Twin-Star International Corner Mantel, Wall Mantel Assembly & Instruction Manual

INSTRUCTION MANUAL ENCLOSED

MANUEL D’INSTRUCTION À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

STOP

STOP

ATTENTION

IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL

OR CALL CUSTOMER SERVICE BEFORE YOU RETURN

THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.

For Customer Service:

www.twinstarhome.com

in English Call: 866-661-1218

ARRÊT

SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,

ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU

APPELEZ LE SERVICE À LA CLIENTÈLE AVANT DE RETOURNER

CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.

ATTENTION

ARRÊT

Pour le service à la clientèle:

www.twinstarhome.com

pour le service en français: 866-661-1219

PARE

SI TIENE ALGÚN PROBLEMA O PREGUNTAS, ENVÍE UN

MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO

DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER ESTE

PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.

ATENCIÓN

Servicio de atención al cliente:

PARE

www.twinstarhome.com

Línea para llamadas en español: 866-661-1219

INSTRUCTION MANUAL ENCLOSED

MANUEL D’INSTRUCTION À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

1

ELECTRIC FIREPLACE MANTEL

Requires-Electric Fireplace
Insert with Heater

26DE6439

ASSEMBLY INSTRUCTION

Españo p. 8

Français p. 15

Corner Mantel

Twin-Star International, Inc.
Delray Beach, FL 33445

Made in China
Printed in China

For Customer Service:

www.twinstarhome.com

English Call: 866-661-1218

Spanish /French Call: 866-661-1219

1

Wall Mantel

ATTENTION

Requires-Electric Fireplace
Insert with Heater

PACKAGE CONTENTS

M

N

G

K

I

F

D

L

E

J

C

B

H

A

Part Description Quantity

A Hearth/Base 1
B Left Front Panel 1
C Right Front Panel 1
D Center Front Panel 1
E Left Side Panel 1

F Right Side Panel 1
G Mantel/Top 1
H Drawer 1

I Upper Shelf 1

J Lower Shelf 1
K Upper Back Panel 1

L Lower Back Panel 1
M “L” Corner Brace 1
N Top Corner Extension 1

2

HARDWARE CONTENTS

Part

Description

Quantity

Picture
(Shown to size)

AA

BB

CC

DD

EE

ZZ

Bolt

Washer

Wood Dowel

Screw

Knob (with bolt)

Touch-up Pen

36

36

32

34

2

1

SAFETY INFORMATION

WARNING

• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.

CAUTION

• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.

• Do not sit on any part of the mantel.

• All panels are labeled left and right as viewed from the front of unit.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.

Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife

3

ASSEMBLY INSTRUCTIONS

1. Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Locate the Upper Shelf (I) and Lower Shelf (J) to
Left Side Panel (E) and Right Side Panel (F).Using
Bolt (AA) and Washer (BB) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.

Hardware Used

AA

BB

CC

Bolt

Washer

Wood Dowel

x 8

x 8

x 8

2. Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Connect the Left Front Panel (B), Right Front Panel
(C) and Center Front Panel (D) with connection
plate, tighten Screws (DD) through the pre-drilled
holes.
HAND TIGHTEN ONLY.

Fig. 1

CC

AA

BB

F

I

J

E

Fig. 2

D

Hardware Used

AA

CC

DD

Wood Dowel

Screw

x 4

x 2

3. Locate assembly from Step 1 and Step 2.
Set out fi nished side up for assembly from Step 2
on the fl oor, attached to assembly from Step 1 Using
Bolts (AA) and Washer (BB) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.

Hardware Used

AA

Bolt

x 10

Fig. 3

CC

C

DD

AA
BB

AA
BB

B

BB

Washer

x 10

4

4. Locate Hearth/Base (A) and set out fi nished side up
on the fl oor .
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Attach the Completed assembly from step 3 to the
Hearth/Base (A). Make sure that dowels (CC) are
seated into the pre-drilled holes in the Hearth/Base.
Using Bolts (AA) and Washers (BB) attach panels
through pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.

Hardware Used

Fig. 4

AA
BB

AA

BB

AA

CC

Bolt

Washer

Wood Dowel

x 6

x 6

x 8

5. Insert one Wood Dowel (CC) into each of the
pre-drilled holes on the top edges of the Assembly
from step 4. Then locate Mantel/Top (G) and lay
fi nished side up on top of completed assembly. From
the inside, attach Mantel/Top using Bolt (AA) and
Washer (BB) through the pre-drilled holes in the
mounting blocks.
HAND TIGHTEN ONLY.
Using Phillips head screwdriver tighten all Bolts
alternating top and bottom, left and right.

Hardware Used

AA

Bolt

x 6

CC

A

Fig. 5

G

CC

BB
AA

BB

AA

CC

Washer

Wood Dowel

x 6

x 8

6. Locate Upper Back Panel (K) and Lower Back Panel
(L). Attach to the Back of completed assembly from
Step 5, Using a Phillips Head screw driver, tighten
Screws (DD) to through the pre-drilled holes in
Upper Back Panel and Lower Back Panel to the
completed assembly.

Hardware Used

DD

Screw

x 32

Fig. 6

K

DD

L

5

7. Carefully align the metal tracks on the left and right
sides of box with the extended glides. Make sure
Drawer (H) are aligned and centered in cabinet, then
gently push the drawer into place.
Attach the Knob (EE) to the drawer, use the bolts
attached through the pre-drilled holes in the
drawers. Then use a Phillips Head Screw Driver to
tighten the bolts.

Hardware Used

Fig. 7

EE

Knob (with bolt) x 2

8. Remove the two mounting brackets attached to the
back of the Left and Right Front panels. Set aside
with the wood screws.

PLEASE READ ALL “ELECTRIC FIREPLACE
INSERT” INSTRUCTIONS PRIOR TO INSTALLING
ELECTRIC INSERT IN YOUR COMPLETED
FIREPLACE MANTEL. INSTALL THE INSERT IN
YOUR FIREPLACE CLOSE TO ITS FINAL
POSITION.

Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across Hearth/Base as it may scratch your unit.
Install the mounting brackets to hold insert fl ush
against the inside of the mantel front panel.

MOVE YOUR COMPLETED UNIT ONLY SHORT
DISTANCES. MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO PEOPLE TO
MOVE COMPLETED UNIT INTO ITS FINAL
POSITION.

EE

H

Fig. 8

Install
Insert
From
Back

Electric

Fireplace Insert

Completed
Unit

6