Page 1
V.A.L.E.
Parts List
IMPORTANT - PLEASE READ CAREFULLY
Warranty
Two Brothers Racing pro ducts are i ntended for closed cou rse competit ion purpose s only, and t herefore ar e sold “as is”
without warranty. Two Bro thers Racin g specifica lly disclai ms any warr anties of m erchantabili ty or fitne ss for a pa rticular
purpose and disclai ms all respo nsibility f or conseque ntial and i ncidental d amages or a ny other lo sses arisin g from the use
of these products o r parts.
We recommend that this performance part be installed by a qualied
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions rst before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
2004-05 Kawasaki KX250F &
2004-06 Suzuki RMZ250
Sli p-on Exha ust S ystem with M-7 Cani ster
Part # 0 05-12 0040 6V / 005- 1200 407V
Qty. Description Part Number
1 M-7 Muffler Canister Varies
1 Stainless Steel S-Bend Tube 005-12001S
1 HARDWARE KIT 005-120-3
1 Side Panel Spacer 005-S-13
4 6x14mm Socket Head Cap Screw 005-SH614
1 8x25mm Flange Bolt 005-FB825
1 5mm Long Handle Ball End Hex Key 005-9-18610
4 Split Lock Washer 005-WL6
2 TBR Script Logo Yellow Decal 4” 015-10208-A
1 Spark Arrestor (aluminum canister only) 005-106S
Installation Instructions
Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on the sidestand or
ideally a rear service stand.
1. Remove right rear plastic panel to expose existing
exhaust system.
2. Remove bolt connecting existing exhaust canister to
frame.
3. Remove bolt at junction of existing connector &
headpipe.
4. Remove old muffler & connector tube.
5. Loosely attach the V
.A.L.E.™ muffler to the stainless steel
s-bend tube using the four supplied 6x14mm socket head
cap screws and split lock washers. Leave bolts loose for
now.
8. Insert the V
.A.L.E.™ assembly in from the rear of the bike.
Carefully rotate the pipe into position and slide it onto the
header.
7. Carefully rotate muffler assembly to align the 8x25mm
bolt with the mounting hole on the frame, insert the bolt
and loosely tighten.
8. Attach lower s-bend mount to subframe using OEM
hardare.
9. Once the muffler is aligned tighten the four 6mm x 14mm
V.A.L.E.™ screws with the supplied ball end hex key.
10. Tighten rear muffler top mount
11. Check your work and clean all fingerprints.
12. Re-install the plastic panel, and anything else that you
may have loosened or removed in order to install the
exhaust system.
13. Double check to make sure everything is aligned and
tighten all hardware.
14. Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the first time you start the bike. This is packing/
manufacturing oil from inside the pipe burning off. After
50 to 100 miles, recheck all fasteners for tightness.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Muffler Inlet
X-Lite™ Ring
Slip Tube
V.A.L.E.™ Assembly Detail
Page 2
V.A.L.E.
V A R I A B L E A X I S L O C K I N G E X H A U S T
TM
2004-05 Kawasaki KX250F &
2004-06 Suzuki RMZ250
Sli p-on Exha ust S ystem with M-7 Cani ster
Part # 0 05-12 0040 6V / 005- 1200 407V
Qty. Description Part Number
1 M-7 Muffler Canister 005-120-206M
1 Stainless Steel S-Bend Tube 005-12001S
1 HARDWARE KIT 005-120-3
1 Side Panel Spacer 005-S-13
4 6x14mm Socket Head Cap Screw 005-SH614
1 8x25mm Flange Bolt 005-FB825
1 5mm Long Handle Ball End Hex Key 005-9-18610
4 Split Lock Washer 005-WL6
2 TBR Script Logo Yellow Decal 4” 015-10208-A
1 Spark Arrestor (aluminum canister only) 005-106S
Qty. Description Part Number
1 M-7 Muffler Canister 005-120-207M
1 Stainless Steel S-Bend Tube 005-12001S
1 HARDWARE KIT 005-120-3
1 Side Panel Spacer 005-S-13
4 6x14mm Socket Head Cap Screw 005-SH614
1 8x25mm Flange Bolt 005-FB825
1 5mm Long Handle Ball End Hex Key 005-9-18610
4 Split Lock Washer 005-WL6
2 TBR Script Logo Yellow Decal 4” 015-10208-A
1 Spark Arrestor (aluminum canister only) 005-106S
Loading...