Product Facts
■ 10+ Gbps performance
00 ohm Impedance for
■ 1
Differential Pair
configuration
■ 5 pair version offers 26
pairs/10mm [66 differential
airs/inch] fitting within a
p
25.40 [1.00] card slot pitch
■ 4 pair version offers 21
pairs/10mm [53 differential
pairs/inch] fitting within a
20.30 [.800] card slot pitch
■ 3 pair version offering 16
pairs/10mm [40 differential
pairs/inch] fitting within a
16.25 [.625] card slot pitch
■ Right angle pin headers
(coplanar) in 3 pair, 4 pair,
and 5 pair versions
■ Reliable, redundant contact
design on every signal
contact
■ Modular system offered in
various column versions
■ Meets Industry reliability
requirements of Bellcore/
Telcordia
■ Sequencing for ground and
signal contacts
■ RoHS Compliant
Future Product Extensions
■ Vertical receptacles
■ High speed cable
assemblies and hardware
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Introduction
The Z-PACK TinMan
backplane connector
family is a cost-effective
solution for customers
searching for a high density,
high performance backplane interconnect system.
The Z-PACK TinMan
connector design follows
proven industry backplane
convention by offering a fully
protected right-angle receptacle for use on daughtercards where handling
damage can be a concern
when mating to a vertical
male header. This connector permits field repairability
at either the module or
single pin levels.
Ground contacts positioned
within each column of the
connector, combined with
unique contact lead frame
arrangements, enable the
Z-PACK TinMan connector
to achieve low crosstalk and
high through-put performance levels. Reliability is
provided with a dual point
of contact mating interface
and compliant pin interface
to the printed circuit board.
Industry Applications
Ideally designed for cost
pressured, high signal density applications requiring
interconnection between two
printed circuit boards, such
as those typically found in
server, storage, switch,
router, and similar applications. The Z-PACK TinMan
connector product family is
suited to meet the demands
of today’s modular system
designs by offering a
variety of configurations.
The product family includes
configurations to fit 20.32
[.800] and 25.40 [1.00] card
slot spacing.
Technical Documents
Product Specification 108-2303
Application Specification
114-13202
Routing Guide Report #27GC001-1
Material and Finish
Signal Contact — High Strength
Copper Alloy
Ground Contact — High Strength
Copper Alloy
Housing — Liquid Crystal Polymer
Platings — Telcordia compliant inter-
face, Nickel underplate
Compliant Pin Plating —
RoHS Compliant
Ratings
Temperature Range —
-65°C to +90°C
Current Rating — 0.5 A/contact @
< 30°C T-Rise
Durability — 200 cycles
Dielectric Withstanding Voltage —
560 VAC
Operating Voltage — 250 VAC max.
Signal Integrity
Characteristic Impedance —
Differential @ 100 ohms ±10%
Crosstalk — Multi-pair differential
crosstalk: 2.1% @ 50ps
Insertion Loss — -2 dB @ 10 GHz
For additional information visit:
http://www.tycoelectronics.com/zpacktinman
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
1
-PACK TinMan High Speed,
RoHS
Customer
Support
Center
Z
High Density Backplane Connector
Introduction (Continued)
Need more information?
C
numbers listed below.
Technical Support is staffed
with specialists well versed
in Tyco Electronics products.
They can provide you with:
■ Technical support
■ Catalogs
■ T
■ Product Samples
■ Authorized Distributor
Disclaimer
While Tyco Electronics Corporation
and its affiliates referenced herein
“Tyco Electronics”) have made every
(
easonable effort to ensure the accuracy
r
o
Tyco Electronics does not guarantee that
it is error-free, nor does Tyco Electronics
make any other representation, warranty
or guarantee that the information is
accurate, correct, reliable or current.
Tyco Electronics reserves the right to
make any adjustments to the information
contained herein at any time without
notice. Tyco Electronics expressly disclaims all implied warranties regarding the
information contained herein, including,
but not limited to, any implied warranties
of merchantability or fitness for a particular purpose. Tyco Electronics’ only obligations are those in the Tyco Electronics
Standard Terms and Conditions of Sale,
and in no case will Tyco Electronics be
responsible for any incidental, indirect, or
consequential damages arising from the
sale, resale, use, or misuse of its products.
Users should independently evaluate the
suitability of, and test each product for,
their application.
The dimensions, specifications, designs,
construction, materials and processes in
this catalog are for reference purposes
only and are subject to change without
notice. Please consult Tyco Electronics
for the most current product information.
The export of certain Tyco Electronics
products is restricted by the Arms Export
Control Act (Title 22, U.S.C.
Sec 2751, et seq.) or the Export
Administration Act of 1979, as amended
(Title 50, U.S.C., App. 2401 et seq.).
Orders may be subject to export approval
by the U.S. Government. Buyer must
comply with all applicable export laws of
all applicable jurisdictions.
© 2005 and 2007 by Tyco Electronics
Corporation.
All International Rights Reserved.
AMP, MULTI-BEAM XL, MULTIGIG RT,
Z-PACK, Z-PACK TinMan and TE LOGO
and Tyco Electronics are trademarks.
Other products, logos, and company
names mentioned herein may be
trademarks of their respective owners.
2
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
all Technical Support at the
echnical Documents
Locations
f the information in this catalog,
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Restriction on the use of Hazardous Substances
(RoHS)
At Tyco Electronics, we’re ready to support your RoHS requirements. We’ve assessed more than 1.5 million end items/components for RoHS compliance, and issued new part numbers
where any change was required to eliminate the restricted materials. Part numbers in this catalog are identified as:
RoHS Compliant — Part numbers in this catalog are RoHS
Compliant, unless marked otherwise. These products comply
with European Union Directive 2002/95/EC as amended 1
January 2006 that restricts the use of lead, mercury, cadmium,
hexavalent chromium, PBB, and PBDE in certain electrical and
electronic products sold into the EU as of 1 July 2006.
NOTE: For purposes of this Catalog, included within the definition of RoHS Compliant are products that are clearly “Out of
Scope” of the RoHS Directive such as hand tools and other
non-electrical accessories.
NOTE: Information regarding RoHS compliance is provided
based on reasonable inquiry of our suppliers and represents our
current actual knowledge based on the information provided by
our suppliers. This information is subject to change. For latest
compliance status, refer to our website referenced at right.
Getting the Information You Need
Our comprehensive on-line RoHS Customer Support Center
provides a forum to answer your questions and support your
RoHS needs. A RoHS FAQ (Frequently Asked Questions) is
available with links to more detailed information. You can also
submit RoHS questions and receive a response within 24 hours
during a normal work week. The Support Center also provides:
■ Cross-Reference from
Non-compliant to Compliant Products
■ Ability to browse RoHS
Compliant Products in our
on-line catalog
■ Downloadable Technical Data
Customer Information
Presentation
■ More detailed information
regarding the definitions
used above
■ So whatever your questions when it comes to RoHS, we’ve
got the answers at www.tycoelectronics.com/leadfree
Table of Contents
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Introduction (Continued)
ntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
I
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5 Pair Right Angle Receptacle Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Pair Right Angle Receptacle Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Pair Right Angle Receptacle Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Pair Vertical Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5 Pair Vertical Header Assemblies — Left End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5 Pair Vertical Header Assemblies — Right End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5 Pair Vertical Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Pair Vertical Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Pair Vertical Header Assemblies — Left End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 Pair Vertical Header Assemblies — Right End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4 Pair Vertical Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3 Pair Vertical Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3 Pair Vertical Header Assemblies — Left End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3 Pair Vertical Header Assemblies — Right End Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3 Pair Vertical Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5 Pair Right Angle Pin Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5 Pair Right Angle Pin Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . 22
4 Pair Right Angle Pin Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4 Pair Right Angle Pin Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . 24
3 Pair Right Angle Pin Header Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3 Pair Right Angle Pin Header Assemblies — Double End Walls . . . . . . . . . . . . . . . . . . . . 26
Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview . . . . . . . . . . . . . . . . . . . 27-29
6 Pair Mid-Plane Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-32
4 Pair Mid-Plane Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-35
Z-PACK TinMan Product Mating Sequence Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Z-PACK MAX Part Number to Z-PACK TinMan Part Number Cross-Reference . . . . . . 37, 38
Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
3
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Introduction (Continued)
Noise Table
■ Maximum, multiple source
crosstalk
otal Peak Receiver Noise
Victim Pair
AB9 0.8%
BC8 1.6%
E9 1.9%
D
F8 1.9%
E
GH9 2.0%
I8 2.0%
H
G9 2.0%
J
KL8 2.1%
MN9 1.7%
O8 0.8%
N
Note: Data includes PCB vias of both backplane and
aughtercard connectors. Single mated connector
d
pair 50 ps (20-80%) edge rate
T
or Recommended Pin-Out
f
Insertion Loss Plot
4
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Representative Eye Pattern
■ 10.0 Gbps data rate
7
1 PRBS
■ 2
-
■ Unequalized Signal
Customer Connector
Evaluation Kit
■ Connector characterization
■ Available for loan — contact
your local Tyco Electronics
Sales Engineer
■ Time and frequency domain
testable
■ Testable to 18+ GHz (25+ Gb/s)
■ Multiple calibration options
■ Convenient SMA interface
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Introduction (Continued)
Customer System
Evaluation Kit
■ System characterization
■ Available for loan — contact
your local Tyco Electronics
Sales Engineer
■ Time and frequency domain
testable
■ Testable to 18+ GHz (25+ Gb/s)
■ Multiple system lengths
■ Convenient SMA interface
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
5
-PACK TinMan High Speed,
A
3
1.81
± 0.05
[
1.252
± .002
]
2
2.30
± 0.08
[.878
± .003
]
1
9.50
[
.768]
19.60
[.772]
24.40
± 0.10
[.961
± .004
]
1.90
[.075]
Ref.
