TVS electronic RP-35 User Manual

Download

Page 1

MODEL : Jus’ Bill RP-35

Mini Dot Impact Printer

All specifications are subject to change without notice

Page 2

Page 3

Table of Contents

1. Features 3

2. Speciﬁcation

3. Self Test

4. User Switches 7

5. Command List 8

5.1. EMULATION EPSON TM-U200

5.2. EMULATION CITIZEN iDP-3540

5.3. EMULATION STAR SP200

6. Interface 11

6.1. Interface Connector 11

7. Cash Drawer Connector 13

8. Electrical Speciﬁcations

9. Dip Switch Settings 15

Page 4

1. Features

♣Dip Switch Configuration

Emulation mode, communications mode, baud rate, serial/parallel handshake, and head printing characteristics are all configured through dip switch settings.

♣Data Buffer

The Jus' Bill RP-35 printer has a built-in 16 Kilobyte I/O buffer allowing the host computer to free itself after sending the print data.

♣Reliable communications

The Jus' Bill RP-35 supports multiple baud rates, protocols, and handshaking on its parallel & serial interfaces.

♣User controls

A power switch, a paper feed switch, power LED and Paper Low/Out error LED provide ease of use.

♣Self Test Mode

A comprehensive self-test mode is available which describes the printer configuration and dip switch setting information along with the version number of firmware installed.

♣Print orientation

The printer is capable of printing normal and upside down, the print orientation is selected by software commands.

♣Selectable international characters

The Jus' Bill RP-35 supports international characters selectable by software control.

♣Multiple Fonts/Sizes

Two different resident fonts are available for printing diversity. Each of these fonts can be printed in normal, double wide, double height, and quadruple sizes. Both fonts and sizes are software selected.

♣Bit image graphic

Two formats for bit mapped graphics are provided.

♣Error detection

The Jus' Bill RP-35 can detect paper-out and paper-jam as well as paper near-end, controller malfunction, and cover open status.

♣Peripheral Drive

Two cash drawer drivers are provided.

♣Certification

(1) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) this device may not cause harmful interference , and

2) this device must accept any interference received , including interference that may cause undesired operation. (2) UL/cUL (UL 60950-1) (3) MIC (4) CE-EMCD (CE-EMCD Class B should use Parallel shield Cable complied with IEEE-1284 standards) (5) RoHS (TUV)

(6) CCC

Page 5

2. Specification

Printer Specifications

MODEL Jus' Bill RP-35

PRINT METHOD 9-pin serial impact dot matrix

PRINT DIRECTION Bi-directional (with logical seeking)

NO. OF COLUMNS

FONT SIZE 7 x 9, 9 x 9 dots

LINE SPACING

PRINTING WIDTH

PRINT SPEED 5 Line / Sec (at 40 cpl)

INK RIBBON

PAPER

DATA BUFFER

CASH DRAWER DRIVER 2 circuits (24V, 1A max)

INTERFACE

EMULATION

POWER SUPPLY

OPERATING CONDITION 5°C to 40°C, 10% to 80% RH

STORAGE CONDITION -20°C to 60°C, 5% to 95% RH

RELIABILITY

DIMENSIONS

WEIGHT

Media Roll Paper

Width 76.2mm (3.0”)

Diameter 76mm (3.0”) max.

Copies

Type External Adaptor

Input 120VAC, 230VAC

Output 24VDC X 2.5A

MCBF 18 million lines

Printhead 150 million characters

Cutter 157(W) X 245.12(D) X 153.1(H)mm

Non cutter 157(W) X 245.12(D) X 153.1(H)mm

Cutter 5.24 lbs (2.38 kg)

Non cutter 4.96 lbs (2.25 kg)

Epson Mode : 42/35, 40/33, Star Sp200 : 42/35

Other Modes : 40/32

n/144 inch

63.5mm (2.5”)

EPSON, ERC-38 compatible

Black or Purple, Black/Red

3-ply max. (0.2mm or 0.008” thick) One Original and one copy

16K bytes

RS-232C Serial (25Pin) USB USB Combo Ethernet Wireless Lan Centronics Parallel (36Pin) Epson TM-U200, Citizen iDP-3540

Star SP200

Page 6

Overall dimension

Page 7

3. Self Test

While pressing the paper feed switch for more than 10 seconds after the printer in turned on, the self test mode is initiated. The printer self test includes a listing of the current default settings, read and write test of internal RAM, checksum test of internal program memory, loop back detection statement, a staggered dot line, a few lines of rotating character set, and a diagnostic report. The printer then enters into the On-Line mode.

Configuration Setup

When the paper FEED switch is pressed and released instantly as the power is applied to the printer, the printer will print the current printer configuration settings along with the DIP switch information. If the printer setup needs to be changed, turn the Power Off before changing the setting.

