TYAN GT24-B8236-IL Service Engineer's Manual
GT24-B8236-IL
Service Engineer’s Manual
2
http://www.tyan.com
3
http://www.tyan.com
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any material contained herein, may be reproduced
without written consent of manufacturer.
Copyright 2011 MiTAC International Corporation. All rights reserved. TYAN® is
a registered trademark of MiTAC International Corporation.
Version 1.1
Disclaimer
Information contained in this document is furnished by MiTAC International
Corporation and has been reviewed for accuracy and reliability prior to printing.
MiTAC assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN
®
products including liability or
warranties relating to fitness for a particular purpose or merchantability. MiTAC
retains the right to make changes to produce descriptions and/or specifications
at any time, without notice. In no event will MiTAC be held liable for any direct
or indirect, incidental or consequential damage, loss of use, loss of data or
other malady resulting from errors or inaccuracies of information contained in
this document.
Trademark Recognition
All registered and unregistered trademarks and company names contained in
this manual are property of their respective owners including, but not limited to
the following.
TYAN
®
is a trademark of MiTAC International Corporation.
Intel
®
is a trademark of Intel® Corporation.
AMD
®
is a trademark of AMD® Corporation.
AMI
®
, AMIBIOS® and combinations thereof are trademarks of AMI
Technologies.
Microsoft®, Windows® are trademarks of Microsoft Corporation.
IBM
®
, PC®, AT® and PS/2® are trademarks of IBM Corporation.
Winbond
®
is a trademark of Winbond Electronics Corporation.
4
http://www.tyan.com
FCC Declaration
Notice for the USA
Compliance Information Statement (Declaration of
Conformity Procedure) DoC FCC Part 15: This
device complies with part 15 of the FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following conditions:
This device must not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003. Cet
appareil numérique de la Classe A est conforme à la norme NMB-003 du
Canada.
Notice for Europe (CE Mark)
This product is in conformity with the Council
Directive 2004/108/EC.
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. There will be danger of explosion if
battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery according to
manufacturer instructions and in accordance with your local regulations.
5
http://www.tyan.com
About this Manual
This manual provides you with instructions on installing your TYAN
GT24-B8236-IL. This Manual is intended for experienced users and
integrators with hardware knowledge of personal computers.
This manual consists of the following parts:
1. Chapter1: Product Introduction
Provides an introduction to the TYAN GT24-B8236-IL barebones,
standard parts list, describes the external components, gives a table
of key components, and provides block diagram of the system.
2. Chapter2: Hardware Setup
Covers procedures on installing the CPU, memory modules and
hard drives.
3. Chapter3: Installation Options
Covers removal and replacement procedures for pre-installed compo
n
4. Appendix:
List the cable connection and FRU part tables for reference of
system setup, and technical support in case a problem arises with
your system.
6
http://www.tyan.com
Safety and Compliance Information
Before installing and using TYAN GT24-B8236-IL, take note of the following
precautions:
·Read all instructions carefully.
·Do not place the unit on an unstable surface, cart, or stand.
·Do not block the slots and opening on the unit, which are provided for
ventilation.
· Only use the power source indicated on the marking label. If you are not
sure, contact the power company.
·The unit uses a three-wire ground cable, which is equipped with a third pin to
ground the unit and prevent electric shock. Do not defeat the purpose of this
pin. If your outlet does not support this kind of plug, contact your electrician
to replace your obsolete outlet.
·Do not place anything on the power cord. Place the power cord where it will
not be in the way of foot traffic.
·Follow all warnings and cautions in this manual and on the unit case.
·Do not push objects in the ventilation slots as they may touch high voltage
components and result in shock and damage to the components.
· When replacing parts, ensure that you use parts specified by the
manufacturer.
·When service or repairs have been done, perform routine safety checks
to verify that the system is operating correctly.
·Avoid using the system near water, in direct sunlight, or near a heating
device.
·Cover the unit when not in use.
7
http://www.tyan.com
Safety Information
Retain and follow all product safety and operating instructions provided
with your equipment. In the event of a conflict between the instructions in
this guide and the instructions in equipment documentation, follow the
guidelines in the equipment documentation.
