. To determine connector overall length (dim. A), multiply .050 x the number of circuits and add .082. Example: .050 x 10 circuits equals 0.50 + .082 = .582 [14.78].
2. Strain relief covers shown on page 8 are required and sold as part of the Connector Kit.
3. Stranded UL Style 1061 or equiv­alent wire is recommended.
4. Unless otherwise stated all toler­ances (except plating) to be ±.005 [±0.13].
5. Consult Product Drawing for RoHS Compliant information.
MTA-50
.050 [1.27]
Connector Kit Ordering Information
Connector Kit consists of Receptacle Assembly and Strain Relief Cover.
Base part number prefixes and suffixes indicate the number of circuit positions, for example: Base part num­ber 1445341
2 position = 0-1445341-2
28 position = 2-1445341-8
Note: Tin-plated connectors and headers in even position sizes from 2–12 and 18 are stocked parts; all other position sizes and products with gold-plated contacts are Make To Order.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
and
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Connector
Type &
Wire Size
Tin Plated
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
30 AWG
0.05–0.06 mm
.000030 [0.00076] Gold Plated
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
30 AWG
0.05–0.06 mm
.000015 [0.00038] Gold Plated
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
30 AWG
0.05–0.06 mm
Feed-Thru Closed End
Connector Kit No. of Connector Kit No. of
Part Nos. Circuits Part Nos. Circuits
1445341 2–28 1445350 2–28
2
1445344 2–28 1445353 2–28
2
1445347 2–28 1445356 2–28
2
1445343 2–28 1445352 2–28
2
1445346 2–28 1445355 2–28
2
1445349 2–28 1445358 2–28
2
1445342 2–28 1445351 2–28
2
1445345 2–28 1445354 2–28
2
1445348 2–28 1445357 2–28
2
7
MTA-50
.040
[1.02]
.068
[1.73]
.090
[2.29]
4 Plcs.
2 Plcs.
2 Plcs.
.255
[6.48]
.237
± .008
[6.02
± 0.20
]
A
.123
± .006
[3.12
± 0.15
]
.237
± .008
[6.02
± 0.20
]
A
.050 [1.27]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-50 IDC Connectors and Headers (Continued)
Connector Kits — Discrete Wire (Continued)
Strain Relief Covers
Material and Finish
Strain Relief Cover — UL 94V-0
rated, thermoplastic, black
Feed-Thru
Feed-Thru
Closed End
Closed End
Feed-Thru and Closed End
No. of Circuits Dim. A No. of Circuits Dim. A
2
3
4
5
6
7
8
9
10
11
12
13
14
15
8
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
.260
6.60
.310
7.87
.360
9.14
.410
10.41
.460
11.68
.510
12.95
.560
14.22
.610
15.49
.660
16.76
.710
18.03
.760
19.30
.810
20.57
.860
21.84
.910
23.11
16
17
18
19
20
21
22
23
24
25
26
27
28
.960
24.38
1.010
25.65
1.060
26.92
1.110
28.19
1.160
29.46
1.210
30.73
1.260
32.00
1.310
33.27
1.360
34.54
1.410
35.81
1.460
37.08
1.510
38.35
1.560
39.62
A
.035
[0.89]
.125
[3.18]
.016
[0.41]
.050
[1.27]
Ref.
Ref.
Ref.
Ref.
Circuit #1
.180
[4.57]
.220
± .003
[5.59
± 0.08
]
.035
[0.89]
Ref.
.035
[0.89]
Ref.
Circuit #1
.060
[1.52]
.125
[3.18]
A
Ref.
.050
[1.27]
.016
[0.41]
Ref.
Ref.
.035
[0.89]
.170
[4.32]
.220
± .003
[5.59
± 0.08
]
Ref.
.100
[2.54]
.035
[0.89]
.210
[5.33]
.050
[1.27]
.250*
[6.35]
.031
± .002
[0.78
± 0.05
]
Circuit #1
Typ.
Dia. Typ.
Recommended Mounting Hole Size and
Pattern for .062 [1.57] Thick PC Board
PCB Dimensions and RoHS Compliant information.
.100
[2.54]
.250*
[6.35]
.035
[0.89]
.068
[1.73]
.0705
[1.90]
* 6-circuit Dim. shown, refer to Product Drawing for actual
PCB Dimensions and RoHS Compliant information.
.050
[1.27]
.031
± .002
[0.78
± 0.05
]
.060
± .003
[1.52
± 0.08
]
Circuit #1
Typ.
Dia. Typ.
Dia.
Typ.
Recommended Mounting Hole Size and
Pattern for .062 [1.57] Thick PC Board
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-50 IDC Connectors and Headers (Continued)
Through-Hole Header Assemblies
Vertical
Material and Finish
Housing — UL 94V-0 rated, thermo-
plastic, black Contacts — Brass, .000100 [0.00254]
min. tin over .000050 [0.00127] min. nickel on solder legs; choice on mating end: .000100 [0.00254] min. tin or .000030 [0.00076] gold or .000015 [0.00038] gold, over .000050 [0.00127] min. nickel
Note: To determine header overall
length (dim. A), multiply .050 x the number of circuits and add .150. Example: .050 x 6 circuits equals .300 + .150 = .450 [11.43].
Base Part Numbers
Through-Hole
Header No. of
Part Nos. Posts
Standard UL 94V-0, Tin Plated
1445120 2–28
Standard UL 94V-0 .000030 [0.00076] Gold Plated
1445125 2–28
Standard UL 94V-0 .000015 [0.00038] Gold Plated
1445123 2–28
MTA-50
.050 [1.27]
Right-Angle
For mating Connector Kits see pages 5 through 8.
For mateability options, see matrixes on page 4.
Header Ordering Information
Base part number prefixes and suffixes indicate the number of circuit positions, for example: Base part num­ber 1445120
2 position = 0-1445120-2
28 position = 2-1445120-8
Note: Tin-plated connectors and headers in even position sizes from 2–12 and 18 are stocked parts; all other position sizes and products with gold-plated contacts are Make To Order.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
and
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Through-Hole
Header No. of
Part Nos. Posts
Standard UL 94V-0, Tin Plated
1445169 2–28
Standard UL 94V-0 .000030 [0.00076] Gold Plated
1445171 2–28
Standard UL 94V-0 .000015 [0.00038] Gold Plated
1445170 2–28
9
.035
[0.89]
Ref.
Circuit #1
A
.170
[4.32]
.249
[6.32]
.220
± .003
[5.59
± 0.08
]
Ref.
.162
[4.11]
.128
[3.25]
.100
[2.54]
* 6-circuit Dim. shown, refer to Product Drawing for actual
PCB Dimensions and RoHS Compliant information.
.050
[1.27]
Circuit #1
Typ.
.028
± .001
[0.71
± 0.03
]
.075
± .001
[1.91
± 0.03
]
.070
± .003
[1.78
± 0.08
]
2 Plcs.
.145
± .003
[3.68
± 0.08
]
2 Plcs.
.574*
[14.58]
Recommended PC Board Layout 
for use with .010 [0.25] Thick Stencil
Typ.
.162
[4.11]
.574*
[14.58]
.100
[2.54]
.100
[2.54]
* 6-circuit Dim. shown, refer to Product Drawing for actual 
PCB Dimensions and RoHS Compliant information.
.050
[1.27]
Circuit #1
Typ.
.100
[2.54]
Typ.
Typ.
Typ.
.028
± .001
[0.71
± 0.03
]
.065
± .001
[1.65
± 0.03
]
.070
± .003
[1.78
± 0.08
]
2 Plcs.
.145
± .003
[3.68
± 0.08
]
2 Plcs.
Recommended PC Board Layout 
for use with .010 [0.25] Thick Stencil
A
.050
[1.27]
.035
[0.89]
Ref.
Ref.
Circuit #1
.180
[4.57]
.270
[6.86]
.220
± .003
[5.59
± 0.08
]
Ref.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-50 IDC Connectors and Headers (Continued)
MTA-50
.050 [1.27]
Surface Mount Header Assemblies
Vertical
Material and Finish
Housing — UL 94V-0 rated, thermo-
plastic, black Contacts — Brass, .000100 [0.00254]
min. tin over .000050 [0.00127] min. nickel on solder pads; choice on mating end: .000100 [0.00254] min. tin or .000030 [0.00076] gold or .000015 [0.00038] gold, over .000050 [0.00127] min. nickel
Boardlock — Phosphor bronze, tin plated .000100 [0.000254] min. over .000050 [0.00127] min. nickel
Right-Angle
Note: To determine header overall
length (dim. A), multiply .050 x the number of circuits and add .150. Example: .050 x 6 circuits equals .300 + .150 = .450 [11.43].
Base Part Numbers
Surface Mount
Header No. of
Part Nos. Posts
Standard UL 94V-0, Tin Plated
1445121 2–28
Standard UL 94V-0 .000030 [0.00076] Gold Plated
1445126 2–28
Standard UL 94V-0 .000015 [0.00038] Gold Plated
1445124 2–28
Note: All SMT product is pre-
packaged in standard tape and reel format.
For mating Connector Kits see pages 5 through 8.
For mateability options, see matrixes on page 4.
Header Ordering Information
Base part number prefixes and suffixes indicate the number of circuit positions, for example: Base part num­ber 1445121
2 position = 0-1445121-2
28 position = 2-1445121-8
and
Note: Tin-plated connectors and headers in even position sizes from 2–12 and 18 are stocked parts; all other position sizes and products with gold-plated contacts are Make To Order.
10
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Surface Mount
Header No. of
Part Nos. Posts
Standard UL 94V-0, Tin Plated
1445172 2–28
Standard UL 94V-0 .000030 [0.00076] Gold Plated
1445174 2–28
Standard UL 94V-0 .000015 [0.00038] Gold Plated
1445173 2–28
R
R
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
.100 [2.54] Centerline MTA-100 IDC Connectors and Headers
Product Facts
Connectors and headers for
2 through 28 positions; wire sizes of 22, 24, 26 and 28 AWG [0.4-0.08 mm
Wire-to-Post Connectors
preloaded with dual beam contacts
Connectors and headers,
except shrouded headers, are end-to-end stackable
Connector styles include
both closed end and feed­thru connectors with locking ramps, with and without polarizing tabs
Molded ribs on housing do
not allow reverse mating
Posted connectors for 2
through 19 positions
Connectors preloaded with
IDC contacts
All contacts are slotted for
insulation displacement (IDC) terminal technique
Contacts are lubricated for
fretting corrosion protection
Benefits derived from the
MTA-100 system include increased quality and ease of handling such as—
One-step assembly
No wire stripping
No contact damage
Reduced wiring errors
Simpler tooling
Simple maintenance and
repair
Meets the material require-
ments of Table 23.1 of UL1410 Standards for Television Receiver and Video Products (wire-to­post connectors only)
Recognized under the
Component Program of Underwriters Laboratories Inc., File No. E28476
Certified by Canadian
Standards Association, File No. LR7189
Technical Documents
Product Specification
108-1050 MTA-100 Connectors
Application Specifications
114-1019 MTA-100 Connectors 114-1031 MTA-100 Ribbon Cable
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Assembly
2
]
MTA-100 connectors accept discrete and ribbon cable wire sizes ranging from 22 – 28 AWG [0.4 –
0.08 mm
2
] with maximum insulation outside diameter of .060 [1.52] for terminat­ing single wire and .050 [1.27] for mass termination of wires. Tin plated solid, fused stranded, or stranded (7 strands) wire with PVC insulation can be used on 22 – 28 AWG [0.4 – 0.9 mm MTA-100 connectors and 19 stranded wire on 22–24 AWG [0.4– 0.2 mm MTA-100 connectors. Only
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
one wire to be terminated into an IDC contact slot.
The wire-to-post connector housing material is flame retardant thermoplastic, either UL94V-2 or UL94V-0 rated.
A full line of .100 [2.54] centerline headers com­pletes the system. Headers are available with straight or right-angle posts, in flat,
2
polarized or friction lock
]
styles. Headers are avail­able in 2 through 28
2
positions. Shrouded headers
]
are available in 2 through 14 positions.
Performance Data*
Voltage Rating —250 vac Current Rating — 5 amp max. Low-Level Resistance
6 mmax. initial Dielectric Withstanding Voltage
750 vac/1 min. Insulation Resistance
5000 Mmin. initial Operating Temperature
55C to 105C
Note: Refer to page 70 for approved wire listings.
*Refer to the Product Specification for additional electrical, mechanical and environmental performance tests and requirements.
11
MTA-100
.100 [2.54]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Connector/Header Mateability Guide
This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 header and connector combination.Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
MTA-100
.100 [2.54]
Matrix for Tin Plated Part Numbers
Headers
640452
640453
640454
640455
640456
640457
644456
644457
644486
644488
644694
644695
644803
644861
644874
640440 YYYYYYYYYYYYYYYYYYN 640441 YYYYYYYYYYYYYYYYYYN 640442 YYYYYYYYYYYYYYYYYYN 640443 YYYYYYYYYYYYYYYYYYN 640468 YYYYYYYYYYYYYYYYYYN 640469 YYYYYYYYYYYYYYYYYYN 640470 YYYYYYYYYYYYYYYYYYN 640471 YYYYYYYYYYYYYYYYYYN 640620 YYYYYYYYYYYYYYYYYYN 640621 YYYYYYYYYYYYYYYYYYN 640622 YYYYYYYYYYYYYYYYYYN 640623 YYYYYYYYYYYYYYYYYYN 641311 YYYYYYYYYYYYYYYYYYN 641312 YYYYYYYYYYYYYYYYYYN 641313 YYYYYYYYYYYYYYYYYYN 641314 YYYYYYYYYYYYYYYYYYN 641534 YYYYYYYYYYYYYYYYYYN 641535 YYYYYYYYYYYYYYYYYYN 641536 YYYYYYYYYYYYYYYYYYN 641537 YYYYYYYYYYYYYYYYYYN 641653 YYYYYYYYYYYYYYYYYYN 641654 YYYYYYYYYYYYYYYYYYN 641655 YYYYYYYYYYYYYYYYYYN 641656 YYYYYYYYYYYYYYYYYYN 643498 YYYYYYYYYYYYYYYYYYN 643813 YYYYYYYYYYYYYYYYYYN 643814 YYYYYYYYYYYYYYYYYYN
Connectors
643815 YYYYYYYYYYYYYYYYYYN 643816 YYYYYYYYYYYYYYYYYYN 643828 YYYYYYYYYYYYYYYYYYN 644083 YYYYYYYYYYYYYYYYYYN 644312 YYYYYYYYYYYYYYYYYYN 644313 YYYYYYYYYYYYYYYYYYN 644497 YYYYYYYYYYYYYYYYYYN 644511 YYYYYYYYYYYYYYYYYYN 644512 YYYYYYYYYYYYYYYYYYN 644513 YYYYYYYYYYYYYYYYYYN 644514 YYYYYYYYYYYYYYYYYYN 644540 YYYYYYYYYYYYYYYYYYN 644563 YYYYYYYYYYYYYYYYYYN 644564 YYYYYYYYYYYYYYYYYYN 644565 YYYYYYYYYYYYYYYYYYN 644574 YYYYYYYYYYYYYYYYYYN 644575 YYYYYYYYYYYYYYYYYYN 644576 YYYYYYYYYYYYYYYYYYN 644577 YYYYYYYYYYYYYYYYYYN 644578 YYYYYYYYYYYYYYYYYYN 644579 YYYYYYYYYYYYYYYYYYN 644795 YYYYYYYYYYYYYYYYYYN
*1375820 YY YYYYYYNNYYNNYYYYY
*Select contact plating to match header plating.
644875
644876
644877
644892
644893
644894
647047
647048
647050
647051
647106
647166
NNYYYYY YYYYYYY NNYYYYY YYYYYYY N N YYY YY YY YYY Y Y NNYYYYY YYYYYYY NNYYYYY YYYYYYY N N YYY YY YY YYY Y Y N N YYY YY YY YYY Y Y NNYYYYY YYYYYYY NNYYYYY YYYYYYY N N YYY YY YY YYY Y Y NNYYYYY YYYYYYY NNYYYYY YYYYYYY N N YYY YY YY YYY Y Y N N YYY YY YY YYY Y Y NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY NNYYYYY YYYYYYY YYYYYYYYYYYYYY
647502
647531
647609
647623
647532
1744075
12
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Connector/Header Mateability Guide (Continued)
This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 header and connector combination.Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
Matrix for .000030 [0.00076] Gold Plated Part Numbers
Matrix for .000015 [0.00038] Gold Plated Part Numbers
Headers
641211
641212
641213
641214
641215
641216
644487
644489
644884
644885
644886
644887
644896
644897
641237 YY YYYYYYYYY YN NNYYY 641238 YY YYYYYYYYY YN NNYYY 641239 YY YYYYYYYYY YN NNYYY 641240 YY YYYYYYYYY YN NNYYY 641241 YY YYYYYYYYY YN NNYYY 641242 YY YYYYYYYYY YN NNYYY 641243 YY YYYYYYYYY YN NNYYY 641244 YY YYYYYYYYY YN NNYYY 644020 YY YYYYYYYYY YN NNYYY
Connectors
644042 YY YYYYYYYYY YN NNYYY 644043 YY YYYYYYYYY YN NNYYY 644044 YY YYYYYYYYY YN NNYYY 644702 YY YYYYYYYYY YN NNYYY 644726 YY YYYYYYYYY YN NNYYY
*1375820 YYYYYYNNYYYYYYYYYY
Headers
644898
647108
647626
647117
647168
647624
647109
647116
647114
YYYYYYYY YYYYYYYY Y YYYYYYY YYYYYYYY YYYYYYYY Y YYYYYYY Y YYYYYYY YYYYYYYY YYYYYYYY Y YYYYYYY YYYYYYYY YYYYYYYY Y YYYYYYY Y YYYYYYY YYYYYYYY
647534
1744047
1744163
MTA-100
.100 [2.54]
647625
647533
641122
641123
641124
641125
641126
641127
644888
644889
644890
644891
647075
641190 YY YYYYYYYYY YYYY YYYYY Y 641191 YY YYYYYYYYY YYYY YYYYY Y 641192 YY YYYYYYYYY YYYY YYYYY Y 641193 YY YYYYYYYYY YYYY YYYYY Y 641198 YY YYYYYYYYY YYYY YYYYY Y 641199 YY YYYYYYYYY YYYY YYYYY Y 641200 YY YYYYYYYYY YYYY YYYYY Y 641201 YY YYYYYYYYY YYYY YYYYY Y
Connectors
644038 YY YYYYYYYYY YYYY YYYYY Y 644040 YY YYYYYYYYY YYYY YYYYY Y 647477 YY YYYYYYYYY YYYY YYYYY Y 647480 YY YYYYYYYYY YYYY YYYYY Y
*1375820 NNNNNNNN NNN NN NN NNNNY Y
1744020 YYYYYYYY YYY YY YY YYYYY Y
*Select contact plating to match header plating.
647076
647078
647107
647079
647167
647467
647627
1744074
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
13
.520
[13.21]
.275
[6.99]
.075
[1.91]
.245
[6.22]
.275
[6.99]
.184
[4.67]
.100
[2.54]
Typ.
A
.056
[1.42]
.075
[1.91]
.228
[5.80]
.520
[13.21]
.275
[6.99]
.075
[1.91]
.245
[6.22]
.305
[7.75]
.184
[4.67]
.100
[2.54]
Typ.
A
.056
[1.42]
.075
[1.91]
.228
[5.80]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 IDC Connectors—Closed End and Feed-Thru
MTA-100
.100 [2.54]
Material and Finish
Housing — UL94V-2 rated, nylon, see
below for color; or UL94V-0 rated, nylon, black
Contacts — Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [0.00038] post gold-plated over nickel
Color Coding by Wire Size for UL94V-2 Connectors
28 AWG—Green 26 AWG—Blue 24 AWG—White 22 AWG—Red
All wire sizes in UL94V-0
Black
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 20 thru 30.
Notes:
1. Refer to pages 70-74 for approved wire listing.
2. For strain reliefs and dust covers, see page 16.
3. For keying plugs, see page 17.
4. Other circuit sizes are available upon request. Minimums may apply.
5. Connector circuits can be molded closed for keying purposes. Minimums may apply.
6. Where no part numbers appear in the chart, par ts can be made available upon request. Minimums may apply.
7. To determine connector overall length (dim. A), multiply .100 x the number of circuits. Example: .100 x 10 circuits equals 1.000 inch [25.4 mm].
Closed End Connectors
Without Polarizing Tabs
With Polarizing Tabs
Feed-Thru Connectors
Without Polarizing Tabs
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
14
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
With Polarizing Tabs
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 IDC Connectors—Closed End and Feed-Thru (Continued)
Connector Ordering Information
The “Base Part Numbers” Chart at right shows the base part number, and their RoHS (Restrictions on Certain Hazardous Substances) Compliant (lead free) equivalent avail­able for the described con­nectors.
Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 10-position closed end con­nector without polarizing tabs for 22 AWG wire would be:
Base number 640440 plus
prefix-and-suffix
4- -0
The correct ordering num­ber is 4-640440-0
All part numbers are the RoHS equivalent version. Example:
No. of
Pos.
2 3-640440-2 3 3-640440-3 4 3-640440-4 5 3-640440-5 6 3-640440-6 7 3-640440-7 8 3-640440-8
9 3-640440-9 10 4-640440-0 11 4-640440-1 12 4-640440-2 13 4-640440-3 14 4-640440-4 15 4-640440-5 16 4-640440-6 17 4-640440-7 18 4-640440-8 19 4-640440-9 20 5-640440-0 21 5-640440-1 22 5-640440-2 23 5-640440-3 24 5-640440-4 25 5-640440-5 26 5-640440-6 27 5-640440-7 28 5-640440-8
Note: All RoHS equivalent part num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Lead Free
RoHS
Prefix/Suffix
Base Part Numbers
Closed End Feed-Thru
Connector Type
& Wire Size
Standard UL94V-2, Tin Plated
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
2
2
2
2
Tape Mounted on Reel UL94V-2, Tin Plated
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
2
2
2
2
Standard UL94V-2, .000030 [0.00076] Gold Plated
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
28 AWG
0.8–0.9 mm
2
2
2
2
Standard UL94V-2, .000015 [0.00038] Gold Plated
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
2
2
2
2
LED*, UL94V-2, Tin Plated (See Note 1)
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
28 AWG
0.08–0.09 mm
2
2
2
2
Standard UL94V-0, Tin Plated (Gold is available, minimums may apply.) (Black in color)
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
*LED connectors are designed to mate with .014–.020 [0.36–0.51] diameter posts or square leads.
1
Other circuit sizes are available upon request. Minimums may apply.
2
Tape mounted.
2
2
2
Note: Blocked circuit configurations are available. Contact product engineer or product manager for details. Minimums may apply.
Without Tabs With Tabs Without Tabs With Tabs
Connector RoHS Connector RoHS Connector RoHS Connector RoHS Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
640440 32–58 643813 32–58 640620 32–58 644540
1
640441 32–58 643814 32–58 640621 32–58 644563132–54
640442 32–58 643815 32–58 640622 32–58 644564132–45
640443 32–58 643816 32–58 640623 32–58 644565132–45
640468 32–58 644511 42–68 641311 32–58 ——
640469 32–58 644512 32–58 641312 32–58 ——
640470 32–58 644513 32–58 641313 32–58 ——
640471 32–58 644514 32–58 641314 32–58 ——
641237 32–58 644042 32–58 641241 32–58 644702
1
641238 32–58 644020 32–58 641242 32–58 ——
641239 32–58 644043132–44 641243 32–58 644726132–45
641240 32–58 644044132–44 641244 32–58 ——
1
641190 32–58 644038
32–44 641198 32–58 647477 32–46
641191 32–58 1744020132–44 641199 32–58 ——
641192 32–58 644040132–44 641200 32–58 647480 32–43
641193 32–58 ——641201 32–58 ——
641534 32–33 ——641653 32–33 ——
641535 32–33 644795 32–33 641654 32–33 ——
641536 32–33 ——641655 32–33 ——
641537 32–33 ——641656 32–33 ——
1
643498
32–45 644083132–45 644575132–45 644578132–45
644574132–45 644312132–45 644576132–45 644579132–45
643828132–45 644313132–45 644577132–45 644497132–45
32–45
32–45
MTA-100
.100 [2.54]
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
15
.340
[8.64]
.345
[8.76]
.127
[3.23]
Note: This portion of the front locking bar  may or may not be present.
A
A
.130
[3.3]
.105
[2.67]
.360
[9.14]
Retention Dimple
.335
[8.51]
.360
[9.14]
Note: This portion of the front locking bar may or may not be present.
A
.127
[3.23]
A
.130
[3.3]
.245
[6.22]
.395
[10.03]
Retention Dimple
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 IDC Connector Accessories
MTA-100
.100 [2.54]
Covers
Material (RoHS Compliant)
Strain Relief Cover — UL94V-2
rated, nylon, white Dust Covers — UL94V-0 rated,
polyester, white
Cover Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described cover.
Prefixes and suffixes are determined by the number of circuit positions in the cover. For example, the complete part number for a 10-position closed end strain relief cover would be:
Base number 643075 plus
prefix-and-suffix
1- -0
The correct ordering num­ber is
1-643075-0
Closed End Strain Relief Covers
Feed-Thru Strain Relief Covers
Closed End Dust Covers
Feed-Thru Dust Covers
Base Part Numbers
Closed End Feed-Thru
Strain Relief Dust Strain Relief Dust
Covers Covers Covers Covers
Cover No. of Cover No. of Cover No. of Cover No. of
Part Nos. Circuits Part Nos. Circuits Part Nos. Circuits Part Nos. Circuits
643075 2–28 640550 2–28 643077 2–28 640642 3-28
Cover Length
No. of Dim. Prefix/
Circuits A Suffix
.200
5.08
.300
7.62
.400
10.16
.500
12.7
.600
15.24
.700
17.78
.800
20.32
-2
-3
-4
-5
-6
-7
-8
2
3
4
5
6
7
8
16
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
No. of Dim. Prefix/
Circuits A Suffix
9
10
11
12
13
14
15
.900
22.86
1.00
25.4
1.100
27.94
1.200
30.48
1.300
33.02
1.400
35.56
1.500
38.1
-9
1- -0
1- -1
1- -2
1- -3
1- -4
1- -5
No. of Dim. Prefix/
Circuits A Suffix
16
17
18
19
20
21
22
1.600
40.64
1.700
43.18
1.800
45.72
1.900
48.26
2.000
50.8
2.100
53.34
2.200
55.88
1- -6
1- -7
1- -8
1- -9
2- -0
2- -1
2- -2
No. of Dim. Prefix/
Circuits A Suffix
23
24
25
26
27
28
2.300
58.42
2.400
60.96
2.500
63.5
2.600
66.04
2.700
68.58
2.800
71.12
2- -3
2- -4
2- -5
2- -6
2- -7
2- -8
.125
[3.18]
.038
[0.97]
.077
[1.96]
.065
[1.65]
.300
[7.62]
.500
[12.7]
.027
[0.69]
Sq.
Ref.
1.800
[45.72]
Ref.
2
.452
[11.48]
.075
[1.91]
.070
[1.78]
.070
[1.78]
.142
[3.61]
Max.
.425
[10.8]
Keying Plug with Carrier Strip (10 plugs per strip)
Part No. 641994-1
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 IDC Connector Accessories (Continued)
Material (RoHS Compliant)
UL94V-2 rated, nylon, natural color
Note: Removal of contact is not necessary when using keying plug.
