Twitoplast OPAL EL Installation And Operating Instructions Manual
2
®
EL
NEW
ELECTRICAL OPERATION
(FOR DAMPER)
INSTALLATION AND OPERATING
INSTRUCTIONS
EL WALL – MOUNT
Twitoplast Company thanks you for purchasing the Opal
El –Electrical Operation.The Opal EL device enables
zone/room temperature control, by means of adjusting
the airflow through the damper. The Opal EL device
was designed for optimal use to insure both quick
installation and comfortable & perfect air condition
temperature.
INSTALLATION AND OPERATING
INSTRUCTIONS
1. Stand Alone:
The Opal EL controls one
Damper.
9 Drezner St. Segula Industrial Zone,
Petach Tikva 49277, ISRAEL
Tel: 972-3-9345888 Fax: 972-3-9042729
e-mail:export@twitoplast.co.il
®
http/www.twitoplast.co.il
®
Containing :
• Opal EL – Dimmer.
• RJ-11 Cable.
• Red & Black ±Cable.
• Electrical Motor C508-TW .
• Installation & Operating
Instructions.
Please note: 12 VAC Only
Transformer
not included.
Can be purchased separately.
1 OPAL EL
2 Transformer 12 vac only
3 C508 Motor
4 RJ-11 cable
5 Motor cable±
WALL
MOUNT
The Opal EL controls one Damper, but has also an
affect on the A/C operation it self through the Zone
Control System ZC207
System Configurations
2. As an Integral part of
ZC-107 system.
1
2
3
5
®
9 Drezner St. Segula Industrial Zone,
Petach Tikva 49277, ISRAEL
Tel: 972-3-9345888 Fax: 972-3-9042729
e-mail:export@twitoplast.co.il
Put back the front
panel of the Opal EL
to the plastic box.
Assemble the front
panel of the Opal EL
to its base using the
screw. put back the
round knob.
Take out the wires from
the designate place in
the plastic box (by
cutting the plastic with
a knife or drilling)
( Step 6 )
6
8
7
C508-TW Motor
5
Remove the round
knob and the screw.
fasten the plastic box
to the well.
(step 1,2,3)
1
Cut Here
4
Entry of
the
motor
damper
3
Plastic Box
2
Entry
of the
AC
12v
(Step 7 & 8)
Connecting
Scheme
Stand alone
Connection of the OPAL EL to the
Zone control System OPAL ZC-207
Step1:
Connect the RJ-11 Cable
from the Opal EL to one
of the channels on
ZC-207
Step2:
Connect one Black &
Red Cable ± from the
motor damper to the ZC207 channel near the RJ11 (Red wire one+).
Step3:
Remove Black covering
from jumpers JP2 and JP3.
and add one of them to
Jumper J4 (see pic. 4).
Repeat steps 7&8
Repeat step 1&2 (stand alone).
CH1
CH2
CH2CH2
CH2
CH2
CH2
CH2
ZC 207
+
-
Motor
Connect the:
12 v power supply
cable from the
transformer to the
Opal EL.
Red & Black ±cable from
the Opal EL to the motor
(Red one+).
(step 4 & 5).
PLEASE NOTE:
There are two jumpers
JP2 & JP3.
Do not Remove the
Black Covering.
1.
2.
1
3
Step
Step
Step
Step
Step
Step
Step
Step
Installation of
the Opal EL
+
-
Motor
J4
RJ 11
C191
J2
J3
12Vac
Transformer
J4
RJ 11
C191
J4
J2
J3
RJ11
Loading...