Observe all warnings on the product and in the operating instructions. To
reduce the risk of bodily injury, electric shock, fire and damage to the
equipment, observe all precautions included in this guide.
You must become familiar with the safety information in this guide before
you install, operate, or service TYAN products.
Symbols on Equipment
Caution. This symbol indicates a potential
hazard. The potential for injury exists if
cautions are not observed. Consult equipment
documentation for specific details.
Warning. This symbol indicates the presence
of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified
personnel.
Warning. This symbol indicates the presence of a
hot surface or hot component. If this surface is
contacted, the potential for injury exists.
To reduce risk of injury from a hot component,
allow the surface to cool before touching.
General Precautions
· Follow all caution and warning instructions marked on the equipment and
explained in the accompanying equipment documentation.
Machine Room Environment
· Make sure that the area in which you install the system is properly
ventilated and climate-controlled.
8
http://www.tyan.com
· Ensure that the voltage and frequency of your power source match the
voltage and frequency inscribed on the electrical rating label of the
equipment.
· Do not install the system in or near a plenum, air duct, radiator, or heat
register.
· Never use the product in a wet location.
Equipment Chassis
· Do not block or cover the openings to the system.
· Never push objects of any kind through openings in the equipment.
Dangerous voltages might be present.
· Conductive foreign objects can produce a short circuit and cause fire,
electric shock, or damage to your equipment.
· Lift equipment using both hands and with your knees bent.
Equipment Racks
To avoid injury or damage to the equipment:
· Observe local occupational health and safety requirements and guidelines
for manual materials handling.
· Do not attempt to move a rack by yourself; a minimum of two people are
needed to move a rack.
· Do not attempt to move a fully loaded rack. Remove equipment from the
rack before moving it.
· Do not attempt to move a rack on an incline that is greater than 10 degrees
from the horizontal.
· Make sure the rack is properly secured to the floor or ceiling.
· Make sure the stabilizing feet are attached to the rack if it is a single-rack
installation.
· Make sure racks are coupled together if it is a multiple-rack installation.
· Make sure the rack is level and stable before installing an appliance in the
rack.
· Make sure the leveling jacks are extended to the floor.
9
http://www.tyan.com
· Make sure the full weight of the rack rests on the leveling jacks.
· Always load the rack from the bottom up. Load the heaviest component in
the rack first.
· Make sure the rack is level and stable before pulling a component out of the
rack.
· Make sure only one component is extended at a time. A rack might become
unstable if more than one component is extended.
To avoid damage to the equipment:
· The rack width and depth must allow for proper serviceability and cable
management.
· Ensure that there is adequate airflow in the rack. Improper installation or
restricted airflow can damage the equipment.
· The rack cannot have solid or restricted airflow doors. You must use a
mesh door on the front and back of the rack or remove the doors to ensure
adequate air flow to the system.
· If you install the Model in a rack, do not place equipment on top of the unit.
It will cause restricted airflow and might cause damage to the equipment.
·
Make sure the product is properly matted with the rails. Products that are
improperly matted with the rails might be unstable.
·
Verify that the AC power supply branch circuit that provides power to the
rack is not overloaded. This will reduce the risk of personal injury, fire, or
damage to the equipment. The total rack load should not exceed 80 percent
of the branch circuit rating. Consult the electrical authority having jurisdiction
over your facility wiring and installation requirements.
Equipment Power Cords
· Use only the power cords and power supply units provided with your
system. The system might have one or more power cords.
· Plug the power cord into a grounded (earthed) electrical outlet that is easily
accessible at all times.
· In all European electrical environments, you must ground the Green/Yellow
tab on the power cord. If you do not ground the Green/Yellow tab, it can
cause an electrical shock due to high leakage currents.
10
http://www.tyan.com
·
Do not place objects on AC power cords or cables. Arrange them so that no
one might accidentally step on or trip over them.
· Do not pull on a cord or cable. When unplugging from the electrical outlet,
grasp the cord by the plug.
