TYAN Transport GX15 B2723T15, Transport GX15 B2723T15M, B2723T15, Transport GX15, B2723T15M User Manual
B2723T15 /// Transport GX15
B2723T15M
Revision 1.0
Copyright © TYAN Computer Corporation, 2002-2003. All rights reserved. No
part of this manual may be reproduced or translated without prior written
consent from TYAN Computer Corp.
All registered and unregistered trademarks and company names contained in
this manual are property of their respective owners including, but not limited to
the following.
TYAN, Tiger i7501 S2723, Transport B2723T15, Tran sport B2723T15M,
Transport GX15 are trademarks of TYAN Computer Corpo ration.
Intel, Xeon and combinations thereof are trademarks of Intel Corporation.
AMI, AMIBIOS are trademarks of AMI Software Incorporated.
Microsoft, Windows are trademarks of Microsoft Corporation..
QLogic, Zircon, and combinations thereof are trademarks of QLogic
Corporation.
IBM, PC, AT, PS/2 are trademarks of IBM Corporation.
Winbond is a trademark of Winbond Electronics Corporation.
Portable Document Format (PDF) is a trademark of Adobe Corporation.
Information contained in this document is furnished by TYAN Computer
Corporation and has been reviewed for accuracy and reliability prior to printing.
TYAN assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN products including liability or
warranties relating to fitness for a particular purpose or merchantability. TYAN
retains the right to make changes to product descriptions and/or specifications
at any time, without notice. In no event will TYAN be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.
1
http://www.tyan.com
Table of Contents
Before you begin…
Chapter 1: Introduction
1.1 Congratulations
1.2 Hardware Specifications
1.3 Front View
1.4 Top View
Chapter 2: Hardware Installation
2.0 Installation Procedures
2.1 Opening the Chassis
2.2 Installing HDD
2.3 Installing Processor(s) and
heatsink(s)
2.4 Installing Add-on PCI Card
2.5 Installing Memory Modules
2.6 Installing Vent Duct
2.7 Finishing up
Chapter 3: Installing Into A Cabinet
or Telco Rack
3.0 Before you begin
3.1 Installing single system into a
19” cabinet
Chapter 4: Server Management Daughter
Card ( SMDC)
4.1 Summary
4.2 Features at a glance
4.3 Jumper setting
4.4 Specification
4.5 SMDC Features
4.6 Tyan System Operator (TSO)
summary
Appendix
Safety Document of system
Safety Document of SMDC
...……………………………………..Page 3
...……………………………………..Page 4
...……………………………………..Page 4
..….…………………………………..Page 5
...……………………………………..Page 6
.....………………………………… ..Page 7
...………………………………… ..Page 8
.…………………………………… ..Page 8
.…………………………………… ..Page 9
...………………………………… ..Page 10
...………………………………… ..Page 11
...………………………………… ..Page 12
...………………………………… ..Page 13
....…………………………………..Page 14
.....………………………………….Page 15
..……………………………………Page 16
..…..………………………………..Page 16
…...…..…………………………….Page 17
..………………………………..Page 18
….….….……..…………………….Page 18
..……..……………………………..Page 19
...……………………………………Page 20
…...…………………………………Page 20
….…………………………………..Page 25
…..………………………………….Page 31
…..………………………………….Page 32
.….………………………………….Page 32
.….………………………………….Page 33
2
http://www.tyan.com
Before you begin…
Check the box contents!
The barebone system package should contain the followin g:
1 x Tiger i7501 (S2723) motherboard (preinstalled)
2 sets x CPU retentions and clips
2 x Xeon Heatsink
1 x ATA 100 cable for HDD (pre-installed)
1 x Vent duct
2 x power cords (1 x compatible for standard US voltage, 1 x
compatible for standard German voltage)
1 x Tiger i7501 (S2723) User’s Manual
1 x Transport B2723T15/B2723T15M User’s Manual
1 x Tiger i7501 (S2723) Quick Reference
1 x TYAN driver CD
1 x screw
1x Tyan M3289 SMDC (optional item for B2723T15M)
1x 50-pin SMDC cable (optional item for B2723T15M)
If any of these items are missing, please contact your vendor/dealer for replacement
before continuing with the installation process.
3
http://www.tyan.com
Chapter 1: Introduction
1.1 – Congratulations!
Thank you for choosing the TYAN B2723T15/B2723T15M, the most compact Dual
Intel
®
Xeon processor platform for flexibility and productivit y. Based on Intel’s E7501
chipset, this powerful system is Hyper-Threading ready - utilizing onbo ard resources
so that a second thread of data can be processed in a single processor. Special
features of this system include IPMI Server Management, PCI-X support, one
10/100/1000 and one 10/100 Ethernet ports and onboard video.
