Tyco TY-L, TY3113, TY4113, TY3211, TY4211 Series Manual

Worldwide

Contacts

www.tyco-fire.com

Series TY-L — 5.6 and 8.0 K-factor
Upright and Pendent Intermediate Level Sprinklers
Standard Response

General
Description

The Series TY-L, 5.6 and 8.0 K-fac­tor Upright and Pendent Intermedi­ate Level Sprinklers described in this
data sheet are automatic sprinklers
of the “standard response” solder
type. They are “standard spray” sprin­klers intended for use in fire sprinkler
systems designed in accordance with
the standard installation rules rec­ognized by the applicable Listing or
Approval agency (e.g., UL Listing is
based on NFPA requirements). Both
the Pen dent and Upright Sprinklers
produce a hemispherical water distri­bution pattern below the deflector.

Intermediate Level Sprinklers are pri­marily designed for use in rack storage
sprinkler systems where their thermally
sensitive elements must be shielded
from the water spray of higher ele­vation sprinklers that could operate
earlier during a fire. Intermediate Level
Sprinklers are also used in other appli­cations such as beneath open gridded
catwalks.

NOTICE

The Series TY-L Sprinklers described
herein must be installed and main­tained in compliance with this docu­ment, as well as with the applicable
standards of the National Fire Protec­tion Association, in addition to the stan­dards of any other authorities hav ing
jurisdiction. Failure to do so may impair
the performance of these devices.

IMPORTANT

Refer to Technical Data Sheet
TFP2300 for warnings pertaining to
regulatory and health information.

Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal­lation of sprinkler systems and com­ponents. Improper handling and
installation can permanently damage
a sprinkler system or its compo­nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.

The owner is responsible for main­taining their fire protection system
and devices in proper operating con­dition. Contact the installing contrac­tor or product manufacturer with any
questions.

Sprinkler
Identification
Number (SIN)

TY3113 – Upright 5.6K, 1/2”NPT
TY3211 – Pendent 5.6K, 1/2”NPT
TY4113 – Upright 8.0K, 3/4”NPT
TY4211 – Pendent 8.0K, 3 /4”NPT

TY3113 is a redesignation for S1809
and G3253

TY3211 is a redesignation for S1801
and G3112

TY4113 is a redesignation for S1822
and G3153

TY4211 is a redesignation for S1811
and G3102

Technical
Data

Approvals

UL and C-UL Listed
FM Approved
(Refer to Table A for complete approval
information including corrosion resistant
status.)

Maximum Working Pressure

175 psi (12,1 bar)

Discharge Coefficient

K = 5.6 gpm/psi½ (80,6 lpm/bar½)
K = 8.0 gpm/psi½ (11 5, 2 l p m /ba r½)

Temperature Ratings

Refer to Table A

Finishes

Natural Brass

Physical Characteristics

Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brass

Sealing Button . . . . . . . . . . . Bronze w/ TEFLON

Ejection Spring . . . . . . . . . . . . . . Stainless Steel

Strut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . MONEL

Hook ..................... Bronze/MONEL

Deflector . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze

Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Brass

Fusible Element . . . . . . . . . . . . .Solder, Copper,

Stainless Steel

Page 1 of 4 AUGUST 2018 TFP350

TFP350

(68,3 mm)

(FIELD ASSEMBLED - SEE INSTALLATION SECTION)(FACTORY ASSEMBLED)

3" (76,2 mm) DIA,

(66,7 mm)

(FACTORY ASSEMBLED)

3" (76,2 mm) DIA,

(69,9 mm)

(FIELD ASSEMBLED - SEE INSTALLATION SECTION)

(68,3 mm)

Page 2 of 4

1/2" NPT

2-11/16"

7/16"

(11,1 mm)

NOMINAL

MAKE-IN

UPRIGHT PENDENT

FACTORY

ASSEMBLED

UPRIGHT

SHIELD

WRENCH
FLANGES

WRENCH

AREA

MODEL S5

PENDENT

SHIELD

WITH

O-RINGS

7/16"
(11,1 mm)
NOMINAL

MAKE-IN

FIGURE 1

STANDARD RESPONSE SERIES TY-L UPRIGHT ( TY3113) AND PENDENT (TY3211) SPRINKLERS

INTERMEDIATE LEVEL SPRINKLERS, 5.6 K-FACTOR, 1/2 INCH NPT

3/4" NPT

2-3/4"