2.20
[
.087]
Ref.
F
inished Hole Size and
Plated Thru Holes*
Connector Outline
9.30
[.366]
Ref.
11.00
[.433]
Recommended PC Board Layout
Daughterboard
Component Side Shown
Ref.
19.60
[.772]
Ref.
B
0.80
[.031]
Ref.
1.25
[.049]
Ref.
1.90
[.075]
Typ.
1 8
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.21
[.048]
Ref.
1
.40
[.055]
Ref.
1.70
[.067]
Ref.
1.40
[.055]
R
ef.
Row A
Row A
Row O
Row N
Row M
Row L
Row K
Row J
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
Z
High Density Backplane Connector
5 Pair Right Angle Receptacle Assemblies
imension
olumn Part Number
C
8 1934218-1
6 1934221-1
1
D
AB
15.35 13.30
.604 .524 1934271-1, 1934349-1, 1934350-1
0.55 28.50
3
.203 1.122 1934332-1, 1934347-1, 1934348-1
1
* Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202.
pplication
A
ooling
T
*
*
ates With
M
1934269-1,(R) 1934272-1,(L) 1934273-1,
934331-1, 1934334-1, 1934333-1,
1
6
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
0.013
0.02
0.004
0.05
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
[.018 ±
.001
.0005
.002
.0002
]
]
]
]
-PACK TinMan High Speed,
Row A
A
2
7.61
±
0.05
[1.087
± .002
]
15.30
[.602]
15.40
[.606]
20.20
± 0.10
[.795
±
.004
]
1
.90
[.075]
Ref.
2.20
[.087]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
11.00
[.433]
Recommended PC Board Layout
Daughterboard
Component Side Shown
Ref.
15.40
[
.606]
R
ef.
B
0.80
[.031]
Ref.
1.25
[.049]
Ref.
1.90
[.075]
Typ.
1 8
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.21
[.048]
Ref.
1
.40
[.055]
Ref.
1.70
[.067]
Ref.
1.40
[
.055]
R
ef.
Row A
Row L
Row K
Row J
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
9.30
[.366]
Ref.
Ref.
18.10
± 0.08
[
.713
± .003
]
Z
High Density Backplane Connector
4 Pair Right Angle Receptacle Assemblies
imension
olumn Part Number
C
8 1934222-1
6 1934225-1
1
D
AB
15.35 13.30
.604 .524 1934306-1, 1934225-1, 1934354-1,
0.55 28.50
3
.203 1.122 1934316-1, 1934351-1, 1934352-1,
1
* Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202.
pplication
A
ooling
T
*
*
ates With
M
1934226-1, 1934304-1, 1934303-1,
934315-1, 1934318-1, 1934317-1,
1
0.05
0.013
0.02
0.004
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
.001
.0005
.002
.0002
]
]
]
]
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
7
-PACK TinMan High Speed,
Row A
A
2
3.41
± 0.05
[.922
±
.002
]
1
1.10
[.437]
11.20
[.441]
16.00
± 0.10
[
.630
± .004
]
1
.90
[.075]
Ref.
2.20
[.087]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
11.00
[.433]
Recommended PC Board Layout
Daughterboard
Component Side Shown
Ref.
1
1.20
[.441]
Ref.
B
0.80
[.031]
Ref.
1.25
[.049]
Ref.
1.90
[.075]
Typ.
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.21
[.048]
Ref.
1
.40
[.055]
Ref.
1.70
[
.067]
R
ef.
1.40
[
.055]
R
ef.
Row A
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
9.30
[.366]
Ref.
R
ef.
13.90
± 0.08
[
.547
± .003
]
Z
High Density Backplane Connector
3 Pair Right Angle Receptacle Assemblies
imension
olumn Part Number
C
8 1934226-1
0 1934228-1
1
6 1934229-1
1
Custom tooling not required. Utilizes flat-rock insertion tooling. Reference Application Specification 114-13202.
*
D
AB
15.35 13.30
.604 .524 1934302-1, 1934359-1, 1934360-1,
9.15 17.10
1
754 .673 1934342-1, 1934357-1, 1934358-1,
.
0.55 28.50
3
.203 1.122 1934346-1, 1934355-1, 1934356-1,
1
pplication
A
ooling
T
*
*
*
ates With
M
1934299-1, 1934300-1, 1934301-1,
934339-1, 1934341-1, 1934340-1,
1
934339-1, 1934340-1, 1934345-1,
1
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
0.013
0.02
0.004
0.05
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
8
Report #27GC001-1.
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
A
2.80
± 0.05
[.110
± .002
]
6.00
± 0.15
[
.236
±
.006
]
4.50
± 0.15
[.177
± .006
]
1
1.80
± 0.10
[.465
±
.004
]
22.60
±
0.08
[
.890
± .003
]
2.40
[
.094]
19.60
[.772]
24.40
±
0.10
[.961
± .004
]
1.90
[.075]
Ref.
2.38
[
.094]
R
ef.
1.40
[
.055]
R
ef.
R
ef.
2.50
[
.098]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
1.425
[.056]
Ref.
.625
[.025]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1.40
[.055]
Ref.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
Row M
Row N
Row O
-X-
-Y-
BSC
BSC
1.425
[.056]
Ref.
R
ow A
-PACK TinMan High Speed,
Z
High Density Backplane Connector
5 Pair Vertical Header Assemblies
olumn Part Number
C
8 1934269-1
6 1934331-1
1
* Reference Application Specification 114-13202.
imension
D
AB
15.35 13.30
.604 .524
0.55 28.50
3
.203 1.122
1
pplication
A
T
ooling*
ates With
M
1-1804791-1 1934218-1
-1804791-2 1934221-1
1
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Report #27GC001-1.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
9
A
2.80
±
0.05
[.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
4.50
± 0.15
[.177
±
.006
]
1
1.50
± 0.10
[.453
± .004
]
22.60
± 0.08
[
.890
± .003
]
2
.40
[.094]
19.60
[.772]
24.40
± 0.10
[.961
± .004
]
1.90
[.075]
Ref.
2.38
[.094]
Ref.
1
.40
[.055]
Ref.
Ref.
2.50
[
.098]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
2.38
[.094]
Ref.
0.63
[.025]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1.40
[
.055]
R
ef.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
Row M
Row N
Row O
-X-
-Y-
BSC
BSC
Row A
-PACK TinMan High Speed,
Z
High Density Backplane Connector
5 Pair Vertical Header Assemblies — Left End Wall
imension
olumn Part Number
C
8 1934272-1
6 1934333-1
1
D
AB
16.30 13.30
.642 .524
1.50 28.50
3
.240 1.122
1
* Reference Application Specification 114-13202.
pplication
A
ooling*
T
1-1804791-1 1934218-1
-1804791-2 1934221-1
1
ates With
M
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
10
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
0.05
0.013
0.02
0.004
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
.001
.0005
.002
.0002
]
]
]
]
A
2.80
±
0.05
[.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
4.50
± 0.15
[.177
±
.006
]
1
1.80
± 0.10
[.465
± .004
]
22.60
± 0.08
[
.890
± .003
]
2
.40
[.094]
19.60
[.772]
24.40
± 0.10
[.961
± .004
]
1.90
[.075]
Ref.
2.38
[
.094]
R
ef.
1.40
[
.055]
R
ef.
Ref.
2.50
[
.098]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
1.425
[.056]
Ref.
2.27
[.089]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1
.40
[.055]
Ref.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
Row M
Row N
Row O
-X-
-Y-
BSC
BSC
R
ow A
-PACK TinMan High Speed,
Z
High Density Backplane Connector
5 Pair Vertical Header Assemblies — Right End Wall
imension
olumn Part Number
C
8 1934273-1
6 1934334-1
1
D
AB
17.00 13.30
.669 .524
2.20 28.50
3
.268 1.122
1
* Reference Application Specification 114-13202.
pplication
A
T
ooling*
ates With
M
1-1804791-1 1934218-1
-1804791-2 1934221-1
1
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
0.05
0.013
0.02
0.004
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
.001
.0005
.002
.0002
]
]
]
]
11
-PACK TinMan High Speed,
A
2.80
±
0.05
[.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
4.50
± 0.15
[.177
±
.006
]
1
1.80
± 0.10
[.465
± .004
]
22.60
± 0.08
[
.890
± .003
]
2.40
[
.094]
19.60
[.772]
24.40
± 0.10
[.961
± .004
]
1.90
[
.075]
R
ef.
2.38
[
.094]
R
ef.
1.40
[
.055]
R
ef.
R
ef.
2.50
[
.098]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
2.375
[.093]
Ref.
2.275
[.089]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1.40
[.055]
Ref.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
Row M
Row N
Row O
-X-
-Y-
BSC
BSC
R
ow A
Z
High Density Backplane Connector
5 Pair Vertical Header Assemblies — Double End Walls
imension
olumn Part Number
C
8 1934271-1
6 1934332-1
1
D
AB
17.95 13.30
.707 .524
3.15 28.50
3
.305 1.122
1
* Reference Application Specification 114-13202.
pplication
A
T
ooling*
ates With
M
1-1804791-1 1934218-1
-1804791-2 1934221-1
1
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
12
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
]
.0002
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
]
]
]
-PACK TinMan High Speed,
A
2.80
± 0.05
[
.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
4.50
±
0.15
[.177
± .006
]
11.80
±
0.10
[
.465
± .004
]
2
.40
[.094]
15.40
[.606]
1.90
[.075]
Ref.
