Twin-Star International 23MM1824 Assembly Instruction Manual

INSTRUCTION MANUAL ENCLOSED

MANUEL D’INSTRUCTION À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

STOP

STOP

ATTENTION

IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL

OR CALL CUSTOMER SERVICE BEFORE YOU RETURN

THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.

For Customer Service: www.twinstarhome.com

in English Call: 866-661-1218
in Spanish Call: 866-661-1218
in French Call: 866-374-9203

PARE

PARE

ATENCIÓN

SI TIENE ALGÚN PROBLEMA O PREGUNTAS,

ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO

DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER

ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.

Servicio de atención al cliente: www.twinstarhome.com

Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en español: 866-661-1218
Línea para llamadas en francés: 866-374-9203

ARRÊT

ATTENTION

ARRÊT

SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,

ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE

SERVICE À LA CLIENTÈLE AVANT DE RETOURNER

CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.

Pour le service à la clientèle : www.twinstarhome.com

pour le service en anglais, composez le 866-661-1218
pour le service en espagnol, composez le 866-661-1218
pour le service en français, composez le 866-374-9203

INSTRUCTION MANUAL ENCLOSED

MANUEL D’INSTRUCTION À L’INTÉRIEUR

MANUAL DE INSTRUCCIONES ADJUNTO

1

ELECTRIC FIREPLACE MANTEL

23MM1824

ASSEMBLY INSTRUCTION

Españo p. 7

Français p. 13

Twin-Star International, Inc.
Delray Beach, FL 33445

Made in Vietnam
Printed in Vietnam

For Customer Service:

www.twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218

1

ATTENTION

Requires Electric Fireplace Requires Electric Fireplace
Insert with HeaterInsert with Heater

PACKAGE CONTENTS

G

M

J

L

K

I

D

C

H

I

B

N

E

H

A

Part Description Quantity

A Hearth/Base 1
B Center Left Side Panel 1
C Center Right Side Panel 1
D Center Front Panel 1
E Left Side Panel 1
F Right Side Panel 1
G Mantel/Top 1
H Wood Shelf 2

I Side Back Panel 2

J Center Back Panel 1
K Center Shelf 1

L Center Front Bar 1

M Center Back Bar 1
N Insert Support Bar 1

F

2

HARDWARE CONTENTS

Part

Description

Quantity

Picture
(Shown to size)

AA

BB

CC

DD

EE

ZZ

Bolt

Flat Washer

Wood Dowel

Wood Screw

Shelf Pin

Touch-up Pen

30+1 extra

30+1 extra

30+1 extra

34

8

1

SAFETY INFORMATION

WARNING

• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.

CAUTION

• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.

• Do not sit on any part of the mantel.

• All panels are labeled left and right as viewed from the front of unit.

3

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.

Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife

ASSEMBLY INSTRUCTIONS

1. Locate the Center Left Side Panel (B), Center Right
Side Panel (C), Center Front Panel (D), and set out
face down on a scratch-free surface.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Push the Center Left Side Panel and Center Right
Side Panel snug to the Center Front Panel. Make
sure the Wood Dowels are seated in the pre-drilled
holes.
Connect the Center Left Side Panel (B), Center
Right Side Panel (C) and Center Front Panel (D)
with Connection Plate, tighten Screws (DD) through
the pre-drilled holes.

Hardware Used

CC

DD

Wood Dowel
Screw x 2

x 4

2. Insert one Wood Dowel (CC) into each of the
pre-drilled holes.

Locate the Center Shelf (K) on the top of the
assembly from the step 1, as shown in diagram.
Make sure that dowels are seated into the pre-drilled
holes.
Using Bolts (AA) and Washers (BB) attach these
panels through pre-drilled holes in the mounting
blocks.

HAND TIGHTEN ONLY.

Hardware Used

AA

BB

Bolt x 6
Flat Washer x 6

Fig. 1

CC

C

Fig. 2

CC

CC

D

B

DD

K

CC

D

B

C

BB

AA

CC

Wood Dowel

x 4

4

3. Locate the left / right side panel (E,F) and Center
front/ back bar (L,M), Insert one Wood Dowel (CC)
into each of the pre-drilled holes. Push the side
panels snug to the center front/back bar (L,M) and
center shelf (K), Connect the front bar and the side
panels by connection plate, tighten Screw(DD)
through the pre-drilled holes. Using Bolt (AA)
through Washer (BB) to connect the center shelf
and side panels together.

Hardware Used

AA

Bolt

x 4

Fig. 3

CC

DD CC

L

M

E

BB

CC

Flat Washer

Wood Dowel

x 4
x 10

4. Locate Hearth/Base (A) and set out fi nished side up
on the fl oor. Insert one Wood Dowel (CC) into each
of the pre-drilled holes. Attach the Completed
assembly from step 3 to the Hearth/Base (A). Make
sure the dowels are seated into the pre-drilled holes
in the Hearth/Base. Using Bolts (AA) and Washers
(BB) attach panels through the pre-drilled holes in
the mounting blocks.

Hardware Used

AA

BB

CC

Bolt
Flat Washer

Wood Dowel

x 8
x 8
x 8

F

Fig. 4

BB

AA

AA
BB

A

CC

5. Insert one Wood Dowel (CC) into each of the
pre-drilled holes on the top edges of the Assembly
from step 4. Then locate Mantel/Top (G) and lay
fi nished side up on top of completed assembly.
From the inside, attach Mantel/Top (G) using Bolts
(AA) and Washers (BB) through the pre-drilled holes
in the mounting blocks.
HAND TIGHTEN ONLY.

Using Phillips head screwdriver tighten all Bolts
alternating top and bottom, left and right.

Hardware Used

AA

BB

CC

Bolt
Flat Washer

Wood Dowel

x 10
x 10
x 4

Fig. 5

G

CC

CC

BB
AA

5