Twin-Star International 23TF2322 Assembly Instructions Manual
ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service: email: parts@twinstarhome.com
in English Call: 866-661-1218
in Spanish Call: 866-661-1218
in French Call: 866-374-9203
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS,
ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER
ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente: Correo electrónico: parts@twinstarhome.com
Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en español: 866-661-1218
Línea para llamadas en francés: 866-374-9203
STOP
STOP
PARE
PARE
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE
SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle : courriel : parts@twinstarhome.com
pour le service en anglais, composez le 866-661-1218
pour le service en espagnol, composez le 866-661-1218
pour le service en français, composez le 866-374-9203
ARRÊT
ARRÊT
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
E-1
WOOD FIREPLACE MANTEL
23TF2322
WOOD MANTEL ASSEMBLY INSTRUCTIONS
PARTS LIST
Description
PARTS
Hearth/Base
Center Left Side Panel
Center Right Side Panel
Center Shelf
Left Side Panel
Right Side Panel
Mantel/Top
Wood Shelf
Center Back Panel
Left Front Door
Right Front Door
Side Back Panel
Center Front Bar
Positioning Panel
Stabilizer Frame
Securing Block
HARDWARE
Bolt 1/4 in. x 1-1/4 in.
Washer 1/4
Wood Dowel
Shelf Pin
Screw
Screw 5/32”*1/2”
Screw 5/32”*1”
Door Clip
Handle (With Bolt)
Tipping Restraint Hardware
Touch Up Pen
Part
A
B
C
D
E
F
G
H
I
J
K
P
S
T
U
Y
L
M
N
O
Q1
Q2
Q3
R
V
W
Z
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
28+1 extra
28+1 extra
26+1 extra
4
24+1 extra
2
7
1
2
2
1
ALSO Requires-Electric
ALSO Requires-Electric
Fireplace Insert with Heater
Fireplace Insert with Heater
E-mail: parts@twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
ATTENTION
For Customer Service:
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
E-2
For a complete tight fi t every bolt
should have a fl at washer.
All panels are labeled Left and Right as
viewed from the front of unit.
1. Locate the Center Left Side Panel (B), Center
Right Side Panel (C), Center Shelf (D), and
set out face down on a scratch-free surface.
2. Insert one Wood Dowel (N) into each of the
pre-drilled holes.
3. Push the Center Left Side Panel and Center
Right Side Panel snug to the Center Shelf (D).
Make sure the Wood Dowels are seated in
the pre-drilled holes.
HAND TIGHTEN ONLY.
Center
Left
Side
Panel
Center
Right
Side
Panel
Center Shelf
L
M
N
N
N
B
C
D
PLEASE READ AND FOLLOW ALL SAFETY TIPS
GETTING STARTED
1. Before assembly, CAREFULLY use scissors or utility knife to cut and unwrap all parts. Make
sure you do not discard the hardware.
2. Make sure that you have all the parts listed. If you are missing any parts please email Customer
Service: parts@twinstarhome.com or call 1-866-661-1218 in English, 1-866-374-9203 in French
or 1-866-661-1218 in Spanish. Please identify the parts you need and model number. Make sure
to include your name and address.
CAUTION:
DO NOT MOVE MANTEL OR INSERT WHILE PLUGGED INTO POWER SUPPLY.
HELPFUL HINTS
• Some steps are more easily handled with two adults.
• Attach the fi replace insert to the completed wood mantel last. INSTALL INSERT IN FROM THE
BACK OF THE FIREPLACE SO AS NOT TO SCRATCH THE HEARTH/BASE.
• Use care in assembling your new fi replace, take your time and use the hardware provided and a
quality Phillips head screwdriver. NEVER OVER TIGHTEN BOLTS.
• Do not sit on any part of the mantel.
CARE & CLEANING
1. Dust your fi replace regularly with a soft non-lint producing cloth or household dusting product.
2. You can clean your fi replace with a gentle non-abrasive household cleaner. Make sure to dry your
fi replace immediately with a soft cloth or towel.
E-3
8. Insert wood dowel (N) into the holes in the
Center Left/Right Side Panel (B/C), push
Center Front Bar (S) snug to the Center
Left/Right Side Panel (B/C).
9. Connect the Center Front Bar (S) to the
Left/Right Side Panel (E/F) with Bolts (L)
and Washers (M) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.
4. Locate Hearth/Base (A) and set out fi nished
side up on the fl oor.
