TYAN Triumph i7520 (S6623, Triumph i7520, S6623 User Manual
http://www.tyan.com
1
Triumph i7520
///
S6623
Version 1.0
Copyright
Copyright © TYAN Computer Corporation, 2006. All rights reserved. No part of
this manual may be reproduced or translated without prior written consent from
TYAN Computer Corp.
Trademark
All registered and unregistered trademarks and company names contained in
this manual are property of their respective owners including, but not limited to
the following.
TYAN, Taro and Triumph i7520 are trademarks of TYAN Computer Corporation.
Intel, Xeon, and combinations thereof are trademarks of Intel Corporation.
ATI is a trademark of ATI Technologies Inc.
Phoenix, Phoenix-Award BIOS are trademarks of Phoenix Technologies.
Microsoft, Windows are trademarks of Microsoft Corporation.
SuSE,is a trademark of SuSE AG.
Linux is a trademark of Linus Torvalds
IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.
Winbond is a trademark of Winbond Electronics Corporation.
Notice
Information contained in this document is furnished by TYAN Computer
Corporation and has been reviewed for accuracy and reliability prior to printing.
TYAN assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN products including liability or
warranties relating to fitness for a particular purpose or merchantability. TYAN
retains the right to make changes to product descriptions and/or specifications
at any time, without notice. In no event will TYAN be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.
http://www.tyan.com
2
Table of Contents
Chapter 1: Introduction
1.1 Congratulations Page 5
1.2 Hardware Specifications Page 5
Chapter 2: Board Installation
2.1 Board Image Page 8
2.2 Block Diagram Page 10
2.3 Board Parts, Jumpers and Connectors Page 12
2.4 Mounting the Motherboard Page 25
2.5 Installing the Memory Page 26
2.6 Installing the Processor and Cooling Fan Page 29
2.7 Attaching Drive Cables Page 31
2.8 Installing Add-In Cards Page 33
2.9 Installing Optional SO-DIMM Modules Page 34
2.10 Connecting External Devices Page 35
2.11 Installing the Power Supply Page 36
2.12 Finishing Up Page 37
Chapter 3: BIOS
3.1 Main Menu Page 40
3.2 Advanced Menu Page 43
3.3 Security Menu Page 58
3.4 PC Health Menu Page 59
3.5 Clk/Misc. Menu Page 61
3.6 Exit Menu Page 62
Chapter 4: Diagnostics
4.1 Beep Codes Page 63
4.2 Flash Utility Page 63
4.3 AWARD BIOS Post Code Page 64
Appendix I: How to Make a Driver Diskette
Page 69
Glossary
Page 71
Technical Support
Page 77
http://www.tyan.com
3
Check the box contents!
The retail motherboard package should contain the following:
1 x Triumph i7520 S6623 motherboard
1 x VGA cable
1 x COM Port Cable
1 x PS/2 Cable
1 x TYAN driver CD
1 x Serial ATA cable
If any of these items are missing, please contact your vendor/dealer for
replacement before continuing with the installation process.
http://www.tyan.com
4
NOTE
http://www.tyan.com
5
Chapter 1: Introduction
1.1 - Congratulations
Congratulations on your purchase of the powerful Dual Intel processor solution,
the Triumph i7520 S6623. Based on Intel E7520 chipset, the S6623 offers
exceptional performance. Compatible with EPS12V power supplies, the EEB
3.51 form factor S6623 features an onboard ATI ES1000 PCI graphics
controller with 16 MB memory, four Intel 82571EB dual port Gigabit controllers
and 2 SATA ports from ICH5R, which provides a versatile solution for your
server needs.
Remember to visit TYAN’s Website at http://www.tyan.com. There you can find
information on all of TYAN’s products with FAQ’s, online manuals and BIOS
upgrades.