· To reduce the risk of electrical shock, disconnect all power cords before
servicing the appliance.
Equipment Batteries
· The system battery contains lithium manganese dioxide. If the battery pack
is not handled properly, there is risk of fire and burns.
· Do not disassemble, crush, puncture, short external contacts, or dispose of
the battery in fire or water.
· Do not expose the battery to temperatures higher than 60°C (140°F).
· The system battery is not replaceable. If the battery is replaced by an
incorrect type, there is danger of explosion. Replace the battery only with a
spare designated for your product.
· Do not attempt to recharge the battery.
· Dispose of used batteries according to the instructions of the manufacturer.
Do not dispose of batteries with the general household waste. To forward
them to recycling or proper disposal, use the public collection system or return
them to TYAN, your authorized TYAN partner, or their agents.
Equipment Modifications
· Do not make mechanical modifications to the system. TYAN is not
responsible for the regulatory compliance of TYAN equipment that has been
modified.
Equipment Repairs and Servicing
· The installation of internal options and routine maintenance and service of
this product should be performed by individuals who are knowledgeable about
the procedures, precautions, and hazards associated with equipment
containing hazardous energy levels.
· Do not exceed the level of repair specified in the procedures in the product
documentation. Improper repairs can create a safety hazard.
11
http://www.tyan.com
· Allow the product to cool before removing covers and touching internal
components.
· Remove all watches, rings, or loose jewelry when working before removing
covers and touching internal components.
· Do not use conductive tools that could bridge live parts.
· Use gloves when you remove or replace system components; they can
become hot to the touch.
· If the product sustains damage requiring service, disconnect the product
from the AC electrical outlet and refer servicing to an authorized service
provider. Examples of damage requiring service include:
– The power cord, extension cord, or plug has been damaged.
– Liquid has been spilled on the product or an object has fallen into the
product.
– The product has been exposed to rain or water.
– The product has been dropped or damaged.
– The product does not operate normally when you follow the operating
instructions.
12
http://www.tyan.com
13
http://www.tyan.com
Table of Contents
Chapter 1: Overview....................................................................... 15
1.1 About the TYAN GT24-B8236-IL............................................ 15
1.2 Product Model ........................................................................ 15
1.3 Features ................................................................................. 16
1.4 Standard Parts List................................................................. 22
1.4.1 Box Contents ................................................................... 22
1.4.2 Accessories ..................................................................... 23
1.6 About the Product................................................................... 24
1.6.1 System Front View .......................................................... 24
1.6.2 System Rear View ........................................................... 25
1.6.3 LED Definitions................................................................ 26
1.6.4 Motherboard (S8236-IL) Layout ...................................... 28
1.6.5 Jumpers & Connectors .................................................... 29