1.40
[.055]
Ref.
Ref.
2.50
[
.098]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
1.425
[.056]
Ref.
.625
[.025]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1.40
[.055]
Ref.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
-X-
-Y-
BSC
BSC
1.425
[
.056]
R
ef.
+
0.08
–
0.20
+
.003
–
.008
1
8.40
[.724
]
+ 0.10
– 0.55
+ .004
– .022
20.20
[
.795
]
Row A
Z
High Density Backplane Connector
4 Pair Vertical Header Assemblies
imension
olumn Part Number
C
8 1934305-1
6 1934315-1
1
D
AB
15.35 13.30
.604 .524
0.55 28.50
3
.202 1.122
1
* Reference Application Specification 114-13202.
pplication
A
T
ooling*
ates With
M
1-1804790-1 1934222-1
-1804790-3 1934225-1
1
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Report #27GC001-1.
13
A
2.80
± 0.05
[
.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
4.50
±
0.15
[.177
± .006
]
11.80
±
0.10
[.465
± .004
]
2
.40
[.094]
15.40
[.606]
1.90
[.075]
Ref.
1.40
[.055]
Ref.
Ref.
2.50
[
.098]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
2.375
[.094]
Ref.
.625
[.025]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1.40
[.055]
Ref.
-X-
-Y-
BSC
BSC
2.375
[
.094]
R
ef.
+
0.08
–
0.20
+
.003
–
.008
1
8.40
[.724
]
+ 0.10
– 0.55
+ .004
– .022
20.20
[
.795
]
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
Row A
-PACK TinMan High Speed,
Z
High Density Backplane Connector
4 Pair Vertical Header Assemblies — Left End Wall
imension
olumn Part Number
C
8 1934303-1
6 1934317-1
1
D
AB
17.00 13.30
.669 .524
1.50 28.50
3
.240 1.122
1
* Reference Application Specification 114-13202.
pplication
A
T
ooling*
ates With
M
1-1804790-1 1934222-1
-1804790-3 1934225-1
1
0.05
0.013
0.02
0.004
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
.001
.0005
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
14
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
.002
.0002
]
]
]
]
A
2.80
± 0.05
[
.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
4.50
±
0.15
[.177
± .006
]
11.80
±
0.10
[
.465
± .004
]
2
.40
[.094]
15.40
[.606]
1.90
[.075]
Ref.
1.40
[.055]
Ref.
Ref.
2.50
[
.098]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
1.425
[.056]
Ref.
2.275
[.090]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1
.40
[.055]
Ref.
-X-
-Y-
BSC
BSC
1.425
[
.056]
R
ef.
+
0.08
–
0.20
+
.003
–
.008
1
8.40
[.724
]
+ 0.10
– 0.55
+ .004
– .022
20.20
[
.795
]
Row A
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
-PACK TinMan High Speed,
Z
High Density Backplane Connector
4 Pair Vertical Header Assemblies — Right End Wall
imension
olumn Part Number
C
8 1934304-1
6 1934318-1
1
D
AB
16.30 13.30
.642 .524
2.20 28.50
3
.268 1.122
1
* Reference Application Specification 114-13202.
pplication
A
T
ooling*
ates With
M
1-1804790-1 1934222-1
-1804790-3 1934225-1
1
0.05
0.013
0.02
0.004
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
.001
.0005
.002
.0002
]
]
]
]
15
-PACK TinMan High Speed,
A
2.80
± 0.05
[
.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
4.50
±
0.15
[.177
± .006
]
11.80
±
0.10
[
.465
± .004
]
2
.40
[.094]
15.40
[.606]
1
.90
[.075]
Ref.
1.40
[.055]
Ref.
Ref.
2.50
[
.098]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Backplane
Component Side Shown
B
2.375
[.094]
Ref.
2.275
[.090]
Ref.
1.90
[.075]
Typ.
Ref.
1.40
[.055]
Typ.
2.40
[.094]
Ref.
2.40
[.094]
Ref.
1.40
[
.055]
R
ef.
-X-
-Y-
BSC
BSC
2.375
[
.094]
R
ef.
+
0.08
–
0.20
+
.003
–
.008
1
8.40
[.724
]
+ 0.10
– 0.55
+ .004
– .022
20.20
[
.795
]
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
Row J
Row K
Row L
Row A
Z
High Density Backplane Connector
4 Pair Vertical Header Assemblies — Double End Walls
imension
olumn Part Number
C
8 1934306-1
6 1934316-1
1
D
AB
17.95 13.30
.707 .524
3.15 28.50
3
.305 1.122
1
* Reference Application Specification 114-13202.
pplication
A
T
ooling*
ates With
M
1-1804790-1 1934222-1
-1804790-3 1934225-1
1
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
]
.0002
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
16
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
]
]
]
-PACK TinMan High Speed,
A
1.90
[.075]
Ref.
2.50
[
.098]
R
ef.
2
.40
[.094]
Ref.
1.40
[.055]
Typ.
Ref.
1
.425
[.056]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
11.80
± 0.10
[
.465
± .004
]
4
.50
± 0.15
[.177
± .006
]
2
.80
± 0.05
[.110
± .002
]
6.00
± 0.15
[.236
±
.006
]
Recommended PC Board Layout
Component Side Shown
2.40
[.094]
Ref.
2.40
[.094]
Ref.
11.20
[.441]
Ref.
1.40
[.055]
Typ.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
-X-
BSC
B
1.425
[.056]
Ref.
0.625
[.025]
Ref.
1.90
[.075]
Typ.
BSC
-Y-
+ 0.10
– 0.55
+ .004
– .022
16.00
[
.630
]
+ 0.08
– 0.20
+ .003
– .008
14.20
[
.559
]
1
.40
[
.055]
Ref.
R
ow A
Z
High Density Backplane Connector
3 Pair Vertical Header Assemblies
imension
olumn Part Number
C
8 1934299-1
0 1934339-1
1
6 1934343-1
1
Reference Application Specification 114-13202.
*
D
AB
15.53 13.30
.611 .524
9.15 17.10
1
754 .673
.
0.55 28.50
3
.203 1.122
1
pplication
A
T
ooling*
ates With
M
1-1901457-1 1934226-1
-1901457-2 1934228-1
1
-1901457-3 1934229-1
1
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.02
0.004
0.05
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
17
-PACK TinMan High Speed,
A
1
.90
[.075]
Ref.
2.50
[.098]
Ref.
2.40
[
.094]
R
ef.
1
.40
[.055]
T
yp.
Ref.
2.375
[
.094]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
1
1.80
± 0.10
[.465
± .004
]
4.50
±
0.15
[.177
± .006
]
2.80
±
0.05
[.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
Recommended PC Board Layout
Component Side Shown
2.40
[.094]
Ref.
2.40
[.094]
Ref.
11.20
[.441]
Ref.
1.40
[.055]
Typ.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
-X-
BSC
B
2.375
[.094]
Ref.
0.625
[.025]
Ref.
1.90
[.075]
Typ.
BSC
-Y-
+ 0.10
– 0.55
+ .004
– .022
16.00
[.630
]
+ 0.08
– 0.20
+ .003
– .008
14.20
[.559
]
1.40
[
.055]
R
ef.
R
ow A
Z
High Density Backplane Connector
3 Pair Vertical Header Assemblies — Left End Wall
imension
olumn Part Number
C
8 1934300-1
10
6 1934344-1
1
Reference Application Specification 114-13202.
*
934340-1
1
D
AB
16.30 13.30
.642 .524
0.10 17.10
2
791 .673
.
1.50 28.50
3
.240 1.122
1
pplication
A
ooling*
T
1-1901457-1 1934226-1
-1901457-2 1934228-1
1
-1901457-3 1934229-1
1
ates With
M
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
18
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
-PACK TinMan High Speed,
A
1.90
[.075]
Ref.
2.50
[.098]
Ref.
2.40
[
.094]
R
ef.
1
.40
[.055]
T
yp.
Ref.
1.425
[
.056]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
1
1.80
± 0.10
[.465
± .004
]
4.50
±
0.15
[.177
± .006
]
2.80
±
0.05
[.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
Recommended PC Board Layout
Component Side Shown
2.40
[.094]
Ref.
2.40
[.094]
Ref.
11.20
[.441]
Ref.
1.40
[.055]
Typ.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
-X-
BSC
B
1.425
[.056]
Ref.
2.275
[.090]
Ref.
1.90
[.075]
Typ.
BSC
-Y-
+ 0.10
– 0.55
+ .004
– .022
16.00
[.630
]
+ 0.08
– 0.20
+ .003
– .008
14.20
[.559
]
1
.40
[.055]
Ref.
Row A
Z
High Density Backplane Connector
3 Pair Vertical Header Assemblies — Right End Wall
imension
olumn Part Number
C
8 1934301-1
10
6 1934345-1
1
Reference Application Specification 114-13202.
*
934341-1
1
D
AB
17.00 13.30
.669 .524
0.08 17.10
2
791 .673
.
2.20 28.50
3
.268 1.122
1
pplication
A
ooling*
T
1-1901457-1 1934226-1
-1901457-2 1934228-1
1
-1901457-3 1934229-1
1
ates With
M
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
19
-PACK TinMan High Speed,
A
1
.90
[.075]
Ref.
2.50
[.098]
Ref.
2
.40
[.094]
Ref.
1
.40
[.055]
T
yp.
Ref.