1.2 - Hardware Specifications
Processors
• Two 604-pin sockets support Intel
CPUs of the same type below:
? Xeon Dual Core (Paxville CPU) with
2x2MB L2
? Xeon (Nadona, 1M L2), up to
3.6GHz
? Xeon (Irwindale, 2M L2), up to
3.6GHz
? Xeon LV (Low Voltage) CPU, up to
2.8GHz
• Separated 4-phase VRD for each
CPU
Memory
• Four 240-pin DDR2 sockets support
up to 8GB
• Dual channel memory bus (must be
populated in pairs)
• Registered DDR2 400 compliant ECC
DIMM
• Supports 256MB, 512MB, 1GB and
2GB DIMM
Chipset
• Intel E7520 Memory Controller Hub
LAN Bypass
• Supports Bypass feature over one
pair of LAN ports (LAN 1 & 2)
Front Panel I/O Ports
• One serial port with D-Sub
connector
• Two USB ports with Dual-Stack
USB connector
• 8 RJ45 Connectors (S6623P8B)
• Four of eight LAN ports could be
configured to Optical SFP
connectors (refer to Available
Models)
System Management
• Total 5 fan headers with control
and tachometer monitoring
• Monitors voltage for CPU,
Memory & Power Supply
• Monitors temperature for CPU &
environment
• Onboard LED: LAN bypass, Fault
FED Pin Header: Power LED &
HDD LED
• One pin header for Chassis
http://www.tyan.com
6
• Intel 82801ER I/O Controller Hub
(ICH5R)
• Intel 6700PXH PCI/PCI-X Controller
Hub
Integrated LAN Controllers
• Four Intel 82571EB dual port Gagabit
Controllers
• Configurable with total 8 Gigabit LAN
ports, Max. 4 of 8 ports could be over
Fiber connectors (refer to Available
Models)
Integrated 2D/3D Graphics
• Onboard ATI ES1000 PCI graphics
controller with 16MB memory
Expansion Slots
• One 64-bit 133MHz PCI-X slot
(3.3V) (M2052-RS)
• One Taro slot supports Tyan M6120
CN-1120 card
Integrated SATA Controller
• 2 SATA ports from ICH5R
• RAID 0, 1 supported
Form Factor
• EEB 3.51 form factor (12” x 13”, 305
x 330mm)
Power Supply
• EPS 12V Power Supply (24-pin, 8-pin
power connectors)
Intrusion detection
• Supports Serial Console Redirect
• Optional SRAM to restore
customized private keys
• Supports Watch Dog Timer
BIOS
• AWARD BIOS® on 4Mbit Flash
ROM
• Supports ACPI 2.0
• Supports boot from USB device
• Power-on mode control for AC
power loss recovery
M6120 Networking Security addon card (optional)
• Cavium CN-1120-X Security
Macro Processor add-on card
supports IPsec/SSL
Integrated I/O
• One 40-pin IDE connector
• One 50-pin Compact Flash Type
II connector
• Two SATA connectors
• One pin header for USB ports
(supports two USB 2.0 devices)
• One shrouded header for serial
port
• One shrouded header for parallel
port
• One pin header for PS/2 mouse
and keyboard
• One pin header for VGA port
• One pin header for SMBUS
connection
Available Models
Model GbE over Fiber GbE over Copper LAN Bypass Remarks
S6623T4P4 4 ports 4 ports N/A Standard
S6623P8B N/A 8 ports Yes standard
S6623T2P6 2 ports 6 ports N/A
S6623T4P2 4 ports 2 ports N/A
http://www.tyan.com
7
Chapter 2: Board Installation
Precautions: The Triumph i7520 supports SSI, EPS12V type power supplies
(24pin + 8pin) and will not operate with any other types. For proper power
supply installation procedures see page 37.
DO NOT USE ATX 2.x or ATXGES power supplies as they will damage the
board and void your warranty.
How to install our products right… the first time
The first thing you should do is reading this user’s manual. It contains important
information that will make configuration and setup much easier. Here are some
precautions you should take when installing your motherboard:
(1) Ground yourself properly before removing your motherboard from the
antistatic bag. Unplug the power from your computer power supply and
then touch a safely grounded object to release static charge (i.e. power
supply case). For the safest conditions, TYAN recommends wearing a
static safety wrist strap.