1.6.6 System Block Diagram..................................................... 30
1.6.7 Internal View .................................................................... 31
Chapter 2: Setting Up..................................................................... 33
2.0.1 Before you Begin ............................................................. 33
2.0.2 Work Area........................................................................ 33
2.0.3 Tools ................................................................................ 33
2.0.4 Precautions...................................................................... 34
2.1 Installing Motherboard Components ...................................... 35
2.1.1 Removing the Chassis Cover.......................................... 35
2.1.2 Installing the CPU and Heatsink...................................... 36
2.1.3 Installing the Memory ...................................................... 39
2.1.4 Installing Hard Drives ...................................................... 44
2.1.5 Installing the PCI-E Cards ............................................... 46
2.2 Rack Mounting........................................................................ 50
2.2.1 Installing the Server in a Rack......................................... 50
2.2.2 Installing the inner Rails to the Chassis .......................... 51
2.2.3 Installing the Outer Rails to the Rack .............................. 51
2.2.4 Rack mounting the Server............................................... 52
Chapter 3: Replacing Pre-Installed Components ........................ 55
3.1 Introduction............................................................................. 55
3.2 Disassembly Flowchart........................................................... 55
3.3 Removing the Cover............................................................... 57
3.4 Replacing Motherboard Components..................................... 57
3.4.1 Replacing Expansion Card.............................................. 57
3.4.2 Disconnecting All Motherboard Cables ........................... 59
14
http://www.tyan.com
3.4.3 Removing the Motherboard............................................. 60
3.5 Replacing the Slim DVD-ROM (optional) ............................. 61
3.6 Replacing the LED Control Board ........................................ 63
3.6.1 M1008 LED Control Board Features ............................... 65
3.6.2 M1008 LED Control Board Connector Pin Definition ...... 65
3.7 Replacing the System Fan.................................................... 66
3.8 Replacing the M1235 HDD Backplane ................................. 69
3.8.1 M1235 HDD Backplane Features.................................... 71
3.8.2 M1235 Connector Pin Definitions.................................... 73
3.9 Replacing the Power Supply .................................................. 75
3.9.1 Replacing the M7016 Power Distribution Board.............. 79
3.9.2 M7016 Power Distribution Board Feature........................ 80
3.9.3 M7016 Power Distribution Board Pin Definitions ............ 80
3.10 Replacing the Redundant Power Supply.............................. 82
Appendix I: Cable Connection Tables.......................................... 85
Appendix II: FRU Parts Table ........................................................ 87
Appendix III: Technical Support ................................................... 89
http://www.tyan.com
15
Chapter 1: Overview
1.1 About the TYAN GT24-B8236-IL
Congratulations on your purchase of the TYAN
®
GT24-B8236-IL, a highly optimized
rack-mountable barebone system. The GT24-B8236-IL is designed to support both
