Tuxedo Touch TUXWIFIS, TUXWIFIW Quick User Manual

TTuuxxeeddoo TToouucch

LED Operation

6280-001-V0

FLASHING – The system contains new
message(s) for the User.

OFF – No new messages.

RESET BUTTON

Press to reset keypad

ON – System is armed.
OFF – System is not armed.

ARMED (RED) LED

READY (GREEN) LED

ON – System is disarmed and ready to arm.
OFF – System is armed or disarmed but not

ready. If disarmed, faults or troubles are present.

MESSAGE (YELLOW) LED

SD/SDHC CARD Slot

General Information

Router

Lamps

Door
Locks

Thermostat

Window Shades

74°

IP Cameras

LAN

Wireless

WPS

Reset

Internet

WAN

Security

Power

ms_controller-004-V0

CONTROLLER

Security Automation

MultiMedia

Saturday

02:50PM

03/23/2013

HOME

IP:NA

Humidity N/A

Wind Cond N/A

Unknown City

Temp N/A

h

TTM

M

MMooddeellss TTUUXXWWIIFFIISS && TTUUXXWWIIFFIIW

W

Home Automation System

Quick User Guide

For additional information see the full User Guide [800-16573V1 7/14 Rev. A] available online at:

http://www.security.honeywell.com/hsc/products

Congratulations on your ownership of a Honeywell
Tuxedo Touch™ Home Automation System which
combines home Security and home Automation.

Equipped with Wi-Fi® capability and built-in Z-Wave®
technology, Tuxedo uses your home Wi-Fi network to
communicate with Wi-Fi enabled devices allowing
control of Z-Wave® devices, (cameras, lights, door
locks, and thermostats, etc.)

Your "Home" screen is displayed most of the time
and can be customized via the Multimedia
Application. From this screen you can control:

• the security system

• multimedia applications (video, pictures and

cameras)

• home automation (lighting, thermostat and door
locks).

NOTE: For optimum viewing of screens and
menus, the device’s font size setting may need to
be adjusted.

Icon Descriptions

Press the “Product/Training Video” icon (located on the Home screen) to assist with the setup of the system.

Home - Returns you to the Home screen.

Security- Arm the system and access the
three arming modes.

Automation - Access Z-Wave setup, Scene
setup, and Room/Group setup screens.

Multimedia - Access the Message, Camera,
Picture and Video features.

Setup - Access the Setup menus; IP setup,
System setup, Display & Audio setup and
Account.

Weather - Select to access weather settings.

Panic – Displays Emergency functions (as
programmed by the installer). Note: This icon
is displayed and active on all screens except
while in the Clean Screen mode, during an
LCD Display test in Diagnostics and from the
Video and Camera screens.

Video - Allows user to set up and play video files.

Picture - Allows user to display personal photo(s)
as wallpaper or in a slide show format.

Message - Record / retrieve Voice Messages.

Annunciate Status - Allows user to hear system
status.

Camera – Select to set up and view cameras.

Event View – Select to access video recordings.

Control Panel Message – This icon alerts the
user to a Control Panel Message.

User Setup – Add, Delete, Edit a User

Each user must be assigned a name with a corresponding 4-digit user code in order to gain access to various features and

functions.

Select Setup ˃ System setup ˃ USER SETUP˃ ADD USER.
Select each field and enter the appropriate information; select Save when done.
Follow this procedure for deleting and editing users.

Night Setup - Change arming modes

The NIGHT function can be set to arm the system in one of five arming modes. To change the arming mode, select Setup ˃

System setup ˃ Advanced Setup ˃ Night Setup: choose from:

Away - Stay - Instant (default) - Night (Residential Only) – Maximum.

Arming the System

You can arm the system in one of three arming modes: Away, Stay, and Night.

AWAY – Select to arm when no
one is staying on the premises.

IMPORTANT: If you return to your home or business and the main burglary sounder is on, DO NOT enter the premises, but call
the police from a nearby safe location. If you return to your home or business after an alarm has occurred and the main sounder
has shut itself off, the controller beeps rapidly upon entering, indicating that an alarm has occurred during your absence. LEAVE

IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.

