Tyco Illustra Essentials 1MP, Illustra Essentials 2MP Quick Start Manual

Illustra Essentials

Indoor / Outdoor HD Bullet

Quick Start Guide

8200-1102-01 B0

i

Notice

Please read this manual thoroughly and save it for future use before attempting to connect or operate this unit.

The information in this manual was current when published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to change without notice.

Copyright

Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or
reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of
Tyco Security Products. © 2014 Tyco Security Products. All rights reserved.

Customer Service

Thank you for using Tyco Security Products. We support our products through an extensive worldwide network
of dealers. The dealer through whom you originally purchased this product is your point of contact if you need
service or support. Our dealers are empowered to provide the very best in customer service and support.
Dealers should contact Tyco Security Products at [phone] or [phone] or on the Web at

www.illustraessentials.com.

Trademarks

The trademarks, logos, and service marks displayed on this document are registered in the United States [or
other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security Products. will
aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal
prosecution wherever necessary. All trademarks not owned by Tyco Security Products. are the property of their
respective owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from
photos. Not all products include all features. Availability varies by region; contact your sales representative.

ii

Important Safeguards and Warnings

1．Electrical safety

All installation and operation should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may result in

device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or

installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability of

the camera.

iii

6. Daily Maintenance

Accessory Name

Amount

Network Camera Unit

1

Quick Start Guide

1

Installation Accessories Bag

1

CD

1

Please shut down the device and then unplug the power cable before you begin daily maintenance work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute

the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the device

or clean the enclosure when you are doing maintenance work. Please use professional optical clean
method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result in poor
IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

iv

Table of Contents

Important Safeguards and Warnings .................................................................................................................. ii

Table of Contents .............................................................................................................................................. iv

Framework ......................................................................................................................................................... 1

Cable ......................................................................................................................................................... 1

Framework and Dimension ....................................................................................................................... 2

Device Installation .............................................................................................................................................. 4

Quick Configuration Tool ................................................................................................................................... 6

Overview ................................................................................................................................................... 6

Operation .................................................................................................................................................. 6

Web Operation ................................................................................................................................................... 8

Network Connection .................................................................................................................................. 8

Login and Main Interface .......................................................................................................................... 8

Appendix Toxic or Hazardous Materials or Elements .................................................................................... 10