dual AMD® 45nm 8-Core/12-Core Opteron 6100 Series and 32nm
8-Core/12-Core/16-Core Opteron 6200 Series Processors. Leveraging advanced
technology from AMD®, GT24 B8236-IL server system is capable of offering scalable
32 and 64-bit computing, high bandwidth memory design, and up to 256GB REG or
64GB UNB 800/1066/1333/1600/1866 MHz DDR3 ECC memory, providing a rich
feature set and incredible performance. and lightning-fast PCI-E bus implementation.
The GT24-B8236-IL not only empowers your company in nowadays IT demand but
also offers a smooth path for future application usage.
TYAN
®
also offers the GT24-B8236-IL in a version that can support up to to four
hot-swap hard drives. The GT24-B8236-IL uses TYAN
®
’s latest chassis, featuring a
robust structure and a solid mechanical enclosure. All of this provides GT24
-B8236-IL the power and flexibility to meet the needs of nowadays server
application.
1.2 Product Model
Model HDD Bays Power supply
B8236G24V4H-IL Hot-swap, 4 HDDs 500 Watts (110/220VAC) Single
B8236G24W4H-IL Hot-swap, 4 HDDs 500 Watts (110/220VAC) Single
B8236G24W4HR-IL Hot-swap, 4 HDDs
(1)+(1) 450 Watts
Redundant power
16
http://www.tyan.com
1.3 Features
TYAN GT24-B8236-IL (B8236G24W4H-IL)
Form Factor
1U Rackmount
Chassis Model
GT24
Dimension (D x W x
H)
25.4" x 17.2" x 1.72" (645 x 436 x 43.6mm)
Motherboard
S8236WGM3NR-IL
Board Dimension
EEB, 12"x13" (305x330mm)
System
Gross Weight
17 kg
Buttons
(1) RST / (1) NMI / (1) ID / (1) PWR w/ LED
LEDs
(1) ID / (1) Warning / (3) LAN / (1) Reserved
Front Panel
I/O Ports
(2) USB ports
Type / Q'ty
2.5" or 3.5" Hot-Swap / (4)
External Drive
Bay
Supported HDD
Interface
SATA-II 3.0Gb/s / SAS 6.0Gb/s
System Cooling
Configuration
FAN
(6) 4cm fans
Type
EPS1U
Efficiency
PFC / 80 plus silver
Input Range
Full-range AC(100-240V)
Frequency
60 Hertz
Power Supply
Output Watts
500 Watts
AMD 45nm 8-Core/12-Core Opteron 6100 Series Processors
(Magny-Cours)
Supported CPU
Series
AMD 32nm 8-Core/12-Core/16-Core Opteron 6200 Series Processors
(Interlagos)
Socket Type / Q'ty
G34 / (2)
Thermal Design
Power(TDP)
115W
Processor
System Bus
Up to 6.4 GT/s Hyper-Transport link support
Chipset
AMD SR5690 + SP5100
Chipset
Super I/O
Winbond W83627DHG-P
Supported DIMM
Qty
(16) DIMM slots
DIMM Type / Speed
U/RDDR3, LV and ULV DDR3, LRDIMM / 1866/ 1600/ 1333/ 1066/ 800
MHz
Capacity
Up to 256GB RDIMM/ 64GB UDIMM
Memory channel
4 Channels per CPU
Memory
Memory voltage
1.5V/ 1.35V/ 1.25V
PCI-E
(2) PCI-E Gen.2 x16 slots
Expansion Slots
Pre-install TYAN
Riser Card
M2091, PCI-E x16 1U riser card (left) / M2091-R, PCI-E x16 1U riser card
(right)
17
http://www.tyan.com
Max. HBA
Dimension (H x L)
(2) 111.15mm x 167.65mm (FH/HL)
Port Q'ty
(3)
LAN
Controller
Intel 82574L / Intel 82576EB
Connector type
D-Sub 15-pin
Resolution
Up to 1600x1200@60Hz
Graphic
Chipset
Aspeed AST2050
USB
(4) ports (2 at front, 2 at rear)
COM
(1) DB-9 COM port
VGA
(1) D-Sub 15-pin port
I/O Ports
RJ-45
(3) ports
Chipset
Winbond W83795G
Voltage
Monitors voltage for CPU, memory, chipset & power supply
Temperature
Monitors temperature for CPU & system environment
LED
Over temperature warning indicator / Fan & PSU fail LED indicator
System
Monitoring
Others
Chassis intrusion detection / Watchdog timer support
Onboard Chipset
Onboard Aspeed AST2050
AST2050 IPMI
Feature
IPMI 2.0 compliant baseboard management controller (BMC) / Supports
storage over IP and remote platform-flash / BIOS update
Server
Management
AST2050 iKVM
Feature
24-bit high quality video compression / Dual 10/100 Mb/s MAC interfaces
Brand / ROM size
AMI / 4MB
BIOS
Feature
Plug and Play (PnP) /PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE boot / ACPI 2.0