To Arm the System: Select SECURITY .
Notes:

1. If Quick Arm is Not enabled in your system, a message to enter your User Code is received.

2. When the system is armed for Stay, Night Stay and Instant mode, Tuxedo beeps 3 times.

3. When the system is armed for Away and Maximum mode, you will hear steady beeps then rapid beeping during the last 10
seconds of Exit Delay.

4. For CP-01 installations, Maximum Mode cannot be used.

To Arm Multiple Partitions: Select SECURITY
Notes:

1. A user may have access to some or all of the available partitions.

2. If the user code is accepted, the system displays the partitions that the user has access to.

3. If any zones are bypassed, a “Faulted Zones” ( ) icon is displayed on this screen.

Disarming the System

To disarm the system when already in the premises select the Disarm icon and enter your 4-digit user code.

To disarm the system when entering the premises enter your 4-digit user code.

To disarm Multi-Partitions - From the Home screen, select the Security, Arm Multi-Partition and Disarm
icons; enter your 4-digit user code.

STAY - Select to arm when you are staying home,
but might expect someone to use the entrance door
later.

˃ Arm Multi-Partition .

NIGHT - Select to arm when you are

staying home and do not expect anyone
to use the entrance door.

Display Faulted Zones / Bypass Zones

How to Display Faulted Zones – Select the SECURITY

How to Bypass Zones - Select SECURITY ˃ MORE CHOICES ˃ SHOW ZONES .
Notes:

1. Some systems do not allow you to bypass fire, carbon monoxide or emergency zones. On certain fire control systems, a

specified user may be allowed to bypass fire, carbon monoxide and system zones if the user was enabled by your system
installer.

2. Limits apply as to how many zones can be bypassed at one time. These limits are ten zones on residential systems and five

zones on commercial systems.

˃

FAULTED ZONES .

- 2 -

Panel Faults

If the following Panel Fault icons are displayed on the Security screen, contract your alarm company.

Low Battery

LRR Supervision Failure

Wireless Failure

Panic

Telco-1 Cut

AC Loss

Bell Failure

Pager Failure

Expander Failure

Exceeds Max Attempts

Telco-2 Cut

Weather Forecast – Set a location

1. Press the Weather feature on the “Home” screen.

2. Select USA/Canada, Zip Code/Postal Code and enter the information on the data entry keyboard; Select OK.

Voice Messages

Select Multimedia ˃ Message ˃ Record . Record your message (stay within approximately one foot of the

controller) and speak at a normal voice volume. Select Stop when done. To retrieve a voice message, select from the

message list and then select Play Message . Select Pause to pause the playback.

The Message LED will continue to flash until all new messages have been played back.

Multimedia

Using Cameras

1. Select Multimedia ˃ Camera ; images from installed cameras appear.

2. Select Quad View to view up to four cameras on the same screen. Select a quadrant area on the screen and then select
the camera that you want to appear in that quadrant.

Select Full View to display a larger view of the image. For pan/tilt style cameras, select Pan/Tilt and Auto Pan

to control the camera.

Select Record to begin a recording, then select Stop to end a recording; a media (SD/SDHC) card is required.

Notes:

1. QuickTime® media player must be installed on your PC.

2. Camera viewing is not compatible w/Opera web browser.

Play Videos:

While viewing videos in Full View, press anywhere on the screen to exit.

Select Multimedia ˃ Video and insert a media (SD/SDHC) card (with stored video files). Maximum video resolution

should not exceed 640 x 480. Highlight a video file from the list and select Play .

- Select Repeat to continually replay selected video.

- Deselect Repeat to play the list of video files starting with the first video and ending with the last.

- Use the icons to: Pause ; view a Full View .

* Note: See the Video Converter document to convert videos for proper playback (provided in the carton).

Customize the Home Screen:

The controller can display personal photo(s) on the Home screen as wallpaper or in a slide show format.

Select Multimedia ˃ Picture . Insert a media card (SD/SDHC) with up to 1000 stored (.bmp or .jpg) photos.

1. Set up a Slide Show: select a photo from the file list that you want to display and select Add Image . Repeat this for each

photo you want to add.

• Select the viewing Transition arrow; select Standard, Horizontal, Vertical, and Fade Out.

• Select the Slide Delay arrow to select a time interval for viewing each picture.

While viewing photos in Full View, select anywhere on the screen to exit.

- 3 -