Replacement IDC Contacts
Material and Finish
Phosphor bronze, post tin plated; .000030 [0.00076] or .000015 [0.00038] post gold plated over nickel
Wire Size
AWG mm
22 0.3–0.4 640636-3 641186-4 641186-3 641643-2 24 0.2 640637-3 641187-4 641187-3 641644-2 26 0.12–0.15 640638-3 641188-4 641188-3 641645-2 28 0.08–0.09 640639-2 641189-4 641189-3 641646-2
2
Standard .000030 [0.00076] .000015 [0.00038] LED
Tin Plated Gold Plated Gold Plated Tin Plated
Part Numbers
MTA-100
.100 [2.54]
Note: Tyco Electronics does not rec-
ommend terminating an MTA contact more than one time. Use replacement contacts when required for field repairs or wire changes.
Crimp Snap-In Contacts
Material and Finish
Phosphor bronze, tin plated
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Wire Size Part Nos.
AWG mm2Loose Piece* Strip**
26-22 0.12–0.4 640709-2 640708-2
**Hand Tool No. 59836-1 (IS 408-6527) **Applicator No. 466747-1 (IS 408-8040)
Special applications for crimp snap-in contacts are:
1. Double wire per contact
2. Coax or shielded wire
3. Mixed wire size in same connector
Note: Only one crimp snap-in contact per connector.
Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
17
MTA-100
.100 [2.54]
Matrix for Tin Plated Part Numbers
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Posted Connector/Connector Mateability Guide
This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not accept­able for mating.
Posted Connectors
647000
647001
647002
647003
647004
647005
647006
647007
640440 YY YYYYYY 640441 YY YYYYYY 640442 YY YYYYYY 640443 YY YYYYYY 640468 YY YYYYYY 640469 YY YYYYYY 640470 YY YYYYYY 640471 YY YYYYYY 640620 YY YYYYYY 640621 YY YYYYYY 640622 YY YYYYYY 640623 YY YYYYYY 641311 YY YYYYYY 641312 YY YYYYYY 641313 YY YYYYYY 641314 YY YYYYYY 641534 YY YYYYYY 641535 YY YYYYYY 641536 YY YYYYYY 641537 YY YYYYYY 641653 YY YYYYYY 641654 YY YYYYYY 641655 YY YYYYYY 641656 YY YYYYYY 643498 YY YYYYYY 643813 Y* Y* Y* Y* Y* Y* Y* Y* 643814 Y* Y* Y* Y* Y* Y* Y* Y*
Connectors
643815 Y* Y* Y* Y* Y* Y* Y* Y* 643816 Y* Y* Y* Y* Y* Y* Y* Y* 643828 YY YYYYYY 644083 Y* Y* Y* Y* Y* Y* Y* Y* 644312 Y* Y* Y* Y* Y* Y* Y* Y* 644313 Y* Y* Y* Y* Y* Y* Y* Y* 644497 Y* Y* Y* Y* Y* Y* Y* Y* 644511 Y* Y* Y* Y* Y* Y* Y* Y* 644512 Y* Y* Y* Y* Y* Y* Y* Y* 644513 Y* Y* Y* Y* Y* Y* Y* Y* 644514 Y* Y* Y* Y* Y* Y* Y* Y* 644540 Y* Y* Y* Y* Y* Y* Y* Y* 644563 Y* Y* Y* Y* Y* Y* Y* Y* 644564 Y* Y* Y* Y* Y* Y* Y* Y* 644565 Y* Y* Y* Y* Y* Y* Y* Y* 644574 YY YYYYYY 644575 YY YYYYYY 644576 YY YYYYYY 644577 YY YYYYYY 644578 Y* Y* Y* Y* Y* Y* Y* Y* 644579 Y* Y* Y* Y* Y* Y* Y* Y* 644795 Y* Y* Y* Y* Y* Y* Y* Y* 1375820 NNNNNNNN
*2 & 3 position MTA-100 Posted Connectors can not mate with MTA-100
connectors with polarizing tabs.
18
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Matrix for .000030 [0.00076] Gold Plated Part Numbers
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Posted Connector/Connector Mateability Guide (Continued)
This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not accept­able for mating.
Posted Connectors
647008
647009
647010
647011
647012
647013
647014
647015
641237 YY YYYYYY 641238 YY YYYYYY 641239 YY YYYYYY 641240 YY YYYYYY 641241 YY YYYYYY 641242 YY YYYYYY 641243 YY YYYYYY 641244 YY YYYYYY 644020 Y* Y* Y* Y* Y* Y* Y* Y* 644042 Y* Y* Y* Y* Y* Y* Y* Y*
Connectors
644043 Y* Y* Y* Y* Y* Y* Y* Y* 644044 Y* Y* Y* Y* Y* Y* Y* Y* 644702 Y* Y* Y* Y* Y* Y* Y* Y* 644726 Y* Y* Y* Y* Y* Y* Y* Y* 1375820 NNNNNNNN
*2 & 3 position MTA-100 Posted Connectors can not mate with MTA-100
connectors with polarizing tabs.
MTA-100
.100 [2.54]
Matrix for .000015 [0.00038] Gold Plated Part Numbers
Posted Connectors
647008
647009
647010
647011
647012
647013
647014
647015
641190 YY YYYYYY 641191 YY YYYYYY 641192 YY YYYYYY 641193 YY YYYYYY 641198 YY YYYYYY 641199 YY YYYYYY 641200 YY YYYYYY 641201 YY YYYYYY 644038 Y* Y* Y* Y* Y* Y* Y* Y*
Connectors
644040 Y* Y* Y* Y* Y* Y* Y* Y* 647477 Y* Y* Y* Y* Y* Y* Y* Y* 647480 Y* Y* Y* Y* Y* Y* Y* Y* 1375820 NNN NNNNN 1744020 Y* Y* Y* Y* Y* Y* Y* Y*
*2 & 3 position MTA-100 Posted Connectors can not mate with MTA-100
connectors with polarizing tabs.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
19
.843
[21.40]
B
Dim.
.303
[7.70]
.079
[2.00]
.415
.025
[0.54]
Sq.
.100
[2.54]
Typ.
A Dim.
.843
[21.40]
B
Dim.
.303
[7.70]
.079
[2.00]
.415
.025
[0.54]
Sq.
.100
[2.54]
Ty p.
A Dim.
.083
[2.10]
.770
[19.55]
.075
[1.91]
.025
[0.64]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 IDC Posted Connectors (Wire-to-Wire)—Closed End, Feed-Thru
MTA-100
.100 [2.54]
20
Material and Finish
Closed End Feed-Thru
Housing — UL 94V-2 rated, nylon, see
chart for color Contacts — Copper alloy, post tin or
gold plated over nickel (see chart)
Notes:
1. Mating half visuals - pages 14 & 15.
2. Use feed thru strain relief covers & feed thru dust covers (if needed) - page 16.
3. Approved wire listing - pages 70 thru 74.
Base Part Numbers
Connector Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are determined by the number of circuit positions in the connec­tor. For example, the complete part number for a 12-position closed end connector for 22 AWG wire would be:
Base number 647000 plus
prefix-and-suffix
4- -2
The correct ordering number is
4-647000-2
All part numbers are the RoHS equivalent version. Example:
No. of
Pos.
2 3-647000-2
19 4-647000-9
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Lead Free
RoHS
Prefix/Suffix
thru
Color Coding by Wire Size for UL 94V-2 Connectors 22 AWG—Red 24 AWG—White 26 AWG—Blue 28 AWG—Green
Performance Data
Voltage Rating — 250 VAC Current Rating — 4 amp max. Low-Level Resistance
16 mmax. initial Dielectric Withstanding Voltage
750 VAC/1 min. Insulation Resistance — 5000 M
min. initial Operating Temperature
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
Connector Type
& Wire Size
Standard UL 94V-2, Tin Plated
22 AWG
24 AWG
2
0.2 mm
26 AWG
28 AWG
22 AWG
24 AWG
2
0.2 mm
26 AWG
28 AWG
22 AWG
24 AWG
2
0.2 mm
26 AWG
28 AWG
Dim.
AB
.300 .227
[7.62] [5.77]
.400 .327
[10.16] [8.31]
.500 .427
[12.70] [10.85]
.600 .527
[15.24] [13.39]
2
2
2
2
2
2
2
2
2
0.3–0.4 mm
0.12–0.15 mm
0.08–0.09 mm
Standard UL 94V-2, .000030 [0.00076] Gold Plated
0.3–0.4 mm
0.12–0.15 mm
0.08–0.09 mm
Standard UL 94V-2, .000015 [0.00038] Gold Plated
0.3–0.4 mm
0.12–0.15 mm
0.08–0.09 mm
1
2 and 3 position MTA-100 Posted Connectors (Closed End) can not mate with MTA-100 connectors with polarizing tabs.
2
Parts may be manufactured upon request. Minimums may apply. Contact product engineer or product manager for details.
No. of
Circuits
2
3
4
5
–55°C to +105°C
Technical Documents
Product Specification
108-1050-1 MTA-100 Posted
Connector
Application Specification
114-1019 MTA-100 Connectors
Replacement IDC Contacts
Material and Finish
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Closed End Connector Feed-Thru Connector
Part Nos. RoHS Equiv. Part Nos. No. of Circuits
647000 647004
647001 32–49
647002 32–49
647003 32–49
647008 32–49
647009 32–49
647010 32–49
647011 32–49
647016 32–49
647017 32–49
647018 32–49
647019 32–49
No. of
Circuits
6
7
8
9
Dim.
AB
.700 .627
[17.78] [15.93]
.800 .727
[20.32] [18.47]
.900 .827
[22.86] [21.01]
1.000 .927
[25.40] [23.55]
Contacts — Copper alloy, post tin or gold plated over nickel
32–49
1
1
1
1
1
1
1
1
1
1
1
1
No. of
Circuits
10
11
12
13
647005
647006
647007
647012
647013
647014
647015
647020
647021
647022
647023
Dim.
AB
1.100 1.027
[27.94] [26.09]
1.200 1.127
[30.48] [28.63]
1.300 1.227
[33.02] [31.17]
1.400 1.327
[35.56] [33.71]
Wire Size
AWG mm2Plated [.00076]
22 0.3–0.4 3-647030-1 3-647030-2
24 0.2 3-647031-1 3-647031-2
26 0.12–0.15 3-647032-1 3-647032-2
28 0.8–0.9 3-647033-1 3-647033-2
No. of
Circuits
14
15
16
17
18
19
2
2
2
2
2
2
2
2
2
2
2
2
Dim.
AB
1.500 1.427
[38.10] [36.25]
1.600 1.527
[40.64] [38.79]
1.700 1.627
[43.18] [41.33]
1.800 1.727
[45.72] [43.87]
1.900 1.827
[48.26] [46.41]
2.000 1.927
[50.80] [48.95]
Part Numbers
Tin .000030
Gold Plated
.200
[5.08]
A
.025
[0.64]
Sq.
.100
[2.54]
Typ.
.050
[1.27]
Typ.
Post No. 1
.295
[7.49]
.100
[2.54]
.140
[3.56]
Ref.
.535
[13.59]
.200
[5.08]
A
.100
[2.54]
.025
[0.64]
Sq.
.050
[1.27]
Typ.
.100
[2.54]
Typ.
.140
[3.56]
Ref.
.295
[7.49]
.062
[1.57]
Post No. 1
.100
[2.54]
Typ.
.050/.040
[1.27/1.02]
Edge of Board
.120
[3.05]
Min.
Dia.
.100
[2.54]
Typ.
.050/.040
[1.27/1.02]
Edge of Board
X
Dia.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Flat Headers—Straight and Right-Angle
Material and Finish
Straight Post (.025 [0.64] Square)
Right-Angle Post (.025 [0.64] Square)
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
3. To determine header overall
length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be:
Base number 641211 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-641211-0
All part numbers are the RoHS equivalent version. Example:
Lead Free
RoHS
Prefix/Suffix
thru
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
No. of
Pos.
2 3-641211–2
28 5-641211-8
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
Base Part Numbers
Straight Posts Right-Angle Posts
Header No. of Posts/ Header No. of Posts/
Part Nos. RoHS Equiv. Part Nos. RoHS Equiv.
Standard UL94V-0, Tin Plated
640452 2–28 640453 2–28
Standard UL94V-0, .000030 [0.00076] Gold Plated
641211
Standard UL94V-0, .000015 [0.00038] Gold Plated
641122
2–28
32–58 32–58
2–28
32–58 32–58
X = .120 [3.05] min., .240 [6.1] max.
when mated with MTA-100 Connector.
X = .120 [3.05] min., when mated with
CST-100 II Connector.
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
Note: Consult Product Drawing for details
on placing headers onto PC boards.
641212
641123
2–28
2–28
21
MTA-100
.100 [2.54]
.044
[1.12]
Typ.
.100
[2.54]
.100
[2.54]
Typ.
A
.092
[2.34]
.150
[3.81]
.260 [6.6]
.110
[2.79]
Ref.
.025
[0.64]
Sq.
Post No. 1
.044
[1.12]
Typ.
.100
[2.54]
Post No. 1
.100
[2.54]
Typ.
.295
[7.49]
.505
[12.83]
.110
[2.79]
Ref.
A
.092
[2.34]
.025
[0.64]
Sq.
.110
[2.79]
Ref.
.0335 [0.85]
.100
[2.54]
Typ.
.050/.040
[1.27/1.02]
Edge of Board
.060
[1.52]
Min.
Dia. For Straight Leg Headers
Dia. For Retentive Leg Headers
.037
[0.94 ]
± .002 ± 0.05
.100
[2.54]
Typ.
Edge of Board
.060
[1.52]
Min.
.050/.040
[1.27/1.02]
Dia. For Straight Leg Headers
Dia. For Retentive Leg Headers
.037
[0.94 ]
± .002 ± 0.05
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Narrow Flat Headers—Straight and Right-Angle
MTA-100
.100 [2.54]
Material and Finish
Straight Post (.025 [0.64] Square)
Right-Angle Post (.025 [0.64] Square)
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Headers without retentive legs are
suitable for breakaway application.
3. 2 or 3 retentive leg(s) per header,
depending upon number of positions.
Straight and Right-Angle Post with Retentive Legs
4. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
5. To determine header overall
length (dim. A) multiply .100 x the number of posts minus (–) .012. Example: .100 x 10 posts – .012 = .988 inches [25.1 mm].
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Connector Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts and without retentive legs would be:
Base number 644456 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-644456-0
All part numbers are the RoHS equivalent version. Example:
Lead Free
RoHS
Prefix/Suffix
thru
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
No. of
Pos.
2 3-644456-2
28 5-644456-8
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
22
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Recommended Mounting Hole Pattern for .062
[1.57] Thk. PC Board
Recommended Mounting Hole Pattern for .062
[1.57] Thk. PC Board
Note: Consult Product Drawing for details
on placing headers onto PC boards.
Base Part Numbers
Straight Posts Right-Angle Posts
Without With Without With
Retentive Legs Retentive Legs Retentive Legs Retentive Legs
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
644456 32–58 644695 32–58 644457 32–58 644694 32–58
Standard UL94V-0, .000030 [0.00076] Gold Plated
644884 2–28 644886 2–28 644885 2–28 644887 2–28
Standard UL94V-0, .000015 [0.00038] Gold Plated
644888 2–28 644890 2–28 644889 2–28 644891 2–28
High temperature product available. Please contact Sales Engineer or Product Information Center.
.125
[3.18]
A
.025
[0.64]
Sq.
.100
[2.54]
Typ.
.050
[1.27]
Typ.
Post No. 1
.295
[7.49]
.100
[2.54]
.535
[13.59]
.290
[7.37]
.035
[0.89]
Min.
.140
[3.56]
Ref.
.225
[5.72]
.125
[3.18]
A
.025
[0.64]
Sq.
.100
[2.54]
Typ.
.050
[1.27]
Typ.
Post
No. 1
.295
[7.49]
.290
[7.37]
.100
[2.54]
.140
[3.56]
.140
[3.56]
Max.
.035
[0.89]
Min.
.225
[5.72]
.100
[2.54]
Typ.
Edge of Board
.130
[3.30]
Min.
.050/.040
[1.27/1.02]
Dia. for straight leg headers
Dia. for retentive leg headers
.037
[0.94 ]
± .002 ± 0.05
.100
[2.54]
Typ.
Edge of Board
X
.050/.040
[1.27/1.02]
Dia. for straight  leg headers
Dia. for retentive leg headers
.037
[0.94 ]
± .002 ± 0.05
.125
[3.18]
Ref.
34°
.135
[3.43]
Ref.
34°
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Polarized Headers—Straight and Right-Angle
Material and Finish
Straight Post (.025 [0.64] Square)
Right-Angle Post (.025 [0.64] Square)
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
3. All posts on retentive leg headers
are bent.
4. To determine header overall
length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be:
Base number 641213 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-641213-0
All part numbers are the RoHS equivalent version. Example:
No. of
Pos.
2 3-641213-2
28 5-641213-8
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Lead Free
Prefix/Suffix
RoHS
Recommended Mounting Hole Pattern
for .062 [1.57] Thk. PC Board
thru
Base Part Numbers
Straight Posts Right-Angle Posts
Without With Without With
Retentive Legs Retentive Legs Retentive Legs Retentive Legs
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
640454 2–28 644876 2–28 640455 2–28 644877 2–28
Standard UL94V-0, .000030 [0.00076] Gold Plated
641213 32–58 —— 641214 32–58 ——
Standard UL94V-0, .000015 [0.00038] Gold Plated
641124 32–58 —— 641125 32–58 ——
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Retentive Leg
X = .110 [2.79] min., .160 [4.06]
X = .110 [2.79] min., .120 [3.05]
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
Note: Consult Product Drawing for details
on placing headers onto PC boards.
max. when mated with MTA-100 Connector.
max. when mated with CST-100 II Connector.
Retentive Leg
23
MTA-100
.100 [2.54]
.050
[1.27]
Typ.
Post
No. 1
.295
[7.49]
.100
[2.54]
.140
[3.56]
Ref.
.535
[13.59]
.310
[7.87]
.125
[3.18]
A
.100
[2.54]
Typ.
.040
[1.02]
Max.
.025
[0.64]
Sq.
.225
[5.72]
.125
[3.18]
A
.025
[0.64]
Sq.
.100
[2.54]
Typ.
.050
[1.27]
Typ.
.295
[7.49]
.310
[7.87]
.100
[2.54]
.140
[3.56]
Max.
.140
[3.56]
.040
[1.02]
Max.
.225
[5.72]
Post
No. 1
.125
[3.18]
Ref.
34°
.135
[3.43]
34°
.100
[2.54]
Typ.
Edge of Board
.130
[3.30]
Min.
.050/.040
[1.27/1.02]
Dia. for straight leg headers
Dia. for retentive leg headers
.037
[0.94 ]
± .002 ± 0.05
.100
[2.54]
Typ.
Edge of Board
X
.050/.040
[1.27/1.02]
Dia. for straight  leg headers
Dia. for retentive leg headers
.037
[0.94 ]
± .002 ± 0.05
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Friction Lock Headers—Straight and Right-Angle
MTA-100
.100 [2.54]
24
Material and Finish
Straight Post (.025 [0.64] Square)
Right-Angle Post (.025 [0.64] Square)
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
3. All posts on retentive leg headers
are bent.
4. To determine header overall
length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be:
Base number 641215 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-641215-0
All part numbers are the RoHS equivalent version. Example:
No. of Standard
Pos. Prefix/Suffix
2 641215-2 3-641215-2
28 2-641215-8 5-641215-8
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Lead Free
Prefix/Suffix
thru
RoHS
Recommended Mounting Hole Pattern
for .062 [1.57] Thk. PC Board
Base Part Numbers
Straight Posts Right-Angle Posts
Without With Without With
Retentive Legs Retentive Legs Retentive Legs Retentive Legs
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
640456 2–28 644874 2–28 640457 2–28 644875 2–28
Standard UL94V-0, .000030 [0.00076] Gold Plated
641215 32–58 —— 641216 32–58 ——
Standard UL94V-0, .000015 [0.00038] Gold Plated
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
641126 32–58 —— 641127 32–58 ——
Retentive Leg Retentive Leg
X = .110 [2.79] min., .160 [4.06]
max. when mated with MTA-100 Connector.
X = .110 [2.79] min., .120 [3.05]
max. when mated with
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
CST-100 II Connector.
Note: Consult Product Drawing for details on placing headers onto PC boards.
.070
[1.78]
Min.
Ø .052
± .002
[1.32
± 0.05
]
.100
[2.54]
.090
[2.29]
Ø .040
± .003
[1.02
± 0.07 ]
Typ.
.025
± .001
[0.64
± 0.03
]
Square Typ.
.113
[2.87]
A
.250
[6.35]
.025-.040
[0.64-1.01]
.070
[1.78]
.135
[3.43]
.290
± .010
[7.37
± 0.25
]
.347
± .010
[8.81
± 0.25
]
.550
± .010
[13.97
± 0.25
]
.125
[3.18]
.050
[1.27]
.100
[2.54]
Typ.
Post No. 1
.025
± .001
[0.64
± 0.03
]
Square Typ.
.113
[2.87]
A
.250
[6.35]
.055
[1.39]
.055
[1.40]
.070
[1.78]
.135
[3.43]
.290
± .010
[7.37
± 0.25
]
.347
± .010
[8.81
± 0.25
]
.550
± .010
[13.97
± 0.25
]
.125
[3.18]
.050
[1.27]
Typ.
.100
[2.54]
Post No. 1
Min.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Page_Head (Continued)
MTA-100 Headers with Retention Peg—Straight
Material and Finish
Friction Lock
Housing — UL94V-0 rated, thermo-
plastic, black Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
3. To determine header overall
length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
For mateability options, see matrix on pages 12 and 13.
Polarized
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be:
Base number 647609 plus
prefix-and-suffix
4- -0
The correct ordering number is
All part numbers are the RoHS equivalent version. Example:
No. of Standard
Pos. Prefix/Suffix
Note: All RoHS equivalent par t num-
bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
4-647609-0
Lead Free
RoHS
Prefix/Suffix
2 647609-2 3-647609-2 3 647609-3 3-647609-3 4 647609-4 3-647609-4 5 647609-5 3-647609-5 6 647609-6 3-647609-6 7 647609-7 3-647609-7 8 647609-8 3-647609-8
9 647609-9 3-647609-9 10 1-647609-0 4-647609-0 11 1-647609-1 4-647609-1 12 1-647609-2 4-647609-2
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Friction Lock Polarized
Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647609 32-42 647623 32-42
Standard UL94V-0, .000030 [0.00076] Gold Plated
647626 32-42 647624 32-42
Standard UL94V-0, .000015 [0.00038] Gold Plated
647627 32-42 647625 32-42
Recommended Mounting Hole Pattern
for .062 [1.57] Thk. PC Board
Note: Consult Product Drawing
for details on placing headers onto PC boards.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
25
MTA-100
.100 [2.54]
.250
[6.35]
.113
[2.87]
A
.025
[0.64]
Sq.
.050
[1.27]
.100
[2.54]
.347
[8.81]
.290
[7.37]
.112
[2.84]
.040
[1.02]
Max.
.125
[3.18]
Post No. 1
.113
[2.87]
.025
[0.64]
Sq.
.100
[2.54]
.050
[1.27]
Post No. 1
.290
[7.37]
.125
[3.18]
.070
[1.78]
.112
[2.84]
.250
[6.35]
.347
[8.81]
.140
[3.56]
A
.100
[2.54]
Typ.
.040
± .003
[1.02
± 0.07
]
Dia.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 High Profile Headers—Right-Angle
MTA-100
.100 [2.54]
Material and Finish
Housing — UL94V-0 rated, thermo-
plastic, black
Friction Lock
Right-Angle Post (.025 [0.64] Square)
Polarized
Right-Angle Post (.025 [0.64] Square)
Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail.
3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
4. This product can be mounted in the middle of the PC Board as shown in the PCB layout.
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with right-angle posts would be:
Base number 647630 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-647630-0
Recommended Mounting Hole Pattern
for .062 [1.57] Thk. PC Board
All part numbers are the RoHS equivalent version. Example:
Lead Free
RoHS
Prefix/Suffix
Base Part Numbers
Friction Lock Polarized
Right-Angle Posts Right-Angle Posts
Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647630 32-42 647651 32-42
Standard UL94V-0, .000030 [0.00076] Gold Plated
647629 32-42 647653 32-42
Standard UL94V-0, .000015 [0.00038] Gold Plated
647628 32-42 647652 32-42
No. of
Pos.
2 3-647630-2 3 3-647630-3 4 3-647630-4 5 3-647630-5 6 3-647630-6 7 3-647630-7 8 3-647630-8
9 3-647630-9 10 4-647630-0 11 4-647630-1 12 4-647630-2
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
26
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Note: Consult Product Drawing for details on placing headers onto PC boards.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
.113
[2.87]
A
.025
[0.64]
Sq.
.100
[2.54]
.050
[1.27]
Post
No. 1
.290
[7.37]
.135
[3.43]
.550
[13.97]
.070
[1.78]
.125
[3.18]
.250
[6.35]
.347
[8.81]
.113
[2.87]
.025
[0.64]
Sq.
.100
[2.54]
.050
[1.27]
Post No. 1
.290
[7.37]
.125
[3.18]
.070
[1.78]
.112
[2.84]
.250
[6.35]
.347
[8.81]
.140
[3.56]
A
.300
[7.62]
.150
[3.81]
.100
[2.54]
Typ.
.040
[1.02]
Pre-Tinned Plated
Thru Hole Typ.
.060
[1.52]
Pre-Tinned Land
Both Sides Typ.
.008
[0.20]
Min. Thk. Solder
Paste In Area Shown
.065
[1.65]
.0325
[0.826]
Post No. 1
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Page_Head (Continued)
MTA-100 Polarized High Temperature Headers—Straight and Right-Angle
Material and Finish
Housing
2–12 Position — UL94V-0 rated, nylon, black
For use with Infrared Reflow Process Maximum Temperature Rating: 2–12 Position: 280°C
13–18 Position: 235°C
Straight Post (.025 [0.64] Square)
Right-Angle Post (.025 [0.64] Square)
13–18 Position — UL94V-0 rated, LCP, black
Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail.
3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be:
Base number 647047 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-647047-0
All part numbers are the RoHS equivalent version. Example:
Lead Free
RoHS
Prefix/Suffix
thru
thru
Recommended Mounting Hole Pattern for .062 [1.57] Thick PC Board
Base Part Numbers
Straight Posts Straight Posts (Tube Loaded) Right-Angle Posts
Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647047 32–42 647298 32–42 647048 32–42
Standard UL94V-0, .000030 [0.00076] Gold Plated
647109 32–42 647300 32–42 647114 32–42
Standard UL94V-0, .000015 [0.00038] Gold Plated
647075 32–42 647299 32–42 647076 32–42
Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or
product manager for details.
No. of
Pos.
2 3-647047-2
12 4-647047-2 13 NA
18 NA
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Note: Consult Product Drawing for details on placing headers onto PC boards.
27
MTA-100
.100 [2.54]
.300
[7.62]
.150
[3.81]
.100
[2.54]
Typ.
.040
[1.02]
Pre-Tinned Plated
Thru Hole Typ.
.060
[1.52]
Pre-Tinned Land
Both Sides Typ.
.008
[0.20]
Min. Thk. Solder
Paste In Area Shown
.065
[1.65]
.0325
[0.826]
Post No. 1
.250
[6.35]
.113
[2.87]
A
.025
[0.64]
Sq.
.050
[1.27]
.100
[2.54]
.130
[3.30]
.550
[13.97]
.347
[8.81]
.290
[7.37]
.040
[1.02]
Max.
.125
[3.18]
Post No. 1
.250
[6.35]
.113
[2.87]
A
.025
[0.64]
Sq.
.050
[1.27]
.100
[2.54]
.347
[8.81]
.290
[7.37]
.112
[2.84]
.040
[1.02]
Max.
