TYCO V23072-C1061-A303, V23072-C1062-A303 Specification

Page 1

Automotive Relays PCB Relays

Mini Relay K (Open – Sealed)

Limiting continuous current 20A

24VDC coil versions available

Typical applications Car alarm, hazard warning signal, heated rear screen, immobilizer, lamps front/rear, fog light, interior lights, sun roof, turn signal, wiper control.

F072A/C_fcw2b

Contact Data

Load resistive/inductive resistive/inductive resistive/inductive head/indicator head/indicator load load load lamp lamp V23072-C10**-A302 V23072-C10**-A303 V23072-C10**-A308 V23072-C1061-A402 V23072-C1061 A408 Contact arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form U/X, 2 NO 1 form A, 1 NO 1 form U/X, 2 NO Rated voltage 12VDC 12VDC 12VDC 12VDC 12VDC Rated current 15A 10/15A 2x10A 12A 2x6A Limiting continuous current 23°C 15A 10/15A 2x10A 12A 2x6A 85°C 10A 5/10A 2x6A 10A 2x5A Limiting making current Limiting breaking current 20A 10/20A 2x20A 6A 12A Contact material AgNi0.15 AgNi0.15 AgNi0.15 AgSnO.2 AgSnO.2 Min. recommended contact load Initial voltage drop at 10A, typ./max. 50/300mV 50/300mV 2x50/300mV 150/300mV 150/300mV Operate/release time max. typ. 3/1.5ms Electrical endurance >2x105 ops. >2x105 ops. >2x105 ops. >1x106 ops. >1.5 x 106 ops. at 13.5VDC, 10A at 13.5VDC, 10A at 13.5VDC, 10A up to 6x21W up to 6x21W >1.5x10 100A (on), 10 A (off) 100A (on), 10A (off) high beam high beam

1) The values apply to a resistive load or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC and 27VDC for 24VDC load voltages.

2) For a load current duration of maximum 3s for a make/break ratio of 1:10.

3) Corresponds to the peak inrush current on initial actuation (cold ﬁlament).

4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes

5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding (monostable version only).

1)2)

60A NC/NO 12/60A 2x40A 60A3) 120A3)

1A at 5VDC 1A at 5VDC 1A at 5VDC 1A at 5VDC 1A at 5VDC

ops. >7.5x105 ops.

Max. DC load breaking capacity

Datasheets and product speciﬁcation according to IEC 61810-1 and to be used only together with the ‘Deﬁnitions’ section.

Load limit curve 1: safe shutdown, connected as form X, load on pin 5 and 7. Load limit curve 2: safe shutdown, no stationary arc (NO contact). Load limit curve 3: arc extinguishes during transit time (CO contact). Load limit curves measured with low inductive resistors veriﬁed for 1000 switching events.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Deﬁnitions’ section, available at http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ section, application notes and all speciﬁcations are subject to change.

Page 2

Automotive Relays

Does not take into account the temperature rise due to the contact current E = pre-energization

TE1111-U1

TE1077-B1

TE1116-11

PCB Relays

Mini Relay K (Open – Sealed) (Continued)

Coil Data

Rated coil voltage 12VDC, 24VDC

Coil versions, DC coil

Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC Ω±10% W 061 12 6.9 1.2 130 1.1 062 24 14.1 2.4 520 1.1

All ﬁgures are given for coil without pre-energization, at ambient temperature +23°C.

Coil operating range

Other Data

EU RoHS/ELV compliance compliant Degree of protection IEC 61810 RT II – open (V23072-A), RT III – imm. cleanable (V23072-C) Climatic cycling with condensation EN ISO 6988 20 cycles, storage 8/16h Temperature cycling (shock) IEC 60068-2-14, Na 720 cycles, -40/+85°C (dwell time 1h) Damp heat constant IEC 60068-2-3, Ca 56 days, upper air temperatue 55°C Corrosive gas IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional) IEC 60068-2-6 (sine sweep), 10 to 200Hz, 23 to 35g Shock resistance (functional) IEC 60068-2-27 (half sine), 4 to 6ms 23 to 280g Terminal type PCB Weight, open/sealed approx. 8/9g (0.28/0.32oz) Solderability (aging 3: 4h/155°C) IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C Sealing, IEC 60068-2-17 Qc, method 2, 1min/70°C Storage conditions according IEC 600688 Packaging unit open 600 pcs. sealed 504 pcs.

6) Values weekest direction. Depending on mounting position: no change in the switching state >10μs.

7) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Deﬁnitions or at http://relays.te.com/appnotes/

Does not take into account the temperature rise due to the contact current E = pre-energization.

Terminal Assignment (Open and Sealed version)

Bottom view on solder pins

1 form A, NO

1 form U/X, 2 NO

1 form C, CO

Datasheets and product speciﬁcation according to IEC 61810-1 and to be used only together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Deﬁnitions’ section, available at http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ section, application notes and all speciﬁcations are subject to change.

Page 3

Automotive Relays

ø 1.3 +0.1

The Nipp-off-pin may be

PCB Relays

Dimensions

Mini Relay K Open Version

13.0 ±0.2

3.5 ±0.3 *)

Additional tin tops

max. 1 mm

9.5 ±0.2

17.5 ±0.5

4.0 ±1.0

View of the terminals (bottom view)

ø0.85 ±0.05

ø 3.5

15.0 ±1.0

6.7 ± 0.3

Mini Relay K (Open – Sealed)

Mini Relay K Sealed Version

14.5 ±0.4

0.2 – 1.4

Terminals tinned

0.9 ±0.15

6.1 ±0.3

TE0595-Z2

14.7 ±0.3

additional tin tops

max. 1 mm

View of the terminals (bottom view)

(Continued)

Assembly and positioning aid

19.2 ±0.3

3.0 ±0.3 *)

Nipp-off-pin

0.3 ±0.2

1.9 ±0.2

16.9 ±0.3 removed after soldering

and washing (for ventilation)

0.45 ±0.4

Terminals tinned

TE1112-32

0.85 ±0.06

0.75 ±0.06 0.55 ±0.05

PCB Layout

Bottom view on solder pins, grid 1.25 to 1.27mm

ø 1.3 +0.1

1.0 ±0.45

2.3 max.

1.2 ±0.4

4x 0.85 ±0.06

TE2209-U2

1.25 – 1.27

1.42 ±0.25

TE0596-82

2 x ø0.85 ±0.05

ø2.0 ±0.1

4.6 ±0.2

9.0 ±0.2

0.85 ±0.06

0.75 ±0.06

4x 0.55 ±0.05

PCB Layout

Bottom view on solder pins, grid 1.25 to 1.27mm

2.7 ±0.4

0.85 ±0.06

TE2210-X2

1.25 – 1.27

2.4 ±0.6

TE0598-P2

Datasheets and product speciﬁcation according to IEC 61810-1 and to be used only together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Deﬁnitions’ section, available at http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ sec-

tion, application notes and all speciﬁcations are subject to change.

Page 4

Automotive Relays PCB Relays

Mini Relay K (Open – Sealed)

Product code structure Typical product code V23072 -A 1 061 -A 30 2

Type V23072 Mini Relay K (Open – Sealed) Terminal and enclosure A PCB, open (RT II) C PCB, sealed (RT III – immersion cleanable) Design 1 Standard Coil 061 12 VDC 062 24 VDC Contact type A Standard Contact material 30 AgNi0.15 40 AgSnO Contact arrangement

2 1 form A, NO 3 1 form C, CO 8 1 form U/X, 2 NO

(Continued)

Product code Terminal/Encl. Design Coil Contact type Cont. material Arrangement Part number

V23072-A1061-A303 PCB, open Single relay V23072-A1062-A303 24VDC 5-1393272-2 V23072-A1061-A308 12VDC V23072-A1062-A308 24VDC 5-1393272-3 V23072-C1061-A302 12VDC V23072-C1062-A302 V23072-C1061-A303 12VDC V23072-C1062-A303 V23072-C1062-A303-EV-USBX V23072-C1061-A308 12VDC V23072-C1062-A308 24VDC 8-1393273-2 V23072-C1061-A402 V23072-C1061-A408

*) Americas market only.

PCB, sealed

12VDC

24VDC 7-1393273-6

24VDC

12VDC

Standard AgNi0.15 1 form C, CO 3-1393272-2

3-1393272-6

4-1393273-9

5-1393273-6

2-1414939-5 6-1393273-0

2-1416001-0 1-1416001-4

1 form U/X, 2 NO

1 form A, NO

7-1393273-8

AgSnO

1 form C, CO

1 form U/X, 2 NO

1 form A, NO

1 form U/X, 2 NO

Datasheets and product speciﬁcation according to IEC 61810-1 and to be used only together with the ‘Deﬁnitions’ section.

Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Deﬁnitions’ section, available at http://relays.te.com/definitions

Datasheets, product data, ‘Deﬁnitions’ section, application notes and all speciﬁcations are subject to change.