(2) Hold the motherboard by its edges and do not touch the bottom of the
board, or flex the board in any way.
(3) Avoid touching the motherboard components, IC chips, connectors,
memory modules, and leads.
(4) Place the motherboard on a grounded antistatic surface or on the
antistatic bag that the board was shipped in.
(5) Inspect the board for damage.
The following pages include details on how to install your motherboard into your
chassis, as well as installing the processor, memory, disk drives and cables.
NOTE
DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN
DAMAGED.
http://www.tyan.com
8
2.1- Board Image
This picture is representative of the latest board revision available at
the time of publishing. The board you receive may or may not look
exactly like the above picture.
Triumph i7520 (S6623P8B)
http://www.tyan.com
9
Triumph i7520 (S6623T4P4)
http://www.tyan.com
10
2.2 - Block Diagram
Triumph i7520 (S6623P8B) block diagram
http://www.tyan.com
11
Triumph i7520 (S6623T4P4) block diagram
http://www.tyan.com
12
2.3 - Board Parts, Jumpers and Connectors
Triumph i7520 (S6623P8B)
http://www.tyan.com
13
Triumph i7520 (S6623T4P4)
This diagram is representative of the latest board revision available at the time of
publishing. The board you receive may not look exactly like the above diagram.
Jumper Legend
©©
OPEN - Jumper OFF, without jumper cover
©©
CLOSED – Jumper ON, with jumper cover
http://www.tyan.com
14
Jumper/Connector Function
FAN1/2/3/4/5 Fan Connector
VGA1 Pin Header for VGA Port
COM2 Box Header for COM Port
LPT1 Box Header for LPT Port
LPC1 Pin Header for LPC Ports
CF1 Compact Flash Connector
J8 200-pin SO-DIMM Socket
KM1 Pin Header for Keyboard & Mouse
SW1 System RESET Switch
SW2 System Power-ON Switch
FP-USB1 Pin Header for Internal USB Ports
FPIO1 Front Panel Connector
IDE1 IDE Connector
Red LED: shows fan/voltage/temperature fault
status
LED14
Green LED: shows LAN1/LAN2 LAN Bypass status
(for S6623P8B only)
SATA1/SATA2 Serial ATA Connector
JP2 Pin Header for Disk on Module Power Pin
CCMOS1 Clear CMOS Jumper
http://www.tyan.com
15
COM2
LPT1
FP-
USB1
http://www.tyan.com
16
FP-USB1: Pin Header for Internal USB Ports
10 2
9 1
Signal Pin Pin Signal
VCC 1 2 VCC
-Data 0
3 4 - Data 1
+ Data 0 5 6 + Data 1
GND 7 8 GND
KEY 9 10
NC
COM2: Box Header for COM Port
1029
1
Use these pin definitions to connect a port to COM2.
Signal Pin Pin Signal
DCD 1 2 DSR
RXD 3 4 RTS
TXD 5 6 CTS
DTR 7 8 RI
GND 9 10
KEY
LPT1: Box Header for LPT Port
1
25
26
2
Signal Pin Pin Signal
STB#
1 2 AFD#
PD0 3 4 ERR#
PD1 5 6 INIT#
PD2 7 8 SLIN#
PD3 9 10
GND
PD4 11 12
GND
PD5 13 14
GND
PD6 15 16
GND
PD7 17 18
GND
ACK# 19 20
GND
BUSY 21 22
GND
PE 23 24
GND
SLCT 25
http://www.tyan.com
17
SW2
FPIO1
FAN1
FAN2
FAN5
FAN4
FAN3
http://www.tyan.com
18
FAN1/FAN2/FAN3/FAN4/FAN5: Fan Connector with Speed Control
+12V
GND
TACH
1
+12V
NC
GND
TACH
1
Use these headers to connect the cooling fans to
the motherboard to monitor their fan speeds to
keep the system stable and reliable.