.125
[3.18]
Post No. 1
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Friction Lock High Temperature Headers—Straight and Right-Angle
MTA-100
.100 [2.54]
28
Material and Finish
Housing
2–12 Position — UL94V-0 rated, nylon, black
For use with Infrared Reflow Process Maximum Temperature Rating: 2–12 Position: 280°C
13–18 Position: 235°C
Straight Post (.025 [0.64] Square)
Right-Angle Post (.025 [0.64] Square)
13–18 Position — UL94V-0 rated, LCP, black
Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail.
3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be:
Base number 647050 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-647050-0
All part numbers are the RoHS equivalent version. Example:
thru
thru
Lead Free
Prefix/Suffix
RoHS
No. of Standard
Pos. Prefix/Suffix
2 647050-2 3-647050-2
12 1-647050-2 4-647050-2 13 1-647050-3 NA
18 1-647050-8 NA
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Base Part Numbers
Straight Posts Straight Posts (Tube Loaded) Right-Angle Posts
Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647050 32-42 647295 32-42 647051 32-42
Standard UL94V-0, .000030 [0.00076] Gold Plated
647116 32-42 647297 32-42 647117 32-42
Standard UL94V-0, .000015 [0.00038] Gold Plated
647078 32-42 647296 32-42 647079 32-42
Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or
product manager for details.
Recommended Mounting Hole Pattern for .062 [1.57] Thick PC Board
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Note: Consult Product Drawing for details on placing headers onto PC boards.
.250
[6.35]
.318
[8.08]
Ref.
.113
[2.87]
.025
[0.64]
Sq.
.050
[1.27]
.100
[2.54]
.347
[8.81]
.290
[7.37]
.070
[1.78]
.125
[3.18]
.159
[4.04]
Typ.
Post No. 1
.250
[6.35]
.318
[8.08]
Ref.
.113
[2.87]
.025
[0.64]
Sq.
.050
[1.27]
.100
[2.54]
.347
[8.81]
.290
[7.37]
.040
[1.02]
Max.
.125
[3.18]
.159
[4.04]
Post No. 1
.235
[5.97]
.100
[2.54]
Typ.
.060
[1.52]
.070
[1.78]
Post No. 1
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Polarized and Friction Lock Surface Mount Headers—Straight
Material and Finish
Housing
2–12 Position — UL94V-0 rated, nylon, black
For use with Infrared Reflow Process Maximum Temperature Rating: 2–12 Position: 280°C
13–18 Position: 235°C
Polarized Header
Friction Lock Header
13–18 Position — UL94V-0 rated, LCP, black
Posts — Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail.
3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm].
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14, 15 and 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position sur­face mount polarized header would be:
Base number 647106 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-647106-0
All part numbers are the RoHS equivalent version. Example:
Lead Free
RoHS
Prefix/Suffix
No. of
Pos.
2 3-647106-2
12 4-647106-2
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Polarized Headers Friction Lock Headers
Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647106 32-42 647166 32-42
Standard UL94V-0, .000030 [0.00076] Gold Plated
647108 32-42 647168 32-42
Standard UL94V-0, .000015 [0.00038] Gold Plated
647107 32-42 647167 32-42
Tape Mount Part Numbers
Polarized Headers Friction Lock Headers
Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647531 32-42 647502 32-42
Standard UL94V-0, .000030 [0.00076] Gold Plated
Standard UL94V-0, .000015 [0.00038] Gold Plated
Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or
product manager for details.
Recommended PC Board Layout for use with .010 [0.25] Thick Stencil
1744163 32-42
647467 32-42
Note: Consult Product Drawing for details on placing headers onto PC boards.
29
MTA-100
.100 [2.54]
A
.025
[0.64]
Typ.
.100
[2.54]
.092
[2.34]
Typ. Ref.
Post No. 1
.313
[7.95]
.410
[10.41]
.140
[3.56]
.176
[4.47]
Ref.
.107
[2.72]
Ref.
.125
[3.18]
.200
[5.08]
.440
[11.18]
.042
[1.07]
.100
[2.54]
Typ.
.081/.075
[2.06/1.91]
.124
[3.15]
Edge of Board
.125
[3.18]
Min.
.050/.040
[1.27/1.02]
Dia.
Dia.
A
.025
[0.64]
Typ.
.100
[2.54]
.092
[2.34]
Typ. Ref.
Post No. 1
.313
[7.95]
.410
[10.41]
.176
[4.47]
Ref.
.130
[3.30]
.200
[5.08]
.050
[1.27]
Max.
.137
[3.48]
Ref.
.100
[2.54]
Typ.
Edge of Board
.300
[7.62]
Max.
.050/.040
[1.27/1.02]
Dia.
.206
[5.23]
Ref.
.130
[3.30]
Ref.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-100 Shrouded Headers—Straight and Right-Angle
MTA-100
.100 [2.54]
Material and Finish
Housing — UL94V-0 rated, polyester,
black Posts — Copper alloy, tin plated; or
.000030 [0.00076] gold over nickel
Notes:
1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Headers with .000015 [0.00038] gold plated post are available upon request. Minimums may apply.
3. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail.
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 14 and 15.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts and with pegs would be:
Base number 644486 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-644486-0
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num-
bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Notes:
1. Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
2. MTA-100 shrouded headers do not mate with CST-100 II hous­ings.
Straight Post (.025 [0.64] Square)
Right-Angle (.025 [0.64] Square)
Front Bend
Polarized
Retention Peg
Rear Bend
Note: Consult Product Drawing
for details on placing headers onto PC boards.
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
(Solder Side of Board Shown)
Recommended Mounting Hole Pattern for .062
[1.57] Thk. PC Board
(Solder Side of Board Shown)
Base Part Numbers
Straight Posts Right-Angle Posts
With Without Pegs Pegs
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Front Bend Rear Bend
Standard UL94V-0, Tin Plated
644486 22-34 644861 22-34 644488 22-34 644803 22-34
Standard UL94V-0, .000030 [0.00076] Gold Plated
644487 22-34 —— 644489 22-34 ——
Without Pegs Only
30
Header Length
No. of Dim. Prefix/
Circuits A Suffix
.284
7.21
.384
9.75
.484
12.29
.584
14.83
3- -2
3- -3
3- -4
3- -5
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
2
3
4
5
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
No. of Dim. Prefix/
Circuits A Suffix
.684
17.37
.784
19.91
.884
22.45
.984
24.99
6
7
8
9
3- -6
3- -7
3- -8
3- -9
No. of Dim. Prefix/
Circuits A Suffix
10
11
12
13
1.084
27.53
1.184
30.07
1.284
32.61
1.384
35.15
4- -0
4- -1
4- -2
4- -3
No. of Dim. Prefix/
Circuits A Suffix
14
1.484
37.69
4- -4
®
.260
[6.60]
Ref.
.510
[12.95]
.190
[4.83]
A
.100
[2.54]
Typ.
.060
[1.52]
Typ.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
.100 [2.54] Centerline CST-100 II Crimp Contacts and Housings
Product Facts
Low cost wire-to-board
interconnections
Wide wire range for single
contact
Tin and gold plated
contacts
Mates with specified MTA
and similar competitive notched headers
Plastic latching feature in
housing helps prevent con­tact backout
Locking ramps and polariz-
Application Tooling
Loose Piece Contacts
Hand Tool No. 58517-3 (408-4064) Strip Contacts — AMP-O-LECTRIC Model “G”
Termination Machine* Applicator No. 567373-3 (Request Catalog 65828)
AMP-O-MATIC Stripper-Crimper Machine* Applicator No. 567910-1 or 567827-1 (with CQM) (Request Catalog
65004) AMPOMATOR CLS IIIG Lead Making
Machine* (Request Catalog 82659) *Requires applicators. For part
numbers, call Technical Support.
ing tabs are standard
For keying purposes use
keying plug 641994-1 (page 17)
Recognized under the
Component Program of Underwriters Laboratories Inc., File No. E28476
Certified by Canadian
Standards Association, File No. LR7189
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see pages 21 thru 29 and 32.
See page 15 for an explanation of RoHS lead free equivalents.
Performance Data
Voltage Rating —250 vac Current Rating — 4 amp max. Low-Level Resistance — 6 m
max. initial; 10 mmax. final Insulation Resistance — 1000 M
min. initial; 100 Mmin. final Operating Temperature
55C to 105C
Technical Documents
Product Specification
108-1948
Application Specification
114-13036
Instruction Sheet
408-8493
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Contacts
Part Numbers
Tin Plated 15 Au Gold Plated 30 Au Gold Plated
1375819-1 (Strip) 1375819-2 (Strip) 1375819-3 (Strip) 1445336-1 (Loose Piece) 1445336-2 (Loose Piece) 1445336-3 (Loose Piece)
Material and Finish (RoHS Compliant)
Phosphor bronze, pretinned or .000015 [.00038] gold, over nickel .000030 [0.00076] gold over nickel
Wire Range — 22–26 AWG [0.35–0.13 mm2] Max. Ins. Dia. — .065 [1.65]
Housing*
Material (RoHS Compliant)
UL94V-0 rated, nylon, white
No. of Dim. Part
Pos. A Numbers
.220
2
5.59
.320
3
8.13
.420
4
10.67
.520
5
13.21
.620
6
15.75
.720
7
18.29
.820
8
20.83
.920
9
23.37
1.020
10
25.91
1.120
11
28.45
1.220
12
30.99
1.320
13
33.53
1.420
14
36.07
1.520
15
38.61
1375820-2
1375820-3
1375820-4
1375820-5
1375820-6
1375820-7
1375820-8
1375820-9
1-1375820-0
1-1375820-1
1-1375820-2
1-1375820-3
1-1375820-4
1-1375820-5
No. of Dim. Part
Pos. A Numbers
1.620
16
17
18
19
20
21
22
23
24
25
26
27
28
41.15
1.720
43.69
1.820
46.23
1.920
48.77
2.020
51.31
2.120
53.85
2.220
56.39
2.320
58.93
2.420
61.47
2.520
64.01
2.620
66.55
2.720
69.09
2.820
71.63
1-1375820-6
1-1375820-7
1-1375820-8
1-1375820-9
2-1375820-0
2-1375820-1
2-1375820-2
2-1375820-3
2-1375820-4
2-1375820-5
2-1375820-6
2-1375820-7
2-1375820-8
.195
[4.95]
.016±.002
[.406±.051]
*Housings without polarizing tabs
may be manufactured upon request. Minimums may apply. Contact product engineering or product manager for details.
.440
[11.17]
31
CST-100 II
.100 [2.54]
A
.025
[0.64]
Typ.
.100
[2.54]
.092
[2.34]
Ref.
Post No. 1
.313
[7.95]
.410
[10.41]
.140
[3.56]
.176
[4.47]
Ref.
.107
[2.72]
Ref.
.125
[3.18]
.280
[7.11]
.520
[13.21]
.042
[1.07]
.100
[2.54]
Typ.
.081/.075
[2.06/1.91]
.124
[3.15]
Edge of Board
.125
[3.18]
Min.
.050/.040
[1.27/1.02]
Dia.
Dia.
A
.025
[0.64]
Typ.
.100
[2.54]
.036
[0.91]
Max.
.092
[2.34]
Typ.
Post No. 1
.313
[7.95]
.176
[4.47]
Ref.
.107
[2.72]
Ref.
.140
[3.56]
.280
[7.11]
.100
[2.54]
Typ.
Edge of Board
.450
[11.43]
Max.
.050/.040
[1.27/1.02]
Dia.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
CST-100 II Shrouded Headers—Straight and Right-Angle
CST-100 II
.100 [2.54]
Material and Finish
Straight Post (.025 [0.64] Square) Right-Angle (.025 [0.64] Square)
Housing — UL94V-0 rated, polyester,
black Posts — Copper alloy, tin plated; or
.000030 [0.00076] gold over nickel
Notes:
1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Headers with .000015 [0.00038] gold plated posts are available upon request. Minimums may apply.
3. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail.
For mateability options, see matrix on pages 12 and 13.
For mating half visuals, see page 31.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of
Polarized
Retention Peg
posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts and with pegs would be:
Base number 644893 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-644893-0
All part numbers are the RoHS equivalent version. Example:
Lead Free
RoHS
Prefix/Suffix
thru
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
No. of
Pos.
2 3-644893-2
14 4-644893-4
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note: CST-100 II shrouded headers only mate with CST-100 II housings. All
the MTA-100 headers except the MTA-100 shrouded headers mate with CST-100 II housings.
32
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
(Solder Side of Board Shown)
Base Part Numbers
Straight Posts
With Without Pegs Pegs
Header
Part Nos.
No. of Posts/
RoHS Equiv. RoHS Equiv.
Part Nos.
Standard UL94V-0, Tin Plated
644893 32-44 644892 32-44 644894 32-44
Standard UL94V-0, .000030 [0.00076] Gold Plated
644897 32-44 644896 32-44 644898 32-44
Header Length
No. of Dim. Prefix/
Circuits A Suffix
.284
7.21
.384
9.75
.484
12.29
3- -2
3- -3
3- -4
2
3
4
Recommended Mounting Hole Pattern for .062
Header
No. of Posts/
No. of Dim. Prefix/
Circuits A Suffix
5
14.83
6
17.37
7
19.91
(Solder Side of Board Shown)
.584
.684
.784
Note: Consult Product Drawing for details
on placing headers onto PC boards.
[1.57] Thk. PC Board
Right-Angle Posts
Without Pegs Only
Header
Part Nos.
3- -5
3- -6
3- -7
No. of Posts/
RoHS Equiv.
No. of Dim. Prefix/
Circuits A Suffix
8
9
10
.884
22.45
.984
24.99
1.084
27.53
3- -8
3- -9
4- -0
Product Facts
R
R
Connectors and headers for
2 through 24 positions; wire sizes of 18, 20, 22, 24 and 26 AWG [0.9– 0.12 mm
Connectors and headers,
except shrouded headers, are end-to-end stackable
Quad Connectors for higher
current rating (page 54)
Posted connectors for 2,3,
4,6,9,12,15 and 24 posi­tions
Card edge connectors for
3, 6, 9,12, 15,18 and 20 through 24 positions
Connectors preloaded with
IDC contacts
All contacts are slotted for
insulation displacement (IDC) termination technique
Connector styles include
both closed end and feed­thru, with and without lock­ing ramps and polarizing tabs
Molded ribs on housing do
not allow reverse mating
Contacts are lubricated for
fretting corrosion protection
Benefits derived from the
MTA-156 system include increases quality and ease of handling such as—
One-step assembly
No wire stripping
No contact damage
Reduced wiring errors
Simpler tooling
Simple maintenance
and repair
Meets the material require-
ments of Table 23.1 of UL 1410 Standards for Television Receiver and Video Products (wire-to­post connectors only)
Recognized under the
Component Program of Underwriters Laboratories Inc., File No. E28476
Certified by Canadian
Standards Association, File No. LR7189
2
]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
.156 [3.96] Centerline MTA-156 IDC Connectors and Headers
MTA-156 connectors accept discrete and ribbon cable wire sizes ranging from 18 – 26 AWG [0.9– 0.12 mm
2
] with maxi­mum insulation outside diameter.095 [2.41] for sin­gle wire and .070 [1.78] for mass termination of wires. Tin plated solid, fused stranded or stranded (7, 16, and 19 strands) wire with PVC insulation can be used on 18 AWG [0.8 – 0.9 mm MTA-156 connectors; 7, 10, and 19 stranded wire on 20 AWG [0.5 – 0.6 mm
2
] MTA-156 connectors; and 7 and 19 stranded wire on 22 – 26 AWG [0.4 – 0.12 mm MTA-156 connectors.
Only one wire to be termi­nated into an IDC contact slot.
Mass termination of wire provides the lowest applied cost because it drastically reduces the labor content of virtually any cable or har­ness assembly required.
The wire-to-post connector housing material is flame retardant thermoplastic, either UL94V-2 or UL94V-0 rated.
A full line of .156 [3.96] centerline headers com­pletes the system. Headers are available with straight or right-angle posts, in flat friction lock and shrouded styles. Headers are available in 2 through 24 positions.
2
]
2
]
Note: Refer to page 70 for approved wire listings.
Performance Data*
Voltage Rating —600 vac Current Rating
7 amp max. for MTA-156 Connector Low-Level Resistance
3.0 mmax. initial Dielectric Withstanding Voltage
2200 vac/1 min. Insulation Resistance
5000 Mmin. initial Operating Temperature
55C to 105C
*Refer to the Product Specification for additional electrical, mechanical and environmental performance tests and requirements.
Technical Documents
Product Specification
108-1051 MTA-156 Connectors
Application Specifications
114-1020 MTA-156 Connectors,
Posted Connectors and Card Edge Connectors
114-1032 MTA-156 Ribbon Cable
Assembly
MTA-156
.156 [3.96]
33
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
MTA-156
.156 [3.96]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
640383
640384
640385
640387
640388
640389
640445
644611
644612
644613
644614
644615
644616
644617
644749
644750
644751
644752
644753
644754
644755
647123
647124
647125
647126
647127
647128
647129
647130
647210
647211
647212
647227
647228
MTA-156 Connector/ Header Mateability Guide
Matrix for Tin Plated Part Numbers
This matrix has been prepared to assist you, our customer, in defin­ing the correct mating halves for the MTA-156 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
Connectors
Headers
640426 YYYNYYYYYYNYYYYYY
640427 YYYNYYYYYYNYYYYYY
640428 YYYNYYYYYYNYYYYYY
640429 YYYNYYYYYYNYYYYYY
640430 YYYNYYYYYYNYYYYYY
640431 YYYYYYYYYYYYYYYYY
640432 YYYYYYYYYYYYYYYYY
640433 YYYYYYYYYYYYYYYYY
640434 YYYYYYYYYYYYYYYYY
640435 YYYYYYYYYYYYYYYYY
640472 YYYNYYYYYYNYYYYYY
640473 YYYNYYYYYYNYYYYYY
640474 YYYNYYYYYYNYYYYYY
640475 YYYNYYYYYYNYYYYYY
640476 YYYNYYYYYYNYYYYYY
640477 YYYYYYYYYYYYYYYYY
640478 YYYYYYYYYYYYYYYYY
640479 YYYYYYYYYYYYYYYYY
640480 YYYYYYYYYYYYYYYYY
640481 YYYYYYYYYYYYYYYYY
640595 YYYNYYYYYYNYYYYYY
640599 YYYNYYYYYYNYYYYYY
640600 YYYNYYYYYYNYYYYYY
640601 YYYNYYYYYYNYYYYYY
640602 YYYNYYYYYYNYYYYYY
640604 YYYYYYYYYYYYYYYYY
640605 YYYYYYYYYYYYYYYYY
640606 YYYYYYYYYYYYYYYYY
640607 YYYYYYYYYYYYYYYYY
640608 YYYYYYYYYYYYYYYYY
641301 YYYNYYYYYYNYYYYYY
641302 YYYNYYYYYYNYYYYYY
641303 YYYNYYYYYYNYYYYYY
641304 YYYNYYYYYYNYYYYYY
641305 YYYNYYYYYYNYYYYYY
641306 YYYYYYYYYYYYYYYYY
641307 YYYYYYYYYYYYYYYYY
641308 YYYYYYYYYYYYYYYYY
641309 YYYYYYYYYYYYYYYYY
641310 YYYYYYYYYYYYYYYYY
643817 YYYNYYYYYYNYYYYYY
643818 YYYNYYYYYYNYYYYYY
643819 YYYNYYYYYYNYYYYYY
643820 YYYNYYYYYYNYYYYYY
643821 YYYNYYYYYYNYYYYYY
644082 YYYYYYYYYYYYYYYYY
644461 YYYYYYYYYYYYYYYYY
644462 YYYYYYYYYYYYYYYYY
644463 YYYYYYYYYYYYYYYYY
644464 YYYYYYYYYYYYYYYYY
644465 YYYNYYYYYYNYYYYYY
644466 YYYNYYYYYYNYYYYYY
644467 YYYNYYYYYYNYYYYYY
644468 YYYNYYYYYYNYYYYYY
644469 YYYYYYYYYYYYYYYYY
644470 YYYYYYYYYYYYYYYYY
644471 YYYYYYYYYYYYYYYYY
644472 YYYYYYYYYYYYYYYYY
644501 YYYYYYYYYYYYYYYYY
644502 YYYYYYYYYYYYYYYYY
644566 YYYYYYYYYYYYYYYYY
644567 YYYYYYYYYYYYYYYYY
644569 YYYYYYYYYYYYYYYYY
644570 YYYYYYYYYYYYYYYYY
644572 YYYYYYYYYYYYYYYYY
644783 YYYNYYYYYYNYYYYYY
644791 YYYYYYYYYYYYYYYYY
644860 YYYNYYYYYYNYYYYYY
644878 YYYNYYYYYYNYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYYYYYYYYYY
YYYNYYYYYYYY
YYYYYYYYYYYY
YYYNYYYYYYYY
YYYNYYYYYYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YNYYYNYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YNYYYNYYY
Y YYYYYYYYY
Y YNYYYNYYY
Y YNYYYNYYY
34
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
647229
647230
647646
647648
1744017
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Connector/Header Mateability Guide (Continued)
This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
Matrix for .000030 [0.00076] Gold Plated Part Numbers
Headers
641202
641203
641204
641207
641208
641209
641210
644627
644628
644629
644630
644631
641217 YYYNYYYYYYNYYYYYY
641218 YYYNYYYYYYNYYYYYY
641219 YYYNYYYYYYNYYYYYY
641220 YYYNYYYYYYNYYYYYY
641221 YYYNYYYYYYNYYYYYY
641222 YYYYYYYYYYYYYYYYY
641223 YYYYYYYYYYYYYYYYY
641224 YYYYYYYYYYYYYYYYY
641225 YYYYYYYYYYYYYYYYY
641226 YYYYYYYYYYYYYYYYY
641227 YYYNYYYYYYNYYYYYY
641228 YYYNYYYYYYNYYYYYY
641229 YYYNYYYYYYNYYYYYY
641230 YYYNYYYYYYNYYYYYY
641231 YYYNYYYYYYNYYYYYY
Connectors
641232 YYYYYYYYYYYYYYYYY
641233 YYYYYYYYYYYYYYYYY
641234 YYYYYYYYYYYYYYYYY
641235 YYYYYYYYYYYYYYYYY
641236 YYYYYYYYYYYYYYYYY
644460 YYYNYYYYYYNYYYYYY
644662 YYYNYYYYYYNYYYYYY
644663 YYYNYYYYYYNYYYYYY
644687 YYYYYYYYYYYYYYYYY
644718 YYYNYYYYYYNYYYYYY
644720 YYYNYYYYYYNYYYYYY
644632
644633
644756
644757
644758
644759
644760
644761
644762
647131
Y YYNYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYYYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
Y YYYYYYYYY
Y YYNYYYYYY
Y YYNYYYYYY
647132
647133
647134
647135
647136
MTA-156
.156 [3.96]
Matrix for .000015
Headers [0.00038] Gold Plated Part Numbers
641113
641114
641115
641118
641148 YYYNYYYYYYYYYNYYYYYYY
641149 YYYNYYYYYYYYYNYYYYYYY
641150 YYYNYYYYYYYYYNYYYYYYY
641151 YYYNYYYYYYYYYNYYYYYYY
641152 YYYNYYYYYYYYYNYYYYYYY
641153 YYYYYYYYYYYYYYYYYYYYY
641154 YYYYYYYYYYYYYYYYYYYYY
641155 YYYYYYYYYYYYYYYYYYYYY
641156 YYYYYYYYYYYYYYYYYYYYY
641157 YYYYYYYYYYYYYYYYYYYYY
641168 YYYNYYYYYYYYYNYYYYYYY
641169 YYYNYYYYYYYYYNYYYYYYY
641170 YYYNYYYYYYYYYNYYYYYYY
641171 YYYNYYYYYYYYYNYYYYYYY
641172 YYYNYYYYYYYYYNYYYYYYY
Connectors
641173 YYYYYYYYYYYYYYYYYYYYY
641174 YYYYYYYYYYYYYYYYYYYYY
641175 YYYYYYYYYYYYYYYYYYYYY
641176 YYYYYYYYYYYYYYYYYYYYY
641177 YYYYYYYYYYYYYYYYYYYYY
644284 YYYNYYYYYYYYYNYYYYYYY
647478 YYYNYYYYYYYYYNYYYYYYY
647479 YYYNYYYYYYYYYNYYYYYYY
647496 YYYYYYYYYYYYYYYYYYYYY
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
641119
641120
644763
641121
644764
644765
644766
644767
644768
644769
647139
647140
647141
647142
647143
647144
647649
35
.725
[18.42]
.245
[6.22]
.100
[2.54]
.325
[8.26]
.355
[9.02]
.230
[5.84]
.156
[3.96]
Typ.
A
.050
[1.27]
.097
[2.46]
.100
[2.54]
.258
[6.56]
.050
[1.27]
.725
[18.42]
.245
[6.22]
.325
[8.26]
.355
[9.02]
.180
[4.57]
.050
[1.27]
.156
[3.96]
Typ.
A
.047
[1.19]
.100
[2.54]
.258
[6.56]
.050
[1.27]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Connectors—Closed End
MTA-156
.156 [3.96]
Material and Finish
Housing — UL94V-2 rated, nylon,
see below for color; or UL94V-0 rated, nylon, black
Contacts — Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [.00038] post gold plated over nickel
Color Coding by Wire Size for UL94V-2 Connectors
26 AWG—Blue 24 AWG—White 22 AWG—Red 20 AWG—Yellow 18 AWG—Orange
All Wire Sizes in UL94V-0
Black
Notes:
1. Only connectors with locking
ramp and without polarizing tabs mate with posted connectors on page 45.
2. Refer to pages 70 thru 74 for
approved wire listing.
3. For strain reliefs and dust covers,
see pages 40 and 41.
4. For keying plugs and panel
mount end caps, see page 42.
5. Other circuit sizes are available
upon request. Minimums may apply.
6. Connector circuits can be
molded closed for keying pur­poses. Minimums may apply.
7. Where no part numbers appear
in the chart, parts can be made available upon request. Minimums may apply.
8. To determine connector overall
length (Dim. A), multiply .156 x the number of circuits. Example: .156 x 10 circuits equals 1.560 inches [39.62 mm].
Closed End with Locking Ramp
without Polarizing Tabs
with Polarizing Tabs
For mateability options, see matrix on pages 34 and 35.
Mating half visuals for Closed End Connectors with Locking Ramp, see pages 45 thru 48, 50, 52, and 53, (49 and 51 Front Bend Headers Only).
Closed End without Locking Ramp
without Polarizing Tabs
with Polarizing Tabs
36
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
For mateability options, see matrix on pages 34 and 35.
Mating half visuals for Closed End Connectors without Locking Ramp, see pages 46 thru 53.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Connectors—Closed End (Continued)
Connector Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described connec­tors.
Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 10-position closed end con­nector with locking ramp and without polarizing tabs for 18 AWG wire would be:
Base number 640426 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-640426-0
All part numbers in bold face are the RoHS equivalent version. Example:
No. of
Pos.
2 3-640426-2 3 3-640426-3 4 3-640426-4 5 3-640426-5 6 3-640426-6 7 3-640426-7 8 3-640426-8
9 3-640426-9 10 4-640426-0 11 4-640426-1 12 4-640426-2 13 4-640426-3 14 4-640426-4 15 4-640426-5 16 4-640426-6 17 4-640426-7 18 4-640426-8 19 4-640426-9 20 5-640426-0 21 5-640426-1 22 5-640426-2 23 5-640426-3 24 5-640426-4
Note: All RoHS equivalent part num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Lead Free
RoHS
Prefix/Suffix
Base Part Numbers
Closed End with Locking Ramp Closed End without Locking Ramp
Connector Type
& Wire Size
Standard UL94V-2, Tin Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Tape Mounted on Reel UL94V-2, Tin Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Standard UL94V-2, .000030 [0.00076] Gold Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Standard UL94V-2, .000015 [0.00038] Gold Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Standard UL94V-0, Tin Plated (Black in color)
18 AWG
0.8–0.9 mm
22 AWG
0.3–0.4 mm
1
Other circuit sizes are available upon request. Minimums may apply.
