Twister AL46-05R, AL46-30R, AL46-50R, AL46-100R, AL46-05G User Manual

Introduction

Thank you for selecting Twister. Twister is a four-channel DMX laser which can be
controlled via a standard DMX controller. It is a lightweight, mini intelligent fixture
and is an ideal product for discos, small clubs, exhibitions and any place that need
visionary effect. Twister creates exciting dual beam show with double scanner action
and four operating modes. For safe operation, read this manual before powering or
installing the fixture, follow the safety precautions listed below, and observe all
warnings printed in this manual and on the fixture.

Safety Precautions

 Do not spill liquids in to or on to your unit. If this ever happens, disconnect the main

power immediately. Do not connect this unit to any dimmer pack.

 Always disconnect from main power before making any type of connection.
 Be sure to locate this unit in a place with adequate ventilation at least 15 cm from a

wall, and mount this unit in safe and stable matter.

 To prevent fire or shock hazard, do not expose this unit to a high temperature or

high humidity area. Please unplug unit when not in use.

 Always keep combustible materials away from the fixture.
 This unit is intended for indoor use. Use of this unit outdoors voids all warranties.
 Always refer service to a qualified technician. Never look directly into laser beam.
 Occasional breaks are necessary to prevent breakdowns. Top Panel
 Caution - Use of controls or adjustments or performance of procedures other

than as specified herein may result in hazardous radiation exposure!

Set Up

Unpacking

Twister comes with: 1 hanging bracket, 2 clamp levers, 2 washers, 1
power cord and 1 user manual. Unpack carefully and be sure that no damage has
occurred during shipping. If there is anything missing or appear to be damaged
please contact your dealer.
Power Connection Be sure the source voltage in your area matches the required
voltage for your Twister before plugging your unit in. Incorrect voltage selection will
detrimentally affect the operation of this product.
DMX Cable Connection Twister is a four-channel DMX fixture that can be
operated with universal DMX controller. This unit and DMX controller require a
standard 3-pin XLR connector for data input and data output.
Installation/Mounting Twister should be properly mounted by using a suitable
hanging clamp and safety cable. Use in a well-ventilated area. Be sure no
ventilation slots are blocked.

Safety Label Position

Front Panel Bottom Panel

Left and Right Side Panel

Control Panel Introduction

6 5 4 1

7 23

Certification, identification and warning label

Warning label

Laser aperture & aperture label

1 Power Cord Connection
2 Fuse
3 Power Switch
4 Sensitivity Adjustment Knob
5 Microphone
6 DMX In & Out
7 DIP Switch Pin

Operating Modes (Cont.)

DMX Signal Levels

Channel 1

Channel 2

Range Lines Selection Range Patterns Selection

226-255

Lines change every 5

seconds

221-255

Automatically change all the

patterns in every 10 seconds

208-225

Lines change every 3

seconds

204-220 Sound Active Mode

157-207 Dotted Line 3 199-203

Pattern 15

185-198

Pattern 14

105-156

Dotted Line 2

53-104

Dotted Line 1

：
：
：

：
：
：

1-52

Line

31-44 Pattern 3

17-30 Pattern 2

4-16 Pattern 1

0

Off

0-3 Off

Operating Modes (Cont.)

DMX Signal Levels

Channel 3

Channel 4

Range Mirror Rotation No. 1 Range Mirror Rotation No. 2

228-255 Sound Active 228-255 Sound Active

224-227

Counterclockwise Fast

224-227

Clockwise Fast

220-223

Counterclockwise Medium

220-223

Clockwise Medium

216-219

Counterclockwise Slow

216-219

Clockwise Slow

213-215 Stop 213-215 Stop

209-212

Clockwise Slow

209-212

Counterclockwise Slow

205-208

Clockwise Medium

205-208

Counterclockwise Medium

201-204

Clockwise Fast

201-204

Counterclockwise Fast

200

0

0 360

360°

200

0

-0 -360

-360°