Twin-Star International 36WM2383 Assembly Instruction Manual
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
STOP
STOP
ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service: www.twinstarhome.com
in English Call: 866-661-1218
in Spanish Call: 866-661-1218
in French Call: 866-374-9203
PARE
PARE
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS,
ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER
ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente: www.twinstarhome.com
Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en español: 866-661-1218
Línea para llamadas en francés: 866-374-9203
ARRÊT
ATTENTION
ARRÊT
SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE
SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle : www.twinstarhome.com
pour le service en anglais, composez le 866-661-1218
pour le service en espagnol, composez le 866-661-1218
pour le service en français, composez le 866-374-9203
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
1
ELECTRIC FIREPLACE MANTEL
36WM2383
ASSEMBLY INSTRUCTION
Españo p. 7
Français p. 13
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
For Customer Service:
www.twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
1
ATTENTION
Requires-Electric Fireplace Requires-Electric Fireplace
Insert with HeaterInsert with Heater
PACKAGE CONTENTS
G
C
F
D
I
I
E
B
J
J
J
H
A
Part Description Quantity
A Hearth/Base 1
B Left Front Panel 1
C Right Front Panel 1
D Center Front Panel 1
E Left Side Panel 1
F Right Side Panel 1
G Mantel/Top 1
H Center Lower Front Panel 1
I Connect Block 2
J Center Support Panel 3
2
HARDWARE CONTENTS
Part
AA
BB
CC
DD
EE
Description
Bolt
Washer
Wood Dowel
Screw ø4*50mm
Metal “L” Bracket
Quantity
33+1 extra
33+1 extra
37+1 extra
2
2
Picture
FF
GG
HH
ZZ
Screw ø4*19mm
Screw ø3*14mm
Wall Anchor
Touch-up Pen
4
4
2
1
SAFETY INFORMATION
WARNING
• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
• Do not sit on any part of the mantel.
• All panels are labeled left and right as viewed from the front of unit.
3
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife
ASSEMBLY INSTRUCTIONS
1. Locate the Center Front Panel (D), Center Lower
Front Panel (H), Right Front Panel (C) and Left
Front Panel (B) and set out face down on a
scratch-free surface.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Push the Right Front Panel and Left Front Panel
snug to the center front panel (D) and center lower
front panel (H). Make sure the Wood Dowels are
seated in the pre-drilled holes. Insert Bolts (AA) and
Washers (BB) into the holes in the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
AA
BB
CC
Bolt
Washer
Wood Dowel
x 4
x 4
x 8
2. Locate Hearth/Base (A) and set out finished side up
on the floor.
Insert one Wood Dowel (CC) into each of the
pre- drilled holes.
Attach the completed Front panel assembly from
step 1 and Center Support Panel (J) to the
Hearth/Base (A). Make sure the dowels are seated
into the pre-drilled holes in the Hearth/Base. Using
Bolts (AA) and Washers (BB) attach panels through
pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Fig. 1
Fig. 2
CC
C
CC
CC
D
B
BBBBBB
AAAAAA
H
CC
BB
AA
AA
BB
Hardware Used
AA
BB
CC
Bolt
Washer
Wood Dowel
x 8
x 8
x 11
A
CC
CC
J
4
3. Locate Left Side Panel (E) and Right Side Panel (F),
insert one Wood Dowel (CC) into each of the
pre-drilled holes. Attach to the completed front panel
assembly and Hearth/Base using Bolts (AA) and
Washers (BB) through the pre-drilled holes in the
mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
AA
BB
Bolt x 10
Washer x 10
Fig. 3
BB
AA
E
AA
F
BB
CC
Wood Dowel
x 4
4. Locate Mantel Top (G) and set out face down on a
non-scratch surface. Attach the Metal “L” Bracket
(EE) to underside of the Mantel/Top (G) as diagram,
tighten Screw (GG) through the pre-drilled holes.
You may want to adjust the position of Metal “L”
Brackets to align with wall studs.
Hardware Used
GG
EE
Screw ø3*14mm
Metal “L” Bracket
x 4
x 2
CC
Fig. 4
GG
EE
G
5. Insert one Wood Dowel (CC) into each of the
pre-drilled holes on the top edges of the Assembly
from step 3. Then locate Mantel/Top (G) and lay
fi nished side up on top of completed assembly.
From the inside, attach Mantel/Top (G) using Bolts
(AA) and Washers (BB) through the pre-drilled holes
in the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
AA
BB
CC
Bolt
Washer
Wood Dowel
x 7
x 7
x 10
Fig. 5
G
BB
AA
CC
5
Loading...