2
2
Note: Blocked circuit configurations are available upon request. Contact product engineer or product manager for details. Minimums may apply.
Without Tabs With Tabs Without Tabs With Tabs
Connector Connector Connector Connector
Part RoHS Part RoHS Part RoHS Part RoHS
Nos. Equiv. Nos. Equiv. Nos. Equiv. Nos. Equiv.
1
640426 32–54 643817 32–54 640431 32–54 644461
32–44
640427 32–54 643818 32–54 640432 32–54 644462132–44
640428 32–54 643819 32–54 640433 32–54 644463132–44
640429 32–54 643820 32–54 640434 32–54 644464132–44
640430 32–54 643821 32–54 640435 32–54 ——
640472 32–54 644878 32–54 640477 32–54 ——
640473 32–54 ——640478 32–54 ——
640474 32–54 644783 32–54 640479 32–54 644791132–44
640475 32–54 ——640480 32–54 ——
640476 32–54 ——640481 32–54 ——
1
641217 32–54 644460
32–42 641222 32–54 ——
641218 32–54 644663132–42 641223 32–54 ——
641219 32–54 644662132–42 641224 32–54 644687132–44
641220 32–54 ——641225 32–54 ——
641221 32–54 ——641226 32–54 ——
1
641148 32–54 644284
32–42 641153 32–54 ——
641149 32–54 ——641154 32–54 ——
641150 32–54 647478132–42 641155 32–54 ——
641151 32–54 ——641156 32–54 ——
641152 32–54 ——641157 32–54 ——
1
644860
32–42 ——644502132–42 644082132–42
————644501132–42 644566132–42
MTA-156
.156 [3.96]
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
37
.725
[18.42]
.245
[6.22]
.325
[8.26]
.385
[9.78]
.180
[4.57]
.156
[3.96]
Typ.
A
.050
[1.27]
.047
[1.19]
.258
[6.56]
.050
[1.27]
.100
[2.54]
.725
[18.42]
.245
[6.22]
.100
[2.54]
.325
[8.26]
.385
[9.78]
.230
[5.84]
.156
[3.96]
Typ.
A
.050
[1.27]
.097
[2.46]
.100
[2.54]
.258
[6.56]
.050
[1.27]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Connectors—Feed-Thru
MTA-156
.156 [3.96]
Material and Finish
Housing — UL94V-2 rated, nylon,
see below for color; or UL94V-0 rated, nylon, black
Contacts — Phosphor bronze; post tin plated, .000030 [.00076] or .000015 [.00038] post gold plated over nickel
Color Coding by Wire Size for UL94V-2 Connectors
26 AWG—Blue 24 AWG—White 22 AWG—Red 20 AWG—Yellow 18 AWG—Orange
All Wire Sizes in UL94V-0
Black
Notes:
1. Only connectors with locking ramp and without polarizing tabs mate with posted connectors on page 45.
2. Refer to pages 70 thru 74 for approved wire listing.
3. For strain reliefs and dust covers, see pages 40 and 41.
4. For keying plugs and panel
mount end caps, see page 42.
5. Other circuit sizes are available
upon request. Minimums may apply.
6. Connector circuits can be
molded closed for keying pur­poses. Minimums may apply.
7. Where no part numbers appear
in the chart, parts can be made available upon request. Minimums may apply.
8. To determine connector overall
length (Dim. A), multiply .156 x the number of circuits. Example: .156 x 10 circuits equals 1.560 inches [39.62 mm].
Feed-Thru with Locking Ramp
without Polarizing Tabs
with Polarizing Tabs
For mateability options, see matrix on pages 34 and 35.
Mating half visuals for Feed–Thru Connectors with Locking Ramp, see pages 45 thru 48, 50, 52, and 53, (49 and 51 Front Bend Headers Only).
Feed-Thru without Locking Ramp
without Polarizing Tabs
38
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
For mateability options, see matrix on pages 34 and 35.
Mating half visuals for Feed–Thru Connectors without Locking Ramp, see pages 46 thru 53.
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
with Polarizing Tabs
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Connectors—Feed-Thru (Continued)
Connector Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and num­ber of circuits available for the described connectors.
Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 10-position feed-thru con­nector with locking ramp and without polarizing tabs for 18 AWG wire would be:
Base number 640599 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-640599-0
The part numbers in bold face are the RoHS equiva-
lent version. Example:
No. of
Pos.
2 3-640599-2 3 3-640599-3 4 3-640599-4 5 3-640599-5 6 3-640599-6 7 3-640599-7 8 3-640599-8
9 3-640599-9 10 4-640599-0 11 4-640599-1 12 4-640599-2 13 4-640599-3 14 4-640599-4 15 4-640599-5 16 4-640599-6 17 4-640599-7 18 4-640599-8 19 4-640599-9 20 5-640599-0 21 5-640599-1 22 5-640599-2 23 5-640599-3 24 5-640599-4
Note: All RoHS equivalent part num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Lead Free
RoHS
Prefix/Suffix
Base Part Numbers
Feed-Thru with Locking Ramp Feed-Thru without Locking Ramp
Connector Type
& Wire Size
Standard UL94V-2, Tin Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Tape Mounted on Reel UL94V-2, Tin Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Standard UL94V-2, .00003 [.00076] Gold Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Standard UL94V-2, .000015 [.00038] Gold Plated
18 AWG
0.8–0.9 mm
20 AWG
0.5–0.6 mm
22 AWG
0.3–0.4 mm
24 AWG
0.2 mm
26 AWG
0.12–0.15 mm
2
2
2
2
2
Standard UL94V-0, Tin Plated
18 AWG
0.8–0.9 mm
22 AWG
0.3–0.4 mm
1
Other circuit sizes are available upon request. Minimums may apply.
2
2
Note: Blocked circuit configurations are available upon request. Contact product engineer or product manager for details. Minimums may apply.
Without Tabs With Tabs Without Tabs With Tabs
Connector Connector Connector Connector
Part RoHS Part RoHS Part RoHS Part RoHS
Nos. Equiv. Nos. Equiv. Nos. Equiv. Nos. Equiv.
1
640599 32–54 644465
32–44 640604 32–54 644469132–44
640600 32–54 644466132–44 640605 32–54 644470132–44
640601 32–54 644467132–44 640606 32–54 644471132–44
640602 32–54 644468132–44 640607 32–54 644472132–44
640595 32–54 ——640608 32–54 ——
641302 32–54 ——641306 32–54 ——
641303 32–54 ——641307 32–54 ——
641304 32–54 ——641308 32–54 ——
641305 32–54 ——641309 32–54 ——
641301 32–54 ——641310 32–54 ——
1
641227 32–54 644718
32–44 641232 32–54 ——
641228 32–54 ——641233 32–54 ——
641229 32–54 644720132–44 641234 32–54 ——
641230 32–54 ——641235 32–54 ——
641231 32–54 ——641236 32–54 ——
1
641168 32–54 647479
32–42 641173 32–54 ——
641169 32–54 ——641174 32–54 ——
641170 32–54 647496132–42 641175 32–54 ——
641171 32–54 ——641176 32–54 ——
641172 32–54 ——641177 32–54 ——
1
————644567
32–42 644570132–42
————644569132–42 644572132–42
MTA-156
.156 [3.96]
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
39
A
.130
[3.30]
.105
[2.67]
.440
[11.18]
.335
[8.51]
Retention Dimple
.127
[3.23]
.440
[11.18]
Note: This portion of front locking bar  may or may not be present
A
.335
[8.51]
.127
[3.23]
.470
[11.94]
Note: This portion of front locking bar  may or may not be present
A
A
.325
[8.26]
.475
[12.07]
.130
[3.3]
Retention Dimple
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Connector Accessories
MTA-156
.156 [3.96]
Closed End Covers
Material (RoHS Compliant)
Strain Relief Covers — UL94V-2
rated, nylon, white Dust Covers — UL94V-0 rated,
polyester, white
Feed-Thru Covers
Material (RoHS Compliant)
Strain Relief Covers — UL94V-2
rated, nylon, white Dust Covers — UL94V-0 rated,
polyester, white
Strain Relief Covers Dust Covers
Base Part Numbers
Strain Relief Dust
Covers Covers
Cover No. of Cover No. of
Part Nos. Circuits Part Nos. Circuits
643067 2–24 640551 2–24
Strain Relief Covers
Dust Covers
Closed End
Base Part Numbers
Feed-Thru
Strain Relief Dust
Covers Covers
Cover No. of Cover No. of
Part Nos. Circuits Part Nos. Circuits
Cover Ordering Information
643071 2–24 640643 2–24
The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described cover.
Prefixes and suffixes are determined by the number of circuit positions in the cover. For example, the complete part number for a 10-position closed-end strain relief cover would be:
Base number 643067 plus
prefix-and-suffix
The correct ordering number is
40
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
1- -0
1-643067-0
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Cover Length
No. of Dim. Prefix/
Circuits A Suffix
2
3
4
5
6
7
8
9
.312
7.92
.468
11.89
.624
15.85
.780
19.81
.936
23.77
1.092
27.74
1.248
31.7
1.404
35.66
No. of Dim. Prefix/
Circuits A Suffix
-2
-3
-4
-5
-6
-7
-8
-9
10
11
12
13
14
15
16
17
1.560
39.62
1.716
43.59
1.872
47.55
2.028
51.51
2.184
55.47
2.340
59.44
2.496
63.4
2.652
67.36
1- -0
1- -1
1- -2
1- -3
1- -4
1- -5
1- -6
1- -7
No. of Dim. Prefix/
Circuits A Suffix
18
19
20
21
22
23
24
2.808
71.32
2.964
75.29
3.120
79.25
3.276
83.21
3.432
87.17
3.588
91.14
3.744
95.1
1- -8
1- -9
2- -0
2- -1
2- -2
2- -3
2- -4
.110
[2.79]
.105
[2.67]
.580
[14.73]
.165
[4.19]
Max.
Replacement IDC Contacts
.637
[16.18]
.125
[3.18]
Material and Finish
Contacts — Phosphor bronze, post tin
plated; .000030 [0.00076] or .000015 [0.00038] post gold plated over nickel
Note: Tyco Electronics does not rec-
ommend terminating an MTA contact more than one time. Use replacement contacts when required for field repairs or wire changes.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Connector Accessories (Continued)
Wire Size
AWG mm
18 0.8–0.9 640631-3 641143-4 641143-3 20 0.5–0.6 640632–3 641144-4 641144-3 22 0.3–0.4 640633-3 641145-4 641145-3 24 0.2 640634-3 641146-4 641146-3 26 0.12–0.15 640635-3 641147-4 641147-3
2
Tin Plated .000030 [0.00076] .000015 [0.00038]
Part Numbers
Gold Plated Gold Plated
MTA-156
.156 [3.96]
Crimp Snap-in Contacts
Material and Finish
Contacts — Phosphor bronze,
tin plated
Wire Size Part Nos.
AWG mm2Loose Piece* Strip**
26–22 .12–0.3 640557-3 640556-3 22–18 0.3–0.9 640559-3 640558-3
**Hand Tool No. 59837-1 (408-6528)
**AMP-O-LECTRIC Model “G” Termination Machine (Request Catalog 65828) Note: Requires applicator. For part number, call Technical Support.
Special applications for crimp snap-in contacts are:
1. Double wire per contact
2. Coax or shielded wire
3. Mixed wire size in same connector
Note: Only one crimp snap-in contact per connector.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
41
.375
[9.52]
.300
[7.62]
.065
[1.65]
.051
[1.30]
.066
[1.68]
.070
[1.78]
Dia.
.300
[7.62]
.085
[2.16]
.065
[1.65]
.051
[1.30]
.066
[1.68]
.453
[11.5]
.578
[14.7]
.010
[.254]
Max. R. Typ. at Min.
Tolerance Cutout
.125
[3.18]
.500
[12.70]
Ref.
2.525
[64.14]
Ref.
.300
[7.62]
Ref.
.440
[11.18]
.520
[13.2]
.410
[10.41]
.550
[13.97]
.453
[11.5]
A
.010
[.254]
Max. R. Typ.
at Min.
Tolerance
Cutout
.564
[14.33]
.520
[13.2]
.440
[11.18]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Connector Accessories (Continued)
MTA-156
.156 [3.96]
Keying Plugs
Material (RoHS Compliant)
UL94V-2 rated, nylon, natural color
Note: Removal of contact is not necessary when using keying plug.
Panel Mount End Caps
Part No. 641440-1 Part No. 641533-1 (2-position only)
Loose Piece Part No. 640629-1 (Flush)
Used with keyed headers
Flush
Part No. 640630-1 (Long Nose) Used with staked post
Long Nose
On Carrier Strip Part No. 641623-1 (Flush)
(10 per strip)
Material (RoHS Compliant)
UL94V-2 rated, nylon, black
Notes:
1. Both left-hand and right-hand end caps are attached by a con­necting tab. This tab must be broken off prior to installing on connector.
2. For best results attach panel mount end caps to the MTA-156 (IDC) connectors shown on pages 36 thru 39. While not preferred, panel mount end caps can be attached to MTA-156 (IDC) posted connector on page 45.
No. of Dim.
Pos. A
3
4
6
9
12
15
24
42
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
.736
18.69
.892
22.66
1.204
30.58
1.672
42.47
2.140
54.36
2.608
66.24
4.012
101.9
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
3- thru 24-Position
641440-1
See Note 1
(Recommended Panel Thickness .062 [1.57] to .067 [1.70] max.)
Recommended Panel Cutout
Two-Position Only
641533-1
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Posted
641435
641436
641437
641438
641439
641522
MTA-156 Posted Connector/Connector Mateability Guide
Matrix for Tin Plated Part Numbers
This matrix has been pre­pared to assist you, our customer, in defining the correct mating halves for the MTA-156 posted con­nector and connector com­bination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
640426 YYYYYYYYYY
640427 YYYYYYYYYY
640428 YYYYYYYYYY
640429 YYYYYYYYYY
640430 YYYYYYYYYY
640431 NNNNNNNNNN
640432 NNNNNNNNNN
640433 NNNNNNNNNN
640434 NNNNNNNNNN
640435 NNNNNNNNNN
640472 YYYYYYYYYY
640473 YYYYYYYYYY
640474 YYYYYYYYYY
640475 YYYYYYYYYY
640476 YYYYYYYYYY
640477 NNNNNNNNNN
640478 NNNNNNNNNN
640479 NNNNNNNNNN
640480 NNNNNNNNNN
640481 NNNNNNNNNN
640595 YYYYYYYYYY
640599 YYYYYYYYYY
640600 YYYYYYYYYY
640601 YYYYYYYYYY
640602 YYYYYYYYYY
640604 NNNNNNNNNN
640605 NNNNNNNNNN
640606 NNNNNNNNNN
640607 NNNNNNNNNN
640608 NNNNNNNNNN
641301 YYYYYYYYYY
641302 YYYYYYYYYY
641303 YYYYYYYYYY
Connectors
641304 YYYYYYYYYY
641305 YYYYYYYYYY
641306 NNNNNNNNNN
641307 NNNNNNNNNN
641308 NNNNNNNNNN
641309 NNNNNNNNNN
641310 NNNNNNNNNN
643817 NNNNNNNNNN
643818 NNNNNNNNNN
643819 NNNNNNNNNN
643820 NNNNNNNNNN
643821 NNNNNNNNNN
644082 NNNNNNNNNN
644461 NNNNNNNNNN
644462 NNNNNNNNNN
644463 NNNNNNNNNN
644464 NNNNNNNNNN
644465 NNNNNNNNNN
644466 NNNNNNNNNN
644467 NNNNNNNNNN
644468 NNNNNNNNNN
644469 NNNNNNNNNN
644470 NNNNNNNNNN
644471 NNNNNNNNNN
644472 NNNNNNNNNN
644501 NNNNNNNNNN
644502 NNNNNNNNNN
644566 NNNNNNNNNN
644567 NNNNNNNNNN
644569 NNNNNNNNNN
644570 NNNNNNNNNN
644572 NNNNNNNNNN
644783 NNNNNNNNNN
644791 NNNNNNNNNN
644860 YYYYYYYYYY
644878 NNNNNNNNNN
641523
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
641524
641525
Connectors
641526
43
MTA-156
.156 [3.96]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Posted Connector/Connector Mateability Guide (Continued)
This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 posted connector and connector combination. Where a “Y” is indi­cated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating.
MTA-156
.156 [3.96]
Matrix for .000030 [0.00076] Gold Plated Part Numbers
Posted Connectors
641217 YYYY
641218 YYYY
641219 YYYY
641220 YYYY
641221 YYYY
641222 NNNN
641223 NNNN
641224 NNNN
641225 NNNN
641226 NNNN
641227 YYYY
641228 YYYY
641229 YYYY
641230 YYYY
641231 YYYY
Connectors
641232 NNNN
641233 NNNN
641234 NNNN
641235 NNNN
641236 NNNN
644460 NNNN
644662 NNNN
644663 NNNN
644687 NNNN
644718 NNNN
644720 NNNN
644807
644809
644812
644814
Matrix for .000015
Posted Connectors [0.00038] Gold Plated Part Numbers
643995
647476
647481
647497
641148 YYYY
641149 YYYY
641150 YYYY
641151 YYYY
641152 YYYY
641153 NNNN
641154 NNNN
641155 NNNN
641156 NNNN
641157 NNNN
641168 YYYY
641169 YYYY
641170 YYYY
641171 YYYY
Connectors
641172 YYYY
641173 NNNN
641174 NNNN
641175 NNNN
641176 NNNN
641177 NNNN
644284 NNNN
647478 NNNN
647479 NNNN
647496 NNNN
44
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
.840
[21.34]
.126
[3.20]
.100
[2.54]
.045
[1.14]
Sq.
1 2 3 4
A Dim.
.045
[1.14] Sq.
.370
[9.4]
.105
[2.67]
.355
[9.02]
.487
[12.37]
Ref.
1.010
[25.65]
B
Dim.
.156
[3.96]
[ ]
± .010
± 0.25
A Dim.
.045
[1.14] Sq.
.370
[9.4]
.105
[2.67]
.385
[9.78]
.487
[12.37]
Ref.
1.010
[25.65]
B
Dim.
.156
[3.96]
[ ]
± .010
± 0.25
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Posted Connectors (Wire-to-Wire)—Closed End, Feed-Thru
Material and Finish
Closed End Feed-Thru
Housing — UL 94V-2 rated, nylon,
see chart for color Contacts — Copper alloy, post tin or
.000030 [.00076] gold plated over nickel
Notes:
1. Mating half visuals - pages 36 thru 39.
2. Strain relief & dust covers - pages 40
& 41.
3. Approved wire listing - page 70.
Connector Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described connectors.
Prefixes and suffixes are deter­mined by the number of circuit positions in the connector. For example, the complete part number for a 12-position closed end connector for 18 AWG wire would be:
Base number 641435 plus
prefix-and-suffix
4- -2
The correct ordering number is
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent part num-
bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Color Coding by Wire Size for UL 94V-2 Connectors
18 AWG —Orange 20 AWG—Yellow 22 AWG—Red 24 AWG—White 26 AWG—Blue
Performance Data
Voltage Rating —600 VAC Current Rating — 7 amp max. Low-Level Resistance
7 mmax. initial Dielectric Withstanding Voltage
1500 VAC/1 min. Insulation Resistance
5000 Mmin. initial Operating Temperature
-55C to 105C
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
4-641435-2
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Connector Type
& Wire Size Part Nos. RoHS Equiv. Part Nos. RoHS Equiv.
Closed End Connector
Standard UL 94V-2, Tin Plated
18 AWG
0.8-0.9 mm
20 AWG
0.5-0.6 mm
22 AWG
0.3-0.4 mm
24 AWG
2
0.2 mm
26 AWG
0.12-0.15 mm
2
2
2
2
641435 32, 33, 34, 36, 39, 42, 45, 54 641522 32, 33, 34, 36, 39, 42, 45, 54
641436 32, 33, 34, 36, 39, 42, 45, 54 641523 32, 33, 34, 36, 39, 42, 45, 54
641437 32, 33, 34, 36, 39, 42, 45, 54 641524 32, 33, 34, 36, 39, 42, 45, 54
641438 32, 33, 34, 36, 39, 42, 45, 54 641525 32, 33, 34, 36, 39, 42, 45, 54
641439 32, 33, 34, 36, 39, 42, 45, 54 641526 32, 33, 34, 36, 39, 42, 45, 54
Standard UL 94V-2, .000030 [0.00076] Gold Plated
18 AWG
0.8-0.9 mm
20 AWG
0.5-0.6 mm
22 AWG
0.3-0.4 mm
24 AWG
2
0.2 mm
26 AWG
0.12-0.15 mm
2
2
2
2
644807 32, 33, 34, 36, 39, 42, 45, 54 644812 32, 33, 34, 36, 39, 42, 45, 54
2
644809 32, 33, 34, 36, 39, 42, 45, 54 644814 32, 33, 34, 36, 39, 42, 45, 54
2
2
Standard UL 94V-2, .000015 [0.00038] Gold Plated
18 AWG
22 AWG
2
2
AB
.468 .316
11.89 8.03
.624 .472
15.85 11.99
.780 .628
19.81 15.95
1.092 .940
27.74 23.88
0.8-0.9 mm
0.3-0.4 mm
1
MTA-156 Posted Connectors (Closed End and Feed-Thru) will Only mate with MTA-156 connectors with locking ramp and without polarizing tabs. They will NOT mate with MTA-156 Quad Connectors.
2
Parts can be made available upon request. Minimums may apply.
No. of
Circuits
2
3
4
6
Technical Documents
Product Specification
108-1065 MTA-156 Posted
Application Specification
114-1020 MTA-156 Connectors,
Connector
Posted Connectors and Card Edge Connectors
647476 32, 33, 34, 36, 39, 42, 45, 54 647481 32, 33, 34, 36, 39, 42, 45, 54
643995 32, 33, 34, 36, 39, 42, 45, 54 647497 32, 33, 34, 36, 39, 42, 45, 54
Dim.
Suffix
Replacement IDC Contacts
Material and Finish
Contacts — Copper alloy, post tin
plated over nickel
1
Feed-Thru Connector
——2—
——2—
——2—
No. of
Circuits
-2
-3
-4
-6
9
12
15
24
Dim.
AB
1.560 1.408
39.62 35.76
2.028 1.876
51.51 47.65
2.496 2.344
63.40 59.54
3.900 3.748
99.06 95.20
Wire Size
AWG mm
18 0.8-0.9 3-641425-1 20 0.5-0.6 3-641426-1 22 0.3-0.4 3-641427-1 24 0.2 3-641428-1 26 0.12-0.15 3-641429-1
2
1
Prefix/ Suffix
1- -2
1- -5
2- -4
Part
Numbers
MTA-156
.156 [3.96]
-9
45
.250
[6.35]
A
.045
[1.14]
.156
[3.96]
Typ.
.078
[1.98]
Typ.
.450
[11.43]
.125
[3.18]
Solder tail
Length
(See Chart)
.156
[3.96]
Edge of Board
.140
[3.56]
Min.
.125
[3.18]
Post No. 1
Ref.
MTA-156
.156 [3.96]
46
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Flat Headers—Straight
Material and Finish
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
3. .125 [3.18] solder tail lengths are
for .062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36-
3.18] thick printed circuit boards.
4. To determine header overall
length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm].
For mateability options, see matrix on pages 34, 35, 54 and 58.
For mating half visuals, see pages 36 thru 39, 55, 60 and 62.
Recommended Mounting Hole Pattern
Header Ordering
for .062 [1.57] Thk. PC Board
Information
The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts and a .125 [3.18] solder tail length would be:
Base number 640383 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-640383-0
The part numbers in bold face are the RoHS equivalent
version. Example:
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent part num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
No. of
Pos.
2 3-640383–2
24 5-640383-4
Lead Free
RoHS
Prefix/Suffix
thru
Base Part Numbers
Square Posts Round Posts
.125 [3.18] .175 [4.45] .125 [3.18] .175 [4.45]
Solder tail Solder tail Solder tail Solder tail
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
640383 2–24 644749 2–24 640384 2–24 644750 2–24
Standard UL94V-0, .000030 [0.00076] Gold Plated
641202 32–54 644756 32–54 641203 32–54 644757 32–54
Standard UL94V-0, .000015 [0.00038] Gold Plated
641113 32–54 644763 32–54 641114 32–54 644764 32–54
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Note: Consult Product Drawing for details on placing headers onto PC boards.
PC Board Hole Diameters
PC Board Hole Diameters
Square Round
Square Round
Post Post
Post Post
.080/.070 .070/.060
.080/.070 .070/.060
[2.03/1.78] [1.78/1.52]
[2.03/1.78] [1.78/1.52]
.125
[3.18]
A
A
.045
[1.14]
Sq.
.156
[3.96]
Typ.
.078
[1.98]
Typ.
.250
[6.35]
.156
[3.96]
.080/.070
[2.03/1.78]
Solder tail
Length
(See Chart)
.390
[9.91]
Edge of Board
X
Post No. 1
.125
[3.18]
.100
[2.54]
.390
± .015
[9.91
± 0.38
]
.125
[3.18]
16°
Edge of Board
.156
[3.96]
Y
Typ.
Ø .063
± .002
[1.60
± 0.05
]
Typ.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Flat Headers—Right-Angle
Material and Finish
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
3. .125 [3.18] solder tail lengths are
for .062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36-
3.18] thick printed circuit boards.
4. To determine header overall
length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm].
For mateability options, see matrix on pages 34, 35, 54 and 58.
For mating half visuals, see pages 36 thru 39, 55, 60 and 62.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts and a .125 [3.18] solder tail length would be:
Base number 641204 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-641204-0
The part numbers in bold face are the RoHS equivalent ver­sion. Example:
No. of
Pos.
2 3-641204–2
24 5-641204-4
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent part num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Lead Free
RoHS
Prefix/Suffix
thru
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
X = .140 [3.56] Min., .430 [10.92] Max.
when mated with MTA Connector.
X = .140 [3.56] Min. when mated with
SL-156 Wire-to-Board Connector.
Note: Consult Product Drawing for details on placing headers onto PC boards.
Recommended Mounting Hole Pattern for .063 [1.60]
Thk. PC Board for Retentive Leg Header
Y = .140 [3.56] Min., .430 [10.92] Max. when mated with
MTA Connector.
Retentive Leg
Base Part Numbers
Square Posts
Retentive Leg .125 [3.18] Solder tail .175 [4.45] Solder tail
Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647646 2–12 640385 2–24 644751 2–24
Standard UL94V-0, .000030 [0.00076] Gold Plated
—— 641204 32–54 644758 32–54
Standard UL94V-0, .000015 [0.00038] Gold Plated
—— 641115 32–54 644765 32–54
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
47
MTA-156
.156 [3.96]
.156
[3.96]
.125
[3.18]
.450
[11.43]
Solder tail
Length
(See Chart)
.300
[7.62]
A
.156
[3.96]
.045
[1.14]
.180
[4.57]
.078
[1.98]
Post No. 1
.175
[4.45]
Min.
Edge of Board
Y
.425
[10.8]
Ref.
Typ.
Typ.
.068
[1.7]
.400
[10.16]
16°
±
MTA-156
.156 [3.96]
48
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Friction Lock Headers—Straight
Material and Finish
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated,
gold on mating end of post and tin on the solder tail.
3. .125 [3.18] solder tail lengths are
for .062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36-
3.18] thick printed circuit boards.
4. To determine header overall
length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm].
For mateability options, see matrix on pages 34, 35, 54 and 58.
For mating half visuals, use connectors with a locking ramp for polarization/retention pur­poses, see pages 36 thru 39, 55, 60 and 62.
Recommended Mounting Hole Pattern for
.062 [1.57] Thk. PC Board
For polarizing purposes only use connectors without a lock­ing ramp. See pages 36 thru 39, 55, 60 and 62.