2.375
[
.094]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
1
1.80
± 0.10
[.465
± .004
]
4.50
± 0.15
[.177
± .006
]
2.80
± 0.05
[.110
± .002
]
6.00
± 0.15
[
.236
± .006
]
Recommended PC Board Layout
Component Side Shown
2.40
[.094]
Ref.
2.40
[.094]
Ref.
11.20
[.441]
Ref.
1.40
[.055]
Typ.
Row A
Row B
Row C
Row D
Row E
Row F
Row G
Row H
Row I
-X-
BSC
B
2.375
[.094]
Ref.
2.275
[.090]
Ref.
1.90
[.075]
Typ.
BSC
-Y-
+ 0.10
– 0.55
+ .004
– .022
16.00
[.630
]
+ 0.08
– 0.20
+ .003
– .008
14.20
[.559
]
1.40
[.055]
Ref.
Row A
Z
High Density Backplane Connector
3 Pair Vertical Header Assemblies — Double End Walls
imension
olumn Part Number
C
8 1934302-1
10
6 1934346-1
1
Reference Application Specification 114-13202.
*
934342-1
1
D
AB
17.95 13.30
.707 .524
1.75 17.10
2
856 .673
.
3.15 28.50
3
.305 1.122
1
pplication
A
T
ooling*
ates With
M
1-1901457-1 1934226-1
-1901457-2 1934228-1
1
-1901457-3 1934229-1
1
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
20
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
-PACK TinMan High Speed,
A
19.60
[.772]
1
.90
[.075]
Ref.
0
.625
[.025]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Component Side Shown
B
0.90
[.035]
Ref.
0.90
[.035]
Ref.
1.95
[.077]
Ref.
1.15
[.045]
Ref.
1.90
[.075]
Typ.
18
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.21
[.048]
Ref.
1.40
[
.055]
R
ef.
Row A
Row O
Row N
Row M
Row L
Row K
Row J
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
15.80
[.622]
Ref.
27.61
±
0.05
[1.087
± .002
]
2
.20
±
0.15
[.087
± .006
]
1
9.50
[.768]
R
ef.
9.00
± 0.13
[
.354
± .005
]
6
.80
[.268]
Ref.
6
.00
[.236]
Ref.
4.50
[.177]
Ref.
19.60
[
.772]
R
ef.
1.40
[.055]
Ref.
1.70
[
.067]
R
ef.
Row A
+ 0.10
– 0.55
+ .004
– .022
24.40
[
.961
]
+ 0.08
– 0.20
+ .003
– .008
22.60
[.890
]
Z
High Density Backplane Connector
5 Pair Right Angle Pin Header Assemblies
imension
olumn Part Number
C
8 1934349-1
6 1934347-1
1
* Custom tooling not required. Utilizes flat-rock insertion tooling.
eference Application Specification 114-13202.
R
D
AB
15.35 13.30
.604 .524
0.55 28.50
3
.203 1.122
1
A
pplication
ooling
T
M
* 1934218-1
*
1934221-1
ates With
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
0.013
0.02
0.004
0.05
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
[.018 ±
.001
.0005
.002
.0002
]
]
]
]
21
-PACK TinMan High Speed,
A
2
7.61
± 0.05
[1.087
± .002
]
19.60
[.772]
1.90
[
.075]
R
ef.
2.375
[
.094]
R
ef.
2.20
± 0.15
[.087
± .006
]
19.50
[.768]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
9.00
± 0.13
[
.354
± .005
]
Recommended PC Board Layout
Component Side Shown
6.80
[
.268]
R
ef.
6.00
[.236]
Ref.
4.50
[
.177]
R
ef.
1
9.60
[.772]
Ref.
B
0.90
[.035]
Ref.
2.65
[.104]
Ref.
0.90
[.035]
Ref.
1.95
[.077]
Ref.
2.10
[.083]
Ref.
1.90
[.075]
Typ.
18
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.21
[.048]
Ref.
1.40
[
.055]
R
ef.
1.70
[
.067]
R
ef.
1.40
[.055]
Ref.
R
ow A
Row A
Row O
Row N
Row M
Row L
Row K
Row J
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
15.80
[.622]
Ref.
+
–
+
–
2
4.40
[.961
]
+ 0.08
– 0.20
+ .003
– .008
22.60
[.890
]
Z
High Density Backplane Connector
5 Pair Right Angle Pin Header Assemblies — Double End Walls
imension
olumn Part Number
C
8 1934350-1
6 1934348-1
1
* Custom tooling not required. Utilizes flat-rock insertion tooling.
eference Application Specification 114-13202.
R
D
AB
18.05 13.30
.711 .524
3.25 28.50
3
.309 1.122
1
pplication
A
ooling
T
* 1934218-1
*
ates With
M
1934221-1
22
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.02
0.004
0.05
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
.001
.0005
.002
.0002
]
]
]
]
-PACK TinMan High Speed,
A
15.40
[.606]
1.90
[
.075]
R
ef.
0.625
[
.025]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Component Side Shown
B
0.90
[.035]
Ref.
0.90
[.035]
Ref.
1.95
[.077]
Ref.
1.15
[.045]
Ref.
1.90
[.075]
Typ.
18
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.80
[.071]
Ref.
1.40
[
.055]
R
ef.
Row A
Row L
Row K
Row J
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
15.80
[.622]
Ref.
2
4.00
± 0.05
[.945
± .002
]
2.20
± 0.15
[
.087
± .006
]
1
5.30
[.602]
R
ef.
9
.00
± 0.13
[.354
±
.005
]
6
.80
[.268]
Ref.
6.00
[
.236]
R
ef.
4
.50
[.177]
Ref.
1
5.40
[.606]
Ref.
1.40
[
.055]
R
ef.
1
.70
[.067]
Ref.
Row A
+ 0.10
– 0.55
+ .004
– .022
20.20
[
.795
]
+ 0.08
– 0.20
+ .003
– .008
18.40
[.724
]
Z
High Density Backplane Connector
4 Pair Right Angle Pin Header Assemblies
imension
olumn Part Number
C
8 1934353-1
6 1934351-1
1
* Custom tooling not required. Utilizes flat-rock insertion tooling.
eference Application Specification 114-13202.
R
D
AB
15.35 13.30
.604 .524
0.55 28.50
3
.203 1.122
1
A
pplication
ooling
T
M
* 1934222-1
*
1934225-1
ates With
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
0.013
0.02
0.004
0.05
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
[.018 ±
.001
.0005
.002
.0002
]
]
]
]
23
-PACK TinMan High Speed,
A
2
4.00
± 0.05
[.945
± .002
]
15.40
[.606]
1.90
[
.075]
R
ef.
2.375
[
.094]
R
ef.
2
.20
± 0.15
[.087
± .006
]
1
5.30
[.602]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
9.00
± 0.13
[.354
± .005
]
Recommended PC Board Layout
Component Side Shown
6.80
[.268]
Ref.
6
.00
[.236]
Ref.
4
.50
[.177]
Ref.
15.40
[.606]
Ref.
B
0.90
[.035]
Ref.
0.90
[.035]
Ref.
1.95
[.077]
Ref.
2.10
[.083]
Ref.
1.90
[.075]
Typ.
18
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.80
[.071]
Ref.
1.40
[.055]
Ref.
1.70
[.067]
Ref.
1.40
[
.055]
R
ef.
Row A
Row A
Row L
Row K
Row J
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
15.80
[.622]
Ref.
+ 0.10
– 0.55
+ .004
– .022
20.20
[
.795
]
+ 0.08
–
0.20
+
.003
–
.008
1
8.40
[.724
]
2.65
[.104]
Ref.
Z
High Density Backplane Connector
4 Pair Right Angle Pin Header Assemblies — Double End Walls
imension
olumn Part Number
C
8 1934354-1
6 1934352-1
1
* Custom tooling not required. Utilizes flat-rock insertion tooling.
eference Application Specification 114-13202.
R
D
AB
18.05 13.30
.711 .524
3.25 28.50
3
.309 1.122
1
pplication
A
ooling
T
* 1934222-1
*
ates With
M
1934225-1
24
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
0.05
0.013
0.02
0.004
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
.001
.0005
.002
.0002
]
]
]
]
-PACK TinMan High Speed,
A
11.20
[.441]
1.90
[
.075]
R
ef.
0.625
[
.025]
R
ef.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
Recommended PC Board Layout
Component Side Shown
B
0.90
[.035]
Ref.
0.90
[.035]
Ref.
1.95
[.077]
Ref.
1.15
[.045]
Ref.
1.90
[.075]
Typ.
18
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.80
[.071]
Ref.
1.40
[.055]
Ref.
Row A
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
15.80
[.622]
Ref.
19.80
± 0.05
[.780
± .002
]
2.20
±
0.15
[.087
± .006
]
11.10
[.437]
Ref.
9
.00
± 0.13
[.354
± .005
]
6.80
[
.268]
R
ef.
6
.00
[.236]
Ref.
4.50
[.177]
Ref.
1
1.20
[.441]
Ref.
1.40
[
.055]
R
ef.
1.70
[
.067]
R
ef.
Row A
+ 0.10
– 0.55
+ .004
– .022
16.00
[
.630
]
+ 0.08
– 0.20
+ .003
– .008
1
4.20
[.559
]
Z
High Density Backplane Connector
3 Pair Right Angle Pin Header Assemblies
imension
olumn Part Number
C
8 1934359-1
10
6 1934355-1
1
Custom tooling not required. Utilizes flat-rock insertion tooling.
*
eference Application Specification 114-13202.
R
934357-1
1
D
AB
15.35 13.30
.604 .524
9.15 17.10
1
754 .673
.