FPIO1: Front Panel Header
The motherboard provides one front panel header for electrical connection to
the front panel switches and LED’s.
Power_LED+
Power_LED-
PWR_ON+
GND
Warning LED+
Warning LED-
_
GND
INTRU-
2
4
6
8
10
12
14
16
18
1
3
5
7
9
11
13
15
17
HDD_LED+
HDD_LED-
GND
RST_SW+
VCC
Ext. Interrupt
5VSB
SMBUS Data
SMBUS Clock
SW2: System POWER-ON Switch
Pin 1 Pin 2 Pin 3 Pin 4
PWRSW-
PWRSW-
GND GND
http://www.tyan.com
19
J8 SW1
VGA1
KM1
http://www.tyan.com
20
VGA1: Pin Header for VGA Port
15116
2
Signal Pin Pin
Signal
Red 1 2 Green
Blue 3 4 NC
GND 5 6 GND
GND 7 8 GND
VCC 9 10
GND
NC 11 12 DDC Data
H. SYNC 13 14 v. SYNC
DDC Clock 15 16
KEY
KM1: Pin Header for Keyboard and Mouse
10 2
9 1
Signal Pin Pin
Signal
VCC 1 2 VCC
KEY 3 4 KEY
KB Data 5 6 Mouse Data
GND 7 8 GND
KB CLK 9 10 Mouse CLK
J8: SO-DIMM Socket
Supports TYAN M6120 CN-1120 card.
SW1: System RESET Switch
Pin 1 Pin 2 Pin 3 Pin 4
RSTSW- RSTSW- GND GND
http://www.tyan.com
21
CF1
LPC1
http://www.tyan.com
22
CF1: Compact Flash Connector
Pin Signal Pin Signal
1 GND 26 GND
2 D3 27 D11
3 D4 28 D12
4 D5 29 D13
5 D6 30 D14
6 D7 31 D15
7 CS# 32 CS1#
8 GND 33 GND
9 GND 34 IORD#
10 GND 35 IOWR#
11 GND 36 VCC
12 GND 37 INTRQ
13 VCC 38 VCC
14 GND 39 GND
15 GND 40 NC
16 GND 41 RST#
17 GND 42 IORDY#
18 A2 43 DMARQ
19 A1 44 DMACK#
20 A0 45 DASP#
21 D0 46 PDIAG#
22 D1 47 D8
23 D2 48 D9
24 NC 49 D10
25 GND 50 GND
LPC1: Pin Header for LPC Ports
192
10
Signal Pin Pin
Signal
+3.3V
1 2 LFRAME#
LAD0
3 4 X
LAD1
5 6 PCI_RESET#
LAD2
7 8 GND
LAD3
9 10 PCI_CLOCK
1
2
26
27
50
25
http://www.tyan.com
23
JP2
CCMOS1
LED14
http://www.tyan.com
24
CCMOS1: Clear CMOS Jumper
JP2: Pin Header for Disk on Module Power Pin
LED14: System Status Indicator
3
1
Normal
(default)
1
3
Clear CMOS
Use this jumper when you forgot your system/setup
password or need to clear system BIOS setting.
How to clear the CMOS data
- Power off system and disconnect power supply
from AC source
- Use jumper cap to close Pin_2 and 3 for several
seconds to Clear CMOS
- Replace jumper cap to close Pin_1 and 2
Reconnect power supply to AC source
Power on system
1
3
Normal
(default)
IDE1 Pin20=Normal (default)
3
1
IDE1 Pin20=+5V (for disk on module VCC Power)
Red LED On: fan, voltage or temperature fail
Red LED Off: fan, voltage or temperature work normal
Green LED On: LAN1/LAN2 in LAN Bypass Mode
(S6623P8B only)
Green LED Off: LAN1/LAN2 in Normal Mode
(S6623P8B only)
Loading...