Header Ordering Information
The “Base Part Numbers”
PC Board Hole Diameters
Square Round
Post Post
.080/.070 .070/.060
[2.03/1.78] [1.78/1.52]
Retentive Leg
Note: Consult Product Drawing for details
on placing headers onto PC boards.
Chart at right shows the base part number and number of posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts and a .125 [3.18] solder tail length would be:
Base number 641208 plus
prefix-and-suffix 4- -0
The correct ordering number is
4-641208-0
The part numbers in bold face are the RoHS equivalent
version. Example:
No. of Standard
Pos. Prefix/Suffix
2 641208–2 3-641208–2
24 2-641208-4 5-641208-4
See page 15 for an explanation of RoHS lead free equivalents.
thru
Lead Free
RoHS
Prefix/Suffix
Base Part Numbers
Square Posts Round Posts
Retentive .125 [3.18] .175 [4.45] .125 [3.18] .175 [4.45]
Leg Solder tail Solder tail Solder tail Solder tail
Header RoHS Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
1744017 2-12 640445 2–24 644752 2–24 640388 2–24 644753 2–24
Standard UL94V-0, .000030 [0.00076] Gold Plated
——641208 32–54 644759 32–54 641209 32–54 644760 32–54
Standard UL94V-0, .000015 [0.00038] Gold Plated
——641119 32–54 644766 32–54 641120 32–54 644767 32–54
Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not
available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) and tube loaded product are available upon request. Please contact product engineer or product manager for details.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Y = .068 [1.73] Max. 2-8
position tin plated and 2–24 position gold plated headers.
Y = .073 [1.85] 9-24 position
tin plated headers.
.125
[3.18]
.450
[11.43]
.212
[5.38]
.425
[10.8]
.156
[3.96]
Y
.045
[1.14]
Sq.
.180
[4.57]
A
.300
[7.62]
.078
[1.98]
Typ.
Typ.
.156
[3.96]
.080/.070
[2.03/1.78]
Edge of Board
Post No. 1
X
Solder tail
Length
(See Chart)
.425
[10.8]
.157
[3.99]
Y
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Friction Lock Headers—Right-Angle
Material and Finish
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated,
.000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying pur-
poses. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated, gold
on mating end of post and tin on the solder tail.
3. .125 [3.18] solder tail lengths are for
.062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36-3.18] thick printed circuit boards.
4. To determine header overall length
(Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals
1.560 inches [39.62 mm].
For mateability options, see matrix on pages 34, 35, 54 and 58.
When using Front Bend Headers — for mating half visuals use connectors with a locking ramp for polarization/ retention purposes. When using Rear Bend Headers — for mating half visuals use connectors with­out a locking ramp. For polariza­tion purposes only see pages 36 thru 39, 55, 60 and 62.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers.
Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts, front bend, and a .125 [3.18] solder tail length would be:
Base number 641210 plus
prefix-and-suffix
4- -0
The correct ordering number is
The part numbers in bold
4-641210-0
face are the RoHS equivalent
version. Example:
No. of Standard
Pos. Prefix/Suffix
2 641210–2 3-641210–2
24 2-641210-4 5-641210-4
See page 15 for an explanation of RoHS lead free equivalents.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
thru
Lead Free
RoHS
Prefix/Suffix
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
640389 2–24 644754 2–24 640387 2–24 644755 2–24
Standard UL94V-0, .000030 [0.00076] Gold Plated
641210 32–54 644761 32–54 641207 32–54 644762 32–54
Standard UL94V-0, .000015 [0.00038] Gold Plated
641121 32–54 644768 32–54 641118 32–54 644769 32–54
Note: All RoHS equivalent part num-
bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
Recommended Mounting Hole Pattern
for .062 [1.57] Thk. PC Board
Note: Consult Product Drawing for details
on placing headers onto PC boards.
Square Posts
Front Bend Rear Bend
.125 [3.18] .175 [4.45] .125 [3.18] .175 [4.45]
Solder tail Solder tail Solder tail Solder tail
Front Bend
X = .325 [8.26] Min., .400 [10.16]
Max., when mated with MTA Connector.
X = .325 [8.26] Min., .345 [8.76]
Max., when mated with SL-156 Connector.
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Y = .068 [1.73] Max. 2-8
position tin plated and 2–24 position gold plated headers.
Y = .073 [1.85] 9-24 position
tin plated headers.
Rear Bend
X = .500 [12.7] Min., .650 [16.51]
Max., when mated with MTA Connector.
X = .500 [12.7] Min., when mated
with SL-156 Connector.
49
MTA-156
.156 [3.96]
MTA-156
.210
[5.33]
A
.125
[3.18]
.156
[3.96]
.076
[1.93]
.045
[1.14]
.425
[10.80]
.100
[2.54]
.125
[3.18]
.450
[11.43]
.545
[13.84]
.073
[1.85]
.156
[3.96]
.066/.062
[1.68/1.57]
Edge of Board
Dia.
.167
[4.24]
.225
[5.72]
Min.
.078
[1.98]
90° Ref.
Typ.
Retention Tabs 4 Plc.
Post No. 1
Polarized Retention Peg
Typ.
Peg Hole
.156 [3.96]
Material and Finish
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated or
.000030 [0.00076] gold over nickel
Notes:
1. Post(s) can be omitted for keying pur-
poses. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Peg holes are not required in
PC Boards when headers without pegs are used.
3. One peg only on a 2 position header,
other position sizes have two pegs.
4. Headers with .00015 [0.00038] gold
plated post are available upon request. Minimums may apply.
5. To determine header overall length
(Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals
1.560 inches [39.62 mm].
For mateability options, see matrix on pages 34, 35, 54 and 58.
For mating half visuals, use connectors with a locking ramp for polarization/retention pur­poses, see pages 36 thru 39, 55, 60 and 62.
For polarizing purposes only use connectors without a lock­ing ramp. See pages 36 thru 39, 60 and 62.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Polarized Lock Headers—Straight
Polarized
Retention Peg
PC Board Hole Diameters
Square Round
Post Post
.069/.065 .054/.050
[1.75/1.65] [1.37/1.27]
Header Ordering Information
Recommended Mounting Hole Pattern
for .062 [1.57] Thk. PC Board
Note: Consult Product Drawing
for details on placing headers onto PC boards.
The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts with pegs would be:
Base number 644615 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-644615-0
The part numbers in bold face are the RoHS equivalent
version. Example:
No. of
Pos.
2 3-644615–2
18 4-644615-8
See page 15 for an explanation of RoHS lead free equivalents.
Lead Free
RoHS
Prefix/Suffix
thru
Base Part Numbers
Square Posts Round Posts
Without Pegs With Pegs Without Pegs With Pegs
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
644611 32–48 644615 32–48 644612 32–48 644616 32–48
Standard UL94V-0, .000030 [0.00076] Gold Plated
Note: All RoHS equivalent part num-
bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
644627 32–48 644631 32–48 644628 32–48 644632 32–48
50
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
.125
[3.18]
.156
[3.96]
.076
[1.93]
Typ.
.045
[1.14]
.210
[5.33]
Typ.
Ref.
.450
[11.43]
.545
[13.84]
.156
[3.96]
Edge of Board
Dia.
.239
[6.07]
Reg. Hole
.066/.062
[1.68/1.57]
.078
[1.98]
.069/.065
[1.75/1.65]
90° Ref.
Typ.
Retention Tabs 4 Plc.
Post No. 1
A
.100
[2.54]
.425
[10.80]
Front Bend Rear Bend
.205
[5.21]
Typ.
.073
[1.85]
Typ.
.125
[3.18]
.200
[5.08]
Typ.
.125
[3.18]
x
Typ.
Sq.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Polarized Lock Headers—Right-Angle
Material and Finish
Housing — UL94V-0 rated, polyester,
white Posts — Copper alloy, tin plated or
.000030 [0.00076] gold over nickel
Notes:
1. Post(s) can be omitted for keying
purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Peg holes are not required in PC
3. One peg only on a 2 position
header, other position sizes have two pegs.
4. Headers with .00015 [0.00038]
gold plated post are available upon request. Minimums may apply.
5. To determine header overall
length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm].
For mateability options, see matrix on pages 34, 35, 54 and 58.
For mating half visuals, use only connectors with a locking ramp for polarization/retention purposes, see pages 36 thru 39, 55, 60 and 62.
For polarizing purposes only use connectors without a lock­ing ramp. See pages 36 thru 39, 60 and 62.
Recommended Mounting Hole Pattern
for .062 [1.57] Thk. PC Board
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with front bend and with pegs would be:
Base number 644617 plus
The correct ordering number is
The part numbers in bold face are the RoHS equivalent version. Example:
prefix-and-suffix
4-644617-0
No. of
Pos.
4- -0
Lead Free
RoHS
Prefix/Suffix
2 3-644617–2
thru
18 4-644617-8
See page 15 for an explanation of RoHS lead free equivalents.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Base Part Numbers
Standard UL94V-0, Tin Plated
Standard UL94V-0, .000030 [0.00076] Gold Plated
Note: All RoHS equivalent part num-
bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
Without Pegs With Pegs Without Pegs
Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
644613 32–48 644617 32–48 644614 32–48
644629 32–48 644633 32–48 644630 32–48
Front Bend Rear Bend
Polarized
Retention Peg
X = .350 [8.89] Min., .825 [20.96]
Max., when mated with MTA Connector.
X = .350 [8.89] Min. when mated
with SL-156 Connector.
Square Posts
Front Bend
Rear Bend
X = .500 [12.7] Min., .700 [17.78]
Max., when mated with MTA Connector.
X = .500 [12.7] Min., when
mated with SL-156 Connector.
Note: Consult Product Drawing for details on placing headers onto PC boards.
51
MTA-156
.156 [3.96]
Ø .045
± .001
[1.14
± 0.03
]
.076
± .003
[1.93
± 0.08
]
2 Plcs.
.210
[5.33]
.450
[11.43]
.125
[3.18]
Mating
End
Solder tail
Post No. 1
A
Ref.
.156
[3.96]
Typ.
.425
[10.80]
.335
[8.51]
.700
± .010
[17.78
±0.25
]
.125
± .010
[3.18
±0.25
]
Ref.
Ref. Typ.
+ .005 – .010
+0.13 –0.25
.073
[1.85 ]
.545
± .010
[13.84
±0.25
]
Typ.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Friction Lock High Temperature Headers—Straight
MTA-156
.156 [3.96]
Material and Finish
For use with Infrared Reflow Process
Housing —UL94V-0 rated, nylon, black Posts — Copper alloy, tin plated,
.000015 [0.00038] gold over nickel
Temperature—Maximum Temperature Rating: 280°C
Notes:
1. Post(s) can be omitted for keying pur-
poses. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated, gold
on mating end of post and tin-lead on the solder tail.
3. Headers with straight and right-angle
square posts are available upon request. Minimums may apply.
4. To determine header overall length
(Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals
1.560 inches [39.62 mm].
For mateability options, see matrix on pages 34, 35, 54 and 58.
For mating half visuals, use connectors with a locking ramp for polarization/retention pur­poses, see pages 36 thru 39, 55, 60 and 62.
For polarizing purposes only use connectors without a lock­ing ramp. See pages 36 thru 39, 60 and 62.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with round tin plated posts:
Base number 647648 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-647648-0
±.010
.650
± 0.25
[16.51
Solder Paste Area
]
.120
Typ.
[3.05]
.120
Typ.
[3.05]
.070
Typ.
[1.78]
Recommended Mounting Hole Pattern
for .062 [1.57] Thick PC Board
Note: Consult Product Drawing for details
on placing headers onto PC boards.
.156
[3.96]
Typ.
.008
[0.20]
Min. Thick Solder Paste in Area Shown
Position No. 1
±.003
.057
± 0.08
[1.45
] Pretinned Plated Thru Hole Typ.
.100
[2.54]
Pretinned Land (Both Sides) Typ.
The part numbers in bold face are the RoHS equivalent
version. Example:
No. of
Pos.
2 3-647648–2
12 4-647648-2
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent part num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Lead Free
RoHS
Prefix/Suffix
Base Part Numbers
Header RoHS
Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647648 32–42
Standard UL94V-0, .000015 [0.00038] Gold Plated
647649 32–42
Round Post
Note:
Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details.
52
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
A
.455
[11.56]
.125
[3.18]
.045
[1.14]
Post
No. 1
.156
[3.96]
.550
[13.97]
.525
[13.34]
.300
[7.62]
.125
[3.18]
.100
[2.54]
.167
[4.24]
.210
[5.33]
.066/062
[1.68/1.58]
Dia.
.156
[3.96]
.078
[1.98]
.167
[4.24]
.245
[6.22]
Edge of Board
Min.
.066/062
[1.68/1.58]
Dia.
.156
[3.96]
.078
[1.98]
.239
[6.07]
.350/.700
[8.89/17.78]
.069/.065
[1.75/1.65]
Edge of Board
Dia.
Post
No. 1
.156
[3.96]
Typ.
.045
[1.14]
.525
[13.34]
Ref.
.300
[7.62]
Ref.
.455
[11.56]
.210
[5.33]
.205
[5.21]
.125
[3.18]
Post
No. 1
.156
[3.96]
Typ.
.045
[1.14]
.525
[13.34]
Ref.
.300
[7.62]
Ref.
.455
[11.56]
.210
[5.33]
.205
[5.21 ]
± .002 ± 0.05
.125
[3.18 ]
± .010 ± 0.25
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 Shrouded Headers—Straight and Right-Angle
Material and Finish
Straight Post (.045 [1.14] Square or Round) Right-Angle (.045 [1.14] Square)
Housing — UL94V-0 rated, polyester,
black Posts — Copper alloy, tin plated; or .000030 [0.00076] or .000015 [0.00038] gold over nickel
Notes:
1. Post(s) can be omitted for keying pur­poses. Specify the desired post(s) to be omitted using the figure to identify Post No. 1.
2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail.
3. Peg holes are not required in PC boards when headers without pegs are used.
4. One peg only on a 2 position header, other position sizes have two pegs.
5. Right-angle front and rear bend headers with retention pegs can be made avail­able upon request. Minimums may apply.
Polarized
Retention Peg
Front Bend
For mateability options, see matrix on pages 34, 35, 54 and 58.
For mating half visuals, see pages 36 thru 39 and 55.
Header Ordering Information
The “Base Part Numbers” Chart at right shows the base
PC Board Hole Diameters
Square Post Round Post
.069/.065 .054/.050
[1.75/1.65] [1.37/1.27]
Note: Consult Product Drawing for details on placing headers onto PC boards.
Rear Bend
part number and number of posts available for the described headers.
Prefixes and suffixes are deter­mined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight, square posts and with pegs would be:
Recommended Mounting Hole Pattern for .062 [1.57] Thick
PC Board Using a Straight Post Header
Recommended Mounting Hole Pattern for .062 [1.57] Thick
PC Board Using a Right-Angle Header
Base number 647127 plus
prefix-and-suffix
4- -0
The correct ordering number is
4-647127-0
RoHS
Prefix/
Suffix
2--2
2--3
2--4
2--5
2--6
2--7
2--8
2--9
3--0
3--1
3--2
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
No. of Dim.
Pos. A
.406
2
10.31
.562
3
14.27
.718
4
18.24
.874
5
22.20
1.030
6
26.16
1.186
7
30.12
1.342
8
34.09
1.498
9
38.05
1.654
10
42.01
1.810
11
45.97
1.966
12
49.94
Note: All RoHS equivalent part num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Base Part Numbers
Straight Square Posts Straight Round Posts
Without Pegs With Pegs Without Pegs With Pegs
Header RoHS Header RoHS Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647123 22–32 647127 22–32 647124 22–32 647128 22–32
Standard UL94V-0, .000030 [0.00076] Gold Plated
647131 22–32 647135 22–32 647132 22–32 647136 22–32
Standard UL94V-0, .000015 [0.00038] Gold Plated
647139 22–32 647143 22–32 647140 22–32 647144 22–32
Square Posts
Right-Angle Posts, Front Bend Right-Angle Posts, Rear Bend
Without Pegs Without Pegs
Header RoHS Header RoHS
Part Nos. Equiv. Part Nos. Equiv.
Standard UL94V-0, Tin Plated
647125 22–32 647126 22–32
Standard UL94V-0, .000030 [0.00076] Gold Plated
647133 22–32 647134 22–32
Standard UL94V-0, .000015 [0.00038] Gold Plated
647141 22–32 647142 22–32
Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or prod-
uct manager for details.
53
MTA-156
.156 [3.96]
644329 644370 644371 644375 644376 644377 644381 644382 644383 644387 644388 644389
640389
Y Y Y Y Y Y Y Y Y Y Y Y
640385
Y Y Y Y Y Y Y Y Y Y Y Y
640383
Y Y Y Y Y Y Y Y Y Y Y Y
640445
Y Y Y Y Y Y Y Y Y Y Y Y
644611
Y Y Y Y Y Y Y Y Y Y Y Y
644613
Y Y Y Y Y Y Y Y Y Y Y Y
Connectors
Headers
644615
Y Y Y Y Y Y Y Y Y Y Y Y
644617
Y Y Y Y Y Y Y Y Y Y Y Y
644749
Y Y Y Y Y Y Y Y Y Y Y Y
644751
Y Y Y Y Y Y Y Y Y Y Y Y
644752
Y Y Y Y Y Y Y Y Y Y Y Y
644754
Y Y Y Y Y Y Y Y Y Y Y Y
647123
Y Y Y Y Y Y Y Y Y Y Y Y
647125
Y Y Y Y Y Y Y Y Y Y Y Y
647126
Y Y Y Y Y Y Y Y Y Y Y Y
647127
Y Y Y Y Y Y Y Y Y Y Y Y
R
R
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Quad Connectors
MTA-156
.156 [3.96]
Product Facts
Provides four points of
contact
Greater current carrying
capability than Standard MTA-156 Connectors
Connector styles include
both closed end and feed­thru with locking ramp, with and without polarizing tabs in 2 through 12 positions
Available for wire ranges of
18 – 22 AWG [0.9– 0.3
mm
]
Contacts are lubricated for
fretting corrosion protection
Complies with
Tyco Electronics Quality Specification 102-6, “Preparation of Design Objectives”
Uses existing MTA applica-
tion tooling for termination
Quad connectors preloaded
with contacts
All contacts are slotted for
insulation displacement (IDC) termination technique
Connectors and headers are
end-to-end stackable
AWG size is “frosted” on
the side of the connector
Recognized under the
Component Program of Underwriters Laboratories Inc., File No. E28476
Certified by Canadian
Standards Association, File No. LR 7189
Satisfies the VDE require-
ments according to VDE 110, Insulation Group B, 250 vac for air and creep­age paths
The MTA-156 Quad Con­nector provides a connec­tion with four points of contact. The UL94V-0 rated connector with multi-point contacts provides greater current carrying capability than the Standard MTA-156 Connector. These connec­tors comply with Tyco Electronics Quality Specification 102-6* and satisfy the VDE requirements according to VDE 110.
The connectors are avail­able for wire ranges of 18 – 22 AWG [0.9– 0.3 mm
2
] and in a variety of styles including closed end and feed-thru with locking ramp, with and without polarizing tabs.
Only one wire to be termin­ated into an IDC contact
The MTA-156 Quad Connectors only mate with standard MTA­156 square post headers and use existing MTA application tooling for termination.
slot.
*The 102-6 Quality Specification is the new procedure for “Preparation of Design Objectives”. Its purpose is to provide a means for verifying the maximum current carrying capacity of the device.
Note: Refer to pages 70 through 74 for approved wire listings.
This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 header and connector combination. Where a “Y” is indi­cated the combination is a valid mating pair.
Performance Data
Voltage Rating —600 vac Current Rating — 12.5 amp max. on a
single circuit. For Multiple Circuit Loading
refer to Product Specification for current rating chart.
Low-Level Resistance
3.0 mmax. initial Dielectric Withstanding Voltage
1500 vac/1 min. Insulation Resistance
5000 Mmin. initial Operating Temperature
-55C to 105C
Technical Documents
Product Specifications
108-1219 MTA-156 Quad Connector
System
Application Specifications
114-1048 MTA-156 Quad
Connector
54
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Closed End with Locking Ramp
.156
[3.96]
Typ.
A
.097
[2.46]
.100
[2.54]
.308
[7.82]
.725
[18.42]
.245
[6.22]
.100
[2.54]
.325
[8.26]
.355
[9.02]
.280
[7.11]
.180
[4.57]
.230
[5.84]
.090
[2.29]
.725
[18.42]
.245
[6.22]
.100
[2.54]
.325
[8.26]
.385
[9.78]
.230
[5.84]
.180
[4.57]
.090
[2.29]
.280
[7.11]
.156
[3.96]
Typ.
A
.097
[2.46]
.100
[2.54]
.308
[7.82]
.562
[14.27]
.116
[2.95]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Quad Connectors—Closed End and Feed-Thru
AWG
without Polarizing Tabs with Polarizing Tabs
AWG
Feed-Thru with Locking Ramp
AWG
without Polarizing Tabs
AWG
with Polarizing Tabs
Material and Finish
Housing — UL94V-0 rated, nylon,
black Contacts — High conductivity copper
alloy, post tin plated
For mateability options, see matrix on page 54.
For strain relief and dust covers, see pages 40 and 41.
For mating half visuals, see pages 46 thru 48 and 50, 52 and 53, (49 and 51 Front
Base Part Numbers
Connector Type
& Wire Size
Standard UL94V-0, Tin Plated
18 AWG
0.8-0.9 mm
20 AWG
0.5-0.6 mm
22 AWG
0.3-0.4 mm
Connector RoHS Connector RoHS Connector RoHS Connector RoHS
Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv. Part Nos. Equiv.
2
2
2
644329 32–42 644381
644370 32–42 644382 32–42 644376 32–42 644388 32–42
644371 32–42 644383 32–42 644377 32–42 644389 32–42
Closed End with Locking Ramp Feed-Thru with Locking Ramp
Without Tabs With Tabs Without Tabs With Tabs
32–42
644375 32–42 644387 32–42
Bend Headers only). Mates with tin-plated square
posts
only.
Refer to pages 70 thru 74 for approved wire listing.
Note: To determine connector overall length (Dim. A), multiply .156 x the number of circuits. Example: .156 x 10 circuits equals 1.560 inches [39.62 mm].
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Connector Ordering Information
The “Base Part Numbers” Chart above shows the base part number and number of circuits available for the described connectors.
Prefixes and suffixes are deter­mined by the number of circuit positions in the connector. For example, the complete part number for a 10-position closed end connector with locking ramp and without polarizing tabs for 18 AWG wire would be:
Base number 644329 plus
prefix-and-suffix
1- -0
The correct ordering number is
1-644329-0
The set of numbers in bold face are the RoHS equivalent ver­sion of the standard product. Example:
thru
Lead Free
RoHS
Prefix/Suffix
No. of Standard
Pos. Prefix/Suffix
2 644329–2 3-644329–2
12 1-644329-2 4-644329-2
See page 15 for an explanation of RoHS lead free equivalents.
Note: All RoHS equivalent par t num­bers may not be available upon cat­alog release. If the number you need is not available, please contact Product Engineering to expedite your request.
Replacement IDC Contacts
Material and Finish
Contacts — High conductivity copper
alloy post tin plated
Wire Size
AWG mm
18 0.8-0.9 3-644508-1 20 0.5-0.6 3-644509-1 22 0.3-0.4 3-644510-1
Note: Tyco Electronics does not rec­ommend terminating an MTA contact more than one time. Use replace­ment contacts when required for field repairs or wire gage changes.
2
Part
Numbers
55
MTA-156
.156 [3.96]
.170
[4.32]
.156
[3.96]
Typ.
A
B
C
.161
[4.09]
.094
[2.39]
.380
[9.65]
.075
[1.91]
.677
[17.2]
.440
[11.18]
Ref.
.300
[7.62]
.125
[3.18]
Dia.
.312
[7.92 ]
± .005
± 0.13
.015
[0.38 ]
± .005
± 0.13
.100
[2.54]
Min.
.100
[2.54]
Min.
Circuitry
side
.090
[2.29]
Min.
.156
[3.96]
Typ.
x 45° Cham. Both sides
D
[ ]
± .005
± 0.13
B
E
.145
[3.68]
.375
[9.53]
.138
[3.51]
.075
[1.91]
R.
.130
[3.3] Typ.
Material and Finish
Housing — UL94V-0 rated, polyester,
see chart for color Contacts — Phosphor bronze, post tin
plated
Note: Refer to pages 70 thru 74 for approved wire listings.
Color Coding by Wire Size for UL94V-0 Connectors
26 AWG—Blue 24 AWG—White 22 AWG—Red 20 AWG—Yellow 18 AWG—Orange
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Card Edge Connectors—Closed End and Feed-Thru
MTA-156
.156 [3.96]
Connector Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and num­ber of circuits available for the described connectors.
Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 12-position closed end con­nector without mounting ears for 18 AWG wire would be:
Base number 640859 plus
prefix-and-suffix
1- -2
The correct ordering num­ber is
1-640859-2
See page 15 for an explanation of RoHS lead free equivalents.
Performance Data
Voltage Rating —600 vac Current Rating — 5 amp max. Low-Level Resistance
7 mmax. initial
Dielectric Withstanding Voltage
Base Part Numbers
Connector Type
Standard UL94V-0, Tin Plated
0.12-0.15 mm
Recommended PC Board Layout
for .062 [1.57] Thk. PC Board
& Wire Size
Connector Circuits/ Connector Circuits/ Connector Circuits/ Connector Circuits/
Part Nos. RoHS Part Nos. RoHS Part Nos. RoHS Part Nos. RoHS
18 AWG
0.8-0.9 mm
20 AWG
0.5-0.6 mm
22 AWG
0.3-0.4 mm
24 AWG
0.2 mm
26 AWG
640859
2
640860
2
640861
2
640862
2
640863
2
Closed End Feed-Thru
Without With Without With
Mounting Ears Mounting Ears Mounting Ears Mounting Ears
No. of No. of No. of No. of
Equiv. Equiv. Equiv. Equiv.
