Two Brothers Racing CRF150F User Manual
Installation Instructions
2007-10 Honda
CRF150R
V.A.L .E .™ S li p- On E xh au st S ys te m wi th M -7 C an is ter
Par t # 0 05 -17 2040 6V / 0 05 -1 72 04 07 V
V.A.L.E.
V A R I A B L E A X I S L O C K I N G E X H A U S T
Full system shown. Slip-on system does not include header.
TM
Parts List
Qty. Description Part Number
1 CRF150R Muffler Canister M-7 Varies
1 CRF150R S-Bend Tube Varies
1 HARDWARE KIT 005-172-3
1 CRF150R Side Panel Spacer 005-S-8225
1 8x35mm Flange Bolt 005-FB835
1 5mm Long Handle Ball end hex key 005-9-18610
4 6x14mm Socket Head Cap Screw 005-SH614
4 M6 Split Lock Washer 005-WL6
2 TBR Script Logo Yellow Decal 4” 015-10208-A
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualied
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read
all instructions rst before starting installation. Make sure the vehicle and
exhaust system are completely cool before starting the installation. Also,
make sure the vehicle is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Warranty
Two Brothe rs Racing p roducts are intended fo r closed co urse compet ition purpo ses only, and therefore are sold “a s is”
without warranty. Two B rothers Rac ing specifi cally discla ims any war ranties of merchantabi lity or fit ness for a particular
purpose and discla ims all res ponsibility for conseq uential and incidental damages or any other losses aris ing from the use
of thes e products or parts.
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on a centerstand
or ideally a service lift.
2. Remove right side panel.
3. Remove upper muffler mounting bolt.
4. Remove lower muffler mounting bolt.
5. Remove muffler assembly.
6. Assemble the V.A.L.E.™ unit. Use the 4 (four) 6 x 14mm
bolts and split lock washers to loosely attach the XLite ™
ring to muffler inlet.
7. Slip S-bend tube of V.A.L.E.™muffler assembly into head
pipe. Use supplied 8 x 35mm flange bolt and spacer to
loosely attach upper muffler mount and use the OEM
flange bolt to loosely attach the lower muffler mount.
Apply threadlock to mounting bolts and loosely secure.
Muffler Inlet
X-Lite™ Ring
S-Bend Tube
V.A.L.E.™ Assembly Detail
8. Making sure that the V.A.L.E.™assembly is oriented
correctly, securely tighten upper muffler mounting bolt.
9. Securely tighten the 4 (four) 6 x 14mm hex head bolts of
the V.A.L.E.™assembly.
10. Securely tighten the lower muffler mounting bolt.
11. Cut sid e p ane l f or upp er mou nt ing mu ff ler bo lt
cl ea ran ce an d r e-i ns tal l.
12. Double check to make sure that all hardware is tightened.
13. Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the first time you start the bike. This is packing/
manufacturing oil from inside the pipe burning off. Check
for gaps or leaks. If you find a leak, a little high temperature
silicon sealant should fix it. After 50 to 100 miles, recheck
all fasteners for tightness.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10 038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10 038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
M-7
Series
3.75” x 4.85” OVAL
V.A.L.E.
V A R I A B L E A X I S L O C K I N G E X H A U S T
TM
2007-10 Honda
CRF150R
Sl ip -O n V.A.L .E .™ E xh au st S ys te m wi th M -7 C an is ter
Par t # 00 5- 172 0406 V / 00 5- 17 20 40 7V
005-1720406V
Full System shown with header.
005-1720407V
Qty. Description Part Number
1 CRF150R Muffler Canister M-7 Aluminum 005-172-206M
1 CRF150R Aluminum S-Bend Tube 005-17201S
1 HARDWARE KIT 005-172-3
1 CRF150R Side Panel Spacer 005-S-8225
1 8x35mm Flange Bolt 005-FB835
1 5mm Long Handle Ball end hex key 005-9-18610
4 M6 Split Lock Washer 005-WL6
4 6x14mm Socket Head Cap Screw 005-SH614
2 TBR Script Logo Yellow Decal 4” 015-10208-A
Qty. Description Part Number
1 CRF150R Muffler Canister M-7 Carbon Fiber 005-172-207M
1 CRF150R Aluminum S-Bend Tube 005-17201S
1 HARDWARE KIT 005-172-3
1 CRF150R Side Panel Spacer 005-S-8225
1 8x35mm Flange Bolt 005-FB835
1 5mm Long Handle Ball end hex key 005-9-18610
4 M6 Split Lock Washer 005-WL6
4 6x14mm Socket Head Cap Screw 005-SH614
2 TBR Script Logo Yellow Decal 4” 015-10208-A
Loading...