0.55 28.50
3
.203 1.122
1
A
pplication
ooling
T
M
* 1934226-1
*
*
1934228-1
1934229-1
ates With
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
0.013
0.02
0.004
0.05
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
[.018 ±
.001
.0005
.002
.0002
]
]
]
]
25
-PACK TinMan High Speed,
A
19.80
± 0.05
[
.780
± .002
]
11.20
[.441]
1.90
[.075]
Ref.
2.375
[.094]
Ref.
2
.20
± 0.15
[.087
±
.006
]
11.10
[
.437]
Ref.
Finished Hole Size and
Plated Thru Holes*
Connector Outline
9.00
± 0.13
[.354
± .005
]
Recommended PC Board Layout
Component Side Shown
6.80
[
.268]
R
ef.
6
.00
[.236]
Ref.
4.50
[.177]
Ref.
1
1.20
[.441]
Ref.
B
0.90
[.035]
Ref.
0.90
[.035]
Ref.
1.95
[.077]
Ref.
2.10
[.083]
Ref.
1.90
[.075]
Typ.
18
Ref.
1.50
[.059]
Max.
1.40
[.055]
Typ.
1.80
[.071]
Ref.
1.40
[
.055]
R
ef.
1.70
[
.067]
R
ef.
1.40
[.055]
Ref.
Row A
Row A
Row I
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
-Y-
BSC
BSC
15.80
[.622]
Ref.
+
0.10
– 0.55
+ .004
– .022
16.00
[.630
]
+ 0.08
– 0.20
+ .003
– .008
14.20
[
.559
]
2.65
[.104]
Ref.
Z
High Density Backplane Connector
3 Pair Right Angle Pin Header Assemblies — Double End Walls
imension
olumn Part Number
C
8 1934360-1
10
6 1934356-1
1
Custom tooling not required. Utilizes flat-rock insertion tooling.
*
eference Application Specification 114-13202.
R
934358-1
1
D
AB
18.05 13.30
.711 .524
1.85 17.10
2
860 .673
.
3.25 28.50
3
.309 1.122
1
pplication
A
ooling
T
* 1934226-1
*
*
ates With
M
1934228-1
19343229-1
26
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC001-1.
0.05
0.013
0.02
0.004
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
.001
.0005
.002
.0002
]
]
]
]
Product Facts
■ Scalable to 25 Gbps
00 ohm impedance
■ 1
for differential pair
configuration
■ Very low noise
■ Outstanding insertion loss
through 2 connectors and
vias
■ Skewless differential pair
in a 2-connector system
■ Utilizes the same header
and receptacle part on both
sides of the mid-plane
■ Compatible with standard
Z-PACK TinMan connectors
and accessories
■ 4 pair x 4 pair and 6 pair x
6 pair modules available
■ Reliable, redundant contact
design on all contacts
■ Reliable press-fit style
termination to PCB
■ RoHS compliant
Applications
The Z-PACK TinMan Mid-plane
(orthogonal) connector is
ideally designed for very
demanding applications
involving data rates in excess
of 10 Gbps with many interconnections required. Such applications would include the
following Telecom/Datacom
equipment:
■ Switches
■ Servers
■ Routers
■ Storage
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview
The Z-PACK TinMan midplane (orthogonal) connector is an extension of the
Z-PACK TinMan connector
product line, which includes
perpendicular and coplanar
interconnect solutions in
3 pair, 4 pair, and 5 pair
versions.
This connector system is
commonly referred to as an
orthogonal connector system due to the orthogonal
(perpendicular) orientation
of the two system boards
being connected on the
front and rear side. It is
built on the same technology and design approach
as standard Z-PACK TinMan
connectors with the same
mating interface and leadframe geometry.
Superior electrical performance is achieved for several
reasons. The front board to
rear board connection
through the mid-plane
makes the plated through
hole (PTH) part of the signal
transmission path eliminating the detrimental effects
of via stubs. This construction also eliminates the
need to route all the high
speed signal lines along the
backplane minimizing signal loss and significantly
improving signal throughput. The wide column
spacing establishes a connector footprint with
improved impedance and
reduced electrical noise.
The in-line footprint version
also provides ease of trace
routing with wide channels
and a connector interface
compatible with the orthogonal receptacle. This
permits the use of the same
daughtercard in both
mid-plane and backplane
configurations.
The benefits are not limited
to just signal integrity performance. The thinner midplane with fewer layers and
significantly less complex
routing is inherently less
expensive. With trace
routing typically limited to
power distribution, low
speed lines and potentially
very few high speed links,
the board can be fabricated
from a cost effective material without the need to
utilize techniques such as
counter-boring or backdrilling.
All of this permits the implementation of small to large
scale full mesh interconnects with significantly
reduced complexity at a
lower cost and with
improved signal integrity.
For additional information visit:
6x6 (36 signal pairs)
http://www.tycoelectronics.com/zpacktinman
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
27
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview (Continued)
Noise Table
■ Maximum, multiple source
crosstalk
Technical Documents
Product Specification 108-2303
Application Specification
114-13202
Routing Guide Report #27GC002
aterial and Finish
M
Signal Contact — High Strength
Copper Alloy
Ground Contact — High Strength
Copper Alloy
Housing — Liquid Crystal Polymer
Platings — Telcordia compliant inter-
face, Nickel underplate
Compliant Pin Plating —
RoHS Compliant
Ratings
Temperature Range —
-65°C to +90°C
Current Rating — 0.5 A/contact @
< 30°C T-Rise
Durability — 200 cycles
Dielectric Withstanding Voltage —
560 VAC
Operating Voltage — 250 VAC max.
Signal Integrity
Characteristic Impedance —
Differential @ 100 ohms ±10%
Crosstalk — Multi-pair differential
crosstalk: 1.0% @ 50ps
Insertion Loss — -2 dB @ 10 GHz
otal Peak Receiver Noise
ICTIM
V
AB3 0.50%
CD3 1.00%
F3 0.90%
E
H3 0.80%
G
JK3 0.90%
M3 0.60%
L
Note: Data includes PCB vias of both backplane
nd daughtercard connectors.
a
ingle mated connector pair.
S
50 ps (20-80%) edge rate.
T
or Recommended Pin-Out
f
Insertion Loss Plot
28
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Representative Eye Pattern
■ 10.0 Gbps data rate
7
1 PRBS
■ 2
-
■ Unequalized Signal
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Z-PACK TinMan Mid-Plane (Orthogonal) Connector Overview (Continued)
Customer Connector
Evaluation Kit
■ Connector characterization
■ Available for loan — contact
your local Tyco Electronics
Sales Engineer
■ Time and frequency domain
testable
■ Testable to 18+ GHz (25+ Gb/s)
■ Multiple calibration options
■ Convenient SMA interface
Customer System
Evaluation Kit
■ System characterization
■ Available for loan — contact
your local Tyco Electronics
Sales Engineer
■ Time and frequency domain
testable
■ Testable to 18+ GHz (25+ Gb/s)
■ Multiple calibration options
■ Convenient SMA interface
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
29
6 Pair Right Angle
Finished Hole Size and
P
lated Thru Holes*
Connector Outline
1
1.00
[.433]
Recommended PC Board Layout
Component Side Shown
Ref.
0.10
[.004]
Ref.
12.50
[.492]
Ref.
21.00
[.827]
Ref.
Surface of
Mating Midplane
25.10
[.988]
R
ef.
21.60
[
.850]
R
ef.
1.70
[.067]
Ref.
1.80
[
.071]
R
ef.
1
.40
[.055]
Ref.
2
.625
[.103]
Ref.
1.475
[.058]
Ref.
1.21
[.048]
Ref.
1.80
[.071]
Typ.
2.10
[.083]
Typ.
1.50
[.059]
Max.
Position
A
1
4.20
[
.165]
R
ef.
Row M
Row L
Row K
Row J
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
4.20
[.165]
Typ.
BSC
BSC
-Y-
30.00
± 0.10
[
1.181
± .004
]
2
7.90
± 0.08
[1.098
±
.003
]
2.20
[.087]
R
ef.
32.40
[1.276]
Ref.
11.00
[.433]
Ref.
Receptacle Assembly
Part Number: 1934231-1
Custom tooling not required.
Utilizes flat-rock insertion
tooling.
Reference Application
Specification
14-13202
1
Mates with: 1934364-1,
1934363- 1
-PACK TinMan High Speed,
Z
High Density Backplane Connector
6 Pair Mid-Plane Assemblies
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC002.
30
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
6 Pair Vertical Header
2
7.50
± 0.05
[1.083
± .002
]
6
.00
± 0.15
[.236
±
.006
]
2.80
±
0.05
[
.110
± .002
]
11.80
± 0.10
[
.465
± .004
]
+ 0.10
– 0.55
+ .004
– .022
3
0.00
[1.181
]
Typ.
4.40
± 0.15
[.173
± .006
]
T
yp.
1.80
±
0.20
[
.071
± .008
]
1.90
± 0.20
[.075
± .008
]
F
inished Hole Size and
Plated Thru Holes*
Recommended PC Board Layout
Component Side Shown
25.20
[.992]
Ref.
25.20
[.992]
Ref.
T
yp.
T
yp.
FRONT
1 23456
M
L
K
J
H
G
F
E
D
C
B
A
Connector Outline
ssembly
A
Part Number: 1934364-1
Insertion Tooling:
Contact Tyco Electronics
Reference Application
Specification 114-13202
Mates with: 1934231-1
-PACK TinMan High Speed,
Z
High Density Backplane Connector
6 Pair Mid-Plane Assemblies (Continued)
Footprint shown for reference
only. Contact Tyco Electronics
engineering for details.