3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12,
15,18, 20-24
33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42,
45, 48, 50-54 45, 48, 50-54 45, 48, 50-54 45, 48, 50-54
3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12,
15,18, 20-24
33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42,
45, 48, 50-54 45, 48, 50-54 45, 48, 50-54 45, 48, 50-54
3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12,
15,18, 20-24
33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42,
45, 48, 50-54 45, 48, 50-54 45, 48, 50-54 45, 48, 50-54
3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12,
15,18, 20-24
33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42,
45, 48, 50-54 45, 48, 50-54 45, 48, 50-54 45, 48, 50-54
3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12, 3, 6, 9, 12,
15,18, 20-24
33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42, 33, 36, 39, 42,
45, 48, 50-54 45, 48, 50-54 45, 48, 50-54 45, 48, 50-54
640864
640865
640866
640867
640868
15,18, 20-24
15,18, 20-24
15,18, 20-24
15,18, 20-24
15,18, 20-24
1250 vac/1 min. Insulation Resistance
5000 Mmin. initial Operating Temperature
55C to 105C
Technical Documents
Product Specification
108-1058 MTA-156 Card Edge
Application Specification
114-1020 MTA-156 Connectors,
56
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Connectors
Posted Connectors and Card Edge Connectors
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
No. of
Circuits
3 .500 [12.70] .926 [23.52] 1.248 [31.70] .484 [12.29] .650 [16.51] -3 6 .968 [24.59] 1.394 [35.41] 1.716 [43.59] .952 [24.18] 1.118 [28.40] -6
9 1.436 [36.47] 1.862 [47.29] 2.184 [55.47] 1.420 [36.07] 1.586 [40.28] -9 12 1.904 [48.36] 2.330 [59.18] 2.652 [67.36] 1.888 [47.96] 2.054 [52.17] 1- -2 15 2.372 [60.25] 2.798 [71.07] 3.120 [79.25] 2.356 [59.84] 2.522 [64.06] 1- -5 18 2.840 [72.14] 3.266 [82.96] 3.588 [91.14] 2.824 [71.73] 2.990 [75.95] 1- -8 20 3.152 [80.06] 3.578 [90.88] 3.900 [99.06] 3.136 [79.65] 3.302 [83.87] 2- -0 21 3.308 [84.02] 3.734 [94.84] 4.056 [103.02] 3.292 [83.62] 3.458 [87.83] 2- -1 22 3.464 [87.99] 3.890 [98.81] 4.212 [106.98] 3.448 [87.58] 3.614 [91.80] 2- -2 23 3.620 [91.95] 4.046 [102.77] 4.368 [110.95] 3.604 [91.54] 3.770 [95.76] 2- -3 24 3.776 [95.91] 4.202 [106.73] 4.524 [114.91] 3.760 [95.50] 3.926 [99.72] 2- -4
ABCDE
Dimensions
Recommended Panel Cutout
641283
641284
641285
641286
641287
15,18, 20-24
15,18, 20-24
15,18, 20-24
15,18, 20-24
15,18, 20-24
641288
641289
641290
641291
641292
15,18, 20-24
15,18, 20-24
15,18, 20-24
15,18, 20-24
15,18, 20-24
Prefix/
Suffix
Dust Cover
.130
[3.3]
.609
[15.47]
.126
[3.2]
.100
[2.54]
A
.130
[3.3]
.530
[13.46]
Retention Dimple
.195
[4.95]
.075
[1.91]
.074
[1.88]
1.150
[29.21]
.900
[22.86]
.170
[4.32]
.100
[2.54]
Material (RoHS Compliant)
UL94V-0 rated, polyester, white
Cover is for both Closed End and Feed-Thru connectors
Cover Ordering Information
The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described cover.
Prefixes and suffixes are determined by the number of circuit positions in the cover. For example, the complete part number for a 12-position dust cover would be:
Base number 641106 plus
prefix-and-suffix
1- -2
The correct ordering number is
1-641106-2
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA-156 IDC Card Edge Accessories
Base Part Number
Cover Part No. No. of Circuits
641106 3, 6, 9, 12, 15, 18, 20-24
No. of Dim. Prefix/
Circuits A Suffix
3
6
9
12
15
18
20
21
22
23
24
.504
12.80
.972
24.69
1.440
36.58
1.908
48.46
2.376
60.35
2.844
72.24
3.156
80.16
3.312
84.12
3.468
88.09
3.624
92.05
3.780
96.01
1- -2
1- -5
1- -8
2- -0
2- -1
2- -2
2- -3
2- -4
MTA-156
.156 [3.96]
Locking Plugs
-3
-6
-9
Material (RoHS Compliant)
UL94V-2 rated, nylon, white
Part Number 641101-1
Note: Contact must be removed to
install locking plug.
Material (RoHS Compliant)
UL94V-2 rated, nylon, white
Part Number 641293-1
Replacement IDC Contacts
Material and Finish
Phosphor bronze; post tin plated
Part Numbers
3-640991-1 (18 AWG [0.8-0.9 mm2]) 3-640992-1 (20 AWG [0.5-0.6 mm2]) 3-640993-1 (22 AWG [0.3-0.4 mm2]) 3-640994-1 (24 AWG [0.2 mm2]) 3-640995-1 (26 AWG [0.12-0.15 mm2])
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Note: Contact can remain during locking plug installation.
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
57
SL-156
R
R
Y
647230
N
Y
N
YY
YYY YYY
647227
647228
647229
647260
Y
Y
N
644769
647262
N Y
Y
647261
Y Y
Y
Y
Y Y
644751
YYYYN YYYYY YYYYN
644752
644753
644754
644755
YYYY YYYY YYYY
YN
YYNY
YY
644756
644757
644758
644759
644760
644761
644762
Y
641113
647401 YYYYY 647400 YYYYY 647402 YYYYY
Y
YYY
Y
YYY
Y
YYY
YY
YYYY
YY
641114
641115
N Y N
641118
641119
641120
641121
644763
644764
644765
644766
644767
644768
Headers
640383
647401 YYYNY 647400
LID
LID
LID
YYYYY
647402 YYYNY
YY YY YY
Y Y Y
640384
640385
640387
640388
640389
640445
644611
644612
644613
644614
644615
644616
644617
Y Y Y
Y Y Y
N
Y
N
Y Y Y
Y Y Y
Y Y Y
644750
Y Y Y
Headers
644749
Y
644322
Y Y Y
Y Y
N
647401 647400 647402
YY YY YY
Y YYY
YYYNYY
YYYY YYY
640250 640251 770849
Housings
640250 640251
Standard
Standard
Standard
770849
Housings
640250 640251 770849
Housings
641202
641203
641204
641207
641208
641209
641210
644627
644628
644629
644630
644631
644632
Y Y Y
Y Y Y
Y Y Y
N Y N
Y Y Y
Y Y Y
Headers
644633
Y Y Y
Y
.156 [3.96]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
.156 [3.96] Centerline SL-156 Crimp Contacts and Housings
Product Facts
Rugged wire-to-board
interconnection to mate with .045 square or round post headers or staked posts on .156 centers
Standard Connectors accept
wire range of 18–24 AWG [0.9–0.2 mm
] and LID Connectors accept wire range of 18–24 AWG [0.9–0.2 mm ited 16 AWG [1.29–1.42
mm
Two-piece interconnection
] and a lim-
] (2550–2800 CMA)
system (connector/header)
Housing made of flame
retardant nylon
Available in 1- through
24-position connector configurations
Connectors are end-to-end
stackable
Wire-to-board system offers
polarization with friction lock for positive mating
These matrixes represent only the housing and header combinations. You also need to consider the plating on the contacts and headers. Gold contacts with gold headers and tin contacts with tin headers.
Meets the material
requirements of Table 23.1 of UL1410 Standard for High-Voltage Television Receivers and Video Productions
Recognized under the
Component Program of Underwriters Laboratories Inc., File No. E28476
Certified by Canadian
Standards Association, File No. LR7189
Technical Documents
Product Specification
108-1049, 108-1049-1, 108-1049-2
Application Specification
114-1021
The AMP SL-156 connec­tors shown on the following pages are designed to mate with .045 [1.14] square or round post headers or staked posts on .156 [3.96] centers.
The wire-to-board connector is a two-piece connector system with the wire crimped to the contact, then inserted into the hous­ing. This product mates with the MTA-156 flat, polarized and friction lock header, or staked posts (not MTA-156 shrouded headers).
Performance Data
Voltage Rating —250 vac Current Rating
10 amp max. at 250 vac Low-Level Resistance
3.0 mmax. initial Dielectric Withstanding Voltage
2000 vac/1 min. Insulation Resistance
1000 Mmin. initial Operating Temperature
55C to 105C
The Large Insulation Diameter (LID) Contacts and Housings are for use in applications where wire insulation is up to .112 [2.84] in diameter.
Matrix for Tin Plated Part Numbers
Matrix for .000030 [0.00076] Gold Plated Part Numbers
Matrix for .000015 [0.00038] Gold Plated Part Numbers
58
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Contacts
.115
[2.92]
.121/.115
[3.07/2.92]
.145/.140
[3.68/3.56]
.230
[5.84]
.180
[4.57]
.131
±.004
[3.33
±0.10
]
.300
[7.62]
.225
[5.72]
.300
[7.62]
Material and Finish
.012 [0.3] bright tin plated brass or phosphor bronze; .012 [0.3] pre-tin brass; or .012 [0.3] brass or phosphor bronze with .000030 [0.00076] gold over nickel (see chart)
All tin-plated contacts are
post lubricated to resist fretting corrosion
Maximum insulation
diameter is .105 [2.67]
Wire range is 18-30 AWG
[0.9-0.06 mm
2
]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
SL-156 Crimp Contacts and Keying Plugs
A
High Force
(6.5 Amp Max. Current Rating)
C
Hooded (Dual Wipe)
(10 Amp. Max. Current Rating)
B
Low Force
(6.5 Amp Max. Current Rating)
SL-156
.156 [3.96]
Application Note
Part No. 640252 has a higher mating and un­mating force than Part No. 350980 and is recom­mended to be used only in housings with 1 through 12 positions. Part No. 350980 can be used in any size housing but is recommended to be used in housings with 13 through 24 positions. Part No. 770476 is recom­mended for use in any size housing. Its mating force is similar to Part No. 350980 while unmating force is similar to 640252.
For housings, see pages 60 and 61.
Keying Plugs
Wire Size
AWG mm
24–30
0.2-0.06
18–24
0.9-0.2
Contact Material and Finish
2
A brass, pre-tin plated 641550-1
A brass, pre-tin plated 640252-2 640706-2
B
C phosphor bronze, gold plated 770476-2 770522-2
Part Numbers
Strip Loose Piece
brass, bright tin plated 640252-1 640706-1
brass, RoHS Compliant 3-640252-1 3-640706-1 brass, bright tin plated 350980-1 640707-1 brass, pre-tin plated 350980-2 — brass, gold plated 350980-3 770258-1 brass, RoHS Compliant 3-350980-1 3-640707-1 phosphor bronze, bright tin plated 770476-1 770522-1
phosphor bronze, RoHS Compliant 3-770476-1 3-770522-1
Application Tooling
Extraction Tool Part No. 90471-1
Loose Piece Contacts — PRO-CRIMPER II Hand Tool
Part No. 58614-1 (408-4228) [For field service use only]
For CERTI-CRIMP hand tool, contact Technical Support.
Strip Contacts — AMP-O-LECTRIC Model “G”
Termination Machine* Applicator 680211-3 (Request Catalog 65828)
AMP-O-LECTRIC Model “K” Termination Machine* Applicator 466468-2
AMP-O-MATIC Stripper-Crimper Machine* SCA 466947-1 or 567828-1 (with CQM) (Request Catalog 65004)
AMPOMATOR CLS IV+ Lead Making Machine* Applicator 466468-1 (Request Catalog 82659)
*Requires applicators. For part
numbers, call Technical Support.
Material (RoHS Compliant)
UL94V-2 rated, nylon, natural color
Keying Plug
Part No. 640254-1
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Keying Pin
Part No. 640255-1
59
Housings
.660
[16.76]
.100
[2.54]
.019
[0.48]
.250
[6.35]
12223 4
.156
[3.96]
Typ.
.076
[1.93]
Typ.
A
.097
[2.46]
.037
[0.93]
Ref.
12223 4
.660
[16.76]
.250
[6.35]
.100
[2.54]
.156
[3.96]
Typ.
.076
[1.93]
Typ.
A
.037
[0.93]
.097
[2.46]
Ref.
12223 4
.660
[16.76]
.250
[6.35]
.156
[3.96]
Typ.
.076
[1.93]
A
Typ.
.060
[1.52]
Material (RoHS Compliant)
UL94V-0 rated, nylon, white
Notes:
1. Accepts either .045 [1.14] square or round posts. Housings mate with flat and friction lock headers, or staked posts on .156 [3.96] centers.
2. Housings without ramp, with
polarizing tab, available upon request. Minimums may apply.
3. Recommend contact:
Part No. 640252 for 1 thru 12 positions; Part No. 350980 for 13 thru 24 positions; Part No. 770476 for 1 thru 24 positions.
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
SL-156 Housings—Wire-to-Board
(A) With Locking Ramp/With Polarizing Tabs
SL-156
.156 [3.96]
For contacts, see page 59.
For mateability options, see matrix on page 58.
For mating half visuals, for connectors with locking ramp, see pages 46, 47, 48, 50 and 52, (49 and 51 Front Bend Headers only.)
For mating half visuals, for connectors without lock­ing ramp, see pages 46 thru 52.
(B) With Locking Ramp/Without Polarizing Tabs
(C) Without Locking Ramp/Without PolarizingTabs
Note: Dim. A = 0.156 (No. of Positions – 1) 0.152
No. of
Positions*
Housing Description
Part Numbers*
2–24 A With Locking Ramp and Polarizing Tabs 770849
1–24
B With Locking Ramp and without Polarizing Tabs 640250 C Without Locking Ramp or Polarizing Tabs 640251
*Base Part Number Prefixes and Suffixes indicate number of contact positions, e.g. 2 Position = 0-xxxxxx-2 and
12 Position = 1-xxxxxx-2.
Note: Housings not for use with LID Contacts. Shown on page 62.
60
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Housings
.078
[1.98]
.105
[2.67]
PC Board 
Posts
.156
[3.96]
1234 78910
123478910
[4.14
.163
+ .005 – .000
+ 0.13 – 0.00
.052
[1.32 ]
± .002
± 0.05
B
.105
[2.67]
Latch Cutout
.015
[0.38] 4 Plc.
Max.R.
A
.078
[1.98]
Typ.
.156
[3.96]
Typ.
.063
[1.60 ]
± .003
± 0.08
.063
[1.60 ]
± .003
± 0.08
.050
[1.27 ]
± .007
± 0.18
.075
[1.91]
.250
[6.35]
.125
[3.18]
.660
[16.76]
Material (RoHS Compliant)
UL94V-2 rated, nylon, white
Mates with .045 square or round staked posts only.
For contacts, see page 59 .
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
SL-156 Housings With Through Board Latch
SL-156
.156 [3.96]
Recommended PC Board Cutout
No. of
Pos.
2
3
4
5
6
7
8
9
10
AB
.312
7.92
.468
11.89
.624
15.85
.780
19.81
.936
23.77
1.092
27.74
1.248
31.70
1.404 1.092
35.66 27.74
1.560 1.248
39.62 31.70
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Note: Not for use with LID Contacts. Shown on page 62.
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
for .062 [1.57] Thick PC Board
Dimensions
Latch Location Part
Centered Between Pos. Number
1 and 2 1-770894-21
1 and 2 1-770894-31
2 and 3 1-770894-41
2 and 3 1-770894-51
3 and 4 1-770894-61
3 and 4 1-770894-71
4 and 5 1-770894-81
1 and 2 & 8 and 9 1-770894-91
1 and 2 & 9 and 10 1-770894-01
61
.054
[1.37]
.095
[2.41]
Typ.
.156
[3.96]
Typ.
.054
[1.37]
Typ.
.0365
[.927]
Ref.
.100
[2.54]
.250
[6.35]
.660
[16.76]
A
SL-156
.156 [3.96]
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
SL-156 Housings and Contacts for Large Insulation Diameter (LID) Wire
Housings
Material (RoHS Compliant)
UL 94V-0 rated, nylon, white
Notes:
1. Accepts Standard and LID contacts.
2. Larger opening in housings
eases contact insertion when using wires that have large insulation diameters (.100-.112 [2.54-2.84]).
3. Housings are not End-to-End
stackable.
For mateability options, see matrix on page 58.
For mating half visuals, for connectors with locking ramp, see pages 46, 47, 48, 50 and 52, (49 and 51 Front Bend Headers only.)
For mating half visuals, for connectors without locking ramp, see pages 46 thru 52.
Contacts
Material and Finish
.012 [0.3] bright tin plated phosphor bronze; .012 [0.3] phosphor bronze with .000030 [0.00076] gold over nickel (see chart)
All tin-plated contacts are
post lubricated to resist fretting corrosion
Maximum insulation
diameter is .112 [2.85]
Wire range is 18-24 AWG
[0.9-0.2 mm 16 AWG [1.29-1.42 mm (2550-2800 CMA)
Product Specifications
108-1049-1 and 108-1049-2
Application Specification
114-1021
Application Tooling
Extraction Tool Part No. 90471-1
Loose Piece Contacts
PRO-CRIMPER II Hand Tool Part No. 91368-1 [18-24 AWG] Part No. 91369-1 [16 AWG] (For field service use only.) For CERTI-CRIMP hand tool, contact Technical Support.
Strip Contacts
AMP-O-LECTRIC Model “G” Termination Machine* Applicator 1385048-3 [18-24 AWG] Applicator 1385219-3 [16 AWG]
AMP-O-LECTRIC Model “K” Termination Machine* Applicator 1385048-2 [18-24 AWG] Applicator 1385219-2 [16 AWG]
62
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
2
] and a limited
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Note: Dim. A = 0.156 (No. of Positions – 1) 0.19
No. of
Positions*
1-24
2–24
*Base Part Number Prefixes and Suffixes indicate number of contact positions, e.g. 2 Position = 0-xxxxxx-2 and
12 Position = 1-xxxxxx-2.
.112 [2.84] .108 [2.74]
2
]
Wire
Size
18-24 AWG
16 AWG Phosphor
(2550-2800 CMA only) Bronze
*Large Insulation Diameter (.100-.112 [2.54-2.84]) Notes: 1. For information on application tooling, call Technical Support.
2. Can not be used with Standard SL-156 Housings, must be used with LID Housings only.
*For additional part numbers and
information contact Technical Support.
Description
Without Locking Ramp
or Polarizing Tabs
With Locking Ramp and 647401
without Polarizing Tabs (shown above)
With Locking Ramp and
Polarizing Tabs
.160
[4.06]
.524
[13.30]
.143
Hooded (Dual Wipe)
(10 Amp Max. Current Rating)
Material Plating
Phosphor
Bronze
Tin 647406-1 647409-1
Gold 647406-2 647409-2
RoHS Compliant 3-647406-1 3-647409-1
Tin 647466-1 647485-1
Gold 647466-2 647485-2
RoHS Compliant 3-647466-1 3-647485-1
Part Numbers*
Housings
with Larger Openings
for Oversize Wire
647400
647402
Part Numbers
For LID* Wire
Strip Loose Piece
R
R
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
AMP Economy Power (EP) Wire-to-Board Connector System
Product Facts
.156 [3.96], .200 [5.08] and
.312 [7.92] centerline
Wire-to-board connectors
comprised of plug housings, receptacle contacts for discrete wire, and mating post headers
Hooded contact designed to
accept wire with insulation diameters up to .118 [3.00]
Positive locking feature
built into header back wall
Locking mechanism on
connector housing maximizes retention
Number of positions: 1 to 11
for .156 [3.96] centerline; 2 to 12 for .200 [5.08] centerline; and 2 to 5 for .312 [7.92] centerline
Straight, through-hole
headers
Positive latch design for
easier mating and unmating
Polarization tabs help
prevent post misalignment and mismating
Low-profile mating height of
.641 [16.3] for 2 to 11 positions
Straight headers are end-to-
end stackable to conserve PCB space
Header packaging: bulk
pack and tube loaded
Plug housings and post
headers intermateable with JST VH connectors
Directive 2002/95/EC (RoHS
Compliant
Recognized under the
Component Program of Underwriters Laboratories Inc., File No. E28476
Certified by Canadian
Standards Association, File No. LR 7189
Applications
Household appliances,
garage door openers,
AMP Economy Power (EP) Connectors are designed for secondary power circuit applications. They consist of wire-to-pc board plug housings (for receptacle contacts) and mating post headers. Three contact centerline spacings are available: .156 [3.96], .200 [5.08] and .312 [7.92].
During mating, the positive locking lever on the outside of the plug housing engages the mating header housing to provide for greater retention. This helps maintain reliable connections, when other non-locking type connec­tors could vibrate apart. This same locking lever must be depressed to unmate the connectors.
The locking mechanism is also located high enough to help avoid interference with pc board clear plastic coating (potting), which is a common treatment for many home appliances.
Headers with .156 [3.96] centerline are offered in 2 through 11 positions; 2 through 12 positions for .200 [5.08] centerline; and .312 [7.92] centerline are available in 2 through 5 positions. Both versions are provided in bulk pack or in tubes for automatic machines.
The slim, straight, post headers are stackable end­to-end for greater flexibility when designing pc board configurations.
The mating height of a low-profile plug and vertical header is .642 [16.3]; even the 1-position high-profile style measures only .732 [18.6] above the pc board. Compact dimensions like these are well suited for most applications in con­fined spaces.
Performance Characteristics
Voltage Rating — 250 VAC Current Rating — 7.5 amp max. (2 to
11 pos.), 8 amp max. (1 pos.) Low Level Overall Resistance
Initial — 10 mmax. Final — 20 mmax. Dielectric Withstanding Voltage
1.5 kV AC, 1 min. Insulation Resistance
Initial — 1000 Mmin. Final — 500 Mmin.
Durability — 50 mating and unmating cycles
Operating Temperature — -13˚F to +221˚F [-25°C to +105°C]
Wire Size Range — 18-22 AWG [0.89-0.30 mm2]
Insulation Diameter — .118 [3.00] max.
Technical Documents
Product Specification
108-5609
Application Specification
114-5253
Instruction Sheet
411-5899
power supplies, power connections, or other areas requiring additional connector retention
63
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
AMP EP
.156 [3.96], .200 [5.08] and .312 [7.92]
Contacts and Plug
.083
[2.11]
.055
[1.40]
.08
[2.1
.362
[9.19]
.382
[9.70]
.154 [3.91]
.039 [1.00]
.524
[13.31]
.284
[7.21]
.224
[5.69]
.156
[3.96]
.150
[3.81]
(3-11 Pos.)
.295 [7.49]
.039
[1.00]
.059
[1.50]
A
(2 Pos.)
.142 [3.61]
Section X-X
Circuit No. 1
Housings, Low-Profile
Crimp, Snap-in Receptacle Contacts
Material and Finish (RoHS Compliant)
See chart.
Related Product Data
Plug Housings — Pages 64, 67 and 69
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
AMP Economy Power (EP) Wire-to-Board Connector System (Continued)
AMP EP
.156 [3.96]
Plug Housings, Low-Profile
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
natural color Note: Alternate colors available upon request. Minimums may apply. Please contact product engineer or product manager for details.
Related Product Data
Contacts — see above Mating Post Headers — Pages 65
and 66
Wire Size
Range
AWG mm
18–22 0.89-0.30
* For 18–20 AWG, use Straight Action Hand Tool (SAHT) Part Number 91579-1.
Wire Material
Insulation and
2 Diameter Finish
Phos. Brz.,
.067-.118
1.70-3.00
Pre-Tin
Brass,
Pre-Tin
1123721-1 1318912-1*
1123721-2
Part
Number
Strip Loose Lead Maker Form Piece Base Part No.
AMPOMATOR
1385286-1 1385286-2 1385286-3
Applicator Part Number
CLS IV+
356500
AMP-O-LECTRIC
Terminator
Model K Model G Part No. Part No.
1-471273-3 354500-1
Number of Dimension Part
Positions A Number
2 .310 [ 7.86] 1-1123722-2 3 .465 [11.82] 1-1123722-3
4.621 [15.78] 1-1123722-4
5.777 [19.74] 1-1123722-5 6 .933 [23.70] 1-1123722-6 7 1.089 [27.66] 1-1123722-7 8 1.245 [31.62] 1-1123722-8
9 1.401 [35.58] 1-1123722-9 10 1.557 [39.54] 1-1123722-0 11 1.713 [43.50] 1-1123722-1 12 1.878 [47.70] 1-647690-2*
64
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
* Consult Product Drawing for dimensional detail.
Post No. 1
.028 [0.7]
.244 [6.2]
.118 [3.0]
.146 [3.7]
.303 [7.7]
.077 [1.95]
.045
[1.14]
Sq. Post
.077 [1.95]
.156
[3.96]
Centerline
.268
[6.8]
.335
[8.5]
A
A
.339
[8.60]
.272
[6.90]
.020
[0.50]
.126
[3.20]
.142
[3.60]
.323
[8.20]
.339
[8.60]
.370
[9.40]
.126
± .004
[3.20
± 0.10
]
.079
± .004
[2.00
± 0.10
]
.045
[1.14]
Ref.
.156
[3.96]
.045
[1.14]
Post No. 1
Sq. Post
Edge of Board
.350
[8.89]
Ø .065/.069
[1.65/1.75]
Typ.
.156
[3.96]
MTA, CST-100 II, SL-156 and
Edge of Board
.190 [4.82]
.125 [3.18]
Typ.
.156 [3.96]
.069/.065
[1.75/1.65]
.066/.062
[1.68/1.57]
Typ.
.078 [1.98]
Recommended Mounting Hole Pattern
for .063 [1.6] Thick PC Board
AMP Economy Power (EP) Connectors
AMP Economy Power (EP) Wire-to-Board Connector System (Continued)
Straight and Right-Angle Low-Profile Post Headers
.156 [3.96] Centerline
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated natural
color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Post — Tin-plated brass
Related Product Data
Mating Plug Housings — Page 64
Straight
Number of Dimension
Positions A
Bulk Pack Tube Loaded (Pcs. per Tube) Bulk Pack with Pegs
2 .310 [ 7.86] 1-1123723-2 1-1318300-2 (61) 1744057-2
3 .465 [11.82] 1-1123723-3 1-1318300-3 (40) 1744057-3
4.621 [15.78] 1-1123723-4 1-1318300-4 (30) 1744057-4
5.777 [19.74] 1-1123723-5 1-1318300-5 (24) 1744057-5
6 .933 [23.70] 1-1123723-6 1-1318300-6 (20) 1744057-6
7 1.089 [27.66] 1-1123723-7 1-1318300-7 (17) 1744057-7
8 1.245 [31.62] 1-1123723-8 1-1318300-8 (15) 1744057-8
9 1.401 [35.58] 1-1123723-9 1-1318300-9 (13) 1744057-9 10 1.557 [39.54] 1-1123723-0 1-1318300-0 (12) 1-1744057-0 11 1.713 [43.50] 1-1123723-1 1-1318300-1 (11) 1-1744057-1 12 1.871 [47.52] 1-647689-2* 1-1744057-2
* Consult Product Drawing for dimensional detail.
Part Number
AMP EP
.156 [3.96]
.156 [3.96] Centerline
Right-Angle
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
natural color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Post — Tin-plated brass
Recommended
PC Board Layout
Related Product Data
Mating Plug Housings — Page 64
Number of Dimension
Positions A
2 .312 [ 7.92] 647676-2
3 .468 [11.88] 647676-3
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
4.624 [15.84] 647676-4
5.780 [19.80] 647676-5
6 .935 [23.76] 647676-6
7 1.091 [27.72] 647676-7
8 1.247 [31.68] 647676-8
9 1.403 [35.64] 647676-9 10 1.559 [39.60] 1-647676-0 11 1.715 [43.56] 1-647676-1 12 1.871 [47.52] 1-647676-2
Part Number
65
A
.339
[8.60]
Edge of Board
.575
[14.60]
.156
[3.96]
Typ.
.045
[1.14]
Sq. Post
Typ.
.059
[1.51]
.323
[8.21]
.156
[3.96]
.225
[5.72]
Ø .065/.069
[1.65/1.75]
.190
[4.82]
.303
[7.70]
.370
[9.40]
.145
[3.69]
Post No. 1
A
.339
[8.60]
Edge of Board
.617
[15.68]
.059
[1.51]
.323
[8.21]
.142
[3.60]
.350
[8.89]
Ø .065/.069
[1.65/1.75]
.190
[4.82]
.303
[7.70]
.370
[9.40]
Post No. 1
.156
[3.96]
Typ.
Typ.