power management /Power on mode after power recovery /
User-configurable H/W monitoring / Auto-configurable of hard disk types
Operating System OS supported list
Please refer to our OS supported list.
FCC (DoC)
Class A
Regulation
CE (DoC)
Yes
Operating Temp.
10° C ~ 35° C (50° F~ 95° F)
Non-operating
Temp.
- 40° C ~ 70° C (-40° F ~ 158° F)
Operating
Environment
In/Non-operating
Humidity
90%, non-condensing at 35° C
RoHS
RoHS 6/6
Compliant
Yes
Barebone
(1) GT24B8236-IL Barebone
Manual
(1) MB User's manual + (1) BB User's manual
Installation CD
(1) TYAN installation CD
Heatsink / Cooler
(2) G34 CPU heatsinks
Rail kit
(1) CRAL-0031, sliding rail kit for KGT24/ KGT62
Mounting Ear
(1) mounting ear kit
Package Contains
Cable Power Cord
(1) CCBL-0310, US type power cord / (1) CCBL-0300, EU type power
cord
18
http://www.tyan.com
Optional
accessories
Peripheral
(1) CSTK-0080, Slim type DVD kit w/cables
TYAN GT24B8236-IL (B8236G24V4H-IL)
Form Factor
1U Rackmount
Chassis Model
GT24
Dimension (D x W x H)
25.4" x 17.2" x 1.72" (645 x 436 x 43.6mm)
Motherboard
S8236GM3NR-IL
Board Dimension
EEB, 12"x13" (305x330mm)
System
Gross Weight
17 kg
Buttons
(1) RST / (1) NMI / (1) ID / (1) PWR w/ LED
LEDs
(1) ID / (1) Warning / (3) LAN / (1) Reserved
Front Panel
I/O Ports
(2) USB ports
Type / Q'ty
2.5" or 3.5" Hot-Swap / (4)
External Drive
Bay
Supported HDD Interface
SATA-II 3.0Gb/s
System Cooling
Configuration
FAN
(6) 4cm fans
Type
EPS1U
Efficiency
PFC / 80 plus silver
Input Range
Full-range AC(100-240V)
Frequency
60 Hertz
Power Supply
Output Watts
500 Watts
AMD 45nm 8-Core/12-Core Opteron 6100 Series Processors
(Magny-Cours)
Supported CPU Series
AMD 32nm 8-Core/12-Core/16-Core Opteron 6200 Series
Processors (Interlagos)
Socket Type / Q'ty
G34 / (2)
Thermal Design Power(TDP)
115W
Processor
System Bus
Up to 6.4 GT/s Hyper-Transport link support
Chipset
AMD SR5690 + SP5100
Chipset
Super I/O
Winbond W83627DHG-P
Supported DIMM Qty
(16) DIMM slots
DIMM Type / Speed
U/RDDR3, LV and ULV DDR3, LRDIMM / 1866/ 1600/ 1333/
1066/ 800 MHz
Capacity
Up to 256GB RDIMM/ 64GB UDIMM
Memory channel
4 Channels per CPU
Memory
Memory voltage
1.5V/ 1.35V/ 1.25V
PCI-E
(2) PCI-E Gen.2 x16 slots
Pre-install TYAN Riser Card
M2091, PCI-E x16 1U riser card (left) / M2091-R, PCI-E x16
1U riser card (right)
Expansion Slots
Max. HBA Dimension (H x L)
(2) 111.15mm x 167.65mm (FH/HL)
Port Q'ty
(3)
LAN
Controller
Intel 82574L / Intel 82576EB
19
http://www.tyan.com
Connector type
D-Sub 15-pin
Resolution
Up to 1600x1200@60Hz
Graphic
Chipset
Aspeed AST2050
USB
(4) ports (2 at front, 2 at rear)
COM
(1) DB-9 COM port
VGA
(1) D-Sub 15-pin port
I/O Ports
RJ-45
(3) ports
Chipset
Winbond W83795G
Voltage
Monitors voltage for CPU, memory, chipset & power supply
Temperature
Monitors temperature for CPU & system environment
LED
Over temperature warning indicator / Fan & PSU fail LED
indicator
System
Monitoring
Others
Chassis intrusion detection / Watchdog timer support
Onboard Chipset
Onboard Aspeed AST2050
AST2050 IPMI Feature
IPMI 2.0 compliant baseboard management controller (BMC) /
Supports storage over IP and remote platform-flash / BIOS
update
Server
Management
AST2050 iKVM Feature
24-bit high quality video compression / Dual 10/100 Mb/s MAC
interfaces
Brand / ROM size
AMI / 4MB
BIOS
Feature
Plug and Play (PnP) /PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE boot /
ACPI 2.0 power management /Power on mode after power
recovery / User-configurable H/W monitoring /
Auto-configurable of hard disk types
Operating
System
OS supported list
Please refer to our OS supported list.
FCC (DoC)
Class A
Regulation
CE (DoC)
Yes
Operating Temp.
10° C ~ 35° C (50° F~ 95° F)
Non-operating Temp.
