Two Brothers Racing TRX700XX User Manual
Installation Instructions
Make sure the ATV is completely cool before starting
1.
the installation. Make sure the ATV is secure on
a level surface and the wheels are chocked to
prevent the ATV from rolling during installation.
Remove seat assembly.
2.
Install entire assembly onto header gently turning it into
6.
position so that the muffler bracket and the slip on tube
bracket line up with the appropriate holes and tighten. Use
the supplied 8x20mm flange bolt for upper muffler mount.
TM
2008 Honda
V.A.L.E.
V A R I A B L E A X I S L O C K I N G E X H A U S T
TRX700XX
V.A.L .E .™ S li p- on E xh au st S ys te m wi th M -7 Alu mi nu m Ca ni st er
Par t # 00 5- 2010 40 6V
Parts List
Qty. Description Part Number
1 TRX700XX (2008) M-7 Aluminum Exhaust Canister 005-201-206M
1 TRX700XX (2008) Stainless Steel Slip-On Tube 005-20104S
1 HARDWARE KIT 005-201-3
2 X-Ring (half) 005-7-2-3
1 8x20mm Flange Bolt 005-FB820
1 5mm Long Handle Ball End Hex Key 005-9-18610
4 M6 Split Lock Washer 005-WL6
4 6x14mm Socket Head Cap Screw 005-SH614
1 Torx Key 005-9-15820
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualied
technician. If you have any doubts as to your ability to install this
performance part, please consult with your local ATV dealer. Read all
instructions rst before starting installation. Make sure the ATV and
exhaust system are completely cool before starting the installation.
Also, make sure the ATV is secure on a level surface and the wheels are
chocked to prevent the ATV from rolling.
Warranty
Two Brothe rs Racing p roducts are intended fo r closed co urse compet ition purpo ses only, and therefore are sold “a s is”
without warranty. Two B rothers Rac ing specifi cally discla ims any war ranties of merchantabi lity or fit ness for a particular
purpose and discla ims all res ponsibility for conseq uential and incidental damages or any other losses aris ing from the
use of these produ cts or part s.
Remove the right side center cover to expose the clamp
3.
joining header and muffler.
Loosen the clamp and bolts holding the slip-on to the ATV,
4.
remove slip-on assembly.
Use the supplied 6x14mm socket head cap screws and
5.
slip lock washers to loosely attach the X-Lite™ ring to the
muffler inlet. Loosely tighten all four screws. Keep the
screws loose enough so that the tube can rotate back and
forth inside the V.A.L.E.™ Cap.
Muffler Inlet
X-Lite™ Ring
Slip Tube
V.A.L.E.™ Assembly Detail
Tighten the four (4) 6 x 14mm socket head cap
7.
screws to 7ft lbs. You may need to remove the
muffler to tighten all four allen head bolts after you
have snugged the muffler into position on the ATV.
Tighten the Canister mounting tab and
8.
slip on mounting bracket to 15-18 ft. lbs.
Before you run the ATV, clean off all fingerprints and dirt, as
9.
any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the ATV and
enjoy. It is normal for some white smoke to appear the
first time you start the ATV. This is packing/manufacturing
oil from inside the pipe burning off. After 30-60 minutes of
use, recheck all fasteners for tightness.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System:
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Titanium Header System:
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters:
bright finish to factory spec.
Brushed Aluminum Canisters:
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters:
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10 038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers:
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10 038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters at the first signs of packing material deterioration. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Polished stainless steel pipes will turn a light golden hue
Polished titanium pipes will experience color shift ranging
Use an aluminum or mag wheel polish to restore the
Clean using a mild water based spray cleaner. Always
Clean using a mild water based spray cleaner. Always apply
For cleaning use a mild water based spray cleaner. Always apply
V.A.L.E.
V A R I A B L E A X I S L O C K I N G E X H A U S T
TM
2008 Honda
TRX700XX
V.A.L .E .™ S li p- on E xh au st S ys te m wi th M -7 Alu mi nu m Ca ni st er
Par t # 00 5- 2010 40 6V
005-2010406V
Qty. Description Part Number
1 TRX700XX (2008) M-7 Aluminum Exhaust Canister 005-201-206M
1 TRX700XX (2008) Stainless Steel Slip-On Tube 005-20104S
1 HARDWARE KIT 005-201-3
2 X-Ring (half) 005-7-2-3
1 8x20mm Flange Bolt 005-FB820
1 5mm Long Handle Ball End Hex Key 005-9-18610
4 M6 Split Lock Washer 005-WL6
4 6x14mm Socket Head Cap Screw 005-SH614
1 Torx Key 005-9-15820
Loading...