.156
[3.96]
.045
[1.14]
Sq. Post
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
AMP Economy Power (EP) Wire-to-Board Connector System (Continued)
AMP EP
.156 [3.96]
Straight and Right-Angle Low-Profile Post Headers, High Temperature
.156 [3.96] Centerline
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
high temperature, natural color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Post — Tin-plated brass
Related Product Data
Mating Plug Housings — Page 64
Straight
Number of Dimension
Positions A
2 .312 [ 7.92] 1744055-2
3 .468 [11.88] 1744055-3
4.624 [15.84] 1744055-4
5 .780 [19.80] 1744055-5
6 .935 [23.76] 1744055-6
7 1.091 [27.72] 1744055-7
8 1.247 [31.68] 1744055-8
9 1.403 [35.64] 1744055-9 10 1.559 [39.60] 1-1744055-0 11 1.715 [43.56] 1-1744055-1
Maximum Temperature Rating: 280°C
Recommended
PC Board Layout
Part Number
Right-Angle
.156 [3.96] Centerline
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
high temperature, natural color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Post — Tin-plated brass
Related Product Data
Mating Plug Housings — Page 64
Number of Dimension
Positions A
2 .312 [ 7.92] 1744056-2
3 .468 [11.88] 1744056-3
4.624 [15.84] 1744056-4
5.780 [19.80] 1744056-5
6 .935 [23.76] 1744056-6
7 1.091 [27.72] 1744056-7
8 1.247 [31.68] 1744056-8
9 1.403 [35.64] 1744056-9 10 1.559 [39.60] 1-1744056-0 11 1.715 [43.56] 1-1744056-1 12 1.871 [47.52] 1-1744056-2
66
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Part Number
Recommended
PC Board Layout
Plug Housings and
A
.406
[10.30]
.263
[8.88]
.051
[1.30]
.200
[5.08]
.051
[1.30]
.053
[1.35]
Typ.
Typ.
Circuit No. 1
A
.339
[8.60]
.575
[14.60]
.200
[5.08]
Typ.
Typ.
.323
[8.21]
.200
[5.08]
Ø .065/.069
[1.65/1.75]
.190
[4.82]
.303
[7.70]
.370
[9.40]
.059
[1.51]
.146
[3.70]
Post No. 1
Recommended PC Board Layout
Sq. Post
.045
[1.14]
A
.339
[8.60]
Edge of Board
.059
[1.51]
.323
[8.21]
.142
[3.60]
.669
[17.00]
Ø .065/.069
[1.65/1.75]
.190
[4.82]
.303
[7.70]
.370
[9.40]
Post
No. 1
Ref.
Max.
2 Plcs.
.080
[2.02]
Sq. Post
.045
[1.14]
.200
[5.08]
Typ.
Post Headers
Plug Housings .200 [5.08] Centerline
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
AMP Economy Power (EP) Wire-to-Board Connector System (Continued)
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
natural color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Related Product Data
Contacts — Page 64 Mating Post Headers — See below
Post Headers .200 [5.08] Centerline
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
natural color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details. Post—Tin-plated brass
Number of Dimension Part
Positions A Number
2 .353 [ 8.98] 1744036-2
3 .553 [14.06] 1744036-3
4 .753 [19.14] 1744036-4
5.953 [24.22] 1744036-5
6 1.153 [29.30] 1744036-6
7 1.353 [34.38] 1744036-7
8 1.553 [39.46] 1744036-8
9 1.753 [44.54] 1744036-9 10 1.953 [49.62] 1-1744036-0 11 2.153 [54.70] 1-1744036-1 12 2.353 [59.78] 1-1744036-2
AMP EP
.200 [5.08]
Related Product Data
Mating Plug Housings — See above
Recommended PC Board Layout
Number of Dimension
Positions A
Straight Right-Angle
2 .302 [ 7.68] 1744037-2 1744048-2
3 .502 [12.76] 1744037-3 1744048-3
4 .702 [17.84] 1744037-4 1744048-4
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
5 .902 [22.92] 1744037-5 1744048-5
6 1.102 [28.00] 1744037-6 1744048-6
7 1.302 [33.08] 1744037-7 1744048-7
8 1.502 [38.16] 1744037-8 1744048-8
9 1.702 [43.24] 1744037-9 1744048-9 10 1.902 [48.32] 1-1744037-0 1-1744048-0 11 2.102 [53.40] 1-1744037-1 1-1744048-1 12 2.302 [58.48] 1-1744037-2 1-1744048-2
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Part Number
67
Straight Post Headers,
A
.077 [1.95]
.028 [0.7]
.312 [7.92]
Centerline
.077 [1.95]
.045 Sq. Post [1.14]
.244 [6.2]
.118 [3.0]
.146 [3.7]
.303 [7.7]
.312 [7.92] Centerline
Recommended PC Board Layout
Acceptable Board Thickness
.062 [1.57]
.063 +.004/-0 Dia. Punched Hole
[1.60 +0.1/-0]
.065 +.004/-0 Dia. Drilled Hole [1.65 +0.1/-0]
.335
[8.5]
.268
[6.8]
Post No. 1
Mating Height
.642 [16.3]
Low-Profile
.312 [7.92] Centerline
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated natural
color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Post — Tin-plated brass
Related Product Data
Mating Plug Housings — Page 64
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
AMP Economy Power (EP) Wire-to-Board Connector System (Continued)
Number of Dimension Part Number
Positions A Bulk Pack Tube Loaded (Pcs. per Tube)
2 .465 [11.82] 1-1123724-2 1-1318301-2 (40)
3.777 [19.74] 1-1123724-3 1-1318301-3 (24)
4 1.089 [27.66] 1-1123724-4 1-1318301-4 (17)
5 1.401 [35.58] 1-1123724-5 1-1318301-5 (13)
AMP EP
.312 [7.92]
Mating Height (Low-Profile)
68
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Plug Housing and
.571
[14.5]
.244 [6.2]
.169 [4.3]
.224 [5.7]
.039 [1.0]
.150 [3.8]
.207 [5.3]
Section X-X
Recommended PC Board Layout
Acceptable Board Thickness
.062 [1.57]
Soldering Side
Component Mounting Side
Section X-X
.528
[13.4]
.327 Max.
[8.3]
Urethane Coating Area
.337 [8.55]
.146 [3.7]
.118 [3.0]
.079-.032±.004
[2-0.8±0.1]
.079-.051+.004/-0
[2-1.3+0.1/-0]
.079-.142±.004
[2-3.6±0.1]
.315±.004 [8.0±0.1]
.158±.004 [4.0±0.1]
.128 [3.25]
.189 [4.8]
.045 [1.14] Sq. Post
PC Board
Eyelet
.118
[3.0]
.347
[8.8]
.252
[6.4]
.154 [3.9] Max. Dia.
.197 [5.0]
Max. Dia.
.063 +.004/-0 Dia. Punched Hole [1.60 +0.1/-0]
.065 +.004/-0 Dia. Drilled Hole [1.65 +0.1/-0]
Mating Height
.732 [18.6]
Potting Height
.327 [8.3] Max.
Retention Lock
Post Header, High-Profile
1 Position Plug Housing Part Number 1-1123823-1
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
natural color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Related Product Data
Contacts — Page 64 Mating Post Header — See below
1 Position Post Header, Straight Part Numbers 1-1123824-1 (Bulk Pack) 1-1318831-1 (Tube Loaded, 55 pcs. per Tube)
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
AMP Economy Power (EP) Wire-to-Board Connector System (Continued)
Material and Finish (RoHS Compliant)
Housing — UL 94V-0 rated nylon,
natural color Note: Alternate colors available upon
request. Minimums may apply. Please contact product engineer or product manager for details.
Post — Tin-plated brass
Related Product Data
Mating Plug Housing — See above
Mating Height (High-Profile)
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
69
AMP EP
High-Profile 1 Position
.400-.800†
[10.16-20.32]
Feed-Thru NotchDead-End Notch
.036-.046 Standard
(.046-.052 Allowable for  26-28 AWG Wire Only)
.280-.450†
[7.112-11.43]
.036-.046 Standard (.046-.052 Allowable for 26-28 AWG Wire Only)
.500-1.000†
[12.70-25.40]
Feed-Thru NotchFlush-Mount Notch
.400-.600†
[10.16-15.24]
.062-.080
[1.57-2.03]
.062-.080
[1.57-2.03]
.064 [1.63] Typ. (Max.) After Notching
.050 [1.27] Dia. (Max.) For Mass Terminating
.100
[2.54] (Typ.)
Insulation
Conductor
Web
.094 [2.39] Typ. (Max.) After Notching
.070 [1.78] Dia. (Max.) For Mass Terminating
.156
[3.96] (Typ.)
Insulation
Conductor
Web
Ribbon Cable End View
– A –
.010 A
Per Inch of Cable Width
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA Wire Selection
Proper wire selection is critical to the success of a wire-to­board application. The chart identifies wires that have been evaluated and approved by the product engineering section. If you plan to use a wire not on the approved list, please submit a sample 12" length of wire to Tyco Electronics for evaluation.
AWG Metric Equivalents
18 —0.8–0.9 mm 20 —0.5–0.6 mm 22 —0.3 –0.4 mm 24 —0.2 mm 26 —0.12–0.15 mm 28 —0.08–0.09 mm
2
2
2
2
2
2
Product Specifications
108-1050 —MTA-100 Connectors 108-1050-1—MTA-100 Posted
Connectors 108-1051 —MTA-156 Connectors 108-1219 —MTA-156 Quad Connector
System
108-1065—MTA-156 Posted
Connectors
108-1058 —MTA-156 Card Edge
Connectors
Application Specifications
114-1019 —MTA-100 Connectors 114-1020 —MTA-156 Connectors 114-1031 —MTA-100 Ribbon Cable
114-1032 —MTA-156 Ribbon Cable
114-1048 —MTA-156 Quad Connector
Connector Assembly
Connector Assembly
MTA Connectors Approved Wire Listing
MTA-100 Connectors Wall Approved Wire AWG
UL 1007 PVC Insulation .015[0.381] 22, 24, 26, 28 UL 1061 Semi-Rigid PVC Insulation .009[0.229] 22, 24, 26, 28 UL 1095 Semi-Rigid PVC Insulation .012[0.305] 24 UL 1371 TEFLON Insulation — TFE .006[0.152] 22, 26 UL 1429 Irradiated PVC — X.L.P.V.C. .010[0.254] 22, 24, 26, 28 UL 2464 PVC .013[0.330] 24 UL 3265 Irradiated Polyethylene — X.L.P.E. .010[0.254] 22, 24 UL 3266 Irradiated Polyethylene — X.L.P.E. .015[0.381] 22, 24 MIL-W-16878, Type B-PVC Insulation .010[0.254] 22 UL 1213 TEFLON Insulation—T.F.E. .010[0.254] 22
MTA-156 Connectors
UL 1007 PVC Insulation .015[0.381] 18, 20, 22, 24 UL 1061 Semi-Rigid PVC Insulation .009[0.229] 18, 20, 22, 24 UL 1180 TEFLON Insulation — T.F.E. .015[0.381] 22 UL 1213 TEFLON Insulation — T.F.E. 010[0.254] 18, 22, 24 UL 1316 PVC/Nylon Wall .015[0.381] 18, 22 UL 1429 Irradiated PVC — X.L.P.V.C. .010[0.254] 18, 20, 22, 24 UL 1430 Irradiated PVC — X.L.P.V.C. .015[0.381] 18, 20, 22, 24 UL 1569 PVC .015[0.381] 18 UL 3265 Irradiated Polyethylene — X.L.P.E. .010[0.254] 22 UL 3266 Irradiated Polyethylene — X.L.P.E. .015[0.381] 18, 20, 22, 24
Note: When selecting approved wire styles noted on this list, the MTA Application Specifications guidelines must be
followed. Also, due to wire variations in insulation wall thickness, hardness and wire stranding we would recom­mend evaluating the wire selected before final application approval.
TEFLON is a trademark of E.I. DuPont de Nemours and Company.
MTA-100 Ribbon Cable Preparation MTA-156 Ribbon Cable Preparation
MTA
Wire Selection
70
† The dimensions shown represent the recommended minimum and maximum for notches;
the actual dimension will depend on your application requirements.
Notes:
1. Cable shall be notched, as indicated in the individual ribbon cable connector assembly drawing, according to the requirements specified in these figures. Conductor shall not be exposed after notching, nor shall individual wire stands be cut or nicked.
2. U.L. Style #2651 ribbon cable is approved for use with MTA-100 and MTA-156 connectors per Application Specification 114-1031 and 114-1032.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Notes:
1. For MTA Cable Assemblies Contact US Engineering Cable Assembly Group.
2. For IDC Cable, see pages 71 thru 74.
(Ends of the cable shall be prepared as indicated in this figure)
Ribbon Cable
Cable Edge-to-End Alignment
Product Facts
R
Compatible with a variety
of Insulation Displacement Connectors
Available on .025 [0.63],
.0394 [1.00], .050 [1.27], .100 [2.54] and .156 [3.96] centerline
Color code edge mark on
conductor #1
Gray flame retardant
flexible PVC insulation
Insulation rated for
temperature of
-20°C to +105°C
Recognized under the
Component Program of Underwriters Laboratories Inc., File No. E53793
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
IDC Ribbon Cable
Product Specifications
Voltage Rating — 30 VAC Component Recognized by UL to
US and Canadian Standards
AWM Style 2651
Tyco Electronics Corporation has an expanding array of MADISON CABLE planar PVC insulated product designed for compatibility with a variety of Insulation Displacement Connectors. AMP IDC terminations offer a quick, reliable, cost-effec­tive cabling system which can be automated.
The .100 [2.54] centerline cable is available in 28 to 22 AWG, either as tinned or as overcoated tinned wire, in 2 to 28 conductors.
The .156 [3.96] centerline is available in 22 AWG and 18 AWG, either as tinned or overcoated tinned, in 2 to 24 conductors.
.050 [1.27] Centerline, IDC Ribbon Cable
Sizes 26 AWG, 7/34 Tinned copper, PVC
insulation (9 – 64 conductors), 500-ft reels (Base AMP Part Number 57034)
28 AWG, 7/36 Tinned copper, PVC insulation (9 – 64 conductors), 100-ft reels (Base AMP Part Number 57040) and 500-ft reels (Base AMP Part Number 971111)
30 AWG, Other conductor counts avail­able on request. For ordering informa­tion, call Toll-Free: 1-877-623-4766 or visit: http://www.madisoncable.com/
fsproducts.htm
IDC Ribbon Cable is produced to tighter stan­dards than usually required for high yield insulation displacement terminations. The extra precision offers uncomplicated operation in fully automatic stripping, notching and termination equipment.
IDC
Ribbon Cable
71
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
.100 [2.54] Centerline, IDC Ribbon Cable, PVC Insulation
IDC
Ribbon Cable
Product Specifications
Voltage Rating — 300 Volts UL Recognized — AWM Style 2651 CSA — Available on request
Edge Mark
No. of
Conductors
28 AWG 7/32 Tinned Copper
2 0.100 [2.54] 0.200 [5.08] 0.044 [1.12] 02WFY00006P
5 0.400 [10.16] 0.500 [12.70] 0.044 [1.12] 05WFY00006P 10 0.900 [22.86] 1.000 [25.40] 0.044 [1.12] 10WFY00006P 15 1.400 [35.56] 1.500 [38.10] 0.044 [1.12] 15WFY00006P 20 1.900 [48.26] 2.000 [50.80] 0.044 [1.12] 20WFY00006P 25 2.400 [60.96] 2.500 [63.50] 0.044 [1.12] 25WFY00006P 28 2.700 [68.58] 2.800 [71.12] 0.044 [1.12] 28WFY00006P
26 AWG 7/34 Tinned Copper
2 0.100 [2.54] 0.200 [6.08] 0.039 [.99] 02WEY00008P
5 0.400 [10.16] 0.500 [12.70] 0.039 [.99] 05WEY00004P 10 0.900 [22.86] 1.000 [25.40] 0.039 [.99] 10WEY00012P 15 1.400 [35.56] 1.500 [38.10] 0.039 [.99] 15WEY00002P 20 1.900 [48.26] 2.000 [50.80] 0.039 [.99] 20WEY00008P 25 2.400 [60.96] 2.500 [63.50] 0.039 [.99] 25WEY00008P 28 2.700 [68.58] 2.800 [71.12] 0.039 [.99] 28WEY00008P
26 AWG 7/34 Overcoated Tinned Copper
2 0.100 [2.54] 0.200 [5.08] 0.039 [.99] 02WEY00007P
5 0.400 [10.16] 0.500 [12.70] 0.039 [.99] 05WEY00007P 10 0.900 [22.86] 1.000 [25.40] 0.039 [.99] 10WEY00007P 15 1.400 [35.56] 1.500 [38.10] 0.039 [.99] 15WEY00007P 20 1.900 [48.26] 2.000 [50.80] 0.039 [.99] 20WEY00007P 25 2.400 [60.96] 2.500 [63.50] 0.039 [.99] 25WEY00007P 28 2.700 [68.58] 2.800 [71.12] 0.039 [.99] 28WEY00007P
Other Conductor Counts Available on Request.
ABC
Contact MADISON CABLE (1-877-MADISON), a Division of Tyco Electronics Corporation, for engineering questions or for order placement of this cable.
Dimensions
Part
Number
B
A
.100
[2.54]
Typ.
No. of
Conductors
24 AWG 7/32 Overcoated Tinned Copper
2 0.100 [2.54] 0.200 [5.08] 0.044 [1.12] 02WFY00007P
5 0.400 [10.16] 0.500 [12.70] 0.044 [1.12] 05WFY00007P 10 0.900 [22.86] 1.000 [25.40] 0.044 [1.12] 10WFY00007P 15 1.400 [35.56] 1.500 [38.10] 0.044 [1.12] 15WFY00007P 20 1.900 [48.26] 2.000 [50.80] 0.044 [1.12] 20WFY00007P 25 2.400 [60.96] 2.500 [63.50] 0.044 [1.12] 25WFY00007P 28 2.700 [68.58] 2.800 [71.12] 0.044 [1.12] 28WFY00007P
22 AWG 7/30 Tinned Copper
2 0.100 [2.54] 0.200 [5.08] 0.051 [1.30] 02WGY00001P
5 0.400 [10.16] 0.500 [12.70] 0.051 [1.30] 05WGY00006P 10 0.900 [22.86[ 1.000 [25.40] 0.051 [1.30] 10WGY00002P 15 1.400 [35.56] 1.500 [38.10] 0.051 [1.30] 15WGY00006P 20 1.900 [48.26] 2.000 [50.80] 0.051 [1.30] 20WGY00006P 25 2.400 [60.96] 2.500 [63.50] 0.051 [1.30] 25WGY00006P 28 2.700 [68.58] 2.800 [71.12] 0.051 [1.30] 28WGY00006P
A BC
.050 [1.27] Typ.
.010 [0.25]
Insulation — Gray Flame Retardant Flexible PVC .007 [0.17] Minimum Insulation Thickness Temperature Rating — -20°C to +105°C Flammability — UL: VW1
Dimensions
C
Part
Number
72
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
.156 [3.96] Centerline, Flat Ribbon Cable, PVC Insulation
Product Specifications
Voltage Rating — 300 Volts UL Recognized — AWM Style 2651 CSA — Available on request
B
A
Edge Mark
No. of
Conductors
22 AWG 7/30 Tinned Copper
2 0.156 [3.96] 0.312 [7.92] 0.051 [1.30] 02WGY00008P
5 0.624 [15.85] 0.780 [19.81] 0.051 [1.30] 05WGY00008P 10 1.404 [35.66] 1.560 [39.62] 0.051 [1.30] 10WGY00008P 15 2.184 [55.47] 2.340 [59.44] 0.051 [1.30] 15WGY00008P 20 2.964 [75.29] 3.120 [79.25] 0.051 [1.30] 20WGY00008P 24 3.588 [91.14] 3.744 [95.10] 0.051 [1.30] 24WGY00008P
18 AWG 7/26 Tinned Copper
2 0.156 [3.96] 0.312 [7.92] 0.068 [1.73] 02WJY000001P
5 0.624 [15.85] 0.780 [19.81] 0.068 [1.73] 05WJY000010P 10 1.404 [35.66] 1.560 [39.62] 0.068 [1.73] 10WJY000010P 15 2.184 [55.47] 2.340 [59.44] 0.068 [1.73] 15WJY000010P 20 2.964 [75.29] 3.120 [79.25] 0.068 [1.73] 20WJY000010P 24 3.588 [91.14] 3.744 [95.10] 0.068 [1.73] 24WJY000010P
Other Conductor Counts Available on Request.
ABC
.156
[3.96]
Typ.
Dimensions
Part
Number
.078 [1.98] Typ.
C
.010
[0.25]
Insulation — Gray Flame Retardant Flexible PVC .007 [0.17] Minimum Insulation Thickness Temperature Rating — –20°C to +105°C Flammability — UL: VW1
Contact MADISON CABLE (1-877-MADISON), a Division of Tyco Electronics Corporation, for engineering questions or for order placement of this cable.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
73
IDC
Ribbon Cable
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Prepared IDC Ribbon Cable
IDC
Ribbon Cable
In addition to bulk cable, the US Engineering Cable Assembly Group offers Prepared Cable for the .100 [2.54] and .156 [3.96] cen­terline cables. This can be in the form of prenotched cable on reels or cut-to­length cable segments.
Prenotched 250 foot reels of cable can be produced with notches at varying increments or repeating all along the cable. The maxi­mum width of these cables
is 20 conductor for the .100 [2.54] centerline and 13 conductor for the .156 [3.96] centerline.
Prepared Cable is also available with a Strip and Retain feature allowing the cable assembly to be sol­dered directly to the PC Board. This saves space and cost and reduces spare parts inventory. Strip and Retain on both ends is used in family board appli­cations to maintain the
electrical connection when the PC Board is separated into smaller boards after soldering. Widths are limited to 20 conductors for the .100 [2.54] centerline and 13 conductors for the .156 [3.96] centerline. However, multiple cables can be placed side-by-side in a single connector. For other styles and configurations contact the product engi­neer or product manager.
74
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Insulation Strain Relief
Conductor Insulation will be contained within the confines of the insulation strain relief as indicated
B Min.
A
Top of
Contact
Conductor Bare wires will not be visible beyond back of housing
Centerline of Conductor
Back of Housing
Bare wires will not extend above top of contact
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA Wire Termination Flowchart
Choose the appropriate MTA Connector from the MTA Catalog 82056.
Select the proper wire style and AWG for the chosen MTA Connector (Refer to pages 70-74).
Choose the MTA Termination Tooling (Refer to pages 76-79).
Terminate the Wire-to-MTA Connector per Application Tooling Instruction Sheet.
Inspect the MTA Wire Termination per Application Specification, especially the wire depth. See illustrations: 114-13072 — MTA-50 Connectors, 114-1019 — MTA-100 Connectors, 114-1020—MTA-156 Connectors, Posted Connector, Card Edge, 114-1048 — MTA-156 Quad Connectors, 114-1031 — MTA-100 Ribbon Cable Connector Assembly, and 114-1032 — MTA-156 Ribbon Cable Connector Assembly.
Connector AB
MTA-100
MTA-156
.069–.087 .040
[1.75-2.21] [1.02]
.090–.113 .060
[2.29-2.87] [1.52]
MTA Wire Termination
Flowchart
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Adjust the Termination Tooling (if needed) per Tooling Instruction Sheet (repeat the step above).
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
75
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA Application Tooling Options
Tooling
Application
76
One-At-A-Time Termination Tooling Part Numbers
Interchangeable Head
MTA Connector
Assembly
MTA-50
Closed End
Feed Thru
Closed
MTA-100 58246-3 (Ribbon Cable) Connector
MTA-156 58247-3 (Ribbon Cable) Connector
MTA-156 Closed Card-Edge End
MTA-156 Closed Quad End
End
Feed Thru 58442-1 ——59803-1
Posted
(Closed-End)
Closed
End
Feed Thru 58443-1 ——59804-1
Posted
(Closed-End)
Manual Hand Tool 58074-1
Air Hand Tool 58075-1
Air Bench Mount Tool 58338-1
Electric Bench Machine 931800-1
1583503-1 ——
58246-1 (Standard)*n 58246-2 (Ext Wear)* 933567-1 466728-1 59803-1
58638-1 ——59803-1
58247-1 (Standard)** 58247-2 (Ext Wear) 933568-1 466727-1 59804-1
58082-1 ——59804-1
58061-1 ——567020-1 59839-1
58392-1 ——59804-1
Interchangeable Head and Interchangeable Head and
Loose-Piece Feed Track Tape Feed Track
Air Bench Mount Air Bench Mount
Tool 58338-1 Tool 58338-1
Electric Bench Electric Bench
Machine 931800-1 Machine 931800-1
Note: Max. Insulation Outside Diameter Wire:
.060 [1.52] for MTA-100 Connectors /.095 [2.41] for MTA-156 Connectors
Special
Applicator
853546-1 & 853542-1
(Base)
853547-1 & 853542-1
(Base)
T-Handle
Maintenance
Tool
Notes:
1. A repair kit consists of a cam,
a feed-slide sub-assembly and a locating pawl. Repair kits can be made available for other inter­changeable heads. Consult Tyco Electronics.
2. Standard modular heads 58246-1 and 58247-1 are recommended for low volume use.
3. Extended wear modular heads 58246-2 and 58247-2 are recommended for high volume use.
4. T-Handle Maintenance Tools are for maintenance (field) use only. They are not rec­ommended for production.
5. Some Manual Hand Tool
Assemblies are available: a. Order 58579-1, comprised
of Head 58246-1 with Manual Hand Tool 58074-1.
b. Order 58580-1, comprised
of Head 58247-1 with Manual Hand Tool 58074-1.
c. Order 58639-1, comprised
of Head 58638-1 with Manual Hand Tool 58074-1.
*Repair Kit 856600-1 **Repair Kit 856600-2
MTA-50 Mass Termination Tooling Part Numbers
Manual Arbor Frame (with slide) Part Number 1583518-1*
Upper Tooling Part Number 1583514-1*
Fixture, Discrete Wire, Closed End Part Number 1583515-1 (28-26 AWG) Part Number 1583515-2 (30-28 AWG)
MTA-100 and MTA-156 Mass Termination Tooling Part Numbers
MTA Connector
Assembly
Closed End ——
MTA-100 58644-2 (Notched Cable) Connector
Feed Thru
Closed End
(Posted)
Feed Thru
(Posted)
Closed End ——
Feed Thru
MTA-156 Connector Card Edge ——
Closed End
(Posted)
Feed Thru
(Posted)
Closed End ——
MTA-156 Quad
Feed Thru —— Tooling Assy ——
2- through 12-positions.††2- through 8-positions.
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
58644-1 (Discrete Wire)
58646-1 (Discrete Wire)
58646-2 (Notched Cable)
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Fixture, Discrete Wire, Feed-Thru Part Number 1583516-1 (28-26 AWG) Part Number 1583516-2 (30-28 AWG)
Fixture, Ribbon Cable, Closed End or Feed-Thru Part Number 1583517-1
*Required, plus appropriate Fixture(s).
Note: Max. Insulation Outside Diameter Wire:
.050 [1.27] for MTA-100 Connectors /.070 [1.78] for MTA-156 Connectors
Interchangeable Head
Part Number Used With
Harness Board Holding Fixture
Part Number
Applicator Tooling
Assembly Assembly
Used With
58242-1
58074-1 (Man Hd Tl)
——
——
58243-1 — 58243-3 58575-1
58635-1 58575-1
58636-1 58575-1
58242-3 58575-1
Manual Bench
Tool 58024-1
and Tooling
Assembly
58039-1
58244-1 — 58244-3 58576-1
††
58074-1 (Man Hd Tl)
††
——
58245-1 — 58245-3 58576-1 59848-1 — 59848-3 58576-1 58009-1
58009-2 58576-1
Manual Bench
Tool 58024-1
and Tooling
Assembly
58040-1
——58010-2 58576-1 ——
58244-1 — 58244-3 58576-1
58245-1 — 58245-3 58576-1
Manual Bench
Tool 58024-1 ——
and Tooling
Assy 58040-1
58024-1 and
58040-1
Interchangeable Head
and Tape Feed Track
Part Number Used With
854175-1 &
854200-1 (Base)
312522-1
——
——
——
854176-1 &
854200-1 (Base)
312522-1
——
——
——
One-At-A-Time Termination Tooling (Typical Tooling Combinations)
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA Application Tooling Options (Continued)
Manual Hand Tool with
Interchangeable Head
Power Units
Manual Hand Tool — Pistol Grip Handle Part No. 58074-1
Easy to use
Ratchet control will not
release the trigger until it is fully bottomed
Head may be rotated for
user convenience
Air Bench Mount Tool with
Interchangeable Head and Loose-Piece Feed Track
Air Hand Tool with
Interchangeable Head
Air Hand Tool — Pistol Grip Pneumatic Handle Part No. 58075-1
Light weight
Operates at air pressure
between 40 and 70 psi [2.76 and 4.83 bar]
Head may be rotated for
user convenience
Air Bench Mount Tool with Interchangeable Head and
Foot Switch
Air Bench Mount Tool — Bench Mount Power Assembly Part No. 58338-1
May be mounted with
interchangeable head pointed up or down
Operated by a foot
switch
Operates at air pressure
between 40 and 70 psi [2.76 and 4.83 bar]
Electric Bench Machine with
Interchangeable Head and
Tape Feed Track
Electric Bench Machine with
Interchangeable Head
Electric Bench Machine — IDC Power Unit Part No. 931800-1
All electric: 120 VAC,
60 Hz, 2 A
Compact, portable and
quiet
Operated by a foot
switch
AMP-O-LECTRIC Bench
Machine with Special Applicator
Interchangeable Heads and Applicators (Refer to page 76 for part numbers.)