The printer will be setup at the factory as follows;

Printer is setup as follows:

Model : Jus' Bill RP-35 Firmware : Ver X.XX Interface : Serial Emulation : Epson TM-U200 CR Character : CR=CR only Flow Control : DTR/DSR Data Bits : 8 Bits Parity : None Baud Rate : 9600 CPL : 40/33 Char / Line Two Color : Installed Auto Cutter : Installed / Not Installed Journal : Installed / Not Installed

Page 8

4. User Switches

Panel Switches

Paper Feed button : Pressing the PF button momentarily will advance the paper one character line and pressing it continuously will cause a fast feed at 15 lines per second.

Power Switch

A Power switch located on the lower left side of the printer is used to turn the printer on/off.

Indicators

This section explains the different patterns signaled by the two LED indicators located on the top cover of the Jus' Bill RP-35.

STATUS

Power Off

Power On

On line ON OFF OFF Normal error-free mode

Paper low

Cover open ON Flash OFF Close cover

Paper empty

Paper jam

Test mode

LED1 LED2 LED3

GREEN RED RED

OFF OFF OFF Normal power is not supplied to the printer

Flash ON ON Normal power is supplied to the printer

ON OFF ON Insert new paper roll

ON Flash OFF Insert new paper roll

ON OFF

OFF ON

ON ON OFF Ignored Paper Low

OFF Impossible to recover

REMARKS

Page 9

5. Command List

5.1. EMULATION EPSON TM-U200

Command Hex Code Description HT <09>H Horizontal tab LF <0A>H Print and line feed CR <0D>H Carriage Return DLE EOT DLE ENQ <10>H<05>H<n> Real-time request to printer ESC SP <1B>H<20>H<n> Set right-side character spacing ESC ! <1B>H<21>H<n> Set print mode ESC % <1B>H<25>H<n>S Select/cancel user-defined character set ESC & <1B>H<26>H Define user-defined characters ESC * <1B>H<2A>H Select bit-image mode ESC - <1B>H<2D><n> Turn on/off underline mode ESC 2 <1B>H<32>H Select 1/6 inch line spacing ESC 3 <1B>H<33>H<n> Set line spacing ESC < <1B>H<3C>H Return home ESC = <1B>H<3D>H<n> Select peripheral device ESC ? <1B>H<3F>H<n> Cancel user-defined characters ESC @ <1B>H<40>H Initialize printer ESC D <1B>H<44>H<n> Set horizontal tab positions ESC E <1B>H<45>H<n> Turn on/off emphasized mode ESC G <1B>H<47>H<n> Turn on/off double-strike mode ESC J <1B>H<4A>H<n> Print and feed paper ESC R <1B>H<52>H<n> Select an international character set ESC U <1B>H<55>H<n> Turns on/off unidirectional printing mode ESC a <1B>H<61>H<n> Select justification ESC c 4 <1B>H<63>H<34>H<n> Select paper sensor to stop printing ESC c 5 <1B>H<63>H<35>H<n> Enable/disable panel button ESC d <1B>H<64>H<n> Print and feed n lines ESC p <1B>H<70>H Generate pulse ESC t <1B>H<74>H<n> Select character code table ESC { <1B>H<7B>H<n> Turn on/off upside-down printing mode GS I <1D>H<49>H<n> Transmit printer ID GS a <1D>H<61>H<n> Enable/disable Automatic Status Back GS r <1D>H<72>H<n> Transmit status

<10>H<04>H<n> Real-time status transmission

Page 10

5.2. EMULATION CITIZEN iDP-3540

Command Hex Code Description BEL <07>H Drive pulse setting command for 1st drawer CAN <18>H Clear data in buffer LF <0A>H Paper feed FF <0C>H<n> Paper feed n lines CR <0D>H Print command SO <0E>H Select expanded character mode SI <0F>H Select normal character mode DC1 <11>H Initial set command DC2 <12>H Inverted print mode DC3 <13>H Red color print command ESC BEL <1B>H<07>H<n> 1st drawer driver command SUB <1A>H 2nd drawer driver command ESC - <1B>H<2D>H<n> Select underline mode ESC * <1B>H<2A>H<n> Graphic command ESC 1 <1B>H<31>H Set 1/9 inch line feed ESC 2 <1B>H<32>H<n> Set 2/9 inch line feed ESC C <1B>H<43>H<n> Set page length ESC N <1B>H<4E>H<n> n line skip perforation command ESC O <1B>H<4F>H Cancel skip perforation command ESC P <1B>H<50>H<n> Select full-cut / partial-cut ESC f <1B>H<66>H Form feed FS <1C>H 1st drawer drive command