5. Insert one Wood Dowel (N) into each of the
pre-drilled holes.
6. Attach the Completed Center Front assembly
from step 3 to the Hearth/Base (A). Make
sure that dowels are seated into the
pre-drilled holes in the Hearth/Base. Using
Bolts (L) and Washers (M) attach panels
through pre-drilled holes in the mounting
blocks.
HAND TIGHTEN ONLY.
7. Locate Left Side Panel (E) and Right Side
Panel (F), insert one Wood Dowel (N) into
each of the pre-drilled holes on the bottom
edge of the panels. Then use Bolts (L) and
Washers (M) through the pre-drilled holes
in the mounting blocks. Attach the Side
Panels to Hearth / Base (A).
HAND TIGHTEN ONLY.
Left
Side
Panel
Right
Side
Panel
Hearth/Base
Center Front Bar
L
L
L
N
N
N
N
N
N
A
S
N
N
N
M
M
M
E
F
E-4
I
Q1
Q1
Center
Back
Panel
P
Mantel/Top
G
L
M
Side
Back
Panel
10. Insert one Wood Dowel (N) into each of the
pre-drilled holes on the top edges of the
Assembly from step 9. Then locate
Mantel/Top (G) and lay fi nished side up on
top of completed assembly. From the inside,
attach Mantel/Top (G) using Bolts (L) and
Washers (M) through the pre-drilled holes in
the mounting blocks.
HAND TIGHTEN ONLY.
11. Using Phillips head screwdriver tighten all
Bolts alternating top and bottom, left and
right.
12. Locate Center Back Panel (I), attached to
the left back of the completed assembly
from step 11, using a Phillips Head
screwdriver, tighten screws (Q1) through the
pre-drilled holes in the Left Back Panel to
the completed assembly.
13. Locate Side Back Panel (P), attached to
the right back of the completed assembly
from step 11, using a Phillips Head
screwdriver, tighten screws (Q1) through the
pre-drilled holes in the Right Back Panel
to the completed assembly.
N
N
N
N
E-5
a
b
c
1
2
3
Left
Front
Door
Right
Front
Door
Handle
(with bolt)
K
V
J
14. Locate Right Front Door (K) and Left
Front Door (J). Slide door hinge keyhole
into panel hinge bracket. (Diagram 1)
Use Phillips Head Screwdriver to tighten
screws. (Diagram 2)
TO ADJUST HINGES
To adjust door forward or backward change
keyhole slot position.
(As Shown In Diagram 3a)
To adjust door right or left loosen / tighten
screw.
(As Shown In Diagram 3b)
To adjust door up or down adjust
bracket height.
(As Shown In Diagram 3c).
15. Attach the Handle (V) to the Left Front
Door (J) and Right Front Door (K), use
the bolts attached through the pre-drilled
holes in the doors. Then use a Phillips
Head Screwdriver to tighten the bolts.
16. There are levelers located under the mantel
which the height can be increased by
twisting counter-clockwise.
PLEASE READ ALL “WINE COOLER”
INSTRUCTIONS PRIOR TO
INSTALLING THE
THERMOELECTRIC COOLER IN
YOUR MANTEL.
17. Insert the wine cooler feet into the holes
of the Positioning Panel (T). Push the
panel forward until the cooler makes
contact with the front frame of the mantel.
Positioning
Panel
T
Leveler
E-6
O
H
R
Q2
Q3
T
U
Q3
Q3
Shelf Pin
Stabilizer
Frame
Positioning
Panel
Door
Clip
Wood
Shelf
18. Open the Right Front Door (K) and cooler
door, connect the Right Front Door (K) to the
cooler door with the Door Clip (R). Close
door and adjust the wine cooler forwards or
backwards to insure a smooth operation of
the door with a tight seal.
Note: Installing the clip with the door
open at a 45 degree angle will help
insure a smooth operation through
the full motion of the door.
19. Choose desired height of Shelf (H) and
place the four Shelf Pin (O) into same height
shelf holes inside side panels. Insert Wood
Shelf (H), allow Wood Shelf (H) to rest
on the Shelf Pin (O).
20. Insert Stabilizer Frame (U) once the cooler is
in the correct position. Fasten the positioning
panel with wood screws (Q3). Wedge the
Stabilizer Frame (U) between the top of the
cooler and mantel. Fasten with wood screws
(Q3).
Loading...