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC002.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
31
6 Pair Vertical Header
1
.40
[.055]
Ref.
2
7.50
± 0.05
[1.083
± .002
]
6.00
± 0.15
[
.236
± .006
]
2.80
± 0.05
[.110
± .002
]
11.80
± 0.10
[.465
± .004
]
+ 0.10
– 0.55
+ .004
– .022
3
0.00
[1.181
]
Typ.
4.50
± 0.15
[.177
± .006
]
T
yp.
1.80
± 0.20
[.071
± .008
]
2.40
[
.094]
R
ef.
ssembly — In Line
A
Footprint
Part Number: 1934363-1
Insertion Tooling:
Contact Tyco Electronics
Reference Application
Specification 114-13202
Mates with: 1934231-1
-PACK TinMan High Speed,
Z
High Density Backplane Connector
6 Pair Mid-Plane Assemblies (Continued)
Footprint shown for reference
only. Contact Tyco Electronics
engineering for details.
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide Report
#27GC002.
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
0.013
0.02
0.004
0.05
[.0015 ±
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
32
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
4 Pair Right Angle
F
inished Hole Size and
Plated Thru Holes*
C
onnector Outline
11.00
[
.433]
Recommended PC Board Layout
Component Side Shown
R
ef.
0.10
[.004]
Ref.
12.50
[.492]
Ref.
12.60
[.496]
Ref.
Surface of
Mating Midplane
1
6.70
[.657]
Ref.
21.60
[
.850]
R
ef.
1.70
[.067]
Ref.
1.80
[
.071]
R
ef.
1
.40
[.055]
Ref.
2.625
[
.103]
R
ef.
1
.475
[.058]
Ref.
1
.21
[.048]
Ref.
1.80
[.071]
Typ.
2.10
[.083]
Typ.
1.50
[.059]
Max.
Position A1
4
.20
[.165]
Ref.
Row H
Row G
Row F
Row E
Row D
Row C
Row B
Row A
-X-
4.20
[.165]
Typ.
BSC
BSC
-Y-
21.60
± 0.10
[.850
±
.004
]
19.50
± 0.08
[.768
± .003
]
21.60
[.850]
Ref.
11.00
[.433]
Ref.
2.20
[.087]
Ref.
Receptacle Assembly
Part Number: 1934230-1
Custom tooling not required.
Utilizes flat-rock insertion
tooling.
Reference Application
Specification 114-13202
Mates with: 1934362-1,
1934361-1
-PACK TinMan High Speed,
Z
High Density Backplane Connector
4 Pair Mid-Plane Assemblies
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC002.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
0.013
0.02
0.004
0.05
[.018 ±
[.022 ±
[.0015 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
33
Pair Vertical Header
19.10
± 0.05
[
.752
±
.002
]
6.00
± 0.15
[
.236
±
.006
]
2.80
±
0.05
[.110
± .002
]
11.80
±
0.10
[
.465
± .004
]
+
0.10
–
0.55
+
.004
–
.022
2
1.60
[.850
]
Typ.
4.40
±
0.15
[.173
± .006
]
T
yp.
T
yp.
T
yp.
1.80
± 0.20
[
.071
± .008
]
1
.90
± 0.20
[.075
± .008
]
Finished Hole Size and
P
lated Thru Holes*
Recommended PC Board Layout
Component Side Shown
BSC
BSC
16.80
[.691]
Ref.
16.80
[.691]
Ref.
FRONT
1234
H
G
F
E
D
C
B
A
Connector Outline
4
Assembly
Part Number: 1934362-1
Insertion Tooling:
Contact Tyco Electronics
Reference Application
Specification 114-13202
Mates with: 1934230-1
-PACK TinMan High Speed,
Z
High Density Backplane Connector
4 Pair Mid-Plane Assemblies (Continued)
Footprint shown for reference
only. Contact Tyco Electronics
engineering for details.
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC002.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
34
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
Pair Vertical Header
Recommended PC Board Layout
Component Side Shown
BSC
19.10
± 0.05
[
.752
±
.002
]
6.00
± 0.15
[.236
± .006
]
2.80
± 0.05
[.110
±
.002
]
BSC
16.80
[.661]
Ref.
12.60
[.496]
Ref.
11.80
±
0.10
[
.465
± .004
]
+ 0.10
– 0.55
+ .004
– .022
21.60
[.850
]
Typ.
4
.50
± 0.15
[
.177
± .006
]
Typ.
Typ.
1.80
± 0.20
[
.071
± .008
]
2
.40
[.094]
Ref.
1.40
[
.055]
R
ef.
1234
H
G
F
E
D
C
B
A
Connector Outline
4
Assembly — In Line
Footprint
art Number: 1934361-1
P
Insertion Tooling:
Contact Tyco Electronics
Reference Application
Specification 114-13202
Mates with: 1934230-1
-PACK TinMan High Speed,
Z
High Density Backplane Connector
4 Pair Mid-Plane Assemblies (Continued)
Footprint shown for reference
only. Contact Tyco Electronics
engineering for details.
Note: For additional information
on pcb routing guidelines,
reference the Z-PACK TinMan
Connector Routing Guide
Report #27GC002.
* Finished Hole Diameter = 0.46 ±
Drilled Hole Diameter = 0.55 ±
Copper Thickness = 0.038 ±
Tin-Lead Thickness = 0.008 ±
0.013
0.004
0.05
0.02
[.0015 ±
[.018 ±
[.022 ±
[.0003 ±
.001
.0005
.002
.0002
]
]
]
]
Finishes other than Tin-Lead, See Appl. Spec. 114-13202
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
35
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Z-PACK TinMan Product Mating Sequence Chart
Fully Mated Reliable Mate
im. A
Product
Family
Z-PACK HM-Zd
roduct
P
-PACK HM-Zd
Z
Guide
Hardware
Z-PACK TinMan
Product
-PACK 2mm HM
Z
Product
MULTIGIG RT
T1
Product
MULTIGIG RT
T2
Product
MULTIGIG RT
T3
Product
MULTIGIG RT
Power
Module
MULTIGIG RT
Guide N/A
Hardware
Z-PACK HS3
Product
UPM
UPM
Guide
Hardware
MULTI-BEAM XL
Right Angle
Header to
Vertical
Receptacle
MULTI-BEAM XL
Right Angle
Receptacle
to Vertical
Header
Dim. C Fully Contact
1.50 12.50
.059 .492
3
.118 .492
1.50 12.50
.059 .492
1.50 12.50
059 .492
.
2.50 12.50
.098 .492
2.25 12.50
.089 .492
2.25 12.50
.089 .492
5.50 12.50
.217 .492
1.50 12.50
.059 .492
3.50 12.50
.138 .492
5.75 12.50
.226 .492
5.08 14.73
.200 .580
3.81 13.21
.150 .520
D
Mated
.00 12.50
12.50
.492
Ground Shield 16.78 [.661] 17.55 [.691] 4.28 [.169]
Signal Level 2 15.41 [.607] 15.85 [.624] 2.91 [.115]
ignal Level 1 13.91 [.548] 14.35 [.565] 1.41 [.056]
S
4.0 mm Pin 27.50 [1.083] 33.40 [1.315] N/A
2
22.2 mm Pin 25.70 [1.012] 31.60 [1.244] N/A
Key Blocking Point N/A 22.03 [.867] N/A
round Pins 16.44 [.647] 17.13 [.674] 3.94 [.155]
G
Signal Level 2 14.94 [.588] 15.63 [.615] 2.44 [.096]
Signal Level 1 N/A N/A N/A
ignal Level 3 18.27 [.719] 18.84 [.742] 5.77 [.227]
S
ignal Level 2 16.77 [.660] 17.34 [.683] 4.27 [.168]
S
Signal Level 1 15.27 [.601] 15.84 [.624] 2.77 [.109]
Ground 18.00 [.709] — 5.50 [.217]
Signal Level 3 18.00 [.709] — 5.50 [.217]
Signal Level 2 16.50 [.650] — 4.00 [.157]
Signal Level 1 15.00 [.591] — 2.50 [.098]
Ground 18.00 [.709] — 5.50 [.217]
Signal Level 3 18.00 [.709] — 5.50 [.217]
Signal Level 2 16.50 [.650] — 4.00 [.157]
Signal Level 1 15.00 [.591] — 2.50 [.098]
Ground 16.50 [.650] — 4.00 [.157]
Signal Level 1 15.00 [.591] — 2.50 [.098]
Power Level 3 23.75 [.935] — 11.25 [.443]
Power Level 2 22.25 [.876] — 9.75 [.384]
Power Level 1 20.75 [.817] — 8.25 [.325]
Guide Pin Key 33.25 [1.309] N/A 20.75 [.817]
Guide ESD Contact 30.75 [1.211] — 18.25 [.719]
Ground 17.08 [.672] 17.60 [.693] 4.78 [.188]
Signal Level 2 16.05 [.632] 16.47 [.648] 3.75 [.148]
Signal Level 1 14.55 [.573] 14.97 [.589] 2.25 [.089]
Power Level 3 20.25 [.797] 20.95 [.825] 8.10 [.319]
Power Level 2 18.65 [.734] 19.35 [.762] 6.50 [.256]
Power Level 1 17.03 [.670] 17.73 [.698] 4.88 [.192]
Guide Pin Key 31.39 [1.236] 36.16 [1.424] N/A
Keyed Guide Pin 31.39 [1.236] 36.16 [1.424] N/A
Keyed Guide Pin 35.23 [1.387] 40.00 [1.575] N/A
PreMate Power — 5.61 [.221]
Level 1
PostMate Power — 4.34 [.171]
Level 2
PreMate Signal — 3.81 [.150]
Level 2
PostMate Signal — 2.54 [.100]
Level 3
PreMate Power — 5.61 [.221]
Level 1
PostMate Power — 4.34 [.171]
Level 2
PreMate Signal — 3.81 [.150]
Level 2
PostMate Signal — 2.54 [.100]
Level 3
36
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
Dim B.
eliable First Mate
R
ate Last Break
M
— 16.84 [.663]
— 17.81 [.701]
— 18.26 [.719]
— 19.53 [.769]
— 15.32 [.603]
— 16.28 [.641]
— 16.74 [.659]
— 18.01 [.709]
Fully Mated
Wipe Length
Min.