Page 11

5.3. EMULATION STAR SP200

Command Hex Code Description

BEL <07>H

CAN <18>H Cancel print data in buffer LF <0A>H Line feed CR <0D>H Line feed (same as LF) SO <0E>H Select expanded character mode SI <0F>H Cancel expanded character mode FS <1C>H Immediate drive command “B” for peripheral unit 1 DC4 <14>H Cancel expanded character mode

ESC BEL n1 n2

ESC @ <1B>H<40>H Initialize printer

ESC M <1B>H<4D>H

ESC R n <1B>H<52>H<n> Select international character set ESC P <1B>H<50>H Select 9 x 7 (Half dots) character size

ESC W 1

ESC W 0

ESC a n <1B>H<61>H<n> Feed paper n lines

<1B>H<07>H<n1><n2>

<1B>H<57>H<31> H<1B>H<57>H<1> <1B>H<57>H<37> H<1B>H<57>H<0>

Differed drive command “A” for peripheral unit (Default setting)

Adjust drive pulse width for peripheral unit (Default setting)

Select 7 x 7 (Half dots) character size (Default setting)

Select expanded character mode

Cancel expanded character mode

Page 12

6. Interface

6-1. Interface Connector

<D-SUB 25 Female Serial> <Centronics Parallel>

Serial Interface

PIN SIGNAL I/O DESCRIPTION 2 TXD Output Printer transmit data line RS-232C level 3 RXD Input Printer receive data line RS-232C level 4, 20 6 DSR Input Data Send Ready 1, 7

USB Interface

PIN SIGNAL I/O DESCRIPTION 1 +5V - +5V 2 DATA- - Printer transmit data line 3 DATA+ - Printer transmit data line 4 GND - System Ground

DTR Output Printer handshake to host line RS-232C level

GND - System Ground

Page 13

Centronics Parallel Interface

PIN SIGNAL I/O DESCRIPTION 1 STROBE- Input Synchronize signal Data received 2~9 DATA0~7 Input/Output Data bit Transmitted 0~7 10 ACK- Output Data receiving completed. 11 BUSY Output Impossible to print of data receiving. 12 PE Output Paper empty 13 SELECT Output Printer status for ON/OFF line 14 AUTO FEED- Input Paper auto feed signal 15 GROUND - System ground 16 GROUND - System ground 17 NC 18 LOGIC-H - +5V 19~30 GROUND - System ground 31 INIT- Input Initialize 32 ERROR- Output Printer error 33 GROUND - System ground 34 NC 35 +5V - +5V 36 SELLECT IN- Input Printer select signal

Ethernet Interface

PIN SIGNAL I/O

1 Data Out + Output Data + 2 Data Out - Output Data 3 GND Ground 4 Data IN + Input Data + 5 Data IN - Input Data 6 N.C 7 N.C 8 N.C

Page 14

7. Cash Drawer Connector

The Jus' Bill RP-35 can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is capable of supplying a maximum current of 1.0A for 510 ms or less, when not printing.

PIN SIGNAL DESCRIPTION 1 Signal GND 2 Drawer kick-out drive signal 1 Output 3 Drawer open/close signal Input 4 +24V 5 Drawer kick-out drive signal 2 Output 6 Signal GND -

Page 15

8. Electrical Specifications

The Jus' Bill RP-35 requires a power supply with the following parameters. A linear power Adapter is included in the Jus' Bill RP-35 box.

Power Supply Voltage : 24VDC±10% Power Supply Current : 2.5 A

Page 16

9. Dip Switch Settings

This table gives the definition for the DIP switch settings.

Function Setting

Epson TM-U200

Emulation

Epson TM-U300 Citizen iDP3540 Star SP200

1 2 3 4 5 6 7 8

OFF

SW1

········

CR Character

CPL

Auto Cutter

2Color

S E

Journal

Function Setting

Flow Control

Baud Rate

Data Bits

Parity

Auto Melody

CR=CR Only CR=CR + LF

40/33 Char/Line 42/35 Char/Line

Not Install Install

DTR/DSR Xon/Xoff

38400 19200 9600 4800

8 Bits 7 Bits

None Odd Even

Not Install Installed

OFF

SW2

1 2 3 4 5 6 7 8

OFF

Page 17

Function Setting

Emulation

CR Character

CPL

Auto

Cutter

L L

2 Color

E L

Journal

Function Setting

Auto Melody

Epson TM-U200 Epson TM-U300 Citizen iDP3540 Star SP200

CR=CR Only CR=CR + LF

40/33 Char/Line 42/35 Char/Line

Not Installed Installed

Not Install Installed

SW1

1 2 3 4 5 6 7 8

OFF

SW2

1 2 3 4 5 6 7 8

OFF ON

Page 18

Page 19

Rev. 1.0