- 40° C ~ 70° C (-40° F ~ 158° F)
Operating
Environment
In/Non-operating Humidity
90%, non-condensing at 35° C
RoHS RoHS 6/6 Compliant
Yes
Barebone
(1) GT24B8236-IL Barebone
Manual
(1) MB User's manual + (1) BB User's manual
Installation CD
(1) TYAN installation CD
Heatsink / Cooler
(2) G34 CPU heatsinks
Rail kit
(1) CRAL-0031, sliding rail kit for KGT24/ KGT62
Mounting Ear
(1) mounting ear kit
Package
Contains
Cable
Power Cord
(1) CCBL-0310, US type power cord / (1) CCBL-0300, EU type
power
cord
Optional
accessories
Peripheral
(1) CSTK-0080, Slim type DVD kit w/cables
20
http://www.tyan.com
TYAN GT24B8236-IL (B8236G24W4HR-IL)
Form Factor
1U Rackmount
Gross Weight
17 kg
Chassis Model
GT24
Dimension (D x W x
H)
25.4" x 17.2" x 1.72" (645 x 436 x 43.6mm)
Motherboard
S8236WGM3NR-IL
System
Board Dimension
EEB, 12"x13" (305x330mm)
Buttons
(1) RST / (1) NMI / (1) ID / (1) PWR w/ LED
LEDs
(1) ID / (1) Warning / (3) LAN / (1) Reserved
Front Panel
I/O Ports
(2) USB ports
Type / Q'ty
2.5" or 3.5" Hot-Swap / (4)
External Drive
Bay
Supported HDD
Interface
SATA-II 3.0Gb/s / SAS 6.0Gb/s
System Cooling
Configuration
FAN
(6) 4cm fans
Type
ERP1U
Efficiency
PFC / 80 plus silver
Redundancy
1+1
Input Range
Full-range AC(100-240V)
Frequency
60 Hertz
Power Supply
Output Watts
450 Watts
AMD 45nm 8-Core/12-Core Opteron 6100 Series Processors
(Magny-Cours)
Supported CPU
Series
AMD 32nm 8-Core/12-Core/16-Core Opteron 6200 Series Processors
(Interlagos)
Socket Type / Q'ty
G34 / (2)
Thermal Design
Power(TDP)
115W
Processor
System Bus
Up to 6.4 GT/s Hyper-Transport link support
Chipset
AMD SR5690 + SP5100
Chipset
Super I/O
Winbond W83627DHG-P
Supported DIMM
Qty
(16) DIMM slots
DIMM Type / Speed
U/RDDR3, LV and ULV DDR3, LRDIMM modules / Design spec compliant
with 1866/ 1600/ 1333/ 1066/ 800 MHz
Capacity
Up to 256GB RDIMM/ 64GB UDIMM
Memory channel
4 Channels per CPU
Memory
Memory voltage
1.5V/ 1.35V/ 1.25V
PCI-E
(2) PCI-E Gen.2 x16 slots
Max. HBA
Dimension (H x L)
(2) 111.15mm x 167.65mm (FH/HL)
Expansion Slots
Pre-install TYAN
Riser Card
M2091, PCI-E x16 1U riser card (left) / M2091-R, PCI-E x16 1U riser card
(right)
Port Q'ty
(3)
LAN
Controller
Intel 82574L / Intel 82576EB
Connector type
D-Sub 15-pin
Graphic
Resolution
Up to 1600x1200@60Hz
21
http://www.tyan.com
Chipset
Aspeed AST2050
USB
(4) ports (2 at front, 2 at rear)
COM
(1) DB-9 COM port
VGA
(1) D-Sub 15-pin port
I/O Ports
RJ-45
(3) ports
Chipset
Winbond W83795G
Voltage
Monitors voltage for CPU, memory, chipset & power supply
Temperature
Monitors temperature for CPU & system environment
LED
Over temperature warning indicator / Fan & PSU fail LED indicator
System
Monitoring
Others
Chassis intrusion detection / Watchdog timer support
Onboard Chipset
Onboard Aspeed AST2050
AST2050 IPMI
Feature
IPMI 2.0 compliant baseboard management controller (BMC) / Supports
storage over IP and remote platform-flash / BIOS update
Server
Management
AST2050 iKVM
Feature
24-bit high quality video compression / Dual 10/100 Mb/s MAC interfaces
Brand / ROM size
AMI / 4MB
BIOS
Feature
Plug and Play (PnP) /PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE boot / ACPI 2.0
power management /Power on mode after power recovery /
User-configurable H/W monitoring / Auto-configurable of hard disk types
Operating System OS supported list
Please refer to our OS supported list.