Interchangeable Head
Terminates one
unstripped wire per cycle
Aligns and holds the
connector in place for each termination
Automatically advances
the connector after each termination
Interchangeable Head and Loose-Piece Feed Track
No special setup required
Connectors are easily
loaded into feed track
Connectors are fed using
a simple spring-loaded pusher
Interchangeable Head and Tape Feed Track
No special setup required
Tape-mounted connectors
are transferred from prod­uct reel to feed track by simply pulling on the free end of the carrier tape
Connectors are fed using
a simple spring-loaded pusher
T-Handle Maintenance Tool
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Special Applicator
Connectors are easily
hand loaded into feed track
Automatically advances
the connector after each termination
Cannot be cycled until
the connector is properly positioned
77
Application
Tooling
Mass Termination Tooling (Typical Tooling Combinations)
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA Application Tooling Options (Continued)
Tooling
Application
Manual Bench Tool with
Applicator and Holding Fixture
Power Units
Manual Bench Tool — Arbor Frame Assembly Part No. 58024-1
Applicator and holding
fixture can be oriented for operator convenience for closed-end or feed-thru terminations
Ram height (insertion
depth) is easily adjusted
May be bench mounted
Air Harness Tools — Hand-Held Power Unit with Applicator Part No. 58575-1 (MTA-100) Part No. 58576-1 (MTA-156)
Applicator can be rotated
360° for orientation with holding fixture
Insertion depth is easily
adjusted
Operates at air pressure
between 75 and 95 psi [5.17 and 6.55 bar]
Applicators and Notcher Assemblies
Manual Bench Tool with Applicator and Tape Feed Track
Applicator and Holding Fixture
Wires are laced into
plastic combs for mass termination
Trims excess wire for
closed-end terminations
Holding fixture may be
mounted to a harness board
Applicator and Tape Feed Track
Tape-mounted connectors
are transferred from prod­uct reel to feed track by simply pulling on the free end of the carrier tape
Connectors are fed using
a simple spring-loaded pusher
Feed stop easily adjusted
for different connector sizes
Applicator
Air Bench MachineAir Harness Tool with
Air Bench Machine — Pneumatic Unit Part No. 91112-2
Operated by a foot
switch
Operates at air pressure
between 80 and 90 psi [5.52 and 6.21 bar]
Not recommended for
notching cable with more
2700 lb Air Bench Machine with
Ribbon Cable Notcher Assembly
2700 lb Air Bench Machine — Part No. 312522-1
Operated by a foot
switch
Capable of exerting
2,700 lb [12,000 N] of force at minimum 80 psi [5.52 bar] air pressure
May be bench mounted
than 14 conductors
Ribbon Cable Notcher Assembly
Notch cable with up to
28 conductors for .100 centerline, and 24 conductors for .156 centerline
Pressure plate holds
cable in position during notching
Scrap conveniently
removed through a chute with a blast of air from a
Ribbon Cable Notcher
Assembly
built-in air valve
Part Number
854449-2 26-28
854449-4 22-28
854449-3 18-24
Use Adapter 854468-1 when putting Notcher in the AMP-O-LECTRIC Machine. Use Adapter 854468-2 when putting Notcher in the 2700 lb Air Bench Machine.
Wire Size
AWG
Centerline Used With
.100 Manual Bench Tool
2.54 58024-1 .100 Air Bench Machine
2.54 91112-2 2700 lb Bench Machine
.156
3.96
(with Conversion Kit 690675-2)
312522-1
AMP-O-LECTRIC
Bench Machine 1-471273-3
78
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
MTA Application Tooling Options (Continued)
Technical Documents
The following is a list of technical documents covering the installation, operation, adjustment, maintenance and repair of MTA application tooling.
Instruction Sheets (IS) provide instructions for assembling or applying the product. They are intended for the Manufacturing Assembler or Operator.
Customer Manuals (CM) provide complete, detailed instructions on the installation, operation, adjustment, maintenance and repair of complex tools and application machines.
Applicator Instructions (AI) are similar to instruction sheets (which cover products and tools), and provide instructions for installation, adjustment and maintenance of applicators used in auto­matic and semiautomatic machines.
Hand Tools, Power Units & Accessories
Manual Arbor Frame (MTA-50) 1583518-1 IS 408-8812 2700 lb Air Bench Machine 312522-1 CM 409-5843 Upper Tooling (MTA-50) 1583514-1 IS 408-8812 Terminator Assembly, "G" Term 354500-1 CM 409-5842 Manual Arbor Frame Assembly 58024-1 IS 408-6923 AMP-O-LECTRIC Bench Machine 1-471273-3 CM 409-5128
Ribbon Cable Applicator, .100 58039-1 IS 408-6685 Conversion Kit 690675-2 IS 408-8022 Ribbon Cable Applicator, .156 58040-1 IS 408-6701 Base Assembly 853542-1 IS 408-9636 Manual Hand Tool 58074-1 IS 408-6790 Base 854200-1 IS 408-9650 Air Bench Mount Tool 58338-1 IS 408-9393 Adapter (AMP-O-LECTRIC) 854468-1 IS 408-9687 Air Hand Tool (MTA-100) 58575-1 IS 408-4260 Adapter (2700 lb Machine) 854468-2 IS 408-9687 Air Harness Tool (MTA-156) 58576-1 IS 408-4260 Repair Kit 856600-1 IS 408-9745 T-Handle Maintenance Tool (MTA-100) 59803-1 IS 408-7907 Repair Kit 856600-2 IS 408-9745 T-Handle Maintenance Tool (MTA-156) 59804-1 IS 408-7907 Electric Bench Mount Tool 931800-1 CM 409-5746 Air Arbor Frame Assembly 91112-2 IS 408-7763
One-At-A-Time Termination Tooling
Interchangeable Heads Interchangeable Head & Loose Piece Feed Track
1583503-1 IS 408-8801 58247-1 IS 408-6930 933567-1 IS 408-9435 933568-1 IS 408-9466
58246-1 IS 408-6929 58246-2 IS 408-9379 58246-3 IS 408-4147 58442-1 IS 408-9603 58638-1 IS 408-4358
MTA-50 MTA-156 MTA-100 MTA-156
MTA-100
58247-2 IS 408-9380 58247-3 IS 408-4146 58443-1 IS 408-9607 58061-1 IS 408-6794 58082-1 IS 408-6795 58392-1 IS 408-9450
Interchangeable Heads & Tape Feed Track
853546-1 IS 408-9636 853547-1 IS 408-9637
Special Applicators
466728-1 AI 408-8054 466727-1 AI 408-8054
MTA-100 MTA-156
MTA-100 MTA-156
567020-1 AI 408-8069
Mass Termination Tooling
1583515-1 IS 408-8812 58242-1 IS 408-7994 58009-1 IS 408-7995 854175-1 IS 408-9667 1583515-2 IS 408-8812 58242-3 IS 408-7994 58009-2 IS 408-7995 1583516-1 IS 408-8812 58243-1 IS 408-7994 58010-2 IS 408-7995 MTA-156 1583516-2 IS 408-8812 58635-1 IS 408-7994 58244-1 IS 408-7995 854176-1 IS 408-9650 1583517-1 IS 408-8812 58636-1 IS 408-7994 58244-3 IS 408-7995
MTA-50 MTA-100 MTA-156 MTA-100
58644-1 IS 408-4406 58245-1 IS 408-7995 58644-2 IS 408-4440 58245-3 IS 408-7995 59844-1 IS 408-7994 58646-1 IS 408-4405 59845-1 IS 408-7994 58646-2 IS 408-4439 59845-3 IS 408-7994 59848-1 IS 408-7995
59848-3 IS 408-7995
Die Set Assembly
Typical Application Rates
Produce 6-in. [15 cm] Long Jumpers, One 4-Position MTA-100 Connector per End, Discrete Wire
Method
Manual Hand Tool 58074-1 with
Interchangeable Head 58246-1
Electric Bench Machine 931800-1 with
Interchangeable Head 58246-1
Electric Bench Machine 931800-1 with
Interchangeable Head and Loose-Piece Feed Track 933567-1
Electric Bench Machine 931800-1 with
Interchangeable Head and Tape Feed Track 853546-1 and 853542-1 (Base)
Terminations
Per Hour
900
1,100
1,250
Apply One 4-Position MTA-100 Feed-Thru Connector per Assembly, Discrete Wire
Method
Manual Bench Tool 58024-1 with
Applicator and Holding Fixture
For further information about tooling call Technical Support.
Terminations
Per Hour
650
Produce 6-in. [15 cm] Long Jumpers, One 4-Position MTA-100 Connector per End, Ribbon Cable*
Method
2700 lb Air Bench Machine 312522-1 with
Applicator and Tape Feed Track 854175-1 and 854200-1 (Base)
* Procedure: Mass terminate 12-conductor ribbon cable with three connectors per end. After terminating, separate by tearing the 12-conductor assembly into three 4-conductor assemblies.
Terminations
Per Hour
7,500
Cable Notching
Method
2700 lb Air Bench Machine 312522-1 with
Ribbon Cable Notcher Assembly 854449-2 and 854468-2 (Adapter)
Cable Ends
Per Hour
1,000
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
79
Application
Tooling
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Part Number Index
Part Number Index
Note: This index lists all cataloged parts
by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated.
Part No. Page
02WEY00007P 72 02WEY00008P 72 02WFY00006P 72 02WFY00007P 72 02WGY00001P 72 02WGY00008P 73 02WJY000001P 73 05WEY00004P 72 05WEY00007P 72 05WFY00006P 72 05WFY00007P 72 05WGY00006P 72 05WGY00008P 73 05WJY000010P 73 10WEY00007P 72 10WEY00012P 72 10WFY00006P 72 10WFY00007P 72 10WGY00002P 72 10WGY00008P 73 10WJY000010P 73 15WEY00002P 72 15WEY00007P 72 15WFY00006P 72 15WFY00007P 72 15WGY00006P 72 15WGY00008P 73 15WJY000010P 73 20WEY00007P 72 20WEY00008P 72 20WFY00006P 72 20WFY00007P 72 20WGY00006P 72 20WGY00008P 73 20WJY000010P 73 24WGY00008P 73 24WJY000010P 73 25WEY00007P 72 25WEY00008P 72 25WFY00006P 72 25WFY00007P 72 25WGY00006P 72 28WEY00007P 72 28WEY00008P 72 28WFY00006P 72 28WFY00007P 72 28WGY00006P 72 57034 71 57040 71 350980 59, 60 640250 60 640251 60 640252 59, 60 640383 46 640384 46 640385 47 640387 49 640388 48
Part No. Page
640389 49 640426 37 640427 37 640428 37 640429 37 640430 37 640431 37 640432 37 640433 37 640434 37 640435 37 640440 15 640441 15 640442 15 640443 15 640445 48 640452 21 640453 21 640454 23 640455 23 640456 24 640457 24 640468 15 640469 15 640470 15 640471 15 640472 37 640473 37 640474 37 640475 37 640476 37 640477 37 640478 37 640479 37 640480 37 640481 37 640550 16 640551 40 640556 41 640557 41 640558 41 640559 41 640595 39 640599 39 640600 39 640601 39 640602 39 640604 39 640605 39 640606 39 640607 39 640608 39 640620 15 640621 15 640622 15 640623 15 640629 42 640630 42 640631 41 640632 41 640633 41 640634 41
Part No. Page
640635 41 640636 17 640637 17 640638 17 640639 17 640642 16 640643 40 640706 59 640707 59 640708 17 640709 17 640859 56 640860 56 640861 56 640862 56 640863 56 640864 56 640865 56 640866 56 640867 56 640868 56 641101 57 641106 57 641113 46 641114 46 641115 47 641118 49 641119 48 641120 48 641121 49 641122 21 641123 21 641124 23 641125 23 641126 24 641127 24 641143 41 641144 41 641145 41 641146 41 641147 41 641148 37 641149 37 641150 37 641151 37 641152 37 641153 37 641154 37 641155 37 641156 37 641157 37 641168 39 641169 39 641170 39 641171 39 641172 39 641173 39 641174 39 641175 39 641176 39 641177 39 641186 17
Part No. Page
641187 17 641188 17 641189 17 641190 15 641191 15 641192 15 641193 15 641198 15 641199 15 641200 15 641201 15 641202 46 641203 46 641204 47 641207 49 641208 48 641209 48 641210 49 641211 21 641212 21 641213 23 641214 23 641215 24 641216 24 641217 37 641218 37 641219 37 641220 37 641221 37 641222 37 641223 37 641224 37 641225 37 641226 37 641227 39 641228 39 641229 39 641230 39 641231 39 641232 39 641233 39 641234 39 641235 39 641236 39 641237 15 641238 15 641239 15 641240 15 641241 15 641242 15 641243 15 641244 15 641283 56 641284 56 641285 56 641286 56 641287 56 641288 56 641289 56 641290 56 641291 56 641292 56
80
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Part Number Index (Continued)
Part No. Page Part No. Page Part No. Page
641293 57 641301 39 641302 39 641303 39 641304 39 641305 39 641306 39 641307 39 641308 39 641309 39 641310 39 641311 15 641312 15 641313 15 641314 15 641425 45 641426 45 641427 45 641428 45 641429 45 641435 45 641436 45 641437 45 641438 45 641439 45 641440 42 641522 45 641523 45 641524 45 641525 45 641526 45 641533 42 641534 15 641535 15 641536 15 641537 15 641550 59 641623 42 641643 17 641644 17 641645 17 641646 17 641653 15 641654 15 641655 15 641656 15 641994 17 643067 40 643071 40 643075 16 643077 16 643498 15 643813 15 643814 15 643815 15 643816 15 643817 37 643818 37 643819 37 643820 37 643821 37 643828 15
643995 45 644020 15 644038 15 644040 15 644042 15 644043 15 644044 15 644082 37 644083 15 644284 37 644312 15 644313 15 644329 55 644370 55 644371 55 644375 55 644376 55 644377 55 644381 55 644382 55 644383 55 644387 55 644388 55 644389 55 644456 22 644457 22 644460 37 644461 37 644462 37 644463 37 644464 37 644465 39 644466 39 644467 39 644468 39 644469 39 644470 39 644471 39 644472 39 644486 30 644487 30 644488 30 644489 30 644497 15 644501 37 644502 37 644508 55 644509 55 644510 55 644511 15 644512 15 644513 15 644514 15 644540 15 644563 15 644564 15 644565 15 644566 37 644567 39 644569 39 644570 39 644572 39
644574 15 644575 15 644576 15 644577 15 644578 15 644579 15 644611 50 644612 50 644613 51 644614 51 644615 50 644616 50 644617 51 644627 50 644628 50 644629 51 644630 51 644631 50 644632 50 644633 51 644662 37 644663 37 644687 37 644694 22 644695 22 644702 15 644718 39 644720 39 644726 15 644749 46 644750 46 644751 47 644752 48 644753 48 644754 49 644755 49 644756 46 644757 46 644758 47 644759 48 644760 48 644761 49 644762 49 644763 46 644764 46 644765 47 644766 48 644767 48 644768 49 644769 49 644783 37 644791 37 644795 15 644803 30 644807 45 644809 45 644812 45 644814 45 644860 37 644861 30 644874 24 644875 24
Part No. Page
644876 23 644877 23 644878 37 644884 22 644885 22 644886 22 644887 22 644888 22 644889 22 644890 22 644891 22 644892 32 644893 32 644894 32 644896 32 644897 32 644898 32 647000 20 647001 20 647002 20 647003 20 647004 20 647005 20 647006 20 647007 20 647008 20 647009 20 647010 20 647011 20 647012 20 647013 20 647014 20 647015 20 647016 20 647017 20 647018 20 647019 20 647020 20 647021 20 647022 20 647023 20 647030 20 647031 20 647032 20 647033 20 647047 27 647048 27 647050 28 647051 28 647075 27 647076 27 647078 28 647079 28 647106 29 647107 29 647108 29 647109 27 647114 27 647116 28 647117 28 647123 53 647124 53
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
Part Number Index
81
MTA, CST-100 II, SL-156 and AMP Economy Power (EP) Connectors
Part Number Index (Continued)
Part No. Page Part No. Page
647125 53 647126 53 647127 53 647128 53 647131 53 647132 53 647133 53 647134 53 647135 53 647136 53 647139 53 647140 53 647141 53 647142 53 647143 53 647144 53 647166 29 647167 29 647168 29 647295 28 647296 28 647297 28 647298 27 647299 27 647300 27 647400 62 647401 62 647402 62 647406 62 647409 62 647466 62 647476 45 647477 15
647478 37 647479 39 647480 15 647481 45 647485 62 647496 39 647497 45 647609 25 647623 25 647624 25 647625 25 647626 25 647627 25 647628 26 647629 26 647630 26 647646 47 647648 52 647649 52 647651 26 647652 26 647653 26 647676 65 647689 65 647690 64 770258 59 770476 59, 60 770522 59 770849 60 770894 61 971111 71 1123721 64 1123722 64
Part No. Page
1123723 65 1123724 68 1123823 69 1123824 69 1318300 65 1318301 68 1318831 69 1318912 64 1375819 31 1375820 31 1445120 9 1445121 10 1445123 9 1445124 10 1445125 9 1445126 10 1445169 9 1445170 9 1445171 9 1445172 10 1445173 10 1445174 10 1445336 31 1445341 7 1445342 7 1445343 7 1445344 7 1445345 7 1445346 7 1445347 7 1445348 7 1445349 7 1445350 7
Part No. Page
1445351 7 1445352 7 1445353 7 1445354 7 1445355 7 1445356 7 1445357 7 1445358 7 1445359 5 1445360 5 1445361 5 1445362 5 1445363 5 1445364 5 1445365 5 1445366 5 1445367 5 1445368 5 1445369 5 1445370 5 1445371 5 1445372 5 1445373 5 1445374 5 1445375 5 1445376 5 1744017 48 1744020 15 1744036 67 1744037 67 1744048 67 1744055 66 1744056 66
Part Number Index
Application Tooling Part Number Index
Part No. Page
58009 76, 79 58010 76, 79 58024 76, 78, 79 58039 76, 79 58040 76, 79 58061 76, 79 58074 76, 77, 79 58075 76, 77 58082 76, 79 58242 76, 79 58243 76, 79 58244 76, 79 58245 76, 79 58246 76, 79 58247 76, 79 58338 76, 77, 79 58392 76, 79 58442 76, 79 58443 76, 79
Part No. Page
58517 31 58575 76, 78, 79 58576 76, 78, 79 58579 76 58614 59 58635 76, 79 58636 76, 79 58638 76, 79 58639 76 58644 76, 79 58646 76, 79 59803 76, 79 59804 76, 79 59836 17 59837 41 59839 76 59845 79 59848 76, 79 90471 59
82
Catalog 82056 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000 Revised 6-08 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 57-1-254-4444 UK: 44-208-420-8341
specified. Values in brackets Specifications subject Mexico: 52-55-1106-0800 Japan: 81-44-844-8013
Part No. Page
91112 78, 79 91579 64 312522 76, 78, 79 354500 79 466468 59 466727 76, 79 466728 76, 79 466747 17 466947 59 471273 78, 79 567020 76, 79 567373 31 567827 31 567828 59 567910 31 680211 59 690675 78, 79 853542 76, 79 853546 76, 79
Part No. Page
853547 76, 79 854175 76, 79 854176 76, 79 854200 76, 79 854449 78 854468 78, 79 856600 76, 79 931800 76, 77, 79 933567 76, 79 933568 76, 79 1385286 64 1583503 76, 79 1583514 76, 79 1583515 76, 79 1583516 76, 79 1583517 76, 79 1583518 76, 79
Americas
Argentina – Buenos Aires
Phone: +54-11-4733-2200 Fax: +54-11-4733-2211
Brasil – São Paulo Phone: +55-11-2103-6000 Fax: +55-11-2103-6030
Chile – Santiago Phone: +56-2-345-0361 Fax: +56-2-223-1477
Asia/Pacific
Australia – Sydney
Phone: +61-2-9554-2600 Fax: +61-2-9502-2556
Product Information Center:
Phone: +61-2-9840-8200 Fax: +61-2-9634-6188
India – Bangalore Phone: +91-80-285-40800 Fax: +91-80-285-40820
Indonesia – Jakarta Phone: +65-6482-0311 Fax: +65-6482-1012
Canada – Toronto Phone: +905-475-6222 Fax: +905-474-5520
Product Information Center:
Phone: +905-470-4425 Fax: +905-474-5525
Colombia – Bogota Phone: +57-1-319-8959 Fax: +57-1-319-8960
Japan – Kawasaki, Kanagawa Phone: +81-44-844-8111 Fax: +81-44-812-3207
Product Information Center:
Phone: +81-44-844-8013 Fax: +81-44-812-3200
Korea – Seoul Phone: +82-2-3415-4500 Fax: +82-2-3486-3810
Malaysia – Selangor Phone: +60-3-7805-3055 Fax: +60-3-7805-3066
Mexico – Mexico City Phone: +52-55-1106-0800
+01-800-733-8926
Fax: +52-55-1106-0901
For Latin/South American Countries not shown
Phone: +54-11-4733-2015 Fax: +54-11-4733-2083
New Zealand – Auckland Phone: +64-9-634-4580 Fax: +64-9-634-4586
Philippines – Makati City Phone: +632-848-0171 Fax: +632-867-8661
People’s Republic of China
Hong Kong Phone: +852-2735-1628 Fax: +852-2735-0243
Shanghai Phone: +86-21-2407-1588 Fax: +86-21-2407-1599
Global Contacts
United States
Harrisburg, PA Phone: +1-717-564-0100 Fax: +1-717-986-7575
Product Information Center:
Phone: +1-800-522-6752 Fax: +1-717-986-7575
Troy, MI Phone: +1-248-273-3359 Fax: +1-248-273-3322
Singapore – Singapore Phone: +65-6482-0311 Fax: +65-6482-1012
Taiwan – Taipei Phone: +886-2-8768-2788 Fax: +886-2-8768-2268
Thailand – Bangkok Phone: +66-2-955-0500 Fax: +66-2-955-0505
Vietnam – Ho Chi Minh City Phone: +84-8-930-5546 Fax: +84-8-930-3443
Europe/Middle East/Africa
Austria – Vienna
Phone: +43-1-905-60-0 Fax: +43-1-905-60-1333
Product Information Center:
Phone: +43-1-905-60-1249 Fax: +43-1-905-60-1251
Belarus – Minsk Phone: +375 17 237 47 94 Fax: +375 17 237 47 94
Belgium – Kessel-Lo Phone: +32-16-352-300 Fax: +32-16-352-355
Bulgaria – Sofia Phone: +359-2-971-2152 Fax: +359-2-971-2153
Czech Republic and Slovakia Czech Republic – Kurim
Phone: +420-541-162-111 Fax: +420-541-162-223
Product Information Center:
Phone: +420-541-162-113 Fax: +420-541-162-132
Denmark – Glostrup Phone: +45-43-48-04-00 Fax: +45-43-44-14-14
Egypt – Cairo Phone: +202-419-2334 Fax: +202-417-7647
Estonia – Tartu Phone: +372-5138-274 Fax: +372-7400-779
Finland – Helsinki Phone: +358-95-12-34-20 Fax: +358-95-12-34-250
France – Cergy-Pontoise Cedex Phone: +33-1-3420-8888 Fax: +33-1-3420-8600
Product Information Center:
Phone: +33-1-3420-8686 Fax: +33-1-3420-8623
France Export Divisions – Cergy-Pontoise Cedex Phone: +33-1-3420-8804 Fax: +33-1-3420-8699
Germany – Bensheim Phone: +49-6251-133-0 Fax: +49-6251-133-1600
Product Information Center:
Phone: +49-6251-133-1999 Fax: +49-6251-133-1988
Greece – Athens Phone: +30-210-9370-396/397 Fax: +30-210-9370-655
Hungary – Budapest Phone: +36-1-289-1000 Fax: +36-1-289-1010
Product Information Center:
Phone: +36-1-289-1016 Fax: +36-1-289-1017
Ireland – Dublin Phone: +353-1-866-5612 Fax: +353-1-866-5714
Israel – Petach-Tikva Phone: +972-3-929-0999 Fax: +972-3-919-1088
Italy – Collegno (Torino) Phone: +39-011-4012-111 Fax: +39-011-4031-116
Product Information Center:
Phone: +39-011-4012-428 Fax: +39-011-40-287-428
Lithuania and Latvia Lithuania – Vilnius
Phone: +370-5-213-1402 Fax: +370-5-213-1403
Product Information Center:
Phone: +370-5-211-3016 Fax: +370-5-213-1403
Netherlands – ’s-Hertogenbosch Phone: +31-73-6246-246 Fax: +31-73-6212-365
Product Information Center:
Phone: +31-73-6246-999 Fax: +31-73-6246-998
Norway – Nesbru Phone: +47-66-77-88-50 Fax: +47-66-77-88-55
Poland – Warsaw Phone: +48-22-4576-700 Fax: +48-22-4576-720
Product Information Center:
Phone: +48-22-4576-704 Fax: +48-22-4576-720
Romania – Bucharest Phone: +40-21-311-3479/3596 Fax: +40-21-312-0574
Russia – Moscow Phone: +7-495-790-7902 Fax: +7-495-721-1893
Product Information Center:
Phone: +7-495-790-7902-404 Fax: +7-495-790-7902-401
Russia – St. Petersburg Phone: +7-812-718-8192 Fax: +7-812-718-8193
Slovenia – Ljubljana Phone: +386-1561-3270 Fax: +386-1561-3240
South Africa – Port Elizabeth Phone: +27-41-503-4500 Fax: +27-41-581-0440
Spain – Barcelona Phone: +34-93-291-0330 Fax: +34-93-201-7879
Sweden – Upplands Väsby Phone: +46-8-50-72-50-00 Fax: +46-8-50-72-50-01
Switzerland – Steinach Phone: +41-71-447-0447 Fax: +41-71-447-0444
Turkey – Istanbul Phone: +90-212-281-8181/2/3
+90-212-282-5130/5430
Fax: +90-212-281-8184
Ukraine – Kiev Phone: +380-44-206-2265 Fax: +380-44-206-2264
Product Information Center:
Phone: +380-44-206-2265 Fax: +380-44-206-2264
United Kingdom – Stanmore, Middlesex Phone: +44-8706-080208 Fax: +44-208-954-6234
Product Information Center:
Freephone (UK only):
+0800-267-666
Phone: +44-8706-080208 Fax: +44-208-420-8095
Tyco Electronics Corporation www.tycoelectronics.com
Tyco Electronics Corporation
Harrisburg, PA
82056–10K–MS–FP–6-08–OG3B
Loading...