Remember to visit TYAN’s Website at http://www.tyan.com
. There you can find
information on all of TYAN’s products with FAQs, distributors list and BIOS setting
explanations.
4
http://www.tyan.com
1.2 – Hardware Specifications
Form Factor:
• Optimized 1U form factor
• 14.5” inch in depth
• Dimensions (W x H x D):
482.6mm x 44mm x368.3mm
(19” x 1.73” x 14.5”)
Drive bays:
• 1 x internal 3.5” drive bay
Cooling Fans:
• 3 pcs 40x40x28 mm system fans with
tachometer monitoring
• Specially-designed CPU fan duct
Switch and LED Indicators:
• 1 x power switch
• 1 x reset switch
• 1 x power LED
• 1 x HDD LED
PSU:
• 300W EPS12V PSU (w/ active PFC)
System board:
• Tyan Tiger i7501 (S2723GNN)
Processor
• Dual mPG604 ZIF Socket
• Supports up to 2 x Intel
®
XEON
processors with 512KB of integrated L2
cache
• Supports processor speed up to 2.8GHz
• Front-Side Bus support for 533MHz
Chipset
• Intel
®
E7501 server chipset
• MCH + ICH3 + P64H2 + FWH
I/O Expansion
• 1x PCI-X expansion slot on riser card
Memory
• Four 184-pin 2.5-Volt DDR DIMM
sockets
• Supports up to 8GB of Registered DDR
RAM
• Supports only Registered ECC type
memory modules
Integrated LAN
• Two RJ-45 LAN Connectors with LEDs
• One 10/100
• One 10/100/1000
Server Management Daughter Card
(Option)
• Tailored for IPMI highest 1.5
specifications
• Supports flexible Windows and Linux
based
Management Solution
• Supports remote Power on/off and reset
support (IPMI-over-LAN)
BIOS
• AMI BIOS 8.0 on 4Mbit Flash ROM
• LAN remote boot (PXE) and SMBIOS
v2.3 support
• BIOS Boot Specification v3.1(BBS)
support
• Auto configuration of IDE hard disk
types
Regulatory
• FCC Class A certified
• European CE certified
(Declaration of Conformity)
Packing information
• Barebone weight: 11 kg
• Complete system weight: 11.5 kg
TYAN reserves the right to add support
or discontinue support for any OS
without notice.
5
http://www.tyan.com
1.3 – Front View
Powe
r
/HDD
LEDs
Power/
Reset
Switches
PS/2 Mouse and Keyboard
Double-deck USB 1.1 Port
A
dd-on PCI
Expansion Slot
Fast Ethernet w/ LED
VGA Port
Gigabit Ethernet w/ LED
6
http://www.tyan.com
1.4– Top View
Cooling Fans
CPU 2
EPS 12V
PSU
CPU 1
HDD
Riser card
Memory
Slots
SMDC
( Server
Management
Daughter Card)
7
http://www.tyan.com
Chapter 2: Hardware Installation
2.0 Introduction
You are now ready to install your system.
The first thing you should do is read this user’s manual. It contains important
information that will make installation and setup much easier. Here are some
precautions you should take when installing your system:
(1) Ground yourself properly before removing the top cover of the system. Unplug
the power from your computer power supply and then touch a safel y grounded
object to release static charge (i.e. power supply case). For the safest
conditions, Tyan recommends wearing a static safety wrist strap.
(2) Avoid touching the motherboard components, IC chips, connectors, memory
modules, and leads.
(3) Motherboard is pre-installed in the system, if, under any circumstances, it is
removed from the system, place the motherboard on a grounded antistatic
surface.
(4) Inspect the board and system for damage.
The following pages include details on how to install the processor, memory, disk drive
and cables.
NOTE
DO NOT APPLY POWER TO THE SYSTEM IF ANY PART OF THE
SYSTEM COMPONENTS HAS BEEN DAMAGED
8
http://www.tyan.com
2.1 Opening the chassis
2.1.1 Push the top cover toward back.
2.1.2 Lift up the top cover and remove it
from the chassis.
2.1.3 Top cover removed.
9
http://www.tyan.com
2.2 Installing HDD
2.2.1 Slide the HDD into place.
2.2.2 Connect the Power cable to HDD.
2.2.3 Connect ATA cable to HDD.
Note: ATA cable is pre-connected to M/B (J23).
2.2.4 Secure the drive with 4 screws from
the bottom of the chassis.
10
http://www.tyan.com
Loading...