FCC (DoC)
Class A
Regulation
CE (DoC)
Yes
Operating Temp.
10° C ~ 35° C (50° F~ 95° F)
Non-operating
Temp.
- 40° C ~ 70° C (-40° F ~ 158° F)
Operating
Environment
In/Non-operating
Humidity
90%, non-condensing at 35° C
RoHS
RoHS 6/6
Compliant
Yes
Barebone
(1) GT24B8236-IL Barebone
Heatsink / Cooler
(2) G34 CPU heatsinks
Rail kit
(1) CRAL-0031, sliding rail kit for KGT24/ KGT62
Mounting Ear
(1) mounting ear kit
Manual
(1) MB User's manual + (1) BB User's manual
Installation CD
(1) TYAN installation CD
Package Contains
Cable Power Cord
(2) CCBL-0310, US type power cord / (2) CCBL-0300, EU type power
cord
Optional
accessories
Peripheral
(1) CSTK-0080, Slim type DVD kit w/cables
22
http://www.tyan.com
1.4 Standard Parts List
This section describes GT24-B8236-IL package contents and accessories. Open the
box carefully and ensure that all components are present and undamaged. The
product should arrive packaged as illustrated below.
1.4.1 Box Contents
Component Description
1U chassis,(4) hot swap HDDbays
TYAN® S8236-IL system board
(pre-installed)
500W single Power Supply
450W Power Supply
(6) 40x28mm System FAN
(pre-installed)
M1008
LED control board (pre-installed)
M7016
Power Distribution Board
(pre-installed)
M1235 SATA/SAS HDD Backplane
M2091 PCI-E riser card
M2091-R PCI-E riser card
http://www.tyan.com
23
1.4.2 Accessories
If any items are missing or appear damaged, contact your retailer or browse
to TYAN
®
’s website for service: http://www.tyan.com
The web site also provides information of other TYAN
®
products, as well as
FAQs, compatibility lists, BIOS settings, etc.
TYAN® Motherboard
Drive CD
Heatsink x2
HDD Screw Pack Mounting Ears & Screws
AC Power Cord 125V
(US)
AC Power Cord 250V
(Europe)
Barebone Manual Mainboard Manual
Rail Kit
Rail with Bracket x 2 Screw Pack
http://www.tyan.com
24
1.6 About the Product
The following views show you the product.
1.6.1 System Front View
25
http://www.tyan.com
1.6.2 System Rear View
B8236G24V4H-IL / B8236G24W4H-IL
B8236G24W4HR-IL
http://www.tyan.com
26
1.6.3 LED Definitions
Front Panel
LED State Color Description
On Green System is turned on
Blinking Green System is under S1 or S3 state
Power LED
Off Off Power off
Blinking Green LAN active
On Green LAN linked
NIC1
off off LAN not linked
Blinking Green LAN active
On Green LAN linked
NIC2
off off LAN not linked
Blinking Green LAN active
On Green LAN linked
NIC3
off off LAN not linked
On Red
Fan fail /Over temperature
/Over voltage
Warning
LED
Off Off No failure
On Blue System identified
ID LED
Off Off System not identified
Rear I/O
LAN LED
LED State Color Description
On Green 10Mb/100Mb/1000Mb linked
Blinking Green 10Mb/100Mb/1000Mb activity
RJ-45
Activity(left)
Off Off No LAN linked
On Amber 1000Mb linked
On Green 100Mb linked
RJ-45
Linkage(Right)
Off Off 10Mb mode or No LAN linked
NOTE: “Left” and “Right” are viewed from the rear panel.
http://www.tyan.com
27
ID LED
LED State Color Description
On Blue System identified
ID LED
Off Off System not identified
HDD LED
HDD Status Status LED
2/4/6/8
Color: Amber
Activity LED
1/3/5/7
Color: Green
No Driver Present or power disconnected OFF OFF
No Activity OFF ONDriver Present
Access Activity OFF Blinking
HDD Fail On Solid OFF
Identify (Locate the HDD) Blinking(1Hz) x
SAS/SATA RAID Building Blinking(4Hz) x
Loading...