Min.
Min.
Min.
Min.
Min.
Min.
Min.
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Z-PACK MAX Connector to Z-PACK TinMan Connector
Base Part Number Cross Reference*
-PACK MAX Z-PACK TinMan
Z
onnector Base Connector Base Description
C
art Number Part Number
P
1469659 1934218 Receptacle Assembly, 5 pair, Standard, 8 Column
469660 1934269 Header Assembly, Open Ended, 5 Pair 8 Column
1
469680 1934272 Header Assembly, Left Wall, 5 Pair 8 Column
1
1469680 1934273 Header Assembly, Right Wall, 5 Pair 8 Column
1469681 1934271 Header Assembly, Double Wall, 5 Pair 8 Column
469687 1934315 Header Assembly, Open Ended, 4 Pair 16 Column
1
469693 1934225 Receptacle Assembly, 4 pair, Standard, 16 Column
1
1469702 1934303 Header Assembly, Left Wall, 4 Pair 8 Column
1469702 1934304 Header Assembly, Right Wall, 4 Pair 8 Column
469703 1934317 Header Assembly, Left Wall, 4 Pair 16 Column
1
1469703 1934318 Header Assembly, Right Wall, 4 Pair 16 Column
1469706 1934306 Header Assembly, Double Wall, 4 Pair 8 Column
469707 1934316 Header Assembly, Double Wall, 4 Pair 16 Column
1
469716 1934305 Header Assembly, Open Ended, 4 Pair 8 Column
1
1469717 1934222 Receptacle Assembly, 4 pair, Standard, 8 Column
1469735 1934349 Right Angle Header Assembly, Open Ended, 5 Pair 8 Column
469737 1934350 Right Angle Header Assembly, Double Wall, 5 Pair 8 Column
1
1469753 1934331 Header Assembly, Open Ended, 5 Pair 16 Column
1469754 1934221 Receptacle Assembly, 5 pair, Standard, 16 Column
469755 1934333 Header Assembly, Left Wall, 5 Pair 16 Column
1
469755 1934334 Header Assembly, Right Wall, 5 Pair 16 Column
1
1469756 1934332 Header Assembly, Double Wall, 5 Pair 16 Column
1469768 1934305 Header Assembly, Open Ended, 4 Pair 8 Column
1469769 1934222 Receptacle Assembly, 4 pair, Standard, 8 Column
1469774 1934311 Header Assembly, Open Ended, 4 Pair 10 Column
1469775 1934224 Receptacle Assembly, 4 pair, Standard, 10 Column
1469784 1934362 4x4 Orthogonal Offset Header Assembly, Double Wall
1469785 1934230 Receptacle Assembly, 4x4, Orthogonal
1469786 1934364 6x6 Orthogonal Offset Header Assembly, Double Wall
1469787 1934231 Receptacle Assembly, 6x6, Orthogonal
1469788 1934311 Header Assembly, Open Ended, 4 Pair 10 Column
1469789 1934224 Receptacle Assembly, 4 pair, Standard, 10 Column
1469793 1934353 Right Angle Header Assembly, Open Ended, 4 Pair 8 Column
1469795 1934354 Right Angle Header Assembly, Double Wall, 4 Pair 8 Column
1469807 1934339 Header Assembly, Open Ended, 3 Pair 10 Column
1469809 1934228 Receptacle Assembly, 3 pair, Standard, 10 Column
1469827 1934339 Header Assembly, Open Ended, 3 Pair 10 Column
1469828 1934228 Receptacle Assembly, 3 pair, Standard, 10 Column
1469829 1934299 Header Assembly, Open Ended, 3 Pair 8 Column
1469831 1934226 Receptacle Assembly, 3 pair, Standard, 8 Column
1469853 1934335 Header Assembly, Open Ended, 3 Pair 6 Column
1469854 1934227 Receptacle Assembly, 3 pair, Standard, 6 Column
1469867 1934340 Header Assembly, Left Wall, 3 Pair 10 Column
1469867 1934341 Header Assembly, Right Wall, 3 Pair 10 Column
1469871 1934357 Right Angle Header Assembly, Open Ended, 3 Pair 10 Column
1469874 1934358 Right Angle Header Assembly, Double Wall, 3 Pair 10 Column
1469935 1934342 Header Assembly, Double Wall, 3 Pair 10 Column
1469945 1934300 Header Assembly, Left Wall, 3 Pair 8 Column
1469945 1934301 Header Assembly, Right Wall, 3 Pair 8 Column
1469946 1934302 Header Assembly, Double Wall, 3 Pair 8 Column
1469949 1934343 Header Assembly, Open Ended, 3 Pair 16 Column
1469950 1934344 Header Assembly, Left Wall, 3 Pair 16 Column
1469950 1934345 Header Assembly, Right Wall, 3 Pair 16 Column
1469951 1934346 Header Assembly, Double Wall, 3 Pair 16 Column
1469955 1934229 Receptacle Assembly, 3 pair, Standard, 16 Column
1469960 1934335 Header Assembly, Open Ended, 3 Pair 6 Column
*As announced on 6/20/07, Tyco Electronics now offers the Z-PACK TinMan product line as a form, fit and function
replacement to the Z-PACK MAX product line. This char t will assist in finding the Z-PACK TinMan connector
part number if you have a Z-PACK MAX connector par t number.
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
37
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Z-PACK MAX Connector to Z-PACK TinMan Connector
Base Part Number Cross Reference*
-PACK MAX Z-PACK TinMan
Z
onnector Base Connector Base Description
C
art Number Part Number
P
469961 1934336 Header Assembly, Left Wall, 3 Pair 6 Column
1
469961 1934337 Header Assembly, Right Wall, 3 Pair 6 Column
1
1469962 1934338 Header Assembly, Double Wall, 3 Pair 6 Column
1469966 1934227 Receptacle Assembly, 3 pair, Standard, 6 Column
469974 1934359 Right Angle Header Assembly, Open Ended, 3 Pair 8 Column
1
469977 1934360 Right Angle Header Assembly, Double Wall, 3 Pair 8 Column
1
1934007 1934321 Header Assembly, Open Ended, 5 Pair 6 Column
1934008 1934323 Header Assembly, Left Wall, 5 Pair 6 Column
934008 1934324 Header Assembly, Right Wall, 5 Pair 6 Column
1
1934009 1934322 Header Assembly, Double Wall, 5 Pair 6 Column
1934010 1934219 Receptacle Assembly, 5 pair, Standard, 6 Column
934018 1934347 Right Angle Header Assembly, Open Ended, 5 Pair 16 Column
1
934021 1934348 Right Angle Header Assembly, Double Wall, 5 Pair 16 Column
1
1934026 1934351 Right Angle Header Assembly, Open Ended, 4 Pair 16 Column
1934029 1934352 Right Angle Header Assembly, Double Wall, 4 Pair 16 Column
934034 1934355 Right Angle Header Assembly, Open Ended, 3 Pair 16 Column
1
1934037 1934356 Right Angle Header Assembly, Double Wall, 3 Pair 16 Column
1934106 1934313 Header Assembly, Left Wall, 4 Pair 10 Column
934106 1934314 Header Assembly, Right Wall, 4 Pair 10 Column
1
934107 1934312 Header Assembly, Double Wall, 4 Pair 10 Column
1
1934121 1934364 6x6 Orthogonal Offset Header Assembly, Double Wall
1934122 1934231 Receptacle Assembly, 6x6, Orthogonal
1934127 1934220 Receptacle Assembly, 5 pair, Standard, 10 Column
1934136 1934315 Header Assembly, Open Ended, 4 Pair 16 Column
1934137 1934317 Header Assembly, Left Wall, 4 Pair 16 Column
1934137 1934318 Header Assembly, Right Wall, 4 Pair 16 Column
1934141 1934363 6x6 Orthogonal In-Line Header Assembly, Double Wall
1934165 1934361 4x4 Orthogonal In-Line Header Assembly, Double Wall
1934171 1934275 Receptacle Assembly, 4 pair, Standard, 14 Column
1934194 1934325 Header Assembly, Open Ended, 5 Pair 10 Column
1934208 1934326 Header Assembly, Double Wall, 5 Pair 10 Column
1934210 1934327 Header Assembly, Left Wall, 5 Pair 10 Column
1934210 1934328 Header Assembly, Right Wall, 5 Pair 10 Column
N/A 1934223 Receptacle Assembly, 4 pair, Standard, 6 Column
N/A 1934274 Header Assembly 5 Pair Open Ended 8 Column Notched Wall
N/A 1934276 Receptacle Assembly, 5 pair, Standard, 14 Column
N/A 1934287 Header Assembly, Open Ended, 5 Pair 14 Column
N/A 1934288 Header Assembly, Open Ended, 4 Pair 14 Column
N/A 1934289 Header Assembly, Double Wall, 5 Pair 14 Column
N/A 1934290 Header Assembly, Double Wall, 4 Pair 14 Column
N/A 1934307 Header Assembly, Open Ended, 4 Pair 6 Column
N/A 1934308 Header Assembly, Double Wall, 4 Pair 6 Column
N/A 1934309 Header Assembly, Left Wall, 4 Pair 6 Column
N/A 1934310 Header Assembly, Right Wall, 4 Pair 6 Column
N/A 1934319 Header Assembly, Left Wall, 4 Pair 14 Column
N/A 1934320 Header Assembly, Right Wall, 4 Pair 14 Column
N/A 1934329 Header Assembly, Left Wall, 5 Pair 14 Column
N/A 1934330 Header Assembly, Right Wall, 5 Pair 14 Column
(Continued)
*As announced on 6/20/07, Tyco Electronics now offers the Z-PACK TinMan product line as a form, fit and function
replacement to the Z-PACK MAX product line. This char t will assist in finding the Z-PACK TinMan connector
part number if you have a Z-PACK MAX connector par t number.