1/2"

(12,7 mm)

NOMINAL

MAKE-IN

FACTORY

ASSEMBLED

UPRIGHT

SHIELD

WRENCH
FLANGES

MODEL S5

PENDENT

SHIELD

WITH

O-RINGS

1/2"
(12,7 mm)
NOMINAL

MAKE-IN

2-5/8"

2-11/16"

WRENCH

AREA

UPRIGHT PENDENT

FIGURE 2

STANDARD RESPONSE SERIES TY-L UPRIGHT ( TY4113) AND PENDENT (TY4211) SPRINKLERS

INTERMEDIATE LEVEL SPRINKLERS, 8.0 K-FACTOR, 3/4 INCH NPT

SPRINKLER FINISH

K = 5.6 UPRIGHT TY3113

K = 5.6 PENDENT TY3211

TEM P.

RATI NG

16 5°F (74° C ) UNPAINTED

280° F (138°C) BLUE

NOTES

1. Listed by Under write rs Lab orator y, Inc. (UL).

2. Listed by Unde rwriters L abora tory, Inc. for use in Ca nada (C-UL)

3. A pprove d by Factor y Mutual Research Corporation.

FRAME COLOR

CODE

NATURAL BRASS NATURAL BRASS

K = 8.0 UPRIGHT TY4113

K = 8.0 PENDENT TY4211

1, 2, 3212°F (100°C) WHITE

TABL E A

LABORATORY LISTINGS AND APPROVALS

TFP350

WRENCH

Page 3 of 4

Operation

A copper tube sealed by two stainless
steel balls holds a fusible alloy. When
the rated temperature is reached, the
alloy melts, the balls are forced toward
each other releasing the tension mech­anism, allowing the sprinkler to operate.

Design
Criteria

The Series TY-L Pendent and Upright
Intermediate Level Sprinklers are
intended for fire protection systems
designed in accordance with the stan­dard installation rules recognized by
the applicable Listing or Approval
agency (e.g., UL Listing is based on
the requirements of NFPA 13, and FM
Approval is based on the requirements
of FM Global’s Loss Prevention Data
Sheets).

Installation

The Series TY-L Sprinklers must
be installed in accordance with this
section.

NOTE: A leak-tight 1/2 in. NPT sprin­kler joint should be obtained by apply­ing a minimum-to-maximum torque of
7 to 14 lb-ft (9,5 to 19,0 N·m). A leak
tight 3/4 in. NPT sprinkler joint should
be obtained by applying a minimum­to-maximum torque of 10 to 20 lb-ft
(13,4 to 26,8 N·m). Higher levels of
torque may distort the sprinkler inlet
and cause leakage or impairment of
the sprinkler.

Upright Sprinklers

The Series TY-L Intermediate Level
Upright Sprinklers must be installed
in accordance with the following
instructions.

Step 1. With pipe thread sealant
applied to the pipe threads, hand
tighten the sprinkler into the sprinkler
fitting.

Step 2. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
9 Sprinkler Wrench (Ref. Figure 3). With
reference to Figure 1 or 2, the W-Type
9 Sprinkler Wrench is to be applied to
the wrenching area.

Pendent Sprinklers

The Series TY-L Intermediate Level
Pendent Sprinklers must be installed
in accordance with the following
in structions.

Step 1. Roll one of the two required
O-Rings over the sprinkler threads until
it seats against the sprinkler wrenching
area flange as shown in Figure 1 or 2,
as applicable.

Step 2. Install the Shield over the sprin­kler threads, and then roll the second
O-Ring over the sprinkler threads until
it is seated firmly against the Shield.

Step 3. With pipe thread sealant
ap plied, hand tighten the sprinkler into
the sprinkler fitting.

Step 4. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
9 Sprinkler Wrench (Ref. Figure 3). The
wrench is to be applied to the sprinkler
wrenching area shown in Figure 1 or 2,
as applicable.

When installed correctly, the O-Rings
will be slightly compressed and the
Shield will be held firmly in place.

RECESS

FIGURE 3

W-TYPE 9 SPRINKLER

WRENCH

Care and
Maintenance

The Series TY-L Sprinklers must be
maintained and serviced in accordance
with this section.

Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shut down the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.

Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.

Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi­fied or over-heated sprinklers must be
replaced.

Care must be exercised to avoid
damage to the sprinklers before,
during, and after installation. Sprin­klers damaged by dropping, striking,
wrench twist/slippage, or the like, must
be replaced.

The owner is responsible for the
inspection, testing, and maintenance of
their fire protection system and devices
in compliance with this document, as
well as with the applicable standards
of the National Fire Protection Asso­ciation (e.g., NFPA 25), in addition to
the standards of any other authorities
having jurisdiction. Contact the install­ing contractor or product manufacturer
with any questions.

It is recommended that automatic
sprinkler systems be inspected, tested,
and maintained by a qualified Inspec­tion Service in accordance with local
requirements and/or national codes.

TFP350

Page 4 of 4

P/N 53 — XXX — X — XXX

SIN

253 5.6K UPRIGHT (1/2 in. NPT) T Y311 3

153 8.0K UPRIGHT (3/4 in. NPT) T Y4113

PART NUMBER SELECTION

SERIES TY-L UPRIGHT INTERMEDIATE LEVEL SPRINKLERS

(UPRIGHT SHIELD INCLUDED WITH SPRINKLER)

P/N 51 — XXX — X — XXX

SIN

112 5.6K PENDENT (1/2 in. NPT) T Y3211

102 8.0K PENDENT (3/4 in. NPT) T Y42 11

PART NUMBER SELECTION

SERIES TY-L PENDENT SPRINKLERS

(MODEL S5 PENDENT SHIELD & O-RING MUST BE SEPARATELY ORDERED)

1 NATURAL BRASS

TABL E B

1 NATURAL BRASS

TABL E C

SPRINKLER

SPRINKLER

TEMPERATURE

RATI NG

165 16 5°F (74° C )

212 212°F (100°C)

280 280° F (138°C)

TEMPERATURE

RATI NG

165 16 5°F (74° C )

212 212°F (100°C)

280 280° F (138°C)

Limited
Warranty

For warranty terms and conditions, visit
www.tyco-fire.com.

Ordering
Procedure

Contact your local distributor for avail­ability. When placing an order, indicate
the full product name and Part Number
(P/N).

Upright Sprinkler Assemblies
with Shield and NPT Thread
Connections

Specify: (Specify Model/SIN), Stan­dard Response, (specify K-factor),
(specify temperature rating), Series
TY-L Upright Intermediate Level Sprin­klers with natural brass finish, P/N
(specify from Table B)

Pendent Sprinkler Assemblies with
(Shield Ordered Separately) and
NPT Thread Connections

Specify: (Specify Model/SIN), Stan­dard Response, (specify K-factor),
(specify temperature rating), Series
TY-L Pendent Sprinkler with natural
brass finish, P/N (specify from Table C)

Model S5 Pendent Shield Package

Specify: S5 Pendent Shield Package
(one shield / two O-Rings) for use with
(specify 1/2 in. NPT or 3/4 in. NPT)
Series TY-L Pendent Sprinklers, P/N
(specify)

1/2 in. NPT ...................56-015-6-802

3/4 in. NPT ...................56-015-6-803

Sprinkler Wrench

Specify: W-Type 9 Sprinkler Wrench,
P/N 56-000-1-849

1400 Pennbr ook Par kway, L ansd ale, PA 19446 | Tele phon e [phone]

© 2018 John son Control s. All right s reserved. A ll specifica tions and ot her informa tion shown wer e current as o f document rev ision date an d are subject t o change wit hout notice.

NATIONAL FIRE P ROTECTION ASSOCIATIO N and NFPA are register ed trademarks of N ational Fire Protec tion Associati on;
MONEL is a reg istered tradema rk of Special Met als Corporatio n;
TEFLON is a regi stered tradema rk of DuPont