38
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
-PACK TinMan High Speed,
Z
High Density Backplane Connector
Part Number Index
Note: This index lists all cataloged parts
y base no. only. Complete part nos. (with
b
prefixes and/or suffixes) are shown on the
age(s) indicated.
p
art No. Page
P
1934218 6
1934221 6
934222 7
1
934225 7
1
1934226 8
934228 8
1
934229 8
1
1934230 33
1934231 30
934269 9
1
934271 12
1
1934272 10
1934273 11
934299 17
1
1934300 18
1934301 19
934302 20
1
934303 14
1
1934304 15
art No. Page
P
1934305 13
1934306 16
934315 13
1
934316 16
1
1934317 14
934318 15
1
934331 9
1
1934332 12
1934333 10
934334 11
1
934339 17
1
1934340 18
1934341 19
934342 20
1
1934343 17
1934344 18
934345 19
1
934346 20
1
1934347 21
art No. Page
P
1934348 22
1934349 21
934350 22
1
934351 23
1
1934352 24
934353 23
1
934354 24
1
1934355 25
1934356 26
934357 25
1
934358 26
1
1934359 25
1934360 26
934361 35
1
1934362 34
1934363 32
934364 31
1
Tooling Part Number Index
Note: This index lists all cataloged parts
by base no. only. Complete part nos. (with
prefixes and/or suffixes) are shown on the
page(s) indicated.
Catalog 5-1773447-9 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-2103-6000
Revised 7-07 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-1106-0803 UK: 44-8706-080-208
Part No. Page
1804790 13, 14, 15, 16
1804791 9, 10, 11, 12
1901457 17, 18, 19, 20
39
Americas
Argentina – Buenos Aires
hone: +54-11-4733-2200
P
Fax: +54-11-4733-2211
rasil – São Paulo
B
Phone: +55-11-3611-1311
Fax: +55-11-3611-0397
Asia/Pacific
Australia – Sydney
Phone: +61-2-9554-2600
ax: +61-2-9502-2556
F
Product Information Center:
(Technical Support)
hone: +61-2-9840-8200
P
Fax: +61-2-9634-6188
India – Bangalore
Phone: +91-80-285-40800
ax: +91-80-285-40820
F
Indonesia – Jakarta
hone: +65-6482-0311
P
Fax: +65-6482-1012
Canada – Toronto
hone: +905-475-6222
P
Fax: +905-474-5520
Product Information Center:
Technical Support)
(
Phone: +905-470-4425
Fax: +905-474-5525
Colombia – Bogota
Phone: +57-1-231-9398
ax: +57-1-660-0206
F
Japan – Toyko
Phone: +81-44-844-8111
ax: +81-44-812-3207
F
Product Information Center:
(Technical Support)
hone: +81-44-844-8013
P
Fax: +81-44-812-3200
Korea – Seoul
Phone: +82-2-3415-4500
ax: +82-2-3486-3810
F
Malaysia – Kuala Lumpur
hone: +60-3-78053055
P
Fax: +60-3-78053066
Mexico – Mexico City
hone: +52-55-1106-0800
P
Fax: +52-55-1106-0901
United States – Harrisburg, PA
Phone: +717-564-0100
F
Product Information Center:
(Technical Support)
P
Fax: +717-986-7575
New Zealand – Auckland
Phone: +64-9-634-4580
F
Philippines – Makati City
Phone: +632-848-0171
F
P
Hong Kong
P
Fax: +852-2735-0243
Shanghai
Phone: +86-21-2407-1588
F
Taiwan – Taipei
P
Fax: +886-2-8768-2268
+01-800-733-8926
ax: +717-986-7575
hone: +800-522-6752
ax: +64-9-634-4586
ax: +632-867-8661
eople’s Republic of China
hone: +852-2735-1628
ax: +86-21-2407-1599
hone: +886-2-8768-2788
Global Contacts
For Latin/South American
ountries not shown
C
Phone: +54-11-4733-2015
Fax: +54-11-4733-2083
Singapore – Singapore
hone: +65-6482-0311
P
Fax: +65-6482-1012
hailand – Bangkok
T
Phone: +66-2-955-0500
Fax: +66-2-955-0505
Vietnam and Indochina –
o Chi Minh City
H
Phone: +84-8 930-5546
Fax: +84-8 930-3443
Europe/Middle East/Africa
Austria – Vienna
Phone: +43-1 90 5 60-0
Fax: +43-1 90 5 60-1333
Belgium – Kessel-Lo
Phone: +32-16-35-23-00
Fax: +32-16-35-23-52
Bulgaria – Sofia
Phone: +359-2-971-2152
Fax: +359-2-971-2153
Czech Republic – Kurim
Phone: +420-5-41-162-111
Fax: +420-5-41-162-223
Denmark – Glostrup
Phone: +45-43-480-452
Fax: +45-43-441-414
Egypt – Cairo
Phone: +20-2-29 04 281
Fax: +20-2-41 92 334
Estonia – Tartu
Phone: +372-5138-274
Fax: +372-7400-779
Finland – Helsinki
Phone: +358-95-12-34-20
Fax: +358-95-12-34-250
France – Cergy-Pontoise
Phone: +33-1-3420-8888
Fax: +33-1-3420-8600
Product Information Center:
(Technical Support)
Phone: +33-1-3420-8943
Fax: +33-1-3420-8623
Germany – Bensheim
Phone: +49-6251-133-0
Fax: +49-6251-133-1600
Product Information Center:
(Technical Support)
Phone: +49-6251-133-1999
Fax: +49-6251-133-1988
Germany – Langen
Phone: +49-6103-709-0
Fax: +49-6103-709-1223
Germany – Speyer
Phone: +49-6232-30-0
Fax: +49-6232-30-2243
Germany - HTS Division – Neunkirchen
Phone: +49-2247-305-0
Fax: +49-2247-305-122
Greece – Athens
Phone: +30-210-9370-396/397
Fax: +30-210-9370-655
Hungary – Budapest
Phone: +36-1-289-1000
Fax: +36-1-289-1010
Ireland – Dublin
Phone: +353-1-820-3000
Fax: +353-1-820-9790
Israel – Yokneam
Phone: +972-4-959-0508
Fax: +972-4-959-0506
Italy – Collegno (Torino)
Phone: +39-011-4012-111
Fax: +39-011-4031116
Lithuania – Vilnius
Phone: +370-5-2131-402
Fax: +370-5-2131-403
Netherlands – ’s-Hertogenbosch
Phone: +31-73-624-62-46
Fax: +31-73-621-23-65
Product Information Center:
(Technical Support)
Phone: +31-73-6246-999
Fax: +31-73-6246-998
Norway – Nesbru
Phone: +47-66-77-8886
Fax: +47-66-77-8855
Poland – Warsaw
Phone: +48-22-45-76-700
Fax: +48-22-45-76-720
Romania – Bucharest
Phone: +40-21-311-3479/3596
Fax: +40-21-312-0574
Russia – Moscow
Phone: +7-495-926-5506/07/08/09
Fax: +7-495-926-5505
Russia – St. Petersburg
Phone: +7-812-718-8192
Fax: +7-812-718-8193
Slovenia – Ljubljana
Phone: +386-1561-3270
Fax: +386-1561-3240
South Africa – Port Elizabeth
Phone: +2741-503-4500
Fax: +2741-581-0440
Spain – Barcelona
Phone: +34-93-291-0330
Fax: +34-93-201-7879
Product Information Center:
(Technical Support):
Phone: +34-93-291-0330
Fax: +34-93-200-3779
Sweden – Upplands Väsby
Phone: +46-8-50-72-50-00
Fax: +46-8-50-72-50-01
Switzerland – Steinach
Phone: +41-71-447-0447
Fax: +41-71-447-0444
Turkey – Istanbul
Phone: +90-212-281-8181/2/3
Fax: +90-212-281-8184
Ukraine – Kiev
Phone: +380-044-206-2265
Fax: +380-044-206-2264
United Kingdom – Swindon
Phone: +44-8706-080-208
Fax: +44-1793-572-516
Product Information Center:
(Technical Support)
Freephone GB: 0800-267-666
Phone: +44-8706-080-208
Fax: +44-208-420-8081
For Middle East/African Countries
Not Shown
Phone: +33-1-3420-8866
Fax: +33-1-3420-8300
5-1773447-9–LUG–PDF–7-07 Tyco Electronics Corporation
Printed in the U.S.A. www.tycoelectronics.com